I n s ta ll ati o n I n s tr u c ti o n s
Bionic™ 4 — Standard/Continuous X1, X2, X6
5˝
5"
5"
5˝
6-7/16˝
61 2"
5 "7
5/16˝
1
2
1-1/16˝
11 16"
4-4 3/"32˝
6"
6˝
1
4-3/32˝
6˝
41 16"
16
T-bar
6"
Flush Lens
Regressed Lens
Parts shipped separately
1) Identify luminaires:
Start/End units are capped
.437
2.562
END VIEW
SCALE 1 : 1
75°
Reflectors
Trim Lens
X1
Star
.187 X .375 SLOT
.250
X3/X7
Start/End Unit
Scale
Drawing Size
B
VAULT
Sheet
Drawn By
Date
Check
Date
Appr
Date
Description
Finish
1.000
FRONT VIEW
SCALE 1 : 1
Of
Prudential LTG.
Project
Material
Rev
Part Number
SCALE 1 : 1
R.125 (TYP.) PICTORIAL VIEW
1774 East 21st Street, Los Angeles, CA 90058
www.prulite.com
Aligner Splines
Adjustable Hanger
Brackets
X3/X7 Start/End Unit
X1/X2/X6
X1Start/End
Start/End
Unit
T-bar Brackets
REV
Sca
Drawing Size
B
Sh
Intermediate Unit
Intermediate
Lens Removal Tool
8-32x1/4˝
Machine Screws
Fin
Prudential LTG.
Ma
1774 East 21st Street, Los
8-32x3/8˝ Self-tapping
Machine Screws
www.prulite
Notes:
1. Housing ships separated from gear tray, reflectors and lens
for easy installation
Intermediate Unit
2. Remove reflector protective coating
3. Install lamps (by others)
4. Seamless lamps may be included with Seamless orders
REV
BY
WARNING:
GroundDESCRIPTION
fixture
in accordance DATE
with localREV.
and
national electrical
REVISION HISTORY
B
codes. Failure
to doVAULT
so may result in serious personal injury.
We reserve the right to change details of design, materials and finish in any
way that will not alter installed appearance or reduce function or performance.
LTG.shipped in bulk.
All Prudential
hardware
Drawing Size
Scale
Sheet
Drawn By
Date
Check
Date
Appr
Date
Of
Finish
Project
Description
Material
Rev
Part Number
1774 East 21st Street, Los Angeles, CA 90058
www.prulite.com
Page 1 of 4, Sept1-12
1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com
I n s ta ll ati o n I n s tr u c ti o n s
Bionic™ 4 — Standard/Continuous X1, X2, X6
1B) Install ‘U’ shaped end trim
Straight trim installed after housing is up
1C) Install Aligner Splines on housing
Two at every joint on - outside or inside housing
with #8 screws
U-SHAPED TRIM
INSTALL
Note: 6´ or smaller units have framed trims
Top view of Option A Installation hole spacing
2) Secure luminaire to structure
(multiple options)
A)
B)
X
Y
1/4-20 can
protrude into
housing no
more than 3/8˝
Y
X= 2´
Y = 9˝ from center hole
X= 3´
Y = 15˝
X= 4´
Y = 21˝
X= 5´
Y = 27˝
X= 6´
Y = 33˝
X= 7´
Y = 39˝
X= 8´
Y = 45˝
Safety Strap
DO NOT REMOVE Shipping strap
Page 2 of 4, Sept1-12
1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com
Slots Staggered Regressed
T-Bar x1
I n s ta ll ati o n I n s tr u c ti o n s
Bionic™ 4 — Standard/Continuous X1, X2, X6
2A) If additional holes are drilled in top plate for 1/4-20,
3) Fasten Inside Joiner Brackets
support with 8 screws at closest location to new holes
#
WARNING! Failure
to properly install
top plate screws
will void warranty
8-32x3/8” self-tapping
machine screw
8-32x1/4” (provided)
4) Slide & tighten aligner splines over joint
5) Snap “Gear Trays” into housing
Leave space between Gear trays for Quick Connects
6) Plug in Quick Connect QDMs
7) Slide Gear Trays together
Gaps at ends should be equal, see RUN INFO for appropriate spacing
Page 3of 4, Sept1-12
1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com
I n s ta ll ati o n I n s tr u c ti o n s
Bionic™ 4 — Standard/Continuous X1, X2, X6
8) Install Cross Brace Brackets
over Gear Trays every 4’
9) Remove shipping support brackets
8-32x1/4” screws
WARNING! Failure to properly install
Cross Brace Brackets will void warranty
10) Install reflectors
Slots Staggered Regressed T-Bar x1
11) Install straight trim, cut last piece to fit
Light Engine
Use filler reflector as needed, trim to fit
12) Install lamps (by others)
13) Install lensing, cut last piece to fit
Note: Leave 1/16˝ air gap at each end of run
Table saw or chop saw with a 80T blade recommended
Page 4 of 4, Sept1-12
1774 East 21st Street, Los Angeles, CA 90058 • 213-746-0360 • www.prulite.com