HPC-2820-ISSE
2U DP Xeon HPC system w/12*FBD,
8*SAS, Dual GbE
E3078
First Edition V1.00
February 2007
Contents
Notices.......................................................................................................... vi
Safety information...................................................................................... vii
About this guide........................................................................................ viii
Chapter 1: Product Introduction
1.1
1.2
1.3
1.4
1.5
1.6
System package contents............................................................... 2
System specifications..................................................................... 3
Front panel features......................................................................... 5
Rear panel features.......................................................................... 5
Internal features............................................................................... 6
LED information............................................................................... 7
1.6.1
Front panel LEDs................................................................ 7
1.6.2
System fan LED.................................................................. 8
1.6.3
Power supply LED.............................................................. 9
1.6.4
LAN port LEDs.................................................................... 9
Chapter 2: Hardware setup
2.1
2.2
2.3
2.4
2.5
2.6
ii
Chassis cover................................................................................... 2
2.1.1
Removing the front bezel.................................................... 2
2.1.2
Removing the top cover...................................................... 3
2.1.3
Installing the top cover........................................................ 5
2.1.4
Removing the air duct......................................................... 6
2.1.5
Installing the air duct........................................................... 7
Central Processing Unit (CPU)....................................................... 8
2.2.1
Installing a CPU.................................................................. 8
2.2.2
Installing the CPU heatsink............................................... 10
System memory..............................................................................11
2.3.1
Memory configurations.......................................................11
2.3.2
Memory mirroring and sparing technology........................ 13
2.3.3
Installing a DIMM.............................................................. 17
2.3.4
Removing a DIMM............................................................ 17
Hard disk drives............................................................................. 18
Expansion cards............................................................................ 20
2.5.1
Installing a full-length expansion card............................... 20
2.5.2
Installing a ZCR card (optional)........................................ 23
2.5.3
DDR2 SO-DIMM socket . ................................................. 25
2.5.4
Configuring an expansion card......................................... 25
2.5.5
Interrupt assignments....................................................... 25
Cable connections......................................................................... 26
2.6.1
Motherboard...................................................................... 27
Contents
2.7
2.6.2
SAS backplane................................................................. 28
2.6.3
Fan boards........................................................................ 29
Removable components................................................................ 30
2.7.1
Hot-swap mid-fans (80mm)............................................... 30
2.7.2
Power supply modules...................................................... 31
2.7.3
Slim optical and floppy drives........................................... 33
2.7.4
Front panel LED and switch board.................................... 34
2.7.5
SAS backplane................................................................. 35
2.7.6
System fan board............................................................. 35
2.7.7
Power supply cage............................................................ 37
2.7.8
LAN adapter (Optional)..................................................... 38
2.7.9
LAN cable......................................................................... 38
Chapter 3: Installation options
3.1
3.2
3.3
3.4
Rackmount rail kit items.................................................................. 2
Attaching the rails to the server..................................................... 3
Attaching the rack rails................................................................... 4
Rackmounting the server................................................................ 6
4.1
Motherboard layout.......................................................................... 2
4.1.1
Screw holes........................................................................ 2
4.1.2
Layout contents................................................................... 3
Support kits for the motherboard................................................... 4
Jumpers............................................................................................ 6
Switch.............................................................................................. 10
Connectors......................................................................................11
Chapter 4: Motherboard information
4.2
4.3
4.4
4.5
Chapter 5: BIOS setup
5.1
5.2
Managing and updating your BIOS................................................ 2
5.1.1
Creating a bootable floppy disk........................................... 2
5.1.2
Updating the BIOS using the Phoenix Phlash16 Utility....... 3
BIOS setup program........................................................................ 4
5.2.1
BIOS menu screen.............................................................. 5
5.2.2
Menu bar............................................................................. 5
5.2.3
Legend bar.......................................................................... 6
5.2.4
Menu items......................................................................... 6
5.2.5
Sub-menu items.................................................................. 6
5.2.6
Configuration fields............................................................. 6
5.2.7
Pop-up window................................................................... 7
5.2.8
General help....................................................................... 7
HPC-2820-ISSE User Manual
iii
Contents
5.3
5.4
5.5
5.6
5.7
5.8
Main menu........................................................................................ 8
5.3.1
System Date [Day xx/xx/xxxx]............................................. 8
5.3.2
System Time [xx:xx:xx]....................................................... 8
5.3.3
Floppy A [1.44M, 3½in.]...................................................... 8
5.3.4
IDE Configuration................................................................ 9
5.3.5
IDE Channel 0 Master/Slave..............................................11
5.3.6
SATA Port 1/2/3/4.............................................................. 12
5.3.7
System Information........................................................... 14
Advanced menu............................................................................. 16
5.4.1
Advanced Processor Options........................................... 16
5.4.2
Chipset Configuration....................................................... 19
5.4.3
PCI Configuration.............................................................. 22
5.4.4
ICH USB Control Sub-Menu............................................. 24
5.4.5
Peripheral Devices Configuration..................................... 25
5.4.6
ACPI Configuration........................................................... 27
5.4.7
Power On Configuration.................................................... 28
5.4.8
Hardware Monitor............................................................. 29
Server menu................................................................................... 32
5.5.1
Console Redirection.......................................................... 32
5.5.2
DMI Event Logging........................................................... 34
Security menu................................................................................ 35
Boot menu...................................................................................... 37
5.7.1
Boot Device Priority.......................................................... 37
5.7.2
Boot Features................................................................... 38
Exit menu........................................................................................ 39
Chapter 6: RAID configuration
6.1
6.2
iv
Setting up RAID................................................................................ 2
6.1.1
RAID definitions.................................................................. 2
6.1.2
Installing hard disk drives.................................................... 3
6.1.3
Setting the RAID item in BIOS............................................ 3
6.1.4
RAID configuration utilities.................................................. 3
LSI Logic MPT Setup Utility............................................................ 4
6.2.1
Integrated Mirroring............................................................. 4
6.2.2
Integrated Mirroring Enhanced........................................... 8
6.2.3
Integrated Striping (IS) volume......................................... 10
6.2.4
Managing Arrays............................................................... 13
Viewing SAS topology....................................................... 18
6.2.5
6.2.6
Global Properties.............................................................. 20
Contents
Chapter 7: Driver installation
7.1
7.2
7.3
7.4
RAID driver installation................................................................... 2
7.1.1
Creating a RAID driver disk................................................ 2
7.1.2
Installing the RAID controller driver.................................... 3
Intel chipset software installation................................................ 12
LAN driver installation................................................................... 15
7.3.1
Windows 2000/Server 2003.............................................. 15
7.3.2
Red Hat/SuSE Linux......................................................... 20
VGA driver installation.................................................................. 21
7.4.1
Windows® 2000/Server 2003............................................ 21
Appendix: References
A.1
A.2
Power supply.................................................................................... 2
A.1.1 General description............................................................. 2
A.1.2 Specifications...................................................................... 3
Troubleshooting............................................................................... 4
HPC-2820-ISSE User Manual
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’
s instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
•
Increase the separation between the equipment and receiver.
Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of shielded cables for connection of the monitor to the
graphics card is required to assure compliance with FCC regulations. Changes
or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
vi
Safety information
Electrical safety
•
•
•
•
Before installing or removing signal cables, ensure that the power cables for
the system unit and all attached devices are unplugged.
To prevent electrical shock hazard, disconnect the power cable from the
electrical outlet before relocating the system.
When adding or removing any additional devices to or from the system, ensure
that the power cables for the devices are unplugged before the signal cables
are connected. If possible, disconnect all power cables from the existing
system before you add a device.
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your dealer.
Operation safety
•
•
•
•
•
Any mechanical operation on this server must be conducted by certified or
experienced engineers.
Before operating the server, carefully read all the manuals included with the
server package.
Before using the server, make sure all cables are correctly connected and the
power cables are not damaged. If any damage is detected, contact your dealer
as soon as possible.
To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
Avoid dust, humidity, and temperature extremes. Place the server on a stable
surface.
This product is equipped with a three-wire power cable and plug for the user’s
safety. Use the power cable with a properly grounded electrical outlet to avoid
electrical shock.
Lithium-Ion Battery Warning
CAUTION! Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
CD-ROM Drive Safety Warning
CLASS 1 LASER PRODUCT
Heavy System
CAUTION! This server system is heavy. Ask for assistance when moving or
carrying the system.
HPC-2820-ISSE User Manual
vii
About this guide
Audience
This user guide is intended for system integrators and experienced users with at
least basic knowledge of configuring a server.
Contents
This guide contains the following parts:
1.
viii
Chapter 1: Product Introduction
This chapter describes the general features of the barebone server, including
sections on the front panel and rear panel specifications.
2.
Chapter 2: Hardware setup
3.
Chapter 3: Installation options
4.
Chapter 4: Motherboard information
5.
Chapter 5: BIOS setup
6.
Chapter 6: RAID configuration
7
Chapter 7: Driver installation
8.
Appendix: References
This chapter lists the hardware setup procedures that you have to perform
when installing or removing system components.
This chapter describes how to prepare the barebone server for rack
mounting.
This chapter gives information about the motherboard that comes with the
server. This chapter includes the motherboard layout, jumper settings, and
connector locations.
This chapter tells how to change the system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
This chapter tells how to change system settings through the BIOS Setup
menus. Detailed descriptions of the BIOS parameters are also provided.
This chapter provides instructions for installing the necessary drivers for
different system components.
This appendix includes additional information that you may refer to when
configuring your barebone server.
Conventions
To make sure that you perform certain tasks properly, take note of the following
symbols used throughout this manual.
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a task.
NOTE: Tips and information to aid in completing a task.
HPC-2820-ISSE User Manual
ix
CHAPTER
1
Product Introduction
1.1
System package contents
Check your system package for the following items.
Chassis
Motherboard
Components
2U rackmount chassis
HPC-2820-ISSE motherboard
1 x 750W redundant power supply module, 115V~230V
1 x power supply bay cover
Slim optical drive|
Slim floppy disk drive
Chassis fan
HDD fan
Hot-swap SAS HDD trays
SAS backplanes
1 x Dummy CPU heatsink
AC power cable
Cables
Accessories
System cables
Rackmount rail kit
HPC-2820-ISSE user guide
HPC-2820-ISSE support CD (includes ASWM*)
Chassis ears (left, right)
Optional items
One bag of screws
CPU heatsink
LAN adapter
Front bezel
SAS ZCR package
Second redundant power supply module
If any of the above items is damaged or missing, contact your retailer.
1-
Chapter 1: Product introduction
1.2
System specifications
The HPC-2820-ISSE is a 2U barebone server system. The server supports dual
Intel® 5100 series CPU with EM64T technology, plus other latest technologies
through the chipsets onboard.
Chassis
2U rackmount chassis
Chipset
MCH : Intel® 5000P
ICH : Intel® 6321ESB
I/O Bridge : Intel 6702 PXH (on the riser card cage)
Motherboard
CPU
Front Side Bus
Memory
LAN
Discrete graphics
Expansion slots
Storage
HPC-2820-ISSE
Dual LGA771 sockets for Intel® Xeon™ Dual Core
processors 5000/5100/5300 Series
Supports Intel® Extended Memory 64Technology (EM64T)
1333/1066/667 MHz
Quadri-channel memory architecture
12 x 240-pin FB-DIMM sockets support registered ECC
fully buffered DDR2-533/DDR2-667 memory modules
with Advanced Memory Buffer (AMB chip)
Supports 256 MB up to 48 GB system memory
Intel® 82563 Gigabit Network Connection (Dual-port)
- Supports Intel® I/O Acceleration Technology (IOAT)
ATI® ES1000 PCI display controller
- Supports 32 MB display memory
1 x PCI Express™ x8 slot (on the riser card cage)
2 x PCI-X 133/100 MHz slot (on the riser card cage; only 1
PCI-X available if you install an optional ZCR.)
1 x DDR2 SO-DIMM socket for server management board
3 series
LSI1068 PCI-X SAS controller supports:
- 2 x Serial Attached SCSI (SAS) channels
(each channel supports 4 HDDs, total 8 HDDs) with
RAID 0, RAID 1, and RAID 1E configuration
- Zero-Channel RAID (optional)
(continued on the next page)
HPC-2820-ISSE User Manual
1-
Front panel
Rear panel
Management
Hardware monitors
Power supply
Dimensions
8 x 3.5-inch hot-swappable HDD bays
1 x slim optical drive
1 x slim 1.44MB floppy drive)
2 x USB 2.0 ports
Power switch
Reset switch
Location switch
Power, HDD access, location, message, LAN 1/2 LED
HDD LEDs: Status, activity
1 x PS/2 keyboard port
1 x PS/2 mouse port
1 x Serial port
1 x VGA port
2 x USB 2.0 ports
2 x RJ-45 ports (with LEDs)
1 x Location switch
1 x Location LED
Server Web-based Management
Voltage, temperature, and fan speed monitoring
Automatic System Restart (ASR) feature
1 + 1 750W redundant power supply, 115V~230V,
50Hz~60Hz
732.5mm (l) x 448mm (w) x 87.7mm (h)
The standard server system ships with one redundant power supply module.
Contact your retailer if you need a second one.
Refer to “Chapter 4 Motherboard information” for details on the internal
connectors.
1-
Chapter 1: Product introduction
1.3
Front panel features
The barebone server displays a simple yet stylish front panel with easily accessible
features. The power and reset buttons, LED indicators, location switch, slim optical
and floppy drives, and two USB ports are located on the front panel.
Reset button
Location switch
Front panel LEDs
Hot-swappable HDD bays
USB 2.0 ports
1.4
Slim optical drive
Slim floppy drive
Power button
Rear panel features
The rear panel includes the expansion slots, LAN, VGA, and I/O ports, fans, and
the system power sockets.
Redundant power
supply modules
Rear fan bays
Expansion slots
Location LED
Location switch
Gigabit LAN2 port
VGA port
Gigabit LAN1 port
Serial port
USB 2.0 ports
PS/2 keyboard port
PS/2 mouse port
AC power sockets
When disconnecting LAN cables, you need to remove the rear fan cage. Refer
to section “2.7 Removable components” for instructions on removing the fan
cage.
HPC-2820-ISSE User Manual
1-
1.5
Internal features
The barebone system includes the basic components as shown.
1
2
3
3
4
5
6
7
Riser card cage
8
9
1.
2.
3.
4.
5.
2 x rear fan bays
(for future upgrade)
PCI-E slots
(underneath the riser card cage)
12 x FB-DIMM sockets
Power supply module
CPU2 socket
10
11
6.
CPU1 socket
8.
SAS backplane
7.
9.
7 x system fans
3 x HDD
10. Top: Slim optical drive
Mid: Slim floppy drive
Bottom: 2 x HDD
11. 3 x HDD
The air duct lies on top of the motherboard components. Remove the air duct to
access the components. Refer to section “2.1.4 Removing and installing the air
duct” for instructions.
1-
Chapter 1: Product introduction
1.6
LED information
1.6.1
Front panel LEDs
Power LED
Location LED
Message LED
Storage Access LED
LAN1 LED
LAN2 LED
LED
Icon
Power LED
Storage Access LED
Message LED
Display status
ON
OFF
Blinking
OFF
Blinking
Location LED
OFF
ON
LAN1/2 LEDs
OFF
Blinking
ON
Description
System power ON
No activity
Read/write data into the HDD
System is normal; no incoming event
ASWM indicates a HW monitor event
Normal status
Location switch is pressed
(Press the location switch again to turn off)
No LAN connection
LAN is transmitting or receiving data
LAN connection is present
The location switch and LED are for service purposes. When the system fails
or is shut down, the server administrator can press either the front or the
rear location switch to identify the location of the specific 2U system in a rack
cabinet.
HPC-2820-ISSE User Manual
1-
1.6.2
System fan LED
Each system fan has an LED to indicate the fan status.
LED
LED
LED
Color
Green
Orange
Description
Fan is in normal operation
Fan is faulty
This function only works under OS and the system has installed ASWM
Software.
1-
Chapter 1: Product introduction
1.6.3
Power supply LED
Each system fan has an LED to indicate the fan status.
LED
LED color Display status
Green
Blinking
Green
On
Orange
On
Off
Off
1.6.4
Description
Power off and in standby mode
The power supply module is in normal operation
One of the two power modules is disconnected from the power outlet
or is defective
Both power supply modules are disconnected from the power outlet
or are defective
LAN port LEDs
SPEED LED
ACT/LINK LED
ACT/LINK LED
Status
Description
OFF
No link
GREEN
Linked
BLINKING
Data activity
HPC-2820-ISSE User Manual
SPEED LED
Status
Description
OFF
10 Mbps connection
ORANGE
100 Mbps connection
GREEN
1 Gbps connection
1-
1-10
Chapter 1: Product introduction
CHAPTER
2
Hardware Setup
1-
2.1
Chassis cover
The chassis features a “screwless design” that allows convenient assembly and
disassembly.
•
•
Remove the front bezel to access the hot-swap HDDs, optical drive, and
floppy drive.
Remove the chassis cover to access the internal components or if you want
to install system devices.
2.1.1
Removing the front bezel
To remove the front bezel:
1.
Hold the sides of the front bezel,
then slightly press the middle part to
disengage it from the front panel.
Press here to release
2.
Pull the bezel from the front panel.
The front bezel is purchased separately.
2-
Chapter 2: Hardware setup
2.1.2
Removing the top cover
Front half
To remove the front half of the top cover:
1.
Push the two sliding locks on the
top cover to release.
2.
With both hands, flip up the front
corners of the top cover, then lift.
The front corners of the cover
have dents that match those on
the chassis. These dents provide a
holding mechanism and keeps the
cover in place even when the sliding
locks are released.
Matching dents
If you wish to access the hot-swappable system fans, backplanes, optical drive,
and floppy disk drive, just remove the front half of the top cover.
HPC-2820-ISSE
2-
Rear half
You need to remove the front half of the top cover before you can remove the
rear half of the top cover. Refer to section “2.1.2 Removing the top cover (front
half)” for instructions.
To remove the rear half of the top cover:
1.
Loosen the thumbscrew that
secures the top cover on the rear
part of the chassis.
Thumbscrew
2. Remove the screw on the rear half
of the cover.
3. Firmly hold the rear half of the
top cover, then remove it from the
chassis.
2-
The barebone server without the top
cover is shown on the right.
Chapter 2: Hardware setup
2.1.3
Installing the top cover
To install the top cover:
1.
2.
Place the rear half of the top cover
over the chassis as shown, and
align the mid-hooks with the notches
on the sides.
Slide the cover toward the front
panel until the mid-hooks are
locked into the notches.
3.
Flip down the front half part of the
top cover.
4.
Push the sliding locks toward the
front edge to secure the front half of
the top cover in place.
5.
Tighten the thumbscrew on the rear
corner of the cover to completely
secure the top cover.
Thumbscrew
6. Replace the screw on the rear half
of the cover.
HPC-2820-ISSE
2-
2.1.4
Removing the air duct
To remove the air duct:
1.
Carefully route the cables that may
interfere when removing the air duct.
2.
Loosen the two screws that fasten
the air duct.
3.
Hold the rear part of the air duct
and press it for about a fraction of
an inch, just enough to tilt the front
end. When tilted, carefully pull the
air duct upward to release it from the
chassis.
Be careful not to pull off or break
any cables while removing the air
duct.
2-
Chapter 2: Hardware setup
2.1.5
Installing the air duct
To install the air duct:
1.
