Note: For proper ESC operation, please adjust transmitter as follows
Set High EPA or ATV to maximum setting; max throttle
Set Low EPA or ATV to maximum setting; max brake
Set throttle trim in the middle position
Set throttle Exponential to Zero.
Set Throttle mode F50/B50 for Practice Mode.
Set Throttle mode F70/B30 for Racing Mode.
Transmitter Calibration:
Press and hold the push button and then turn on ESC switch - Green LED on
GreenLED flashing and then solid on.
Pull to Full Throttle
Red LED flashing and then solid on.
Push to Full Brake
Neutral
Red & Green LED flashing, and then on,about 2sce All LED solid Off.
Switch Power off, then turn on again, the ESC be ready to work.
Normal Operation:
Green and Red LED on for Forward with pause then Reverse
Red on for Forward Only
As Battery voltage get to warning point, Red LED blink.
As temperature voltage get to warning point, Green LED blink.
Default Settings:
Battery Type
-
Auto Detec
Operation Mode
-
Forward with pause then Reverse
Initial Braking
-
10%
Drag Brake
-
0%
Motor Timing
-
Normal
Acceleration
-
Medium
Throttle Limit
-
0%
Reverse Limit
-
50%
Operating Frequency
-
Deadband
4
-
Rotation Reverse -
8KHz
Normal
4. How to set ESC?
A. Press and hold SW1 until Green LED flash one time，and then release，Red
LED starts flashing，Enter [Battery Type] setup。[Number of Red LED Flashing
indicates current setting]。
[ Battery Type ]：
Nimh/Nicd
Lipo Auto Detect
*
**
[ Red LED flashes one time ]
[ Red LED flashes two times ]
Quickly press SW1 to choose different setting, long press SW1 will store the
setting and exit the setup
B、Press and hold SW1 until Green LED Flashes two times，and then release，Red
LED starts flashing，Enter [ Operation Mode ] setup。[Number of Red LED
flashing indicates current setting]
[ Operation Mode ]:
Forward Only
Forward with Reverse
*
**
[Red LED Flashes one time]
[Red LED flashes two times]
Quickly press SW1 to choose different setting, long press SW1 will store the
setting and exit the setup
C、Press and hold SWI until Green LED Flashes three times，and then release，Red
LED starts flashing，Enter [Initial Brake ] setup。[Number of Red LED flashing
indicates current setting]
[ Initial Brake ]:
10%
20%
30%
40%
50%
60%
70%
80%
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
[Red
[Red
[Red
[Red
[Red
*
[Red
* * [Red
* * * [Red
LED
LED
LED
LED
LED
LED
LED
LED
Flashes
Flashes
Flashes
Flashes
Flashes
Flashes
Flashes
Flashes
one time]
two times]
three times]
four time]
five times]
six times]
seven times]
eight times]
Quickly press SW1 to choose different setting, long press SW1 will store the
setting and exit the setup
D、Press and hold SW1 until Green LED Flashes four times，and then release，
Red LED starts flashing，Enter [ Rotation Reverse ] setup mode。[Number of
Red LED flashing indicates current setting]
[ Rotation Reverse ]:
Normal
Reverse
*
**
[ Red LED Flashes one time]
[ Red LED Flashes two times]
Quickly press SW1 to choose different setting, long press SW1 will store the
setting and exit the setup
E、Press and hold SW1 until Green LED Flashes five times，and then release，
Red LED starts flashing，Enter [ Default Settings ] setup mode。[Number of Red
LED flashing indicates current setting]
[ Default Settings]:
No
Yes
*
**
[ Red LED Flashes one time]
[ Red LED Flashes two times]
Quickly press SW1 to choose different setting, long press SW1 will store the
setting and exit the setup
Programming BOX set flow Chart：
Hextronik[CAR]
PROGRAM BOX v1.0
8TH sensorless
Ver: 1A260101
Battery Type
Lipo Auto Detec、Nicd/Nimh
Operation Mode
Forward/Reverse、Forward Only
Initial Brake
10%、20%、30%、40%、50%、60%、70%、80%
Drag Brake
0%、4%、8%、12%、15%、20%、25%、30%
Motor Timing
Low、 Normal、 High
Acceleration
Forward Limit
Reverse Limit
Drive Frequency
Dead Band
Rotation Reverse
Defaults
Low、 Medium、 High
0%、10%、20%、30%、40%、50%、60%、70%、80%、90%
10%、20%、30%、40%、50%、60%、70%、80%、90%、100%
8KHz、 16KHz
2、3、4、5、6
Normal、 Reverse
NO、 Yes
Saving…….