Charcoal Grill
z
SKU# SKY 1845
ASSEMBLY MANUAL
Revised May2015
The parts and hardware below have been included for assembly:
(A) x 1
(B) x 1
(C) x 1
(D) x 1
(G) x 1
(H) x 2
(I) x 1
(J) x 1
(K) x 1
(L) x 1
(M) x 1
(N) x 1
(O) x 2
(P) x 4
(Q) x 1
(R) x 1
(V) x 3
(W) x 2
(U) x 3
(X) x 1
(Bolt A) x 14
(Bolt B) x 15
(Bolt C) x15
(Bolt D) x 4
(Steam Cap) x 1
(Tire Nut) x 2
(Bolt E) x 4
(Washer) x 2
(Spring) x 1
(E) x 1
(F) x 2
(S) x 2
(dd) x 3
(T) x 2
(Y) x 1
WARNING:
(Z) x 1
(aa) x 1
(bb) x 1
(cc) x 1
(dd) x 2
Manufacturer and seller expressly disclaim any and all liability for
personal injury, property damage or loss, whether direct, indirect, or
incidental, resulting from the incorrect attachment, improper use,
inadequate maintenance, or neglect of this product.
ASSEMBLY STEPS:
1
2
3
Front
Back
10
11
12
Part Z
Start by sliding part (A) into part
(C), making sure the 2 holes on
the side of both legs are facing
forward (shown with red circles).
This will be the front of the grill.
4
Attach part (B) by sliding it into
part (D) to complete the back of
the grill.
5
Using 4 nuts and bolts from (bolt
A) attach part (I) to the assembly
as shown. Do not fully tighten.
7
Lay part (K) onto the assembly
and secure using 2 (bolt A’s). Do
this to both sides of part (K).
13
6
Using 4 nuts and bolts from (bolt
A) attach part (J) to the assembly
as shown. Adjust the assembly
to preference and tighten all nuts
and bolts.
8
14
Connect the bottom of part (L) to
part (I) with (2 bolt Bs).
Locate the circular hole on the
top of part (K) and attach part (X)
using 3 (bolt C’s). Slide part (Y)
over part (X) with the (spring) and
secure using the (steam cap).
Note: there is an extra nut added for this
part.
15
Attach part (W) to part (K) with
4 (bolt B’s). Lay 3 small wood
beams (part V) across and secure
using (bolt C).
Lay 3 wood beams (part U)
across part (S) and connect using
(bolt C).
17
16
Attach part (Q) and part (R) to
part (L) using 3 (bolt B’s). Attach
part (Z) using a nut from (bolt B).
Attach the handles to the lid
by sliding (bolt D) through the
handle, part (O), and then slide
part (P) over (bolt D) as shown.
Attach part (T) to the front assembly using 2 (bolt A’s) and then
attach part (S) to part (K) with 2
(bolt B’s) as shown.
Next, Slide part (G) into the lower
holes located at the bottom of the
assembly. Slide on the wheels,
part (H) with 2 (washers) and
tighten using 2 (tire nuts).
9
Connect part (L) to part (K) using
6 (bolt B’s).
Next, slide the lids, part (M) and
part (N), into the holders and
secure using 4 (bolt E’s).
Next, slide part (F) through one
end of part (E) and wedge
between the front and back
assembly as shown. Repeat this
process on the opposite side.
18
Unscrew the nut located on thermostat, part (CC), slide it in the
designated hole on part (M) and
secure.
Lastly, feed the grease catcher,
part (BB), through the hole on the
inside of part (K), and place part
(AA) on top.
Call Us!
We’re here 7 days a week to help you!
(909)-948-8400
Monday-Friday 5:00am-5:30pm pst
Saturday and Sunday 7:00am-3:30pm pst