TM
A GREEN ENER GY COMPANY
AE LED ULTIMATE
T8 LED TUBE
DIRECT PLUG & PLAY WITH ELECTRONIC
BALLAST, ELECTRONIC-MAGNETIC
BALLAST, OR DIRECT WIRE
CO M PAT I B I L I T Y
C E R T I F I C AT I O N S :
Direct replacement for traditional fluorescent
lamp. No need to replace current ballast or rewire.
BALLASTS
Compatible with most brands electronic and
electro-magnetic ballasts, including rapid start and
TM
E479989
instant start
AC INPUT
WARRANTY: 5 YEARS
Will work directly from 100-277VAC
R AT E D L I F E : 5 0 , 0 0 0 H O U R S
HEALTH
Flicker Free, Low Glare
A P P L I C AT I O N S
SCHOOL
OFFICE
H O S P I TA L
W W W. AT L A N T I C L E DCO. CO M
SUPERMARKET
R E TA I L
COMMERCIAL
PHONE: 516.737.1500
AE ULTIMATE T8 LED TUBE
1 . F E AT U R E
Compatible with most brands electronic ballast.
2. PRODUCT DIMENSIONS
L
D
4FT
D
CAP-BASE
1161
1197mm
27.8mm
G13 fixed end caps
L1
18.5
PRODUCT LENGTH
L(MM)
D(MM)
A(BASE)
4FT
1197
27
G13
3 . P R O D U C T S P E C I F I C AT I O N E L E C T R I C A L C H A R AC T E R I S T I C S
HUMIDITY
Operating 10%-80%
Storage 10%-80%
TEMPERATURE
Operating -4°+140° C
Storage -4°+140° C
Ballast Input Voltage: AC100~277V50/60Hz
PF:>0.9, THD<20%
Power Efficiency: 88%
A E U L T I M AT E T 8 L E D T U B E
ITEM
WATTAGE
LED QTY
CRI
CCT
BEAM ANGLE
AELED4FT8FBG15469
18W
120PCS
2835LEDS
>80
4,000K
5,000K
130°
COVER
LENGTH
FROSTED
1197+/-1mm
OR CLEAR
TM
A GREEN ENER GY COMPANY
AE ULTIMATE T8 LED TUBE
5 . I N S TA L L AT I O N I N S T R U C T I O N S
A. CONNECTION DIAGRAM
POWER
SOURCE
CONNECTION DIAGRAM
T8 ELECTRONIC BALLAST
ELECTRONIC
BALLAST
(2 TUBES)
LAMP HOLDER
LED T8 TUBE 1
LAMP HOLDER
LAMP HOLDER
LED T8 TUBE 2
LAMP HOLDER
T8 ELECTRONIC -
ELECTRONIC-
MAGNETIC BALLAST
AC LINE
VOLTAGE
MAGNETIC
BALLAST
LAMP HOLDER
LED T8 TUBE
LAMP HOLDER
AC LINE VOLTAGE
100-277VAC
DIRECT
LINE
V O L TAG E
LAMP HOLDER
LED T8 TUBE
LAMP HOLDER
TM
A GREEN ENER GY COMPANY
AE ULTIMATE T8 LED TUBE
B . I N S TA L L AT I O N G U I D E
1. TURN POWER OFF
2. REMOVE
FLUORESCENT TUBE
3 . I N S TA L L L E D T U B E
I N TO F I X T U R E
4. TURN POWER ON
Please take the time to read this quick installation guide. The guide contains important
information and notes regarding the installation and operation.These tubes should be installed
only by qualified personnel.
• Product is not dimmable
• Modifications to the product void the warranty
• Suitable to replace fluorescent lamps as specified on the product label
1. This type of T8 tube is G13 base
2. This tube light works with instant start electronic ballast & electro-magnetic ballast &
directly links to 100-277V without ballast
3. This tube light is double-ended powered not dimmable
4. CAUTION: MAKE SURE THE POWER SUPPLY IS OFF DURING INSTALL
5. For indoor use only, risk of electronic shock. For use in dry locations only, not for use in
sealed enclosures.
6. Do not use sharp tools near or on the surface of the device
7. May not be compatible with some ballast types
8. Pay attention to the path of electrical current on the lamp holders
A. There are two paths of electrical current: non-shunted & shunted
B. Shunted socket required. If the socket is non-shunted, you should ask a licensed
electrician to make it shunted
CAUTION: IF THE LAMP OR LUMINAIRE EXHIBITS UNDESIRABLE OPERATION ( BUZZING,
FLICKERING, ETC.), IMMEDIATELY TURN OFF POWER, REMOVE LAMP FROM LUMINAIRE AND
CONTACT MANUFACTURER.
CAUTION: RISK OF FIRE- DO NOT INSTALL THIS LAMP IN A PRE-HEAT LUMINAIRE. THIS LAMP
ONLY OPERATES ON ELECTRONIC BALLASTS. IF LAMP DOES NOT LIGHT WHEN THE LUMINAIRE
IS ENERGIZED, REMOVE LAMP FROM LUMINAIRE AND CONTACT LAMP MANUFACTURER OR
QUALIFIED ELECTRICIAN