Take note of the parts of the air duct that should match specific locations
inside the chassis.
air duct screw holes
air duct screw holes
2.
3.
4.
Flat rubber pad should match the top of the
two heatsinks
Position the air duct inside the
chassis aligning with the two air duct
screw holes.
Check the rubber pads underneath
the air duct and ensure that they are
in place; otherwise, the air duct will
not fit properly.
Fit the other end of the air duct
making sure that no power cable is
strayed under it.
Be careful not to pull off or break any cables while installing the air duct.
5.
Fasten the air duct with screws.
6.
When the air duct is in place, arrange the power cable cluster to fit the space
beside the air duct.
HPC-2820-ISSE
2-
2.2
Central Processing Unit (CPU)
The motherboard comes with two surface mount 771-pin socket and designed for
the Intel® Xeon™ processors.
Note in the illustration that the CPU has a gold triangular mark on one corner. This
mark indicates the processor Pin 1 that should match a specific corner of the CPU
socket.
®
CPU1
CPU2
CPU LGA771
2.2.1
Installing a CPU
•
The motherboard supports either one or two CPUs. If you are installing only
one CPU, you MUST install it in CPU socket 1.
•
Remove the dummy heatsink if you want to install the second CPU.
To install a CPU:
1.
Locate the CPU socket on the motherboard.
Incorrect installation of the CPU into the socket may bend the pins and severely
damage the CPU!
2.
Press the load lever with your thumb (A), then move it to the left (B) until it is
released from the retention tab.
Retention tab
Load lever
A
PnP cap
B
This side of the socket box
should face you.
To prevent damage to the socket pins, do not remove the PnP cap unless you
are installing a CPU.
2-
Chapter 2: Hardware setup
3.
Lift the load lever in the direction of
the arrow to a 135º angle.
4.
Lift the load plate with your
thumb and forefinger to a 100º
angle (A), then push the PnP
cap from the load plate window
to remove (B).
B
A
Load plate
5.
Position the CPU over
the socket, making sure
that the gold triangle
is on the bottom-left
corner of the socket.
The socket alignment
key should fit into the
CPU notch.
Alignment key
Gold triangle mark
6.
Close the load plate (A), then
push the load lever (B) until it
snaps into the retention tab.
A
B
The CPU fits in only one correct orientation. DO NOT force the CPU into the
socket to prevent bending the connectors on the socket and damaging the CPU!
HPC-2820-ISSE
2-
2.2.2
Installing the CPU heatsink
According to your purchase, the sever system may ship with different CPU and
heatsink combination:
Two CPUs
One CPU
One heatsink
One dummy heatsink
(on the CPU 2 socket)
Two heatsinks
No CPU
One dummy heatsink
(on the CPU 2 socket)
You must install the CPU heatsink(s) after installing the CPU(s). If your model is
not included heatsinks, you can either purchase heatsink separately from retailer or
purchase an Intel 2U box CPU.
To install the CPU heatsink:
2-10
1.
Carefully align the heatsink
screws to the screw holes on the
motherboard.
2.
Use a Phillips (cross) screwdriver
to fasten screws, two at a time in a
diagonal sequence.
3.
For the second CPU heatsink installation, repeat the previous steps.
•
If there is a dummy heatsink, unscrew and remove it first before installing
the second real heatsink.
•
DO NOT remove the dummy heatsink if there is only one CPU installed.
The CPU 1 may be overheated and damaged with the removal of the
dummy heatsink.
Chapter 2: Hardware setup
2.3
System memory
The motherboard comes with 12 fully-buffered DIMM (FB-DIMM) sockets to
support 240-pin FB-DIMM modules. An FB-DIMM module has a different pin-out
from DDR2 DIMMs so you cannot install DDR2 DIMMs on an FB-DIMM socket.
Note that an FB-DIMM socket has an Advanced Memory Buffer (AMB) chip that
allows memory-to-CPU connection at gigabit speed.
The figure illustrates the location of the FB-DIMM sockets:
128 Pins
112 Pins
FB-DIMM_12
FB-DIMM_11
FB-DIMM_10
®
FB-DIMM_02
FB-DIMM_01
FB-DIMM_00
FB-DIMM_20
FB-DIMM_21
FB-DIMM_22
FB-DIMM_30
FB-DIMM_31
240-pin FB-DIMM sockets
2.3.1
FB-DIMM_32
Memory configurations
You may install 512 MB, 1 GB, 2 GB, and 4 GB registered ECC FB‑DIMMs into the
DIMM sockets.
•
For optimum compatibility, we recommend that you obtain memory
modules from the same vendor.
•
This motherboard does not support memory modules made up of 128 Mb
chips or double-rank x16 memory modules.
•
If you are installing only one memory module, install into the white socket
labeled DIMM_00. Installing into any other socket will not work.
HPC-2820-ISSE User Manual
2-11
Rank population
Slot 2
Slot 0
Slot 1
Slot 2
DIMM-12
DIMM_10
Slot 1
Ch:0
DIMM_11
DIMM_02
Slot 0
DIMM_01
Ch:2
DIMM_00
Slot 0
Slot 2
Slot 1
Slot 0
DIMM_20
DIMM_22
Slot 1
DIMM_21
DIMM_30
Slot 2
DIMM_31
DIMM_32
Ch:3
MCH
Ch:1
DIMM installation reference table
No. of
DIMMs
Slot/s to use
Memory
architecture
1
DIMM_00
4
DIMM_00, DIMM_10, DIMM_20, DIMM_30
2
8
12
Single channel
DIMM_00, DIMM_10
DIMM_00, DIMM_10, DIMM_20, DIMM_30
DIMM_01, DIMM_11, DIMM_21, DIMM_31
DIMM_00, DIMM_01, DIMM_02
DIMM_10, DIMM_11, DIMM_12
DIMM_20, DIMM_21, DIMM_22
DIMM_30, DIMM_31, DIMM_32
Dual channel
Quadri channel
DIMMs in pair means two DIMMs with the same configuration.
2-12
Chapter 2: Hardware setup
2.3.2
Memory mirroring and sparing technology
The Intel® 5000P chipset supports the memory mirroring and sparing technology.
Refer to the below sections:
Memory Mirroring
When enabling memory mirroring function in the BIOS setting (refer to section
“5.4.2 Chipset Configuration” and configure the option “Memory Branch
Mode” as Mirror), Branch 1 contains a replicate copy of the data in Branch 0. The
DIMMs must cover the same slot position on both branches. DIMMs that cover
a slot position must be identical with respect to size, speed, and organization.
DIMMs within a slot position must match each other, but are not required to match
adjacent slot positions.
The total memories size will be the half of all installed memories.
The below memory configurations were required to operate in mirrored mode.
Configuration 1 (Mirroring): Four memories population
DIMMs are installed in the following slots: DIMM_00, DIMM_10, DIMM_20, and
DIMM_30.
Branch 1
(Mirror)
Slot 2
Slot 0
Slot 1
Slot 2
DIMM-12
DIMM_10
Slot 1
Ch:0
DIMM_11
DIMM_02
Slot 0
HPC-2820-ISSE User Manual
DIMM_01
Ch:2
MCH
DIMM_00
Slot 0
Slot 2
Slot 1
Slot 0
DIMM_20
DIMM_22
Slot 1
DIMM_21
DIMM_30
Slot 2
DIMM_31
DIMM_32
Ch:3
Branch 0
Ch:1
2-13
Configuration 2 (Mirroring) : Eight memories population
DIMMs are installed in the following slots: DIMM_00, DIMM_01, DIMM_10,
DIMM_11, DIMM_20, DIMM_21, DIMM_30, and DIMM_31.
Branch 1
(Mirror)
Slot 2
Slot 0
Slot 1
Slot 2
DIMM-12
DIMM_10
Slot 1
Ch:0
DIMM_11
DIMM_02
Slot 0
Ch:2
DIMM_01
MCH
DIMM_00
Slot 0
Slot 2
Slot 1
Slot 0
DIMM_20
DIMM_22
Slot 1
DIMM_21
DIMM_30
Slot 2
DIMM_31
DIMM_32
Ch:3
Branch 0
Ch:1
Configuration 3 (Mirroring) : Twelve memories population
DIMMs are installed in all slots: DIMM_00, DIMM_01, DIMM_02, DIMM_10,
DIMM_11, DIMM_12, DIMM_20, DIMM_21, DIMM_22, DIMM_30, DIMM_31,
and DIMM_32.
Branch 1
(Mirror)
Slot 0
Slot 2
Slot 2
Slot 1
DIMM_10
Slot 1
DIMM-12
DIMM_02
Ch:0
DIMM_11
DIMM_01
Slot 0
Ch:2
MCH
DIMM_00
Slot 0
Slot 2
Slot 1
Slot 0
DIMM_20
DIMM_22
Slot 1
2-14
DIMM_21
DIMM_30
Slot 2
DIMM_31
DIMM_32
Ch:3
Branch 0
Ch:1
Chapter 2: Hardware setup
Memory Sparing
At configuration time, a DIMM rank is set aside to replace a defective DIMM rank.
When the error rate for a failing DIMM rank reaches a pre-determined threshold,
the memory sparing function will issue an interrupt and initiate a spare copy. At the
completion of the copy, the failing DIMM rank is disabled and the “spared” DIMM
rank will be used in its place. Refer to section “5.4.2 Chipset Configuration and
configure the options of “Branch 0 Rank Sparing” or “Branch 1 Rank Sparing” to
enable the memory sparing functions. The default BIOS setting is disabled.
•
Each branch contains its own sparing engine and can be enabled or
disabled separately.
•
This motherboard does not support rank sparing across branches.
•
This motherboard does not support rank sparing when in mirror mode.
•
The DIMM rank with the largest size will be assigned as spare rank. Data
can only be copied from a smaller sized rank to a larger sized one.
•
A DIMM can contain only one or two ranks. To support sparing function, a
DIMM channel should contain at least two ranks.
•
When sparing function is enabled, the usable memory size will reduce the
size of the spare ranks.
The following tables show memory configurations with Memory Sparing function in
Branch 0.
One DIMM per channel (two ranks)
Channel 0
Branch0
Sparing
Memory space
Total Memory
HPC-2820-ISSE User Manual
Channel 1
DIMM_00.
(1024MB*2 Ranks)
Rank 0
Rank 1
(1024 MB)
(1024 MB)
•
DIMM_10.
(1024MB*2 Ranks)
Rank 0
Rank 1
(1024 MB)
(1024 MB)
•
1024 MB
1024 MB
2048 MB
2-15
Two DIMMs per channel
Channel 0
Sparing
Branch0
Memory space
Sparing
Channel 1
DIMM_00.
(512MB*2 Ranks)
Rank 0
Rank 1
(512 MB)
(512 MB)
DIMM_10.
(512MB*2 Ranks)
Rank 0
Rank 1
(512 MB)
(512 MB)
1024 MB
1024 MB
DIMM_01.
(1024MB*2 Ranks)
Rank 0
(1024 MB)
Memory space
Rank 1
(1024 MB)
•
DIMM_11.
(1024MB*2 Ranks)
Rank 0
(1024 MB)
1024 MB
Total Memory
Rank 1
(1024 MB)
•
1024 MB
4096 MB
Three DIMMs per channel
Channel 0
Sparing
Memory space
Branch0
Sparing
Memory space
Sparing
Memory space
Total Memory
2-16
Channel 1
DIMM_00.
(512MB*2 Ranks)
Rank 0
Rank 1
(512 MB)
(512 MB)
DIMM_10.
(512MB*2 Ranks)
Rank 0
Rank 1
(512 MB)
(512 MB)
1024 MB
1024 MB
DIMM_01.
(1024MB*2 Ranks)
Rank 0
(1024 MB)
Rank 1
(1024 MB)
1024 MB
DIMM_02.
(2048MB*2 Ranks)
Rank 0
Rank 1
(2048 MB) (2048 MB)
DIMM_11.
(1024MB*2 Ranks)
Rank 0
(1024 MB)
Rank 1
(1024 MB)
1024 MB
DIMM_12.
(2048MB*2 Ranks)
Rank 0
Rank 1
(2048 MB)
(2048 MB)
•
•
2048 MB
2048 MB
10240 MB
Chapter 2: Hardware setup
2.3.3
Installing a DIMM
Make sure to unplug the power supply before adding or removing DIMMs or
other system components. Failure to do so may cause severe damage to both
the motherboard and the components.
To install a DIMM:
1.
2.
3.
Unlock a DIMM socket by pressing
the retaining clips outward.
Align a DIMM on the socket
such that the notch on the DIMM
matches the break on the socket.
Firmly insert the DIMM into the
socket until the retaining clips
snap back in place and the DIMM
is properly seated.
2.3.4
2
1
A FB-DIMM is keyed with a notch so that it fits in only one direction. Do not
force a DIMM into a socket to avoid damaging the DIMM.
•
Thesockets do not support DDR/DDR2 DIMMs. DO NOT install DDR/DDR2
DIMMs to the FB-DIMM sockets.
Removing a DIMM
2
1
Simultaneously press the retaining
clips outward to unlock the DIMM.
Support the DIMM lightly with
your fingers when pressing
the retaining clips. The DIMM
might get damaged when it
flips out with extra force.
2.
FB-DIMM notch
•
To remove a DIMM:
1.
1
3
1
Remove the DIMM from the socket.
HPC-2820-ISSE User Manual
2-17
2.4
Hard disk drives
To install a hard disk drive:
1.
2.
2-18
Open the front bezel to access the
hot-swap drive trays.
Release a drive tray by pushing the
spring lock to the right, then pulling
the tray lever outward. The drive
tray ejects slightly after you pull out
the lever.
3.
Firmly hold the tray lever and pull
the drive tray out of the bay.
4.
An empty drive tray includes a metal
bracket for support. Use a Phillips
(cross) screwdriver to remove the
bracket if you wish to install a hard
disk in the drive tray.
Metal bracket
Chapter 2: Hardware setup
5.
Place a hard disk drive into the drive
tray, and secure it with four screws
(two on each side).
6.
Carefully insert drive tray and push
it all the way to the depth of the bay
until just a small fraction of the tray
edge protrudes.
7.
Push the tray lever until it clicks, and
secures the drive tray in place. The
drive tray is correctly placed when
its front edge aligns with the bay
edge.
HPC-2820-ISSE User Manual
2-19
2.5
Expansion cards
The system motherboard comes with one PCI-E expansion slots installed with
the Riser cage to support three expansion cards. A ZCR slot is also available for
installation of a Zero Channel RAID card.
PCI-E slot
PCI-E x8 slot
PCI-X slot
PCI-X slot
(will not be available with
an optional ZCR installed)
I/O Bridge: 6702 PXH
2.5.1
Installing a full-length expansion card
The full-length expansion cards are inside the PCI cage. If you wish to install
full-length expansion cards, you need to remove the PCI cage from the chassis.
To install a full-length expansion card:
1.
Firmly hold and lift the cage as
shown to completely detach it from
the chassis.
2.
Place the cage on a flat stable
surface with the slot facing up, and
prepare the card that you want to
install.
Internal view of PCI cage
2-20
Chapter 2: Hardware setup
3.
Unscrew the metal cover opposite
the PCI-X slot that you want to use.
4.
The card golden connectors should
match the notches on the slot.
Then, firmly push down the card
until it is completely seated on the
slot.
5.
6.
Secure the card bracket with a
screw.
Connect power or signal cable(s) to
the card, if applicable.
Repeat steps 3 to 6 if you wish to install other PCI-X cards.
7.
Before re-installing the PCI cage
into the chassis, check that all
cables on the PCI cage bay are
properly connected and routed.
HPC-2820-ISSE User Manual
Cables on the PCI cage bay
2-21
8.
Take note of the two pegs on the
Riser cage bay. These pegs should
match the holes on the cage to
make sure it fits in place.
PCI cage pegs
9.
Position the Riser cage into the bay
making sure that the pegs go into
the holes on the front of the cage,
and the dents on the rear part match
those on the chassis.
10. Match and push the cage card
connector into the PCI-E slot until the
PCI cage fits in place.
11. Ensure that the golden connectors of the riser cage card completely fit the
slot. If properly installed, the top of the PCI cage aligns with the top edge of
the rear panel.
2-22
Chapter 2: Hardware setup
2.5.2
Installing a ZCR card (optional)
After installing a riser card, you can install a ZCR card to your motherboard that
supports RAID 0, RAID 1, RAID 1-E and RAID 5 configuration. The optional ZCR
package includes one LSI8300XCP ZCR card, two support brackets, and one riser
card.
To install a ZCR card:
Screw the support bracket to the ZCR card.
2.
Install the ZCR card to the riser card.
3.
Remove one screw that fasten the motherboard to the chassis.
DSBF-D12/2U/SAS
1.
HPC-2820-ISSE User Manual
2-23
2-24
4.
After installing the riser card with a
ZCR card, fasten the screw back..
5.
Align the other support bracket for
the ZCR card to the screw holes on
the chassis.
6.
Secure the support bracket for the
ZCR card with screws.
Chapter 2: Hardware setup
2.5.3
DDR2 SO-DIMM socket
The DDR2 SO-DIMM socket on the
motherboard support an optional Server
Management Board.
DDR2 SO-DIMM socket
2.5.4
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software settings.
1.
2.
3.
Turn on the system and change the necessary BIOS settings, if any. See
Chapter 5 for information on BIOS setup.
Assign an IRQ to the card. Refer to the tables below.
Install the software drivers for the expansion card.
When using PCI cards on shared slots, ensure that the drivers support “Share
IRQ” or that the cards do not need IRQ assignments. Otherwise, conflicts will
arise between the two PCI groups, making the system unstable and the card
inoperable.
2.5.5
IRQ
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Interrupt assignments
Priority
1
2
—
11
12
13
14
15
3
4
5
6
7
8
9
10
Standard function
System timer
Keyboard Controller
Re-direct to IRQ#9
Communications Port (COM2)*
Communications Port (COM1)*
IRQ holder for PCI steering*
Floppy Disk Controller
Printer Port (LPT1)*
System CMOS/Real Time Clock
IRQ holder for PCI steering*
IRQ holder for PCI steering*
IRQ holder for PCI steering*
PS/2 Compatible Mouse Port*
Numeric Data Processor
Primary IDE Channel
Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
HPC-2820-ISSE User Manual
2-25
2.6
Cable connections
•
The bundled system cables are pre-connected before shipment. You do
not need to disconnect these cables unless you will remove pre-installed
components to install additional devices.
•
Refer to this section when reconnecting cables to ensure correct cable
connections.
12
Rear panel
1
13
11
2
9
4
3
5
6
7
Front panel
8
10
Pre-connected system cables
1.
2.
3.
4.
5.
6.
7.
8.
