Catalog Number Notes Type Wallbox Dimmers FEATURES ISD BC INTENDED USE To provide direct dimming and switching control of fluorescent fixtures equipped with four-wire ( 0-10 VDC) dimming ballasts. ATTRIBUTES Fluid slide movement allows fine adjustment of light level over the entire dimming range. Separate ON/OFF preset switch permits switching the lighting without disturbing the light level setting. An integral LED indicator turns ON when the dimmer is OFF to facilitate location in a dark room. ISD Series controls are compatible with the DSA Series wallplates and other Decora® style devices. CONSTRUCTION Strap-mount device is designed to fit standard single- or multi-gang switch boxes. FINISH Standard white or ivory finish devices are supplied with a single-gang Decora style wallplate. Snap-on color change kits are available allowing field color change of the device to gray, black, brown, almond, white, or ivory. Color change kits include a matching single-gang Decora style wallplate. ELECTRICAL Uses standard single-pole or three-way wiring. No neutral connection is required. Separate low voltage connection to ballast for 0 to 10-volt control signal. Dual rated for 120 and 277VAC ballast loads. For additional switching capacity, use in conjunction with LPCS 120/277 power control station. FUNCTIONAL Integral push ON/push OFF switch allows lighting to be switched ON and OFF at the level currently set by the slider. Ballast controller can be used with standard three-way and four-way switches for applications requiring control from multiple locations. INSTALLATION Wall mounts over standard single-gang switch box. Devices can be ganged into multi-gang assemblies by breaking off the scored aluminum tabs. LISTING UL Listed. CSA Certified. WARRANTY Two -year total customer satisfaction warranty. BALLAST CONTROLLER Shown with optional DSA FP D1 WH screwless wallplate (order separately) Decora® is a registered trademark of Leviton®. Example: ORDERING INFORMATION ISD BC 120/277 WH Choose the boldface catalog nomenclature that best suits your needs and write it on the appropriate line. Order accessories as separate catalog number. ISD BC 120/277 Series Type Voltage ISD BC Ballast controller 120/277 Dual voltage Color1 IV WH Ivory White Accessories NOTE: 1 ISD dimmers are supplied with standard wallplates. Order optional IV ivory or WH white screwless designer wallplates to match dimmer if desired. Order as separate item. ISD CCKIT _ _ DSA FP D# _ _ Color change kit, specify WH (White), IV (Ivory), GY (Gray), BR (Brown), BK (Black) or AL (Almond). Ivory screwless thermoplastic wallplate for ISD or Decora® compatible devices. Specify number of gangs (# =1 to 6) and color [WH (white), IV (ivory), GY (gray), BR (brown), BK (black) or AL (almond)]. Note: Consult factory for color availability in multi-gang plate configuration. Controls Sheet #: ISD-BC ISD BC Ballast Controller WIRING DIAGRAMS SPECIFICATIONS Single-Location Control Application Class 2 Conductors ELECTRICAL • Input: 120/277 VAC @ 50/60Hz (switch only). Dimmer Cap with Wire Connector Purple Gray Advance Mark VII or other compatible 0-10V dimming ballast Black Red Hot (Black) Black Red Load Line Voltage Green Ground } • • Standard three-way operation. Maximum low voltage control loading fifty (50) ballasts. • Maximum switch rating: 1200W 120VAC, 1500W 277VAC. Use with LPCS power control station for full 16A switching capacity. Operates three LPCS stations per ballast controller. No derating is required for multi-gang mounting. • White Neutral (White) Two-Location Control Application Purple Gray Hot (Black) Red Black Line Voltage Green Ground • } Load Green Ground • Advance Mark VII or other compatible 0-10V dimming ballast Black Red • Class 2 Conductors Dimmer 3-Way Switch White Neutral (White) Three-Location Control Application 4-Way Switch 3-Way Switch Hot (Black) 1 Class 2 Conductors Dimmer Purple Gray Red 2 Advance Mark VII or other compatible 0-10V dimming ballast Black 1 Black Red 2 Line Voltage Load Green Ground Green Ground Green Ground • } • Consult factory for 347VAC or low voltage only switching requirements. MECHANICAL • Captured wrap-around slide mechanism, 20mm total travel. White Neutral (White) 1 Travelers between switches "IN" 2 Travelers between switches "OUT" NOTES: 1 Class 2 conductors as part of the same system can be run with line voltage if supplied with 600V insulation. 2 Consult factory for complete class 2 installation instructions. • Air-gap push ON/OFF preset switch. ENVIRONMENTAL • LPCS - Two-Location Control LPCS Dimmer Black Red To Additional Ballast Black Blue Red Black All dimensions are inches (centimeters). Purple Gray Black Red Hot (Black) DIMENSIONS Cap off Black wire with Wire Connector 120V/277V Operating range, 0 – 55 o C, 20 – 90% relative humidity, non condensing. White Black Red Primary Side To Lamps Red Red Black Line 120/277VAC, 60Hz 0-10 VDC Ballast Green Ground Green Ground 3.28 (83.3 mm) 3-Way Switch Common Terminal (Black Screw) Compatible with Lutron Hi-Lume or ECO-10 ballasts with the LEQ FDBI interface. Blue Yellow White Red 2.68 (68.1 mm) Common Terminal (Black Screw) Compatible with Advance Mark VII®, MagneTek/ Universal Ballastar®, ESI Super Dim and SYLVANIA HeliosTM electronic ballasts. Compatible ballast control ranges (Subject to change without notice; contact ballast manufacturer for current specs.): Advance Mark VII, RZT Series 100% to 1% continuous SYLVANIA, Helios 100% to 1% continuous MagneTek/Universal Ballastar 100% to 5% continuous Lutron TVE Series 100% to 10% continuous ESI, Super Dim 100% to 1% continuous 4.15 (105.4 mm) Common Terminal (Black Screw) To Additional Ballast White Neutral (White) Multiple LPCS - Single-Location Control LPCS Dimmer Cap off Black wire with Wire Connector Red Red Black Purple Gray Red Red To Additional Ballast Red Green Ground Primary Side To Lamps To Additional Ballast Black Blue Primary Side To Lamps Red Red White Purple Gray Red Black Blue Line Red 120/277VAC, 60Hz Cap off Black wire with Wire Connector 120V/277V Hot (Black) To circuit #2 Black Black 0.38 (9.7 mm) LPCS Cap off Black wire with Wire Connector 120V/277V Hot (Red) 1.41 (35.8 mm) 2.12 (53.8 mm) Red Black 0-10 VDC Ballast White White Red Black Blue 0-10 VDC Ballast Yellow White Blue Yellow Neutral (White) Synergy Lighting Controls Sheet #: ISD-BC ©2002 Acuity Brands Lighting, Inc., 10/25/07 1335 Industrial Blvd, Conyers, GA 30012 Phone: 800-533-2719 www.synergylightingcontrols.com