FlacheSAN2 Hardware Quick Guide
Version 1.51 Release 2014-03-06
Congratulation on your purchase of EchoStreams FlacheSAN2 system!
1.
Check the content of the box. Please confirm
that your package contains the following:
#
Description
1
2U 48-Bay Enclosure
2
Drive Tray
Drive Lock
(unlocked position)
To unlock the drive lock:
Image / Description
Qty
1
2.5” Drive Trays
1. Push the
drive lock
latch inwards
Drive Status LED:
(Solid) Drive Online
(Blink) Drive Activity
(Fast Blink) Drive Locate
(Slow Blink) Rebuild
(Solid) Drive Fail
2. Then pull
it upwards
48
Tray Handle
Tray Latch
3
4
SSD (optional)
M3 Screw Set*
5
Power Cable*
6
7
Rail Kit (optional)
Bezel (optional)
8
Motherboard
(inside the chassis)
IO Card
9
for mounting
2.5” drives
2
1
1
3. Remove the top cover by removing the 4
screws on the top and sides of the unit and slide the cover
towards the back of the unit.
1
Intel S2600IP
LSI or Adaptec RAID cards
depending on order
10a Internal mini-SAS
cables SFF 80878087 (inside the
chassis)
10b Internal mini-SAS
cables SFF 80878643 (inside the
chassis)
11 ROC kit (optional)
12 Air duct (inside the
chassis)
13
48
1 set
2.5" 7mm
HDD / SSD
Tray
Used for LSI cards, optionally
installed depending on order
type
Used for Adaptec cards,
optionally installed
depending on order type
Mezzanine riser + bracket
1 set
12
12
1 set
1
Remove additional screws (blue circles) to open the
middle top cover (for fan module and backplane access)
4. Inspect the internal components of the
chassis. FlacheSAN2 system by default comes with Intel
S2600IP motherboard, an air duct, fan modules,
backplanes, IO cards, internal mini-SAS cables. Upon
request, optional items such as ROC Module, OS disk, BBU
can be provided. Note the locations of each component.
Air duct
Heat sink
Motherboard
Internal Fans x4
2
Backplanes
SSD 45-48
SSD 41-44
14
15
16
OS Disk (optional)
This quick guide
Packaging
SSD 37-40
SSD 33-36
1/2
1
1 set
SSD 29-32
SSD 25-28
SSD 21-24
* Inside the accessories box. If any items are missing, please contact
your authorized reseller or sales representative
2. Get familiar with the unit.
System Status LED:
AC Power Off
(Solid) System Healthy
(Blink) System Degraded
Eth0 LED:
Eth1 LED
Front Panel
(Blink) Non-Critical
Alarm
(Solid) Critical Alarm
Link UP /Act
Link Down
48 Drive Bay
Ear Handle
ID Button / LED:
ID On
ID Off
Power
Supply B
Power
Supply A
Serial
Port
VGA
Port
Eth0/
Mgmt
Eth1
USB
Eth2
Ports
SSD 13-16
SSD 09-12
SSD 05-08
OS Drive Location
Internal SAS cables connecting
IO card to backplane
5. Install CPU and memory (not included) to their
respective slots. Please be aware of each component’s
installation requirements and prerequisites.
For details, refer to S2600IP motherboard TPS.
Turn the ear
Eth2 LED
handle inwards
Eth3 LED
and use the
NMI Button
index finger to
Reset Button
pull the unit
Rear view of the unit
AC cable
secure lock
USB Port
IO Card
SSD 17-20
SSD 01-04
BBU
Front view of the unit
Power Button / LED:
System On
System Off
Mezzanine
IO/ROC
Module
BBU + Bracket
CPU2
CPU slots support one or
two Intel Xeon E5-2600
processor(s), LGA 2011
Socket
IO Slots
Install the
memory to the
blue slot first
farthest from
the CPU
Eth3
CPU1
Memory slots support
800/1066/1333/1600
MHz Registered DDR3
memory (RDIMM),
Unbuffered (UDIMM
and LRDIMM)
FlacheSAN2 Hardware Quick Guide
6. Install IO cards (optional) into PCI-e slots.
Connect the cards to the backplane using the mini-SAS
cables provided. Connect the first port of the IO card to
mini-SAS cable “1”, 2nd port to mini-SAS cable “2”, etc.