24-pin/8-pin/4pin power connectors (from power supply to MB)
Floppy drive connector (from MB to floppy drive)
PANEL connectors (from MB to front panel)
Chassis intrusion connector (from MB to chassis)
LAN LED connector and Locator LED connector/switch (from MB to front panel)
2 x SAS connectors (from MB to SAS backplane)
Primary IDE (from MB to optical drive)
Mid-fan power connector (from power supply to mid-fan board)
SAS board connectors (from the SAS backplane to MB and power supply; one from the
Mid-fan board to SAS backplane)
9. Front USB connectors (from MB to front panel)
10. Locator LED connector/switch (from front panel to rear panel Locator LED/switch)
11. CPU_FAN1 connector (from MB to mid-fan board)
12. Power supply SMBus connector
13. Backplane SMBus connector
2-26
Chapter 2: Hardware setup
2.6.1
Motherboard
5-pin PSUSMB1 cable from power supply
24-pin power cable
4-pin power cable
33cm (13in)
KBPWR1
PS/2
ATXPWR1
PSUSMB1
USBPW12
T: Mouse
B: Keyboard
8-pin power cable
CPU_FAN1
ATX12V1
ATX12V2
DDR FB-DIMM_12 (64/72 bit, 240-pin module)
USB1
USB2
COM1
REAR_FAN1
REAR_FAN2
cable
3-pin CPU fan
control cable
DDR FB-DIMM_11 (64/72 bit, 240-pin module)
FBD_FAN1
DDR FB-DIMM_10 (64/72 bit, 240-pin module)
REAR_FAN1
DDR FB-DIMM_01 (64/72 bit, 240-pin module)
CPU1
DDR FB-DIMM_02 (64/72 bit, 240-pin module)
REAR_FAN2
FBD_FAN2
RJ-45
(LAN1)
Intel®
5000P
CPU2
RJ-45
(LAN2)
DDR FB-DIMM_21 (64/72 bit, 240-pin module)
ASMB3
DDR FB-DIMM_32 (64/72 bit, 240-pin module)
FRNT_FAN4
DDR FB-DIMM_31 (64/72 bit, 240-pin module)
FRNT_FAN2
DDR FB-DIMM_30 (64/72 bit, 240-pin module)
82563EB
FRNT_FAN1
DDR FB-DIMM_22 (64/72 bit, 240-pin module)
CPU_FAN2
Rear panel
DDR FB-DIMM_20 (64/72 bit, 240-pin module)
30.5cm (12in)
DSBF-D12/2U/SAS
VGA1
DDR FB-DIMM_00 (64/72 bit, 240-pin module)
PRI_IDE1
ATI
ES1000
TPM1
SATA1
SATA2
PCIE1EXT1
AMI
8Mb
FWH
RECOVERY1
DIP_SW1
Super
I/O
CLRTC1
CR2032 3V
Lithium Cell
CMOS Power
SAS_EN1
LPC1
LAN_BW1
LSI
SAS1068
LPT1
COM2
®
Intel
6321ESB
SAS2
SAS1
BUZZER1
VGA_EN1
USBPW34
SB_PWR1
HDLED1
SATA3
SATA4
PCIE1
SATA5
SATA6
LAN_EN1
SLIM_PCIX5
SGPIO1
SASLED1
FLOPPY1
USB34
AUX_PANEL1
FRNT_FAN3
PANEL1
BPSMB1
2-pin chassis intrusion
cable to chassis;
2~4-pin LAN LED and
Locator LED/switch to
front panel
20-pin PANEL
cable to front
panel
Floppy drive
cable
SAS cables to SAS
Backplane ports
USB cable to front
panel board
IDE cable to
optical drive
Connect the CPU fan control cable to the Mid-fan board, otherwise the CPU
fans will always run at full speed.
HPC-2820-ISSE User Manual
2-27
2.6.2
SAS backplane
View from front panel
Hot-swap SAS HDD connectors
SAS HDD connectors disposition
ID0
ID1
ID2
ID5
ID6
ID7
ID3
ID4
View from rear panel
FBSMBus connector
Mini SAS connectors
J2 jumper
SMBus connector
ESB2 SGPIO connector
Power connector
J2 jumper configuration
2
1
4
3
6
5
Onboard SAS SGPIO
(Default)
2-28
Chapter 2: Hardware setup
2.6.3
Fan boards
Main mid-fan boards (FANBPC-E2-AR21)
(located underneath the 7 hot-swap fans)
7
6
5
4
3
2
1
Connect the mid-fan board (FANBPC-E2-AR21)
Mid-fan board
(FANBPC-E2-AR21)
P3 plug from power supply
3-pin connects to CPU_FAN1
SMBus cable from SAS backplane
To main fan board
(FANBPC-E2-AR21)
HPC-2820-ISSE User Manual
2-29
2.7
Removable components
You may need to remove previously installed system components when installing
or removing system devices, or when you need to replace defective components.
This section tells how to remove the following components:
1. Hot-swap mid-fans
6. System fan board
3. Optical drive/floppy drive 8. LAN adaper (Optional)
2. Power supply modules
4. Front panel LED/switch board
5. SAS backplane
2.7.1
7. Power supply cage
9. LAN cable
Hot-swap mid-fans (80mm)
The fan LED lights up green in normal operation. If the LED color turns orange, the
fan is faulty and should be replaced.
To remove an 80mm hot-swap fan:
1.
2.
3.
Stand in front of the system and open the
top cover.
Use the thumb and index finger of your
right hand to flip up the right handle, and
the thumb and index finger of your left
hand to flip up the left handle of the fan
that you want to remove.
Firmly hold the handles and pull up
the fan until it is disengaged from its
connector.
Avoid touching the fan blades while
removing the fan. Spinning fan blades
may cause injury!
Note on the power supply mid-fan
When you re-install the mid-fan for the power
supply module(s) make sure that the arrow
points to the direction of the rear panel.
Installing the fan otherwise will cause CPU
overheating.
2-30
Chapter 2: Hardware setup
Note on the power supply mid-fan
When you re-install the mid-fan for the CPU(s), make sure that the four fans
designed for the CPUs cooling (labeled CPU) are installed in the correct
place. Installing the lower-speed fans for CPU will cause CPU overheating.
2.7.2
Power supply modules
According to your needs, the barebone system ships with one power supply
module or two. The one-power-supply model will ship with a metal bracket cover
for the empty bay.
To install a second power supply module:
1.
2.
3.
4.
Locate the empty power supply bay on the rear panel covered with a metal
bracket.
Loosen the screws that fasten the cover, one on the top and the other on the
rear.
Use the screw driver to remove the cover.
Insert the second power supply module
Remove the AC power cord, first pressing the latch.
HPC-2820-ISSE User Manual
2-31
To uninstall a power supply module:
1.
2.
Locate the power supply modules on the rear panel, and select the module
that you want to remove.
Hold the module lever and press the latch on the inner side to release the
module.
PSU1
PSU2
3.
4.
2-32
Firmly pull the lever to slide the
power supply module out of the
chassis.
Repeat steps 2 to 3 to remove the
other module.
Chapter 2: Hardware setup
2.7.3
Slim optical and floppy drives
To uninstall the optical and floppy disk drives:
1.
Disconnect the power and signal
cables connected to the rear of the
drives.
Signal cable
Power cable
2.
Loosen the two screws that secure
the drive bracket to the chassis.
The optical drive is attached to the
top of the bracket, and the floppy
drive to bottom.
3.
Slide the drive bracket toward the
SCSI backplanes to release it from
the chassis, then carefully pull it out
of the drive bay.
HPC-2820-ISSE User Manual
2-33
2.7.4
Front panel LED and switch board
To uninstall the front panel and swtich board:
1.
2.
Disconnect all cables connected to the rear of the board.
Remove sticker on the front panel and unscrew the board to the chassis.
3. Carefully remove the board out of the chassis.
When removed, the LED and switch board appears as shown. The LEDs and
switches on the board correspond to the LEDs and buttons on the system front
panel.
Locator LED connector (red/black)
Locator switch connector (blue/white)
Panel connector
Front USB connector
Front side
2-34
Rear side
Chapter 2: Hardware setup
2.7.5
SAS backplane
To uninstall a SAS backplane:
1.
Disconnect all cables connected to the rear of the SAS backplane.
3.
Loosen all the screws on the SAS backplane.
2.
Carefully lift the backplane upward to remove it from the chassis.
2.7.6 System fan board
To uninstall the system-fan boards:
1.
Remove the three screws that fasten the rack fan, one on the right side, two
on the left.
HPC-2820-ISSE User Manual
2-35
2.
Remove all the fans and unscrew the fan rack.
4.
Remove rack fan for the power supply first and then loosen the screw that
fastens the fan rack to the power supply cage.
3.
5.
6.
7.
2-36
Unplug the cables connected to the mid-fan board.
Carefully lift the fan rack upward to remove it from the chassis.
Unscrew the mid-fan board and remove it from the fan rack.
Unscerw the main fan boards and remove them from the chassis.
Chapter 2: Hardware setup
2.7.7
Power supply cage
To uninstall a power supply cage:
1.
2.
Follow the instructions in 2.7.2 Power supply module to remove the
installed modules.
Follow the instructions in 2.7.6 System fan board to remove the fan rack.
3.
Loosen the three screws that
fasten the power supply cage.
4.
Carefully lift the power supply
cage upward a little to remove it
from the chassis.
HPC-2820-ISSE User Manual
2-37
2.7.8
LAN adapter (Optional)
For your convenience, install a LAN adapter into the LAN port before you connect
the LAN.
To install a LAN adapter:
1.
2.
Orient the LAN adapter and then
plug it into the LAN port.
Connect your network cable to
the LAN adapter.
To uninstall a LAN adapter:
1.
Remove the screw on the top cover.
2.
Press the tabs on each side of the rear fan cover with both hands and then
remove it from the chassis.
4.
Disconnect the LAN adapter from the rear panel of the system.
2.7.9
LAN cable
To disconnect a LAN cable:
Follow the same instructions of uninstalling a LAN adapter.
2-38
Chapter 2: Hardware setup
CHAPTER
3
Installation Options
3-
3.1
Rackmount rail kit items
Your rackmount rail kit package contains:
•
•
•
one pair of server rails (for the server)
two pairs of rack rails (for the rack)
* to accommodate different sizes of rack
Nut-and-bolt type screws
Rear end
Server rails
Rack rails
Nuts-and-screws
Front end
3-
•
The rear ends come pre-installed in the rack rails. The rear end nuts and
screws are loosen to allow flexible installation on the industrial rack.
•
Install the server in an industrial rack with at least 100 cm depth.
Chapter 3: Installation options
3.2
Attaching the rails to the server
To attach the server rails:
1.
Locate the hooks on the side of the
chassis.
2.
Position a server rail parallel to the
side of the chassis, and match each
of the five hooks to the holes on the
rail.
Side hook locked to rail
hole
3.
Secure the server rail to the side of
the chassis with two screws.
4.
Repeat steps 1 to 3 to attach the second server rail to the other side of the
chassis.
HPC-2820-ISSE User Manual
3-
3.3
Attaching the rack rails
To attach the rack rails:
1.
2.
3.
4.
5.
7.
3-
Select two units of space (2U) on the rack where you want to install the
barebone server.
Install the nuts on the holes of the 2U space on the rack front.
Install the nuts on the holes of the 2U space on the corresponding rack rear.
Measure the depth of the rack to determine the length of the rack rails.
Take two pieces of rack rail,
consisting of the middle piece with
the pre-installed rear end, and one
front end (left or right).
Attach the front end to the middle
piece using the supplied nuts and
screws. Make sure that the front end
dent supports the middle piece.
Middle piece
Dent
Left front of the
rack
Right front of
the rack
Measure the rack rail when
assembled to make sure that it fits
the rack.
Chapter 3: Installation options
8.
Position the rack rail to the 2U
space on the rack. Make sure that
the front end of the rack rail goes to
the front of the rack space.
9.
Secure the front end of the rail with
two rack screws.
10. Secure the rear end of the rail with
two rack screws.
11. Repeat steps 5 to 9 to assemble
and attach the second rack rail.
HPC-2820-ISSE User Manual
3-
3.4
Rackmounting the server
To mount the server to the rack:
1.
Align the server rails with the rack rails and push the server halfway to the
rack.
2.
Align a mounting ear with the holes
on a front corner of the chassis,
then secure it with two screws.
3.
4.
5.
3-
Attach the other mounting ear to the
other corner of the chassis.
Pull the server rail lock, then push
the server all the way to the depth of
the rack.
Make sure that the mounting ear
and the rack screw holes align.
Drive a screw on the mounting ear
to secure the server in place.
Chapter 3: Installation options
CHAPTER
4
Motherboard Information
4.1
Motherboard layout
Make sure to unplug the chassis power cord before installing or removing
the motherboard. Failure to do so can cause you physical injury and damage
motherboard components!
33cm (13in)
KBPWR1
PS/2
T: Mouse
B: Keyboard
CPU_FAN1
ATX12V1
ATX12V2
DDR FB-DIMM_12 (64/72 bit, 240-pin module)
USB1
USB2
DDR FB-DIMM_11 (64/72 bit, 240-pin module)
FBD_FAN1
COM1
ATXPWR1
PSUSMB1
USBPW12
CPU1
DDR FB-DIMM_10 (64/72 bit, 240-pin module)
DDR FB-DIMM_02 (64/72 bit, 240-pin module)
REAR_FAN1
DDR FB-DIMM_01 (64/72 bit, 240-pin module)
FBD_FAN2
RJ-45
(LAN1)
Intel®
5000P
CPU2
DDR FB-DIMM_20 (64/72 bit, 240-pin module)
RJ-45
(LAN2)
DDR FB-DIMM_21 (64/72 bit, 240-pin module)
ASMB3
DDR FB-DIMM_32 (64/72 bit, 240-pin module)
FRNT_FAN4
DDR FB-DIMM_31 (64/72 bit, 240-pin module)
FRNT_FAN2
CPU_FAN2
DDR FB-DIMM_30 (64/72 bit, 240-pin module)
82563EB
FRNT_FAN1
DDR FB-DIMM_22 (64/72 bit, 240-pin module)
30.5cm (12in)
DSBF-D12/2U/SAS
VGA1
DDR FB-DIMM_00 (64/72 bit, 240-pin module)
REAR_FAN2
PRI_IDE1
AMI
8Mb
FWH
ATI
ES1000
TPM1
SATA1
SATA2
PCIE1EXT1
RECOVERY1
DIP_SW1
Super
I/O
CLRTC1
CR2032 3V
Lithium Cell
CMOS Power
SAS_EN1
LPC1
LAN_BW1
LSI
SAS1068
LPT1
COM2
4.1.1
®
Intel
6321ESB
SAS2
SAS1
BUZZER1
VGA_EN1
USBPW34
SB_PWR1
HDLED1
SATA3
SATA4
PCIE1
SATA5
SATA6
LAN_EN1
SLIM_PCIX5
SGPIO1
FLOPPY1
SASLED1
USB34
AUX_PANEL1
FRNT_FAN3
PANEL1
BPSMB1
Screw holes
Place eight (8) screws into the holes indicated by circles to secure the motherboard
to the chassis.
Place this side towards
the rear of the chassis
4-
DSBF-D12/2U/SAS
Do not overtighten the screws! Doing so can damage the motherboard.
Chapter 4: Motherboard information
4.1.2
Layout contents
Jumpers
Page
1. Clear RTC RAM (CLRTC1)
4-6
3. USB device wake-up (3-pin USBPW12, USBPW34)
4-7
2. LAN bandwidth setting (3-pin LAN_BW1)
4. Keyboard power (3-pin KBPWR1)
5. VGA controller setting (3-pin VGA_EN1)
6. Onboard storage setting (3-pin SAS_EN1)
4-7
4-8
4-8
4-9
Switch
Page
1. DIP switch (DIP_SW1)
4-10
Internal connectors
Page
1. Floppy disk drive connector (34-1 pin FLOPPY1)
4-11
3. Serial ATA connectors
(7-pin SATA1, SATA2, SATA3, SATA4, SATA5, SATA6 )
4-12
5. Mini-SAS connectors
4-13
2. IDE connector (40-1 pin PRI_IDE)
4-11
4. Hard disk activity LED connector (4-pin HDLED1)
4-12
6. USB connector (10-1 pin USB34)
4-14
7. Serial port connector (10-1 pin COM2)
8. CPU and system fan connectors
(4-pin CPU_FAN1/2, REAR_FAN1/2, FRNT_FAN1/2/3/4, FBD_FAN1/2)
4-14
4-15
9. Power supply SMBus connector (5-pin PSUSMB1)
4-15
11. Parallel port connector (26-1 pin LPT1)
4-17
13. SAS LSI1068 ports LED connector (18-1 pin SASLED1)
4-18
10. SSI power connectors
(24-pin ATXPWR1, 8-pin ATX12V1, 4-pin ATX12V2)
12. Backplane SMBus connector (7-1 pin BPSMB1)
14. Serial General Purpose Input/Output connector (6-1 pin SGPIO1)
15. System panel connector (20-1 pin PANEL1)
16. Auxiliary panel connector (20-2 pin AUX_PANEL1)
17. Trusted Platform Module connector (20-1 pin TPM1)
18. LPC connector for LPC debug card (14-1 pin LPC1)
HPC-2820-ISSE User Manual
4-16
4-17
4-18
4-19
4-20
4-21
4-21
4-
4.2
Support kits for the motherboard
For additional protection from motherboard breakage due to the weight of the CPU
heatsinks, your motherboard package comes with CEK springs that you can use as
weight support. Install the CEK springs if you want to install a new motherboard.
If your chassis is SSI EEB 3.61 compliant, we recommend that you use the CEK
springs; otherwise, use the support plates kit.
Each CEK spring has four hooks to match the
designated holes around the CPU area.
Hook
To install the CEK spring:
1.
Locate the CPU heatsink holes on
the motherboard.
Socket for CPU1
Heatsink hole
Socket for CPU2
2.
4-
Position the CEK spring underneath
the motherboard, then match the
CEK spring hooks to the CPU1
heatsink holes.
Chapter 4: Motherboard information
3.
Press the upper spring hooks
inward, then insert to the upper
CPU heatsink holes until they snap
in place.
4.
Press the lower spring clips
inward, then insert to the lower
CPU heatsink holes until they snap
in place.
5.
If you installed a second CPU, repeat steps 2 to 4 to install the CEK spring to
the CPU2 heatsink holes.
6.
Install the motherboard with the
external I/O ports toward the
chassis rear panel. The CPU
sockets should be right on top of
their respective standoffs.
CPU1
socket
CPU2
socket
Make sure that the standoffs perfectly match the CEK spring screw holes;
otherwise, you can not install the CPU heatsinks properly.
7.
Secure the motherboard with screws. Refer to section “4.1.1 Screw holes” for
illustration.
HPC-2820-ISSE User Manual
4-
4.3
1.
Jumpers
Clear RTC RAM (CLRTC1)
This jumper allows you to clear the Real Time Clock (RTC) RAM in CMOS.
You can clear the CMOS memory of date, time, and system setup parameters
by erasing the CMOS RTC RAM data. The onboard button cell battery
powers the RAM data in CMOS, which include system setup information such
as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Remove the onboard battery.
3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on
pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2.
4. Reinstall the battery.
5. Plug the power cord and turn ON the computer.
6. Hold down the <Del> key during the boot process and enter BIOS setup
to re-enter data.
®
Except when clearing the RTC RAM, never remove the cap on CLRTC jumper
default position. Removing the cap will cause system boot failure!
CLRTC1
1 2
Clear RTC RAM
4-
2 3
Normal
(Default)
Clear CMOS
Chapter 4: Motherboard information
LAN bandwidth setting (3-pin LAN_BW1)
This jumper allows you to set the LAN bandwidth setting for more efficient IP
load distribution.
®
2.
LAN_BW1
1 2
LAN bandwidth setting
2 3
Balanced mode
(Default)
Centric mode
Balance Mode: It's x8 link between MCH and ESB2;
LAN Centrical Mode: It's x4 link between MCH and ESB2.
3.
USB device wake-up (3-pin USBPW12, USBPW34)
Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU
stopped, DRAM refreshed, system running in low power mode) using the
connected USB devices. Set to +5VSB to wake up from S4 sleep mode (no
power to CPU, DRAM in slow refresh, power supply in reduced power mode).
USBPW12
1 2
®
+5V
(Default)
2 3
+5VSB
USBPW34
1 2
+5V
(Default)
2 3
+5VSB
USB device wake up
•
The USB device wake-up feature requires a power supply that can
provide 500mA on the +5VSB lead for each USB port; otherwise, the system
will not power up.
•
If you are using Windows® 2000, you need to install Service Pack 4 to wake
up the system from S4 sleep mode.
•
The total current consumed must NOT exceed the power supply capability
(+5VSB) whether under normal condition or in sleep mode.
HPC-2820-ISSE User Manual
4-
4.
Keyboard power (3-pin KBPWR1)
This jumper allows you to enable or disable the keyboard wake-up feature.
Set this jumper to pins 2-3 (+5VSB) to wake up the computer when you press
a key on the keyboard (the default is the Space Bar). This feature requires
an ATX power supply that can supply at least 1A on the +5VSB lead, and a
corresponding setting in the BIOS.
KBPWR1
2 3
®
1 2
+5V
(Default)
+5VSB
Keyboard power setting
VGA controller setting (3-pin VGA_EN1)
These jumpers allow you to enable or disable the onboard VGA controller.
Set to pins 1-2 to activate the VGA feature.
®
5.
VGA_EN1
1 2
VGA setting
4-
2 3
Enable
(Default)
Disable
Chapter 4: Motherboard information
Onboard storage setting (3-pin SAS_EN1)
This jumper allows you to enable or disable the onboard LSI1068 SAS
controller.
®
6.
SAS_EN1
1 2
SAS setting
HPC-2820-ISSE User Manual
Enable
(Default)
2 3
Disable
4-
4.4
Switch
This motherboard features a DIP switch for fan pin selection.
DIP_SW1
®
ON
ON
1 2 3 4 5 6 7 8
OFF(Default)
DIP switches
ON:4-PIN FAN
OFF:3-PIN FAN
SW1_CPU_FAN1
SW2_CPU_FAN2
SW3_FRNT_FAN1
SW4_FRNT_FAN2
SW5_FRNT_FAN3
SW6_FRNT_FAN4
SW7_REAR_FAN1
SW8_REAR_FAN2
The following table shows the corresponding switch for each fan connector.
Switch
1
2
3
4
5
6
7
8
4-10
Fan connector
CPU_FAN1
CPU_FAN1
FRNT_FAN1
FRNT_FAN2
FRNT_FAN3
FRNT_FAN4
REAR_FAN1
REAR_FAN2
Default setting
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
•
If you use a 4-pin fan but set the DIP switch for a 3-pin fan, the fan you
installed may not work.
•
If you use a 3-pin fan but set the DIP switch for a 4-pin fan, the fan controll
will not work and the fan you installed will always run at full speed.
Chapter 4: Motherboard information
4.5
1.
Connectors
Floppy disk drive connector (34-1 pin FLOPPY1)
This connector is for the provided floppy disk drive (FDD) signal cable. Insert
one end of the cable to this connector, then connect the other end to the
signal connector at the back of the floppy disk drive.
®
Pin 5 on the connector is removed to prevent incorrect cable connection when
using a FDD cable with a covered Pin 5.
FLOPPY1
PIN 1
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
Floppy disk drive connector
IDE connector (40-1 pin PRI_IDE1)
This connector is for an Ultra DMA 100/66 signal cable. The Ultra
DMA 100/66 signal cable has three connectors: a blue connector for the
primary IDE connector on the motherboard, a black connector for an Ultra
DMA 100/66 IDE slave device (optical drive/hard disk drive), and a gray
connector for an Ultra DMA 100/66 IDE master device (hard disk drive). If you
install two hard disk drives, you must configure the second drive as a slave
device by setting its jumper accordingly. Refer to the hard disk documentation
for the jumper settings.
•
Pin 20 on the IDE connector is removed to match the covered hole on the
Ultra DMA cable connector. This prevents incorrect insertion when you
connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
®
2.
PRI_IDE1
PIN 1
IDE connector
HPC-2820-ISSE User Manual
4-11
3.
Serial ATA connectors.
(7-pin SATA1, SATA2, SATA3, SATA4, SATA5, SATA6 )
These connectors are for the Serial ATA signal cables for Serial ATA hard disk
drives.
SATA2
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXN1
RSATA_RXP1
GND
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXN2
RSATA_RXP2
GND
SATA3
SATA4
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXN3
RSATA_RXP3
GND
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXN4
RSATA_RXP4
GND
SATA5
SATA6
GND
RSATA_TXP5
RSATA_TXN5
GND
RSATA_RXN5
RSATA_RXP5
GND
GND
RSATA_TXP6
RSATA_TXN6
GND
RSATA_RXN6
RSATA_RXP6
GND
®
SATA1
SATA connectors
Hard disk activity LED connector (4-pin HDLED1)
NC
ADD_IN_CARDADD_IN_CARDNC
This connector is used to connect to a hard disk drive active LED connector
on the SCSI or RAID card.
®
4.
PIN1
HDLED1
9torage card activity LED connector
4-12
Chapter 4: Motherboard information
Mini-SAS connectors
This motherboard comes with two Serial Attached SCSI (SAS) connectors,
the next-generation storage technology that supports both Serial Attached
SCSI and Serial ATA. Each connector supports up to four (4) devices.
®
5.
MINI SAS connectors
To connect the mini-SAS cable:
Plug in the mini-SAS cable to the
mini-SAS connector until the cable
lock snaps in place.
To disconnect the mini-SAS cable:
1.
2.
With your thumb, push down the
cable lock to release.
While still keeping your thumb’s
grip on the cable lock, carefully pull
away the cable from the connector
HPC-2820-ISSE User Manual
1
2
4-13
USB connector (10-1 pin USB34)
This connector is for USB 2.0 ports. Connect the USB module cable to
this connector, then install the module to a slot opening at the back of the
system chassis. This USB connector complies with USB 2.0 specification that
supports up to 480 Mbps connection speed.
Power
USB PortB(-)
USB PortB(+)
GND
NC
®
6.
USB34
Power
USB PortA(-)
USB PortA(+)
GND
PIN1
USB connector
Serial port connector (10-1 pin COM2)
This connector is for a serial (COM) port. Connect the serial port module
cable to this connector, then install the module to a slot opening at the back
of the system chassis.
®
7.
COM2
Serial port connector
PIN1
The serial port module is purchased separately.
4-14
Chapter 4: Motherboard information
8.
CPU and system fan connectors.
(4-pin CPU_FAN1/2, REAR_FAN1/2, FRNT_FAN1/2/3/4, FBD_FAN1/2)
The fan connectors support cooling fans of 350 mA ~ 740 mA (8.88 W max.)
or a total of 2.1 A ~ 4.44 A (53.28 W max.) at +12V. Connect the fan cables
to the fan connectors on the motherboard, making sure that the black wire of
each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors. Insufficient air
flow inside the system may damage the motherboard components. These are
not jumpers! Do not place jumper caps on the fan connectors!
GND
FAN Power
FAN Speed
PWM Control
REAR_FAN1 REAR_FAN2
FRNT_FAN1 FRNT_FAN2
FRNT_FAN3
Fan connectors
9.
GND
FAN Power
FAN Speed
PWM Control
FRNT_FAN3
GND
FAN Power
FAN Speed
PWM Control
GND
FAN Power
FAN Speed
PWM Control
FBD_FAN1
PWM Control
FAN Speed
FAN Power
GND
CPU_FAN2
FBD_FAN2
GND
FAN Power
FAN Speed
PWM Control
PWM Control
FAN Speed
FAN Power
GND
FRNT_FAN4
PWM Control
FAN Speed
FAN Power
GND
FBD_FAN2
CPU_FAN2
FRNT_FAN1
FRNT_FAN2
FRNT_FAN4
CPU_FAN1
PWM Control
FAN Speed
FAN Power
GND
®
FBD_FAN1
REAR_FAN1
REAR_FAN2
PWM Control
FAN Speed
FAN Power
GND
CPU_FAN1
Power supply SMBus connector (5-pin PSUSMB1)
This connector is for the power supply SMB cable, if your power supply
supports the SMBus function.
I2C_7_CLK#
I2C_7_DATA#
NC
GND
+3.3V Remote Sense
®
PSUSMB1
Power supply SMBus connector
HPC-2820-ISSE User Manual
4-15
10. SSI power connectors (24-pin ATXPWR1, 8-pin ATX12V1, 4-pin ATX12V2)
These connectors are for SSI power supply plugs. The power supply plugs
are designed to fit these connectors in only one orientation. Find the proper
orientation and push down firmly until the connectors completely fit.
•
For a fully configured system, we recommend that you use an SSI
12 V-compliant power supply unit (PSU) for LGA771‑socket Intel® Xeon
Dual Core processors (Bensley platform).
•
Do not forget to connect the 24+8+4-pin power plugs; otherwise, the
system will not boot up.
•
Use of a PSU with a higher power output is recommended when
configuring a system with more power consuming devices. The system may
become unstable or may not boot up if the power is inadequate.
•
You must install a PSU with a higher power rating if you intend to install
additional devices.
ATXPWR1
ATX12V1
8-pin
12V1
12V1
12V2
12V2
+3 Volts
-12 Volts
Ground
PSON#
Ground
Ground
Ground
-5 Volts
+5 Volts
+5 Volts
+5 Volts
Ground
®
GND
GND
GND
GND
+3 Volts
+3 Volts
Ground
+5 Volts
Ground
+5 Volts
Ground
Power OK
+5V Standby
+12 Volts
+12 Volts
+3 Volts
24-pin Power Connector
+12V DC GND
ATX12V2
ATX power connectors
4-16
4-pin
+12V DC GND
Chapter 4: Motherboard information
11. Parallel port connector (26-1 pin LPT1)
SLCT
PE
BUSY
ACK#
SPD7
SPD6
SPD5
SPD4
SPD3
SPD2
SPD1
SPD0
STB#
®
This connector is for a parallel port. Connect the parallel port module cable
to this connector, then install the module to a slot opening at the back of the
system chassis.
PIN1
GND
GND
GND
GND
GND
GND
GND
GND
SLIN#
PINIT#
ERROR#
AFD#
LPT1
Parallel port connector
The parallel port module is purchased separately.
12. Backplane SMBus connector (7-1 pin BPSMB1)
®
This connector allows you to connect SMBus (System Management Bus)
devices. Devices communicate with an SMBus host and/or other SMBus
devices using the SMBus interface.
BPSMB1
HPC-2820-ISSE User Manual
GND
12CDAT P2
+5V
FAN_PWM
BPSMB connector
FAN_DC1
I2CCLK P2
PIN1
4-17
13. SAS LSI1068 ports LED connector (18-1 pin SASLED1)
ACT_LED6
ACT_LED7
ACT_LED0
ACT_LED1
ACT_LED2
ACT_LED3
ACT_LED4
ACT_LED5
®
This connector is for the front panel LED port indicator that shows the SAS
HDD status.
PIN1
SASLED connector
FLT_LED0
FLT_LED1
FLT_LED2
FLT_LED3
GND
FLT_LED4
FLT_LED5
FLT_LED6
FLT_LED7
SASLED1
14. Serial General Purpose Input/Output connector (6-1 pin SGPIO1)
®
This connector is used for the SGPIO peripherals for the LSI MegaRAID
SATA LED.
SGPIO1
4-18
GND
SATA_SLOAD
SATA_SCLK
SGPIO connector
SDATAOUT0
SDATAOUT1
PIN1
Chapter 4: Motherboard information
15. System panel connector (20-1 pin PANEL1)
This connector supports several chassis-mounted functions.
POWERLED+
NC
POWERLEDMLED+
MLEDNC
+5V
GND
GND
SPKROUT
®
The system panel connector is color-coded for easy connection.
NMIBTN#
GND
POWERBTN#
GND
NC
RESETBTN#
GND
System panel connector
IDELED+
IDELED-
PANEL1
•
System power LED (Green 3-pin PLED)
•
Hard disk drive activity LED (Red 2-pin IDE_LED)
•
System warning speaker (Orange 4-pin SPEAKER)
•
ATX power button/soft-off button (Yellow 2-pin PWRSW)
•
Reset button (Blue 2-pin RESET)
This 3-pin connector is for the system power LED. Connect the chassis power
LED cable to this connector. The system power LED lights up when you turn
on the system power, and blinks when the system is in sleep mode.
This 2-pin connector is for the HDD Activity LED. Connect the HDD Activity
LED cable to this connector. The IDE LED lights up or flashes when data is
read from or written to the HDD.
This 4-pin connector is for the chassis-mounted system warning speaker. The
speaker allows you to hear system beeps and warnings.
This connector is for the system power button. Pressing the power button
turns the system on or puts the system in sleep or soft-off mode depending
on the BIOS settings. Pressing the power switch for more than four seconds
while the system is ON turns the system OFF.
This 2-pin connector is for the chassis-mounted reset button for system
reboot without turning off the system power.
HPC-2820-ISSE User Manual
4-19
16. Auxiliary panel connector (20-2 pin AUX_PANEL1)
This connector is for additional front panel features including front panel SMB,
locator LED and switch, chassis intrusion, and LAN LEDs.
2
2
GND
I2C_4_DATA#
+5VSB
LAN1_LINK
LAN1_ACT
LAN2_ACT
LAN2_LINK
NC
I2C_4_CLK#
®
1
+5VSB
PIN1
Auxiliary panel connector
1
CASEOPEN
GND
LOCATORLED1+
LOCATORLED1LOCATORBTN#
GND
LOCATORLED2LOCATORLED2+
AUX_PANEL1
3
4
5
4
Front panel SMB (6-1 pin FPSMB)
These leads connect the front panel SMBus cable.
2
LAN activity LED (2-pin LAN1_LED, LAN2_LED)
3
Chassis intrusion (2 pin CHASSIS)
These leads are for Gigabit LAN activity LEDs on the front panel.
These leads are for the intrusion detection feature for chassis with
intrusion sensor or microswitch. When you remove any chassis
component, the sensor triggers and sends a high-level signal to these
leads to record a chassis intrusion event.
4/5 Locator LED/Switch (6-pin LOCATOR)
These leads are for the locator switch and LED on the front panel.
4-20
Chapter 4: Motherboard information
17. TPM connector (20-1 pin TPM)
This connector supports a Trusted Platform Module (TPM) system, which can
securely store keys, digital certificates, passwords, and data. A TPM system
also helps enhance network security, protects digital identities, and ensures
platform integrity.
CK_33M_TPM
LFRAMEn
LRESETn
LAD3
+3.3V
LAD0
+3.3V
X
GND
X
®
TPM1
X
GPIO2
GPIO
LAD2
LAD1
GND
X
SERIRQ
X
X
PIN1
TPM connector
18. LPC debug card connector.(14-1 pin LPC1)
+3.3V
GND
LPC_LAD2
LPC_LAD0
PLTRST
CLK
®
This is a low pin count interface used to plug in the LPC debug card.
LPC debug card connector
PIN1
+3.3V
+3.3V
GND
LPC_LAD3
LPC_LAD1
LFRAME_N
GND
LPC1
This connector is for RMA engineer to debug only.
HPC-2820-ISSE User Manual
4-21
4-22
Chapter 4: Motherboard information
CHAPTER
5
BIOS Setup
5-
5.1
Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard Basic
Input/Output System (BIOS) setup:
1.
Phoenix Phlash16 BIOS Flash Utility (Updates the BIOS in DOS mode
using a bootable floppy disk.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable floppy disk in
case you need to restore the BIOS in the future. Copy the original motherboard
BIOS using Phoenix Phlash16 BIOS utilities. Refer to page 4-3 for details.
5.1.1
1.
Creating a bootable floppy disk
Do either one of the following to create a bootable floppy disk.
DOS environment
a. Insert a 1.44MB floppy disk into the drive.
b. At the DOS prompt, type format A:/S then press <Enter>.
Windows® XP environment
a. Insert a 1.44 MB floppy disk to the floppy disk drive.
5-
b. Click Start from the Windows® desktop, then select My Computer.
c. Select the 3 1/2 Floppy Drive icon.
d. Right-click File from the menu, then select Format. A Format 3 1/2 Floppy Disk window appears.
e. Select Create an MS-DOS startup disk from the format options field,
then click Start.
Chapter 5: BIOS setup
5.1.2
Updating the BIOS using the Phoenix Phlash16 .
Utility
The Basic Input/Output System (BIOS) can be updated using the Phoenix
Phlash16 Utility. Follow these instructions to update the BIOS using this utility.
1. Download the latest BIOS file from the Advantech web site. Rename the file
to BIOS.WPH. Save the file to a floppy disk.
Make sure you copy the correct BIOS file for the specific model of your
motherboard. Save only the updated BIOS file in the floppy disk to avoid loading
the wrong BIOS file.
2.
3.
Copy the Phoenix Phlash16 (phlash16.exe) utility from the Software folder of
the support CD to the floppy disk with the latest BIOS file.
Boot the system in DOS mode using the bootable floppy disk you created
earlier.
4. When the A:> appears, replace the bootable floppy disk with the floppy disk
containing the new BIOS file and the Phoenix Phlash16 Utility.
5.
At the prompt, type the following command string:
phlash16 /x /mode=3 BIOS.WPH.
6.
The Phoenix Phlash16 Utility automatically updates the BIOS.
Do not turn off or reset the system during the flashing process!
7.
Restart the system after the utility completes the updating process. Make
sure you remove the floppy disk from the drive
HPC-2820-ISSE User Manual
5-
5.2
BIOS setup program
This motherboard supports a programmable Low-Pin Count (LPC) chip that you
can update using the provided utility described in section “4.1 Managing and
updating your BIOS.”
Use the BIOS Setup program when you are installing a motherboard, reconfiguring
your system, or prompted to “Run Setup.” This section explains how to configure
your system using this utility.
Even if you are not prompted to use the Setup program, you can change the
configuration of your computer in the future. For example, you can enable the
security password feature or change the power management settings. This
requires you to reconfigure your system using the BIOS Setup program so that the
computer can recognize these changes and record them in the CMOS RAM of the
LPC chip.
The LPC chip on the motherboard stores the Setup utility. When you start up the
computer, the system provides you with the opportunity to run this program. Press
<Del> during the Power-On Self-Test (POST) to enter the Setup utility; otherwise,
POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing <Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis. You can
also restart by turning the system off and then back on. Do this last option only if
the first two failed.
The Setup program is designed to make it as easy to use as possible. Being a
menu-driven program, it lets you scroll through the various sub-menus and make
your selections from the available options using the navigation keys.
5-
•
The default BIOS settings for this motherboard apply for most conditions
to ensure optimum performance. If the system becomes unstable after
changing any BIOS settings, load the default settings to ensure system
compatibility and stability. Select the Load Default Settings item under the
Exit Menu. See section “4.8 Exit Menu.”
•
The BIOS setup screens shown in this section are for reference purposes
only, and may not exactly match what you see on your screen.
Chapter 5: BIOS setup
5.2.1
BIOS menu screen
Menu items
Main
Menu bar
Advanced
Server
Configuration fields
General help
PhoenixBIOS Setup Utility
Security
Boot
Exit
System Date
System Time
[09/08/2006]
[15 : 30 : 36]
Floppy A
[1.44/1.25 MB 31/2”]
IDE Configuration
IDE Channel 0 Master
IDE Channel 0 Slave
SATA Port 1
SATA Port 2
SATA Port 3
SATA Port 4
[None]
[None]
[None]
[None]
[None]
[None]
Item Specific Help
<Tab>, <Shift+Tab>, or
<Enter> selects field.