Connected to CPU 1
Slot 1 [3] PCIe Gen3 x16
Slot 2 [2] PCIe Gen3 x8
Slot 3 [1] PCIe Gen3 x16
Slot 4 [8] PCIe Gen3 x8
Slot 5 [7] PCIe Gen3 x16
Slot 6 [6] PCIe Gen3 x8
Slot 7 [5] PCIe Gen3 x16
Slot 8 [4] PCIe Gen2 x4
IO Module Slot
(Flex cable required)
PCIe Gen1 x4
Connected to CPU2
Connected to CPU 2
Reduced to x8 when PCIe
Slot 2 is populated
internals of the system, close the top of the chassis.
9. Remove drive trays from the enclosure (if no
SSDs are installed already).
10. Install drives into trays. Follow the diagram
closely. SSDs can be provided and installed by request.
1. Slide the drive in with the
IO connector side head first
to the back of the tray
CPU 2
4. Snap in the
hinge back to
lock position
Reduced to x8 when PCIe
Slot 8 is populated
Reduced to x8 when PCIe
Slot 6 is populated
8. Put the top cover. Once we are finished with the
3. Snug the
other end of
the drive into
the tray
CPU 1
ROC Module Slot 0 [0]
PCIe Gen3 x8
Connected to CPU1
[*] PCIe Slot IDs as seen
by Adaptec cards
To remove the disk, do the steps in reverse.
Poke from the bottom hole to help release the disk.
IO Module can also be installed to the ROC Module slot by
using a riser mezzanine card.
1. Place the IO Module to the IO
bracket. Slide one end to the card
guide, do not tighten the screws.
5
ROC Module Bracket
2
2. Secure the other end with 2
screws.
1
IO Module
3
3. Install the IO card + IO bracket to
riser card mezzanine.
4. Place riser to the ROC Module
slot. Have the mezzanine standoffs
snap in to the motherboard
4
Riser
mezzanine
4
5
5
11. Place the unit to the rack. Please refer to
Rail Kit Installation Guide on how to
mount the enclosure.
Caution: At least two people are
required to lift a fully populated
chassis
12. Install the populated drive trays into the
enclosure with the drives properly secured to the hard
drive trays.
5. Secure and tighten all screws.
IO Module compatible cards
Intel Dual SFP+ port 10GbE (AXX10GBNIAIOM)
Dual RJ45 Port, 10GBASE-T (AXX10GBNIAIOM)
Single Port FDR speed IB (AXX1FDRIBIOM)
Quad Port 1GbE (AXX4P1GBPWLIOM)
2. Make
sure that
the drive
goes
underneath
the hooks
ROC Module comp. cards
RMS25CB040
RMT3CB080
RMS25KB080
RMS25KB040
1. Push the tray by the
latch all the way into the
drive bay to ensure a
complete insertion
For further details, refer to S2600IP motherboard TPS and
the user’s guide for each IO card.
2. Secure the drive tray
installation by placing the
tray handle to the lock
position
Some cards require BBU. The enclosure
supports 6 BBUs for 6 RAID controllers.
Note the locations:
Two reside on the
back panel.
Four are placed
on a BBU bracket
(on top of the
ROC module).
13. Drive mapping incrementally goes from left to
right depending on the connection to the IO cards.
1
7. Install OS drive(s) as follows:
4. Install the SATA+power
cable to the disk.
Secure the disk and bracket
with 6-32 screws from the
outside of the chassis.
2. Install the
bracket on one
side of the disk
and secure with
M3 screws
Slot for secondary OS
drive is available.
Note the orientation of
the drives (the location
of the SATA and power
cables)
3. Place the other
side of the disk to
the guide pins
1. Release the OS
disk bracket by
removing the
screws securing it
14. Plug in the power cords to
the AC receptacles on the back of the unit
and secure it with the wire lock.
15. Press the power button on
the front of the unit after connecting a monitor
and input devices, and get ready for software
installation.
If you have any technical questions, please contact your authorized dealer before contacting us.
For more information please visit our website at www.echostreams.com
48