System Information
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
Sub-menu items
5.2.2
Legend bar
Menu bar
The menu bar on top of the screen has the following main items:
Main
For changing the basic system configuration
Advanced
For changing the advanced system settings
Security
For changing the security settings
Server
Boot
Exit
For changing the advanced server settings
For changing the system boot configuration
For selecting the exit options and loading default settings
To select an item on the menu bar, press the right or left arrow key on the keyboard
until the desired item is highlighted.
HPC-2820-ISSE User Manual
5-
5.2.3
Legend bar
At the bottom of the Setup screen is a legend bar. The keys in the legend bar allow
you to navigate through the various setup menus. The following table lists the keys
found in the legend bar with their corresponding functions.
Navigation key
Function
<F9>
Loads setup default values
<F1>
<Esc>
Left or Right arrow
Up or Down arrow
Page Down or
– (minus)
Displays the General Help screen
Exits the BIOS setup or returns to the main menu from a
sub‑menu
Selects the menu item to the left or right
Moves the highlight up or down between fields
Scrolls backward through the values for the highlighted field
Page Up or + (plus)
Scrolls forward through the values for the highlighted field
<F10>
Saves changes and exit
<Enter>
5.2.4
Brings up a selection menu for the highlighted field
Menu items
The highlighted item on the menu bar displays the specific items for that menu.
For example, selecting Main shows the Main menu items.
The other items (Advanced, Power, Boot, and Exit) on the menu bar have their
respective menu items.
5.2.5
Sub-menu items
A solid triangle before each item on any menu screen means that the iteam has a
sub-menu. To display the sub-menu, select the item and press <Enter>.
5.2.6
Configuration fields
These fields show the values for the menu items. If an item is user‑configurable,
you can change the value of the field opposite the item. You cannot select an item
that is not user-configurable.
A configurable field is enclosed in brackets, and is highlighted when selected. To
change the value of a field, select it then press <Enter> to display a list of options.
Refer to “5.2.7 Pop-up window.”
5-
Chapter 5: BIOS setup
5.2.7
Pop-up window
Select a menu item then press <Enter> to display a pop-up window with the
configuration options for that item.
Main
Advanced
Server
PhoenixBIOS Setup Utility
Security
Boot
Exit
System Date
System Time
[09/08/2006]
[15 : 30 : 36]
Floppy A
[1.44/1.25 MB 31/2”]
IDE Configuration
IDE Channel 0 Master
IDE Channel 0 Slave
SATA Port 1
SATA Port 2
SATA Port 3
SATA Port 4
System Information
F1:Help
ESC: Exit
[None]
[None]
Disabled
[None]
360
Kb [None]
1.2
MB [None]
[None]
720 Kb 1.44/1.25 MB
2.88 MB ↑↓ :Select Item
→← :Select Menu
Item Specific Help
5
5
3
3
3
<Tab>, <Shift+Tab>, or
<Enter> selects field.
1/4”
1/4”
1/2”
1/2”
1/2”
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
Pop-up menu
5.2.8
General help
At the top right corner of the menu screen is a brief description of the selected item.
HPC-2820-ISSE User Manual
5-
5.3
Main menu
When you enter the BIOS Setup program, the Main menu screen appears, giving
you an overview of the basic system information.
Refer to section “5.2.1 BIOS menu screen” for information on the menu screen
items and how to navigate through them.
Main
Advanced
Server
PhoenixBIOS Setup Utility
Security
Boot
Exit
System Date
System Time
[09/08/2006]
[15 : 30 : 36]
Floppy A
[1.44/1.25 MB 3½”]
IDE Configuration
IDE Channel 0 Master
IDE Channel 0 Slave
SATA Port 1
SATA Port 2
SATA Port 3
SATA Port 4
[None]
[None]
[None]
[None]
[None]
[None]
Item Specific Help
<Tab>, <Shift+Tab>, or
<Enter> selects field.
System Information
F1:Help
ESC: Exit
5.3.1
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
System Date [Day xx/xx/xxxx]
Allows you to set the system date.
5.3.2
System Time [xx:xx:xx]
Allows you to set the system time.
5.3.3
Floppy A [1.44M, 3½in.]
Sets the type of floppy drive installed.
Configuration options: [Disabled] [360 Kb 5¼”] [1.2 MB 5¼”] [720 Kb 3 ½” ]
[1.44/1.25 MB 3 ½”] [2.88 MB 3½”]
5-
Chapter 5: BIOS setup
5.3.4
IDE Configuration
PhoenixBIOS Setup Utility
Main
IDE Configuration
Fixed disk boot sector:
Item Specific Help
[Normal]
S-ATA Configuration
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Write protects boot
sector on hard disk
to protect against
viruses.
F5: Setup Defaults
F10: Save and Exit
Fixed disk boot sector [Normal]
Setting this item to [Write Protect] prevents write access to the boot sector on
the hard disk to protect against viruses. The default setting [Normal] allows write
access. Configuration options: [Normal] [Write Protect]
S-ATA Configuration
PhoenixBIOS Setup Utility
Main
S-ATA Configuration
Item Specific Help
Parallel ATA
[Enabled]
Serial ATA:
[Enabled]
SATA Controller Mode Option: [Enhanced]
SATA RAID Enable
[Disabled]
SATA AHCI Enable
[Disabled]
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Enable the PATA
F5: Setup Defaults
F10: Save and Exit
Parallel ATA [Enabled]
Allows you to enable or disable the parallel ATA function.
Configuration options: [Disabled] [Enabled]
HPC-2820-ISSE User Manual
5-
Native Mode Operation [Auto]
Allows you to choose the native mode for ATA.
Configuration options: [Auto] [Serial ATA]
The above item appears only when the SATA Controller Mode Option is set to
[Compatible]
Serial ATA [Enabled]
Allows you to enable or disable the Serial ATA function.
Configuration options: [Disabled] [Enabled]
SATA Controller Mode Option [Enhanced]
Allows selection of the Serial ATA operation mode depending on the operating
system (OS) that you installed. When you set this item to Enhanced Mode,
Serial ATA and Parallel ATA devices are auto‑detected and placed in native
IDE mode. Set to Enhanced Mode if you are using native OS, such as
Windows® 2000/XP. When you set this item to Compatible Mode, Serial ATA
and Parallel ATA devices are auto‑detected and placed in legacy mode. Set
this item to [Compatible] if you are using legacy OS, e.g. Windows ME/98/NT,
MS-DOS. Configuration options: [Compatible] [Enhanced]
The following items appear only if you set the SATA Controller Mode Option item
to [Enhanced].
SATA RAID Enable [Disabled]
Allows you to enable or disable the Serial ATA RAID function.
Configuration options: [Disabled] [Enabled]
SATA AHCI Enable [Disabled]
Allows you to enable or disable the Serial ATA AHCI function.
Configuration options: [Disabled] [Enabled]
5-10
•
AHCI mode item will support only under Windows environment.
•
Due to the driver limitation, you will not find any SATA driver if you install
Fedora core 4.
Chapter 5: BIOS setup
5.3.5
IDE Channel 0 Master/Slave
PhoenixBIOS Setup Utility
Main
IDE Channel 0 Master
Type:
[Auto]
Multi-Sector Transfers
LBA Mode Control
32-Bit I/O
Transfer Mode
Ultra DMA Mode
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
Item Specific Help
[None]
[Disabled]
[Disabled]
[Disabled]
[Standard]
[Disabled]
-/+: Change Value
Enter: Select SubMenu
Auto = Autotyping
None = Disabling drive
ATAPI Removable = ATAPI
media (e.g., LS120,
USB Floppy, USB Zip)
CD-ROM = CD-ROM drive
IDE Removable = IDE
removable media (e.g.,
IDE Zip drive)
Other ATAPI = Other
ATAPI media
User = You supply the
hard disk drive type
F5: Setup Defaults
F10: Save and Exit
Type [Auto]
Selects the type of IDE drive. Setting to Auto allows automatic selection of the
appropriate IDE device type. Select [CD-ROM] if you are specifically configuring a
CD-ROM drive. Select [ATAPI Removable] if your device is either a ZIP, or LS-120
drive. Select [User] to manually enter the parameters of the device.
Configuration options: [Auto] [User] [Other ATAPI] [IDE Removable] [CD‑ROM]
[ATAPI Removable] [None]
•
Except for 32-Bit I/O item, the following items become user-configurable
when the Type item is not set to [Auto].
•
Suggest you to keep the default setting of this item [Auto].
•
For items that have no sub-menu, you have to use -/+ to change the values.
Multi-Sector Transfers [Disabled]
Enables or disables data multi-sectors transfers. When set to 2~16 Sectors, the
data transfer from and to the device occurs multiple sectors at a time if the device
supports multi-sector transfer feature. When set to [Disabled], the data transfer
from and to the device occurs one sector at a time.
Configuration options: [Disabled] [2 Sectors] [4 Sectors] [8 Sectors] [16 Sectors]
LBA Mode Control [Disabled]
Enables or disables the LBA mode. Setting to Enabled enables the LBA mode if the
device supports this mode, and if the device was not previously formatted with LBA
mode disabled. Configuration options: [Disabled] [Enabled]
32-Bit I/O [Disabled]
Enables or disables 32-bit data transfer.
Configuration options: [Disabled] [Enabled]
HPC-2820-ISSE User Manual
5-11
Transfer Mode [Stadard]
Allows you to select the mothod for the data transferring if the hard disk supports
this feature.
Configuration options: [Standard] [Fast PIO 1] [Fast PIO 2] [Fast PIO 3] [Fast PIO 4]
[FPIO 3 / DMA 1] [FPIO 4 / DMA2]
Ultra DMA Mode [Disabled]
When this item is set to [Mode 0-5], the UDMA capability allows improved transfer
speeds and data integrity for supported IDE devices.
Configuration options: [Disabled] [Mode 0] [Mode 1] [Mode 2] [Mode 3] [Mode 4]
[Mode 5]
5.3.6
SATA Port 1/2/3/4
PhoenixBIOS Setup Utility
Main
SATA Port 1
[None]
Type:
[Auto]
Multi-Sector Transfers
LBA Mode Control
32-Bit I/O
Transfer Mode
Ultra DMA Mode
[Disabled]
[Disabled]
[Disabled]
[Standard]
[Disabled]
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
Auto = Autotyping
None = Disabling drive
ATAPI Removable = ATAPI
media (e.g., LS120, USB
Floppy, USB Zip)
CD-ROM = CD-ROM drive
IDE Removable = IDE
removable
media
(e.g., IDE Zip drive)
Other ATAPI = Other
ATAPI media
User = You supply the
hard disk drive type
F5: Setup Defaults
F10: Save and Exit
Type [Auto]
Selects the type of IDE drive. Setting to Auto allows automatic selection of the
appropriate IDE device type. Select [CD-ROM] if you are specifically configuring a
CD-ROM drive. Select [ATAPI Removable] if your device is either a ZIP, LS-120,
or MO drive. Select [User] to manually enter the parameters of the device.
Configuration options: [Auto] [User] [Other ATAPI] [IDE Removable] [CD‑ROM]
[ATAPI Removable]
5-12
•
Except for 32-Bit I/O item, the following items become user-configurable when
the Type item is not set to [Auto].
•
For items that have no sub-menu, you have to use -/+ to change the
values.
Chapter 5: BIOS setup
Multi-Sector Transfers [Disabled]
Enables or disables data multi-sectors transfers. When set to 2~16 Sectors, the
data transfer from and to the device occurs multiple sectors at a time if the device
supports multi-sector transfer feature. When set to [Disabled], the data transfer
from and to the device occurs one sector at a time.
Configuration options: [Disabled] [2 Sectors] [4 Sectors] [8 Sectors] [16 Sectors]
LBA Mode Control [Disabled]
Enables or disables the LBA mode. Setting to Enabled enables the LBA mode if the
device supports this mode, and if the device was not previously formatted with LBA
mode disabled. Configuration options: [Disabled] [Enabled]
32-Bit I/O [Disabled]
Enables or disables 32-bit data transfer.
Configuration options: [Disabled] [Enabled]
Transfer Mode [Stadard]
Allows you to select the mothod for the data transferring if the hard disk supports
this feature.
Configuration options: [Standard] [Fast PIO 1] [Fast PIO 2] [Fast PIO 3] [Fast PIO 4]
[FPIO 3 / DMA 1] [FPIO 4 / DMA2]
Ultra DMA Mode [Disabled]
When this item is set to [Mode 0-5], the UDMA capability allows improved transfer
speeds and data integrity for supported IDE devices.
Configuration options: [Disabled] [Mode 0] [Mode 1] [Mode 2] [Mode 3] [Mode 4]
[Mode 5]
HPC-2820-ISSE User Manual
5-13
5.3.7
System Information
This menu gives you an overview of the general system specifications. The BIOS
automatically detects the items in this menu.
PhoenixBIOS Setup Utility
Main
System Information
Model Name
Model ID
HPC-2820-ISSE BIOS
Version
Date
Item Specific Help
DSBF-D12/SAS
8041A0
The detailed
information for CPUs
1000.007
09/06/2006
Processor Information
System Memory Information
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
The items in this menu are non-user configurable.
5-14
Chapter 5: BIOS setup
Processor Information
Displays the auto-detected CPU specification.
PhoenixBIOS Setup Utility
Main
Processor Information
*** CPU1 :
Brand
Intel(R) Xeon(TM) CPU 2.83GHz
Speed
2.800GHz
Ratio
Actual 7 Max 7
Cache
L1/32 KB L2/4096 KB
ID/uCode 0F64h/02h
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
All items on this menu
cannot be modified in
user mode. If any
items require changes,
please consult your
system Supervisor.
F5: Setup Defaults
F10: Save and Exit
System Memory Information
Displays the auto-detected system memory information.
PhoenixBIOS Setup Utility
Main
System Memory Information
Speed
: DDR2 533
Total Memory: 1024MB
DIMM_00-- 1024MB, AMB Temperature: 57
DIMM_01-- None
DIMM_02-- None
DIMM_10-- None
DIMM_11-- None
DIMM_12-- None
DIMM_20-- None
DIMM_21-- None
DIMM_22-- None
DIMM_30-- None
DIMM_31-- None
DIMM_32-- None
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
HPC-2820-ISSE User Manual
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
All items on this menu
cannot be modified in
user mode. If any
items require changes,
please consult your
system Supervisor.
F5: Setup Defaults
F10: Save and Exit
5-15
5.4
Advanced menu
The Advanced menu items allow you to change the settings for the CPU and other
system devices.
Take caution when changing the settings of the Advanced menu items. Incorrect
field values can cause the system to malfunction.
Main
Advanced
Server
PhoenixBIOS Setup Utility
Security
Boot
Exit
WARNING:Setting wrong value in below sections may
cause system to malfunction.
Advanced Processor Options
Chipset Configuration
PCI Configuration
ICH USB Control Sub-Menu
Peripheral Devices Configuration
ACPI Configuration
Power On Configuration
Hardware Monitor
F1:Help
ESC: Exit
5.4.1
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
Options for CPU
F5: Setup Defaults
F10: Save and Exit
Advanced Processor Options
The following screen appears when you install an Intel® 5000 series CPU.
Advanced
Advanced Processor Options
Multiprocessor Specification
Frequency Ratio
Hyperthreading:
[1.4]
[Default]
[Enabled]
Intel(R) Virtualization Technology
Machine Checking [Enabled]
[Enabled]
Fast String operations
Compatible FPU Code
Split Lock operations
C1 Enhanced Mode
No Execute Mode Mem Protection
Adjacent Cache Line Prefetch
Set Max Ext CPUID = 3
[Enabled]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Disabled]
F1:Help
ESC: Exit
5-16
PhoenixBIOS Setup Utility
↑↓ :Select Item
→← :Select Menu
Item Specific Help
-/+: Change Value
Enter: Select SubMenu
Configures the
MP Specification
revision level. Some
operating systems
will require 1.1
for compatibility
reasons.
F5: Setup Defaults
F10: Save and Exit
Chapter 5: BIOS setup
Multiprocessor Specification [1.4]
Allows you to configure the MP Specification revision level.
Configuration options: [1.1] [1.4]
Frequency Ratio [Default]
Allows you to select the processor frequency ratio.
Configuration options: [Default] [X 12]
Hyperthreading [Enabled]
Allows you to enable or disable the Intel® Hyper-Threading Technology feature.
Configuration options: [Disabled] [Enabled]
Intel(R) Virtualization Technology [Enabled]
Configuration options: [Disabled] [Enabled]
*Machine Checking [Enabled]
Configuration options: [Disabled] [Enabled]
*Fast String Operations [Enabled]
Configuration options: [Disabled] [Enabled]
*Compatible FPU Code [Disabled]
Configuration options: [Disabled] [Enabled]
*Split Lock operations [Enabled]
Configuration options: [Disabled] [Enabled]
C1 Enhanced Mode [Enabled]
Allows you to enable or disable C1E mode. In C1E mode, the CPU power
consumption is lower when idle. Configuration options: [Disabled] [Enabled]
No Execute Mode Mem Protection [Enabled]
Configuration options: [Disabled] [Enabled]
Set Max Ext CPUID = 3 [Disabled]
Enable this item to boot legacy operating systems that cannot support CPUs with
extended CPUID functions. Configuration options: [Disabled] [Enabled]
Adjacent Cache Line Prefetch [Enabled]
Configuration options: [Disabled] [Enabled]
Items with * mark are for technical personnel to debug only.
HPC-2820-ISSE User Manual
5-17
Echo TPR [Disabled]
Configuration options: [Disabled] [Enabled]
Scroll down to display the following items, which appear in both Intel® 5000, 5100,
and 5300 series CPU.
Item Specific Help
Advanced Processor Options
Discrete MTRR Allocation
Intel EIST support:
F1:Help
ESC: Exit
[Disabled]
[Disabled]
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
Discrete MTRR Allocation [Disabled]
Configuration options: [Disabled] [Enabled]
Intel EIST support [Disabled]
Enables or disables EIST support. When enabled, this item allows the CPU P state
to dynamically change based on system loading.
Configuration options: [Disabled] [Enabled]
The following screen appears when you install an Intel® 5100 and 5300 series
CPU. Refer to page 21 for the description of items that are in common with
Intel® 5000 series CPU screen.
Advanced
PhoenixBIOS Setup Utility
Advanced Processor Options
Multiprocessor Specification
Numbers of Stop Grant
[1.4]
[Per Core]
Intel(R) Virtualization Technology
Machine Checking [Enabled]
[Enabled]
Fast String Operations Compatible FPU Code Split Lock operations Thermal Management 2
C1 Enhanced Mode No Execute Mode Mem Protection
Adjacent Cache Line Prefetch
Set Max Ext CPUID = 3
Echo TPR
[Enabled]
[Disabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Disabled]
[Disabled]
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
Configures the MP
Specification revision
level. Some operating
systems will require
1.1 for compatibility
reasons.
F5: Setup Defaults
F10: Save and Exit
Numbers of Stop Grant [Per Core]
Configuration options: [Per Core] [Single]
Thermal Management 2 [Enabled]
Configuration options: [Disabled] [Enabled]
5-18
Chapter 5: BIOS setup
5.4.2
Chipset Configuration
This menu shows the chipset configuration settings. Select an item then press
<Enter> to display a pop-up menu with the configuration options.
PhoenixBIOS Setup Utility
Advanced
Chipset Configuration
Crystal Beach Configure Enable
SERR Signal Condition
Demand Scrub Enable
Patrol Scrub Enable
[Enabled]
[Single Bit]
[Enabled]
[Enabled]
4GB PCI Hole Granularity
Memory Branch Mode
Branch 0 Rank Interleave
Branch 0 Rank Sparing
Branch 1 Rank Interleave
Branch 1 Rank Sparing
Enhanced x8 Detection
Force ITK Config Clocking
[256 MB]
[Interleave]
[4:1]
[Disabled]
[4:1]
[Disabled]
[Enabled]
[Disabled]
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
Scroll down to display the following items:
Item Specific Help
Advanced Processor Options
FBDIMM(s) Thermal Throttling
Open Loop Type
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
[Open Loop]
[Best Performan]
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
Crystal Beach Configure Enable [Enabled]
Allows you to enable or disable the Configuration/Memory mapped accesses
to the Crystal Beach Configuration space located in Device 8, Fn 0, and Fn 1.
Configuration options: [Disabled] [Enabled]
HPC-2820-ISSE User Manual
5-19
SERR Signal Condition [Single Bit]
Allows you to select the ECC error that the SERR# asserts.
Configuration options: [None] [Single Bit] [Multiple Bit] [Both]
Demand Scrub Enable [Enabled]
Enables or disables the Demand Scrubbing.
Configuration options: [Disabled] [Enabled]
Patrol Scrub Enable [Enabled]
Enables or disables the Patrol Scrubbing.
Configuration options: [Disabled] [Enabled]
4GB PCI Hole Granularity [256 MB]
Allows you to select the granularity of the PCI hole for PCI resource.
Configuration options: [256 MB] [512 MB] [1.0 GB] [2.0 GB]
Memory Branch Mode [Interleave]
Allows you to select the memory branch mode.
Configuration options: [Sequential] [Interleave] [Mirror] [Single channel 0]
Branch 0 Rank Interleave [4:1]
Allows you to select the Branch 0 Rank Interleave.
Configuration options: [1:1] [2:1] [4:1]
Branch 0 Rank Sparing [Disabled]
Allows you to enable or disable the Branch 0 rank/DIMM Sparing feature.
Configuration options: [Disabled] [Enabled]
Branch 1 Rank Interleave [4:1]
Allows you to select the Branch 1 Rank Interleave.
Configuration options: [1:1] [2:1] [4:1]
Branch 1 Rank Sparing [Disabled]
Allows you to enable or disable the Branch 1 rank/DIMM Sparing feature.
Configuration options: [Disabled] [Enabled]
Enhanced x8 Detection [Enabled]
Allows you to enable or disable the enhanced x8 DRAM UC error detection.
Configuration options: [Disabled] [Enabled]
5-20
Chapter 5: BIOS setup
Force ITK Config Clocking [Disabled]
Allows you to enable or disable the FBD configuration for ITK test suite.
Configuration options: [Disabled] [Enabled]
FBDIMM(s) Thermal Throttling [Open Loop]
Allows you to disable or set the thermal throttling control.
Configuration options: [Open Loop] [Closed Loop] [MemCool Fan] [Disabled]
Set this item to [MemCool Fan] for a better fan management.
Open Loop Type [Best Performance]
Allows you to select the Open Loop Type.
Configuration options: [Best Performance] [Best Acoustic] [User Define]
The following items appear when you set the Open Loop Type to [User Define].
Environment Temperature [25 ºC]
Allows you to select the Environment Temperature value.
Configuration options: [20 ºC] ~ [40 ºC]
Temperature Rise [25 ºC]
Allows you to select the Temperature Rise value.
Configuration options: [10 ºC] ~ [30 ºC]
FBDIMM(s) Air Flow [2.0]
Allows yout to select the Air Flow value.
Configuration options: [1.0] [1.5] ~ [5.0]
HPC-2820-ISSE User manual
5-21
5.4.3
PCI Configuration
This menu shows the PCI configuration settings. Select an item then press <Enter>
to display the configuration options.
PhoenixBIOS Setup Utility
Advanced
PCI Configuration
Reset Configuration Data
Plug & Play OS
Palette Snooping
PCI
PCI
PCI
PCI
PCI
PCI
Device,
Device,
Device,
Device,
Device,
Device,
F1:Help
ESC: Exit
Slot
Slot
Slot
Slot
Slot
Slot
Item Specific Help
[No]
[No]
[Disabled]
#1
#2
#3
#4
#5
#6
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Select ‘Yes’ if you
want to clear the
Extended System
Configuration Data
(ESCD) area.
F5: Setup Defaults
F10: Save and Exit
Reset Configuration Data [No]
This item allows you to clear the Extended System Configuration Data (ESCD)
area. Configuration options: [No] [Yes]
Plug & Play O/S [No]
When set to [No], BIOS configures all the devices in the system. When set to
[Yes] and if you install a Plug and Play operating system, the operating system
configures the Plug and Play devices not required for boot.
Configuration options: [No] [Yes]
Palette Snooping [Disabled]
When set to [Enabled], the palette snooping feature informs the PCI devices that
an ISA graphics device is installed in the system so that the latter can function
correctly. Configuration options: [Disabled] [Enabled]
5-22
Chapter 5: BIOS setup
PCI Device, Slot #1 ~ 6
Allows you to configure the specific PCI devices.
PhoenixBIOS Setup Utility
Advanced
PCI Device, Slot #1
Option ROM Scan:
F1:Help
ESC: Exit
Item Specific Help
[Enabled]
↑↓ :Select Item
→← :Select Menu
Initialize device
expansion ROM
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
Option ROM Scan [Enabled]
Allows you to enable or disable the device expansion ROM.
Configuration options: [Enabled] [Disabled]
HPC-2820-ISSE User manual
5-23
5.4.4
ICH USB Control Sub-Menu
The items in this menu allow you to display the USB configuration settings. Select
an item then press <Enter> to display the configuration options.
Advanced
PhoenixBIOS Setup Utility
ICH USB Control Sub-Menu
USB Function
[Enabled]
USB 2.0 Controller
Legacy USB Support:
[Enabled]
[Enabled]
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
Enable USB host
controller.
F5: Setup Defaults
F10: Save and Exit
USB Function [Enabled]
Allows you to enable the USB host controller.
Configuration options: [Disabled] [Enabled]
The following items appear only if you enable the USB Function item.
USB 2.0 Controller [Enabled]
Allows you to enable or disable the USB 2.0 controller. Setting this item to [Enabled]
allows the built-in high speed USB support in the BIOS to turn on automatically
when you install high speed USB devices.
Configuration options: [Disabled] [Enabled]
Legacy USB Support [Enabled]
Allows you to enable or disable support for USB devices on legacy operating
systems (OS). Setting to [Enabled] allows the system to detect the presence of
USB devices at startup. If detected, the USB controller legacy mode is enabled. if
no USB device is detected, the legacy USB support is disabled.
Configuration options: [Disabled] [Enabled]
5-24
Chapter 5: BIOS setup
5.4.5
Peripheral Devices Configuration
This menu shows the peripheral devices configuration settings. Select an item
then press <Enter> to display the configuration options.
Advanced
PhoenixBIOS Setup Utility
Peripheral Devices Configuration
COM1 Port:
Base I/O address:
Interrupt:
COM2 Port:
Mode:
Base I/O address:
Interrupt:
Parallel port:
Base I/O address:
Interrupt:
Mode:
DMA channel
Floppy disk controller
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
[Enabled]
[3F8]
[IRQ 4]
[Enabled]
[Normal]
[2F8]
[IRQ 3]
[Enabled]
[378]
[IRQ 7]
[ECP]
[DMA 3]
[Enabled]
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
Confugure serial port
A using options:
[Disabled]
No configuration
[Enabled]
User configuration
[Auto]
BIOS or OS chooses
configuration
(OS Controlled)
Displayed when
controlled bt OS
F5: Setup Defaults
F10: Save and Exit
COM1 Port [Enabled]
Allows you to configure COM1 port.
Configuration options: [Disabled] [Enabled] [Auto]
Base I/O address [3F8]
Allows you to select the base I/O address for COM1 port.
Configuration options: [3F8] [2F8] [3E8] [2E8]
Interrupt [IRQ 4]
Allows you to set the interrupt for COM1 port
Configuration options: [IRQ 3] [IRQ 4]
COM2 Port [Enabled]
Allows you to configure COM2 port.
Configuration options: [Disabled] [Enabled] [Auto]
Mode [Normal]
Allows you to set the mode for COM2 port.
Configuration options: [Normal] [IR] [ASK-IR]
Base I/O address [2F8]
Allows you to select the base I/O address for COM2 port.
Configuration options: [3F8] [2F8] [3E8] [2E8]
Interrupt [IRQ 3]
Allows you to set the interrupt for COM2 port.
Configuration options: [IRQ 3] [IRQ 4]
HPC-2820-ISSE User manual
5-25
Parallel port [Enabled]
Allows you to configure the parallel port.
Configuration options: [Disabled] [Enabled] [Auto]
Base I/O address [378]
Allows you to select the base I/O address for the parallel port.
Configuration options: [378] [278] [3BC]
Interrupt [IRQ 7]
Allows you to set the interrupt for the parallel port.
Configuration options: [IRQ 5] [IRQ 7]
Mode [ECP]
Allows you to set the mode for the parallel port.
Configuration options: [Output only] [Bi-directional] [EPP] [ECP]
DMA channel [DMA 3]
Allows you to set the DMA channel for the parallel port.
Configuration options: [DMA 1] [DMA 3]
Floppy disk controller [Enabled]
Allows you to configure the floppy disk controller.
Configuration options: [Disabled] [Enabled] [Auto]
5-26
Chapter 5: BIOS setup
5.4.6
ACPI Configuration
This menu shows the Advanced Configuration and Power Interface (ACPI)
configuration settings. Select an item then press <Enter> to display the
configuration options.
PhoenixBIOS Setup Utility
Advanced
ACPI Configuration
ACPI Version Features
Headless Mode
ACPI EMS Support
F1:Help
ESC: Exit
Item Specific Help
[ACPI v1.0]
[Disabled]
[Disabled]
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Enable RSDP pointers
to 64-bit Fixed System
Description Tables.
F5: Setup Defaults
F10: Save and Exit
ACPI Version Features [ACPI v1.0]
Allows you to enable RSDP pointers to 64-bit fixed system description tables.
Configuration options: [ACPI v1.0] [ACPI v2.0] [ACPI v3.0]
Headless Mode [Disabled]
Allows you to enable or disable the headless operation mode through ACPI.
Configuration options: [Disabled] [Enabled]
ACPI EMS Support [Disabled]
Allows you to enable or disable the ACPI EMS support.
Configuration options: [Disabled] [Enabled]
HPC-2820-ISSE User manual
5-27
5.4.7
Power On Configuration
This menu shows the power configuration settings. Select an item then press
<Enter> to display the configuration options.
PhoenixBIOS Setup Utility
Advanced
Power On Configuration
Restore on AC Power Loss
[Last State]
Power On
Power On
Power On
Power-On
[Disabled]
[Disabled]
[Disabled]
[Disabled]
F1:Help
ESC: Exit
By
By
By
By
PS/2 Keyboard
PS/2 Mouse
PME#
RTC Alarm
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
Configures the system state
after recovering from
power failure.
F5: Setup Defaults
F10: Save and Exit
Restore on AC Power Loss [Last State]
When set to [Power Off], the system goes into “off state” after an AC power
interruption. When set to [Power On], the system turns on automatically after a
power interruption. When set to [Last State], the system goes into whatever was
the system state (on or off) before the power interruption.
Configuration options: [Power Off] [Power On] [Last State]
Power On By PS/2 Keyboard [Disabled]
Allows you to use specific keys on the PS/2 keyboard to turn on the system. This
feature requires an ATX power supply that provides at least 1A on the +5VSB lead.
Configuration options: [Enabled] [Disabled]
Power On By PS/2 Mouse [Disabled]
When set to [Enabled], this parameter allows you to use the PS/2 mouse to turn on
the system. This feature requires an ATX power supply that provides at least 1A on
the +5VSB lead. Configuration options: [Enabled] [Disabled]
Power On By PME# [Disabled]
Allows you to enable or disable the PME and onboard LAN to generate a wake-up
event. Configuration options: [Disabled] [Enabled]
Power On By RTC Alarm [Disabled]
Allows you to enable or disable RTC to generate a wake-up event.
Configuration options: [Disabled] [Enabled]
5-28
Chapter 5: BIOS setup
The following items appear only if you enable the Power On By RTC Alarm
item.
RTC Alarm Date [0]
To set the date of alarm, highlight this item and press <Enter> to display a date
chart. Press <+> or <-> to change scroll through the options, then press <Enter>
when done. The default setting [0] is equivalent to everyday alarm.
Configuration options: [0] [1] ~ [31]
RTC Alarm Date [00 : 00 : 00]
To set the time of alarm:
1. Press <+> or <-> to set the desired value.
2. Press <Tab> to move to the next field.
3.
Press <Enter> when done.
5.4.8
Hardware Monitor
This menu shows the hardware monitor configuration settings. Select an item then
press <Enter> to display the configuration options.
The following screens appear when you install Intel® 5000 series CPU.
PhoenixBIOS Setup Utility
Advanced
Hardware Monitor
CPU1 Domain 0 Temperature
CPU1 Domain 1 Temperature
CPU2 Domain 0 Temperature
CPU2 Domain 1 Temperature
SYSTEM1 Temperature
SYSTEM2 Temperature
CPU_FAN1 Speed
CPU_FAN2 Speed
FRN_FAN1 Speed
FRN_FAN2 Speed
FRN_FAN3 Speed
FRN_FAN4 Speed
REAR_FAN1 Speed
REAR_FAN2 Speed
Smart Fan Control
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
HPC-2820-ISSE User manual
39oC/102oF
29oC/84oF
0oC/32oF
0oC/32oF
39oC/102oF
29oC/84oF
2925 RPM
N/A
N/A
N/A
N/A
N/A
N/A
N/A
[Smart Fan II]
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
To select the fan speed
control model.
F5: Setup Defaults
F10: Save and Exit
5-29
Scroll down to display more items:
Advanced
PhoenixBIOS Setup Utility
Hardware Monitor
Item Specific Help
CPU1 Domain 0 Target Temperature
CPU1 Domain 1 Target Temperature
CPU2 Domain 0 Target Temperature
CPU2 Domain 1 Target Temperature
SYSTEM1 Target Temperature
SYSTEM2 Target Temperature
[72ºC]
[72ºC]
[72ºC]
[72ºC]
[60ºC]
[60ºC]
FBD_FAN1 Speed
VCORE0 Voltage
VCORE1 Voltage
VTT
+1.5V +1.8V +3V
+12V
+5V +5VSB VBAT N/A
1.25 V
1.25 V
1.21 V
1.56 V
1.79 V
3.28 V
11.91 V
4.87 V
4.96 V
3.10 V
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Full fan speed will
be started when the
temperature reaches the
selected target value.
F5: Setup Defaults
F10: Save and Exit
CPU1/2 Domain 0/1 Temperature, SYSTEM1/2 Temperature,
CPU_FAN1/2 Speed, FRN_FAN1/2/3/4 Speed, REAR_FAN1/2 Speed
These fields show the auto-detected values and are not user-configurable. If no fan
is installed, the field shows 0 RPM.
Smart Fan Control [Smart Fan II]
Allows you to disable or configure the Smart Fan feature.
Configuration options: [Disabled] [Smart Fan] [Smart Fan II]
CPU1/2 Domain 0/1 Target Temperature (CPU1/2 Target Temperature)
Allows you to set the target CPU temperature at which the CPU fan will run at full
speed. Configuration options: [44ºC] ~ [66ºC]
SYSTEM1/2 Target Temperature
Allows you to set the target sytem temperature at which the system fan will start
running if the fan is not yet turned on.
Configuration options: [39ºC] ~ [60ºC]
FBD_FAN1/2 Speed, VCORE0/1 Voltage, VTT, +1.5V, +1.8V, +3V, +12V,
+5V, +5VSB, VBAT
These fields show the auto-detected values and are not user-configurable.
5-30
Chapter 5: BIOS setup
The following screens appear when you install Intel® 5100 and 5300 series
CPU.
PhoenixBIOS Setup Utility
Advanced
Hardware Monitor
39oC/102oF
29oC/84oF
39oC/102oF
29oC/84oF
2925 RPM
N/A
N/A
N/A
N/A
N/A
N/A
N/A
[Smart Fan II]
[00 ºC]
[00 ºC]
CPU1 Temperature CPU2 Temperature SYSTEM1 Temperature
SYSTEM2 Temperature
CPU_FAN1 Speed
CPU_FAN2 Speed
FRN_FAN1 Speed
FRN_FAN2 Speed
FRN_FAN3 Speed
FRN_FAN4 Speed
REAR_FAN1 Speed
REAR_FAN2 Speed
Smart Fan Control
CPU1 Target Temperature
CPU2 Target Temperature
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
To select the fan speed
control model.
F5: Setup Defaults
F10: Save and Exit
Scroll down to display more items:
PhoenixBIOS Setup Utility
Advanced
Hardware Monitor
SYSTEM1 Target Temperature
SYSTEM2 Target Temperature
[050]
[050]
FBD_FAN1 Speed
FBD_FAN2 Speed
VCORE0 Voltage
VCORE1 Voltage
VTT
+1.5V +1.8V +3V
+12V
+5V +5VSB VBAT N/A
N/A
1.25 V
1.25 V
1.21 V
1.56 V
1.79 V
3.28 V
11.91 V
4.87 V
4.96 V
3.10 V
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
Full fan speed will
be started when the
temperature reaches the
selected target value.
F5: Setup Defaults
F10: Save and Exit
CPU1/2 Temperature, SYSTEM1/2 Temperature, CPU_FAN1/2 Speed,
FRN_FAN1/2/3/4 Speed, REAR_FAN1/2 Speed
These fields show the auto-detected values and are not user-configurable. If no fan
is installed, the field shows 0 RPM.
Smart Fan Control [Smart Fan II]
Allows you to disable or configure the Smart Fan feature.
Configuration options: [Disabled] [Smart Fan] [Smart Fan II]
CPU1/2 Target Temperature
Allows you to set the target CPU temperature at which the CPU fan will run at full
speed. Configuration options: [44ºC] ~ [66ºC]
HPC-2820-ISSE User manual
5-31
SYSTEM1/2 Target Temperature
Allows you to set the target sytem temperature at which the system fan will start
running if the fan is not yet turned on.
Configuration options: [39ºC] ~ [60ºC]
FBD_FAN1/2 Speed, VCORE0/1 Voltage, VTT, +1.5V, +1.8V, +3V, +12V,
+5V, +5VSB, VBAT
These fields show the auto-detected values and are not user-configurable.
5.5
Server menu
This Server menu items allow you to customize the server features.
Main
Advanced
Server
PhoenixBIOS Setup Utility
Security
Boot
Exit
Console Redirection
DMI Event Logging
F1:Help
ESC: Exit
5.5.1
Main
Additional setup
menus to configure
console.
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
Console Redirection
Advanced
Server
Console Redirection
Com Port Address
F1:Help
ESC: Exit
5-32
Item Specific Help
PhoenixBIOS Setup Utility
Security
Boot
Exit
↑↓ :Select Item
→← :Select Menu
Item Specific Help
[Disabled]
-/+: Change Value
Enter: Select SubMenu
If enabled, it will
use a port on the
motherboard.
F5: Setup Defaults
F10: Save and Exit
Chapter 5: BIOS setup
Com Port Address [Disabled]
Allows you to disable or select the COM port to use.
Configuration options: [Disabled] [Onboard COM1 port] [Onboard COM2 port]
The following items appear only if you set the Com Port Address item to
[Onboard COM1 port] or [Onboard COM2 port].
Baud Rate [57.6K]
Allows you to enable the specified baud rate.
Configuration options: [300] [1200] [2400] [9600] [19.2K] [38.4K] [57.6K] [115.2K]
Console Type [VT-UTF8]
Allows you to enable the specified console type.
Configuration options: [VT100] [VT100, 8bit] [PC-ANSI, 7bit] [PC ANSI] [VT100+]
[VT-UTF8] [ASCII]
Flow Control [None]
Allows you to select the flow control for console redirection.
Configuration options: [None] [XON/XOFF] [CTS/RTS]
Console connection [Direct]
Allows you to select the console connection. [Direct] indicates that the console is
connected directed to the system. [Via modem] indicates that a modem is used to
connect. Configuration options: [Direct] [Via modem]
Continue C.R. after POST [Off]
Set this item to [On] if you want console redirection to continue after the operating
system has loaded. Configuration options: [Off] [On]
# of video pages to support [1]
Allows you to set the number of video pages to allocate for console redirection
when the video hardware is not available. Press <-> or <+> to set the value, or
enter the value using the numeric keypad. Configuration options: [1] ~ [8]
HPC-2820-ISSE User manual
5-33
5.5.2
Main
DMI Event Logging
Advanced
Server
PhoenixBIOS Setup Utility
Security
Boot
Exit
DMI Event Logging
Event log validity
Event log capacity
Valid
Space Available
View DMI event log
[Enter]
Event Logging
ECC Event Logging
[Enabled]
[Enabled]
Mark DMI events as read
Clear all DMI event logs
[Enter]
[No]
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
View the contents of the
DMI event log.
F5: Setup Defaults
F10: Save and Exit
Event log validity, Event log capacity
Displays the auto-detected system information.
View DMI event log [Enter]
Press <Enter> to view the contents of the DMI event log.
Event Logging [Enabled]
Enables or disables to allows logging of DMI events.
Configuration options: [Disabled] [Enabled]
ECC Event Logging [Enabled]
Enables or disables to allows logging of ECC events.
Configuration options: [Disabled] [Enabled]
Mark DMI events as read [Enter]
Press <Enter> to mark all DMI events in the event log as read.
Clear all DMI event logs [No]
Allows you to keep or clear the DMI event log after rebooting.
Configuration options: [No] [Yes]
5-34
Chapter 5: BIOS setup
5.6
Main
F1
ESC
Security menu
Advanced
Server
PhoenixBIOS Setup Utility
Security
Boot
Exit
Supervisor Password Is:
User Password Is:
Clear
Clear
Set Supervisor Password
Set User Password
Password Check
Password Lock Mode
Removable Device Boot
Flash Write
[Enter]
[Enter]
[Setup]
[Disabled]
[Enabled]
[Enabled]
Help
Exit
↑↓
→←
Select Item
Select Menu
-/+
Enter
Item Specific Help
Supervisor Password
controls access to the
setup utility.
Change Values
Select
Sub-Menu
F9
F10
Setup Defaults
Save and Exit
Supervisor Password Is [Clear].
User Password Is [Clear]
These fields allow you to set passwords:
To set a password:
1. Select an item then press <Enter>.
2.
Type in a password using a combination of a maximum of eight (8) alphanumeric characters, then press <Enter>.
3. When prompted, confirm the password by typing the exact characters again,
then press <Enter>. The password field setting is changed to Set.
To clear the password:
1.
Select the item Set Supervisor Password or Set User Password, depending
on which password you want to clear. Press <Enter>.
The following message appears:
Main
Advanced
Server
PhoenixBIOS Setup Utility
Security
Boot
Exit
Supervisor Password Is:
User Password Is:
Clear
Clear
Set Supervisor Password
[Enter]
Set User Password
[Enter]
Password Check
[Setup]
Set Supervisor
Password Lock Mode
[Disabled] Password
Removable Device Boot
[Enabled]
Enter
Current
Password
[
Flash Write
[Enabled]
Enter New Password [
Confirm New Password
[
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
HPC-2820-ISSE User manual
-/+: Change Value
Enter: Select SubMenu
Item Specific Help
Supervisor Password
controls access to the
setup utility.
]
]
]
F5: Setup Defaults
F10: Save and Exit
5-35
2.
3.
4.
5.
In the Enter current password field, type in your current password. Press
<Enter>.
The cursor moves to the next field, Enter new password.
Press <Enter>. Do not type anything in this field.
The cursor moves to the next field, Confirm new password.
Press <Enter>. Do not type anything in this field.
When the confirmation message “Password has been changed” appears,
press <Enter>.
The display returns to the Security menu. Note that the password field on top
is changed to Clear.
A note about passwords
The Supervisor password is required to enter the BIOS Setup program
preventing unauthorized access. The User password is required to boot the
system preventing unauthorized use.
Forgot your password?
If you forget your password, you can clear it by erasing the CMOS Real Time
Clock (RTC) RAM. The RAM data containing the password information is
powered by the onboard button cell battery. If you need to erase the CMOS
RAM, refer to section “2.6 Jumpers” for instructions.
Password Check [Setup]
This field requires you to enter the password before entering the BIOS setup or the
system. Select [Setup] to require the password before entering the BIOS Setup.
Select [System] to require the password before entering the system.
Configuration options: [Setup] [Always]
Password Lock Mode [Enabled]
When set to [Enabled], the keyboard is locked and the user has no privilege to
launch the BIOS setup utility when installing adapter cards during option ROM
initialization. Configuration options: [Disabled] [Enabled]
Removable Device Boot [Enabled]
Allows you to enable or disable booting from a legacy floppy, USB floppy, or IDE
optical drive. Configuration options: [Disabled] [Enabled]
Flash Write [Enabled]
Set this item to [Disabled] to write-protect the BIOS flash memory.
Configuration options: [Disabled] [Enabled]
5-36
Chapter 5: BIOS setup
5.7
Main
Boot menu
Advanced
Server
PhoenixBIOS Setup Utility
Security
Boot
Exit
Boot Device Priority
Item Specific Help
Boot Features
F1:Help
ESC: Exit
5.7.1
Main
↑↓ :Select Item
→← :Select Menu
Specify the boot
priority sequence of all
boot devices.
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
Boot Device Priority
Advanced
Server
PhoenixBIOS Setup Utility
Security
Boot
Exit
Boot Device Priority
Item Specific Help
Boot priority order:
1: Legacy Floppy Drives
2: IDE 1:
3: IDE 2:
4:
5:
6:
7:
8:
Keys used to view or
configure devices: Up
and Down arrows select
a device. <+> and <->
moves the device up
or down. <f> and <r>
specifies the device as
fixed or removable.
<x> excludes or
includes the device to
boot.
<Shift + 1> enables or
disables the device.
<1 - 4> Loads default
boot sequence.
Excluded from boot order:
: PCI BEV: IBA GE Slot 0400 v1236
: PCI BEV: IBA GE Slot 0400 v1236
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
Refer to the following table for keys assigned to configure devices.
Key/s
Use this key to...
<+> / <->
move the device up or down.
<Up arrow> / <Down arrow>
select a device.
<f> / <r>
specify the device as fixed or removable.
<Shift + 1>
enable or disable the device.
<x>
<1 - 4>
HPC-2820-ISSE User manual
exclude or include the device to boot.
load default boot sequence.
5-37
5.7.2
Main
Boot Features
Advanced
Server
PhoenixBIOS Setup Utility
Security
Boot
Exit
Boot Features
Quick Boot Full Logo Display
Bootup Num-Lock
PS/2 Mouse Summary screen:
POST Errors
SETUP prompt
Interrupt 19 Capture
F1
Help
F1:Help
ESC
ESC: Exit
[Enabled]
[Enabled]
[On]
[Auto Detect]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
↑↓↑↓Select
Item
Change
Values
:Select
Item -/+ -/+:
Change
Value
→←
Menu
Select
→←Select
:Select
Menu Enter
Enter:
SelectSub-Menu
SubMenu
Item Specific Help
Allows the BIOS to
skip certain tests
while booting. This
will decrease the time
needed to boot the
system.
F9 F5:Setup
SetupDefaults
Defaults
Save
andand
Exit
F10F10:
Save
Exit
Quick Boot [Enabled]
Enabling this item allows the BIOS to skip some power on self tests (POST) while
booting to decrease the time needed to boot the system. When set to [Disabled],
BIOS performs all the POST items.
Configuration options: [Disabled] [Enabled]
Full Logo Display [Enabled]
Allows you to enable or disable the full screen logo display feature.
Configuration options: [Disabled] [Enabled]
Bootup Num-Lock [On]
Allows you to select the power-on state for the NumLock.
Configuration options: [Auto] [On] [Off]
PS/2 Mouse [Auto Detect]
Allows you to enable or disable support for PS/2 mouse.
Configuration options: [Disabled] [Enabled] [Auto Detect]
Summary screen: [Enabled]
When this item is enabled, the system configuration is displayed during POST.
Configuration options: [Disabled] [Enabled]
POST Errors [Enabled]
When set to Enabled, the system waits for the F1 key to be pressed when error
occurs. Configuration options: [Disabled] [Enabled]
5-38
Chapter 5: BIOS setup
SETUP prompt [Enabled]
When this item is set to Enabled, the system displays the message “Press DEL to
run Setup” during POST. Configuration options: [Disabled] [Enabled]
Interrupt 19 Capture [Enabled]
When set to [Enabled], this function allows the option ROMs to trap Interrupt 19.
Configuration options: [Disabled] [Enabled]
5.8
Main
Exit menu
Advanced
Server
PhoenixBIOS Setup Utility
Security
Boot
Exit
Save Changes and Exit
Discard Changes and Exit
Discard Changes
Load Setup Defaults
F1:Help
ESC: Exit
↑↓ :Select Item
→← :Select Menu
Item Specific Help
Save any changes to CMOS,
exit BIOS Setup then
reboot system.
-/+: Change Value
Enter: Select SubMenu
F5: Setup Defaults
F10: Save and Exit
Save Changes and Exit
Select this option then press <Enter>, or simply press <F10>, to save your changes
to CMOS before exiting the Setup utility.
When a confirmation window appears:
•
•
select [Yes], then press <Enter> to save and exit.
select [No], then press <Enter>, or simply press <Esc>, to cancel the command
and return to the Exit menu.
Discard Changes and Exit
Select this option then press <Enter> if you wish to exit the Setup utility without
saving your changes.
When a confirmation window appears:
•
•
select [Yes], then press <Enter> to discard your changes and exit.
select [No], then press <Enter>, or simply press <Esc>, to cancel the command
and return to the Exit menu.
HPC-2820-ISSE User manual
5-39
Discard Changes
Select this option to discard the changes that you made, and restore the previously
saved values.
When a confirmation window appears:
•
•
select [Yes], then press <Enter> to discard any changes and load the
previously saved values.
select [No], then press <Enter>, or simply press <Esc>, to cancel the command
and return to the Exit menu.
Load Setup Defaults
Select this option then press <Enter>, or simply press <F9>, to load the optimized
values for each of the Setup menu items.
When a confirmation window appears:
•
•
5-40
select [Yes], then press <Enter> to load the default values.
select [No], then press <Enter>, or simply press <Esc>, to cancel the command
and return to the Exit menu.
Chapter 5: BIOS setup
CHAPTER
RAID Configuration
6
6.1
Setting up RAID
The motherboard comes with the following RAID solutions:
•
LSI1068 PCI-X SAS controller supports SAS disk drives and RAID0, RAID1,
and RAID1E configuration.
6.1.1
RAID definitions
RAID 0 (Data striping) optimizes two identical hard disk drives to read and write
data in parallel, interleaved stacks. Two hard disks perform the same work as a
single drive but at a sustained data transfer rate, double that of a single disk alone,
thus improving data access and storage. Use of two new identical hard disk drives
is required for this setup.
RAID 1 (Data mirroring) copies and maintains an identical image of data from one
drive to a second drive. If one drive fails, the disk array management software
directs all applications to the surviving drive as it contains a complete copy of
the data in the other drive. This RAID configuration provides data protection and
increases fault tolerance to the entire system. Use two new drives or use an
existing drive and a new drive for this setup. The new drive must be of the same
size or larger than the existing drive.
RAID 1-E (Enhanced RAID 1) has a striped layout with each stripe unit having a
secondary (or alternate) copy stored on a different disk. You can use three or more
hard disk drives for this configuration.
RAID 5 stripes both data and parity information across three or more hard disk
drives. Among the advantages of RAID 5 configuration include better HDD
performance, fault tolerance, and higher storage capacity. The RAID 5 configuration
is best suited for transaction processing, relational database applications,
enterprise resource planning, and other business systems. Use a minimum of
three identical hard disk drives for this setup. Available when you install an optional
ZCR.
If you want to boot the system from a hard disk drive included in a created RAID
set, copy first the RAID driver from the support CD to a floppy disk before you
install an operating system to the selected hard disk drive.
6-
Chapter 6: RAID configuration
6.1.2
Installing hard disk drives
The motherboard supports Serial ATA for RAID set configuration. For optimal
performance, install identical drives of the same model and capacity when creating
a disk array.
To install the SATA hard disks for RAID configuration:
1.
2.
3.
Install the SATA hard disks into the drive bays following the instructions in the
system user guide.
Connect a SATA signal cable to the signal connector at the back of each drive
and to the SATA connector on the motherboard.
Connect a SATA power cable to the power connector on each drive.
6.1.3
Setting the RAID item in BIOS
You must set the RAID item in the BIOS Setup before you can create a RAID set
from SATA hard disk drives attached to the SATA connectors supported by the
Intel® 6321ESB Southbridge chip. To do this:
1.
2.
3.
4.
5.
Enter the BIOS Setup during POST.
Go to the Main Menu > IDE Configuration > S-ATA Configuration, then
press <Enter>.
Set the SATA Controller Mode Option item to [Enhanced], then press
<Enter>.
Set the SATA RAID Enable item to [Enabled].
Save your changes, then exit the BIOS Setup.
Refer to Chapter 5 for details on entering and navigating through the BIOS
Setup.
6.1.4
RAID configuration utilities
Depending on the RAID connectors that you use, you can create a RAID set using
the utilities embedded in each RAID controller. For example, use the LSI Logic
Embedded SATA RAID Setup Utility or the Intel® Matrix Storage Manager if you
installed Serial ATA hard disk drives on the Serial ATA connectors supported by the
Intel® 6321ESB Southbridge.
You may use the LSI1068 SAS Configuration Utility if you installed SAS hard
disk drives to the mini-SAS connector(s) supported by the LSI1068 PCI-X SAS
controller.
Refer to the succeeding sections for details on how to use LSI1068 SAS
Configuration Utility.
HPC-2820-ISSE User Manual
6-
6.2
LSI Logic MPT Setup Utility
The LSI Logic MPT Setup Utility is an integrated RAID solution that allows you to
allows you to create the following RAID set(s) from SAS hard disk drives supported
by the LSI1068 PCI-X SAS controller:
•
RAID 1 (Integrated Mirroring)
•
RAID 0 (Integrated Striping)
•
RAID 1E (Integrated Mirroring Enhanced)
6.2.1
Integrated Mirroring
Overview
The Integrated Mirroring (IM) feature supports simultaneous mirrored volumes with
two disks (IM). Integrated Mirroring Enhanced (IME) supports three to eight disks,
or seven mirrored disks plus a hot spare disk.
The IM feature supports hot swap capability, so when a disk in an IM volume
failes, you can easily restore the volume, and the swapped disk is automatically remirrored.
Creating Integrated Mirroring volumes
•
You may use disks of different sized in IM and IME volumes; however, the
size of the smallest disk determines the “logical” size of each member disk.
•
Do not combine Serial ATA and SAS disks in one volume.
•
The RAID BIOS setup screens shown in this section are for reference only
and may not exactly match the items on your screen.
To create an IM volume:
1.
2.
Turn on the system after installing all SAS hard disk drives.
During POST, press <Ctrl+C> to enter the SAS configuration utility.
LSI Logic Corp. MPT SAS BIOS
MPTBIOS-6.08.05.00 (2006.08.02)
Copyright 2000-2006 LSI Logic Corp.
Adapter(s) disabled by user
Press Ctrl-C to start LSI Logic Configuration Utility...
6-
Chapter 6: RAID configuration
3.
The following screen appears. Select a channel and press <Enter> to enter
the setup.
LSI Logic Config Utility
v6.08.05.00 (2006.08.02)
Adapter List Global Properties
Adapter
PCI PCI PCI PCI FW Revision
Status
BUS Dev Fnc Slot
SAS1068
05
03
00
00
1.15.00.00-IR
Disabled
Esc = Exit Menu F1/Shift+1 = Help
Allt+N = Global Properties -/+ = Alter Boot Order
Boot
Order
0
Ins/Del = Alter Boot List
The numbers of the channel depend on the controller.
4.
The Adapter Properties screen appears.
Use the arrow keys to select RAID Properties, then press <Enter>.
LSI Logic Config Utility
v6.08.05.00 (2006.08.02)
Adapter Properties -- SAS1068
Adapter
SAS1068
PCI Slot
00
PCI Address(Bus/Dev/Func)
05.03.00
MPT Firmware Revision
1.15.00.00.IR
SAS Address
500E0180:60831008
NVIDIA Version
25.02
Status
Disabled
Boot Order
0
(Enabled OS only)
Boot Support
RAID Properties
SAS Topology
Advanced Adapter Properties
Esc = Exit Menu
F1/Shift+1 = Help
Enter = Select Item -/+ = Change Item
5.
The Select New Array Type screen apprears.
Use the arrow keys to select Create IM Volume, then press <Enter>.
LSI Logic Config Utility
Select New Array Type -- SAS1068
v6.08.05.00 (2006.08.02)
Create IM Volume
Create Integrated Mirror Array of 2
disks plus an optional hot spare. Data
on the primary disk may be migrated.
Create IME Volume
Create Integrated Mirrored Enhanced
Array of 3 to 8 disks including an
optional hot spare.
ALL DATA on array disks will be DELETED!
Create IS Volume
Create Integrated Striping array of
2 to 8 disks.
ALL DATA on array disks will be DELETED!
Esc = Exit Menu
F1/Shift+1 = Help
Enter = Choose array type to create
HPC-2820-ISSE User Manual
6-
6.
The Create New Array screen shows the disks you can add to make up
the IM volume. Use the arrow key to select a disk, then move the cursor to
the RAID Disk column. To include this disk in the array, press <+>, <->, or
<Space>.
You may also specify the Hot Spare disk here. Select the disk, then move the
cursor to the Hot Spr column, then press <+>, <->, or <Space>.
LSI Logic Config Utility
Create New Array -- SAS1068
Array Type:
Array Size(MB):
Slot
Num
0
1
2
3
v6.08.05.00 (2006.08.02)
IM
------
Device Identifier
SEAGATE
SEAGATE
SEAGATE
SEAGATE
ST373454SS
ST373454SS
ST373454SS
ST373454SS
0003
0003
0003
0003
RAID
Disk
[NO]
[NO]
[NO]
[NO]
Esc = Exit Menu F1/Shift+1 = Help
SPACE/+/- = Select disk for array or hot spare
Hot
Spr
[NO]
[NO]
[NO]
[NO]
Drive
Status
-------------------------
Pred
Fail
-------------
Size
(MB)
70007
70007
35003
35003
C = Create array
By default, the RAID Disk field shows No before array creation. This field is
grayed out under the following conditions:
6-
•
The disk does not meet the minimum requirements for use in a RAID array.
•
The disk is not large enough to mirror existing data on the primary drive.
•
The disk has been selected as the Hot Spare for the RAID array.
•
The disk is already part of another array.
Chapter 6: RAID configuration
7.
A confirmation screen appears.
Press <D> to overwrite any data and create the new IM array.
Press <M> to keep existing data on the first disk. If you choose this option,
data on the first disk will be mirrored on the second disk that you will add to
the volume later. Make sure the data you want to mirror is on the first disk.
LSI Logic Config Utility
Create New Array Type -- SAS1068
v6.08.05.00 (2006.08.02)
M - Keep existing data, migrate to an IM array.
Synchronization of disk will occur.
D - Overwrite existing data, create a new IM array.
ALL DATA on ALL disk in the array will be DELETED!!
No Synchronization performed.
Esc = Exit Menu
F1/Shift+1 = Help
Space/+/- = Select disk for array or hot spare
8.
9.
C = Create array
Repeat steps 5 and 6 to add the second disk to the volume.
When done, press <C> to create the array, then select Save changes then
exit this menu.
Create and save new array?
Cancel Exit
Save changes then exit this menu
Discard changes then exit this menu
Exit the Configuration Utility and Reboot
10. The utility creates the array.
LSI Logic Config Utility
v6.08.05.00 (2006.08.02)
Processing...may take up 1 minute
Creating RAID array
HPC-2820-ISSE User Manual
6-
6.2.2
Integrated Mirroring Enhanced
To create an IME volume:
1.
The Adapter Properties screen appears.
Use the arrow keys to select RAID Properties, then press <Enter>.
LSI Logic Config Utility
Adapter Properties -- SAS1068
Adapter
PCI Slot
PCI Address(Bus/Dev/Func)
MPT Firmware Revision
SAS Address
NVIDIA Version
Status
Boot Order
Boot Support
RAID Properties
SAS Topology
Advanced Adapter Properties
v6.08.05.00 (2006.08.02)
SAS1068
00
05.03.00
1.15.00.00-IR
500E0180:60831008
25.02
Disabled
0
(Enabled OS only)
Esc = Exit Menu
F1/Shift+1 = Help
Enter = Select Item -/+ = Change Item
2.
The Select New Array Type screen apprears.
Use the arrow keys to select Create IME Volume, then press <Enter>.
LSI Logic Config Utility
Select New Array Type -- SAS1068
v6.08.05.00 (2006.08.02)
Create IM Volume
Create Integrated Mirror Array of 2
disks plus an optional hot spare. Data
on the primary disk may be migrated.
Create IME Volume
Create Integrated Mirrored Enhanced
Array of 3 to 8 disks including an
optional hot spare.
ALL Data on array disks will be deleted!
Create IS Volume
Create Integrated Striping array of
2 to 8 disks.
ALL Data on array disks will be deleted!
Esc = Exit Menu
F1/Shift+1 = Help
Enter = Choose array type to create
6-
Chapter 6: RAID configuration
3.
The Create New Array screen shows the disks you can add to make up the
IME volume.
Integrated Mirroring Enhanced (IME) supports three to eight disks, or seven
mirrored disks plus a hot spare disk. Use the arrow key to select a disk, then
move the cursor to the RAID Disk column. To include this disk in the array,
press <+>, <->, or <Space>.
You may also specify the Hot Spare disk here. Select the disk, then move the
cursor to the Hot Spr column, then press <+>, <->, or <Space>.
LSI Logic Config Utility
Create New Array -- SAS1068
Array Type:
Array Size(MB):
Slot
Num
0
1
2
3
v6.08.05.00 (2006.08.02)
IME
51498
Device Identifier
SEAGATE
SEAGATE
SEAGATE
SEAGATE
ST373454SS
ST373454SS
ST373454SS
ST373454SS
0003
0003
0003
0003
RAID
Disk
[Yes]
[NO]
[Yes]
[Yes]
Hot
Spr
[NO]
[NO]
[NO]
[NO]
Esc = Exit Menu F1/Shift+1 = Help
SPACE/+/- = Select disk for array or hot spare
Drive
Status
-------------------------
Pred
Fail
-------------
Size
(MB)
70007
70007
35003
35003
C = Create array
By default, the RAID Disk field shows No before array creation. This field is
grayed out under the following conditions:
4.
5.
•
The disk does not meet the minimum requirements for use in a RAID array.
•
The disk is not large enough to mirror existing data on the primary drive.
•
The disk has been selected as the Hot Spare for the RAID array.
•
The disk is already part of another array.
Repeat step 5 to add the other disks to the volume.
When done, press <C> to create the array, then select Save changes then
exit this menu.
Create and save new array?
Cancel Exit
Save changes then exit this menu
Discard changes then exit this menu
Exit the Configuration Utility and Reboot
6.
The utility creates the array.
LSI Logic Config Utility
v6.08.05.00 (2006.08.02)
Processing...may take up 1 minute
Creating RAID array
HPC-2820-ISSE User Manual
6-
6.2.3
Integrated Striping (IS) volume
Overview
The Integrated Striping (IS) feature provides RAID 0 functionality, supporting
volumes with two to eight disks. You may combine an IS volume with an IM or IME
volume.
Creating Integrated Striping volumes
Do not combine Serial ATA and SAS disks in one volume.
To create an IS volume:
1.
2.
Turn on the system after installing all SAS hard disk drives.
During POST, press <Ctrl+C> to enter the SAS configuration utility.
LSI Logic Corp. MPT SAS BIOS
MPTBIOS-6.08.05.00 (2006.08.02)
Copyright 2000-2006 LSI Logic Corp.
Adapter(s) disabled by user
Press Ctrl-C to start LSI Logic Configuration Utility...
3.
The Adapter Properties screen appears.
Use the arrow keys to select RAID Properties, then press <Enter>.
LSI Logic Config Utility
v6.08.05.00 (2006.08.02)
Adapter Properties -- SAS1068
Adapter
SAS1068
PCI Slot
00
PCI Address(Bus/Dev/Func)
05.03.00
MPT Firmware Revision
1.15.00.00-IR
SAS Address
500E0180:60831008
NVIDIA Version
25.02
Status
Disabled
Boot Order
0
(Enabled OS only)
Boot Support
RAID Properties
SAS Topology
Advanced Adapter Properties
Esc = Exit Menu
F1/Shift+1 = Help
Enter = Select Item -/+ = Change Item
6-10
Chapter 6: RAID configuration
4.
The Select New Array Type screen apprears.
Use the arrow keys to select Create IS Volume, then press <Enter>.
LSI Logic Config Utility
Select New Array Type -- SAS1068
v6.08.05.00 (2006.08.02)
Create IM Volume
Create Integrated Mirror Array of 2
disks plus an optional hot spare. Data
on the primary disk may be migrated.
Create IME Volume
Create Integrated Mirrored Enhanced
Array of 3 to 8 disks including an
optional hot spare.
ALL DATA on array disks will be DELETED!
Create IS Volume
Create Integrated Striping array of
2 to 8 disks.
ALL DATA on array disks will be DELETED!
Esc = Exit Menu
F1/Shift+1 = Help
Enter = Choose array type to create
5.
The Create New Array screen shows the disks you can add to make up
the IS volume. Use the arrow key to select a disk, then move the cursor to
the RAID Disk column. To include this disk in the array, press <+>, <->, or
<Space>.
LSI Logic Config Utility
Create New Array -- SAS1068
Array Type:
Array Size(MB):
Slot
Num
0
1
2
3
v6.08.05.00 (2006.08.02)
IS
102996
Device Identifier
SEAGATE
SEAGATE
SEAGATE
SEAGATE
ST373454SS
ST373454SS
ST373454SS
ST373454SS
0003
0003
0003
0003
RAID
Disk
[Yes]
[NO]
[Yes]
[Yes]
Esc = Exit Menu F1/Shift+1 = Help
SPACE/+/- = Select disk for array or hot spare
HPC-2820-ISSE User Manual
Hot
Spr
[NO]
[NO]
[NO]
[NO]
Drive
Status
-------------------------
Pred
Fail
-------------
Size
(MB)
70007
70007
35003
35003
C = Create array
6-11
By default, the RAID Disk field shows No before array creation. This field is
grayed out under the following conditions:
6.
7.
•
The disk does not meet the minimum requirements for use in a RAID array.
•
The disk is not large enough to mirror existing data on the primary drive.
•
The disk has been selected as the Hot Spare for the RAID array.
•
The disk is already part of another array.
Repeat step 5 to add the other disks to the volume.
When done, press <C> to create the array, then select Save changes then
exit this menu.
Create and save new array?
Cancel Exit
Save changes then exit this menu
Discard changes then exit this menu
Exit the Configuration Utility and Reboot
9.
The utility creates the array.
LSI Logic Config Utility
v6.08.05.00 (2006.08.02)
Processing...may take up 1 minute
Creating RAID array
6-12
Chapter 6: RAID configuration
6.2.4
Managing Arrays
The LSI Logic MPT Setup Utility allows you to perform other tasks related to
configuring and maintaining IM and IME volumes.
Refer to this section to view volume properties, manage the hot spare disk,
synchronize the array, activate the array, and delete the array.
Viewing volume properties
To view volume properties:
1.
On the main menu, select RAID Properties.
LSI Logic Config Utility
Adapter Properties -- SAS1068
Adapter
PCI Slot
PCI Address(Bus/Dev/Func)
MPT Firmware Revision
SAS Address
NVIDIA Version
Status
Boot Order
Boot Support
RAID Properties
SAS Topology
Advanced Adapter Properties
v6.08.05.00 (2006.08.02)
SAS1068
00
05.03.00
1.15.00.00-IR
500E0180:60831008
25.02
Disabled
0
(Enabled OS only)
Esc = Exit Menu
F1/Shift+1 = Help
Enter = Select Item -/+ = Change Item
2.
On the next screen that appears, select View Existing Array.
LSI Logic Config Utility
Select New Array Type -- SAS1068
v6.08.05.00 (2006.08.02)
View Existing Array
View the existing configuration.
Create IM Volume
Create Integrated Mirror Array of 2
disks plus an optional hot spare. Data
on the primary disk may be migrated.
Create IME Volume
Create Integrated Mirrored Enhanced
Array of 3 to 8 disks including an
optional hot spare.
ALL DATA on array disks will be DELETED!
Create IS Volume
Create Integrated Striping array of
2 to 8 disks.
ALL DATA on array disks will be DELETED!
Esc = Exit Menu
F1/Shift+1 = Help
Enter = Choose array type to create
HPC-2820-ISSE User Manual
6-13
3.
The View Existing Array screen appears. Here you can view properties of
the RAID array(s) created. If you have configured a hot spare, it will also be
listed. if you created more than one array, you may view the next array by
pressing <Alt+N>.
LSI Logic Config Utility
View Array -- SAS1068
Array
Identifier
Type
Scan Order
Size(MB)
Status
v6.08.05.00 (2006.08.02)
1 of 1
LSILOGICLogical Volume 3000
IME
0
51498
Optimal
Manage Array
Slot
Num
0
2
3
Device Identifier
SEAGATE ST373454SS
SEAGATE ST373454SS
SEAGATE ST373454SS
Esc = Exit Menu
Enter=Select Item
6-14
0003
0003
0003
RAID
Disk
Yes
Yes
Yes
Hot
Spr
NO
NO
NO
Drive
Status
Ok
Ok
Ok
Pred
Fail
No
No
No
Size
(MB)
34331
34331
34331
F1/Shift+1 = Help
Alt+N=Next Array C = Create an array
Chapter 6: RAID configuration
Managing hot spares
You may configure one disk as a global hot spare to protect critical data on the IM/
IME volume(s). You may create the hot spare disk at the same time you create the
IM/IME volume. Refer to this section when adding a hot spare disk on an existing
volume.
If a disk on an IM/IME volume fails, the utility automatically rebuilds the failed
disk data on the hot spare. When the failed disk is replaced, the utility assigns
the replacement as the new hot spare.
To create a hot spare:
1.
2.
Follow steps 1 ~ 3 of the section “Viewing volume properties.”
From the View Array screen, select Manage Array, then press <Enter>.
LSI Logic Config Utility
View Array -- SAS1068
Array
Identifier
Type
Scan Order
Size(MB)
Status
v6.08.05.00 (2006.08.02)
1 of 1
LSILOGICLogical Volume 3000
IME
0
51498
Optimal
Manage Array
Slot
Num
0
2
3
Device Identifier
SEAGATE ST373454SS
SEAGATE ST373454SS
SEAGATE ST373454SS
Esc = Exit Menu
Enter=Select Item
3.
0003
0003
0003
RAID
Disk
Yes
Yes
Yes
Hot
Spr
NO
NO
NO
Drive
Status
Ok
Ok
Ok
Pred
Fail
No
No
No
Size
(MB)
34331
34331
34331
F1/Shift+1 = Help
Alt+N=Next Array C = Create an array
From the Manage Array screen select Manage Hot Spare, then press
<Enter>.
LSI Logic Config Utility
Manage Array -- SAS1068
Identifier
Type
Scan Order
Size(MB)
Status
v6.08.05.00 (2006.08.02)
LSILOGICLogical Volume 3000
IME
0
51498
Optimal
Manage Hot Spare
Synnchronize Array
Activate Array
Delete Array
Esc = Exit Menu
Enter = Select Item
HPC-2820-ISSE User Manual
F1/Shift+1 = Help
6-15
4.
Use the arrow key to select the disk you would like to configure as hot spare,
then move the cursor to the Hot Spr column. Press <+>, <->, or <Space>.
The Drive Status column field now shows Hot Spare.
Press <C> to commit the changes.
LSI Logic Config Utility
Manage Hot Spare -- SAS1068
Identifier
Type
Scan Order
Size(MB)
Status
Slot
Num
0
1
2
3
v6.08.05.00 (2006.08.02)
LSILOGICLogical Volume 3000
IME
0
51498
Optimal
Device Identifier
SEAGATE
SEAGATE
SEAGATE
SEAGATE
ST373454SS
ST373454SS
ST373454SS
ST373454SS
0003
0003
0003
0003
Hot
Spr
[NO]
[NO]
[NO]
[Yes]
[----]
Drive
Status
Ok
Ok
Ok
Hot Spare
---------
Pred
Fail
No
No
No
No
--
Size
(MB)
34331
34331
34331
35003
-----
Esc = Exit Menu F1/Shift+1 = Help
SPACE/+/- = Change Item
C = Commit Changes
Synchronizing the array
Synchronizing the array allows the utility to resynchronize data on the mirrored disk
in the array. This procedure is seldom required because data synchronization is
automatically done during normal operation.
To synchronize the array:
1. Follow steps 1 ~ 3 of the section “Viewing volume properties” and step 2 of
the section “Managing hot spares.”
2.
From the Manage Array screen select Synchronize Array, then press
<Enter>.
LSI Logic Config Utility
Manage Array -- SAS1068
Identifier
Type
Scan Order
Size(MB)
Status
v6.08.05.00 (2006.08.02)
LSILOGICLogical Volume 3000
IME
0
51498
Optimal
Manage Hot Spare
Synnchronize Array
Activate Array
Delete Array
Esc = Exit Menu
Enter = Select Item
3.
6-16
F1/Shift+1 = Help
Press <Y> to begin the synchronization, or <N> to cancel.
Chapter 6: RAID configuration
Activating an array
If an array is removed from one controller/computer or moved to another, the
array is considered inactive. When you add the array back to the system, you may
reactivate the array.
To activate the array:
1.
From the Manage Array screen, select Activate Array, then press <Enter>.
LSI Logic Config Utility
Manage Array -- SAS1068
Identifier
Type
Scan Order
Size(MB)
Status
v6.08.05.00 (2006.08.02)
LSILOGICLogical Volume 3000
IME
0
51498
Optimal
Manage Hot Spare
Synnchronize Array
Activate Array
Delete Array
Esc = Exit Menu
Enter = Select Item
2.
F1/Shift+1 = Help
Press <Y> to activate, or <N> to cancel.
Deleting an array
•
You cannot recover lost data if you delete an array. Make sure you back up
important data before deleting an array.
•
If you delete an IM (RAID 1) volume, the data is preserved on the primary
disk.
To delete an array:
1.
From the Manage Array screen, select Delete Array, then press <Enter>.
LSI Logic Config Utility
Manage Array -- SAS1068
Identifier
Type
Scan Order
Size(MB)
Status
v6.08.05.00 (2006.08.02)
LSILOGICLogical Volume 3000
IM
0
34332
Optimal
Manage Hot Spare
Synnchronize Array
Activate Array
Delete Array
Esc = Exit Menu
Enter = Select Item
2.
F1/Shift+1 = Help
Press <Y> to delete, or <N> to cancel.
HPC-2820-ISSE User Manual
6-17
6.2.5
1.
Viewing SAS topology
From the Adapter Properties screen, select SAS Topology.
LSI Logic Config Utility
Adapter Properties -- SAS1068
Adapter
PCI Slot
PCI Address(Bus/Dev/Func)
MPT Firmware Revision
SAS Address
NVIDIA Version
Status
Boot Order
Boot Support
RAID Properties
SAS Topology
Advanced Adapter Properties
v6.08.05.00 (2006.08.02)
SAS1068
00
05.03.00
1.15.00.00-IR
500E0180:60831008
25.02
Disabled
0
(Enabled OS only)
Esc = Exit Menu
F1/Shift+1 = Help
Enter = Select Item -/+ = Change Item
Press <Alt+D> to display device properties, or <Alt+M> to display more keys.
More keys for the SAS Topology display:
C = Clear Device Mappings for Non-Present Devices
R = Refresh SAS Topology
Enter = On a SAS Enclosure or Expander - Expand or Collapse Item
Enter = On a Disk Drive - Turn on the Locate LED (next key press turns off)
2.
Information about the volume and its member-disks are then displayed.
LSI Logic Config Utility
v6.08.05.00 (2006.08.02)
SAS Topology -- SAS1068
Device Identifier
Device
SAS1068105:03:001
Info
Direct Attach Devices
Controller
﹂ Enclosure
RAID Physical Disk
SAS
﹂ Bay 0
Bay 1
SEAGATE ST373454SS
0003
SAS
Bay 2
RAID Physical Disk
SAS
Bay 3
RAID Physical Disk
SAS
LSILOGICLogical Volume 3000
﹂ IS VOL
Esc=Exit F1=Help
Alt+D=Device Properties
6-18
Alt+N=More Keys
Chapter 6: RAID configuration
Selecting a boot disk
You can select a boot disk in the SAS Topology screen. This disk is then moved
to scan ID 0 on the next boot, and remains at this position. This makes it easier to
set BIOS boot device options and to keep the boot device constant during device
additions and removals. There can be only one boot disk.
Follow these steps to select a boot disk:
1.
In the SAS BIOS CU, select an adapter from the Adapter List.
The current topology is displayed. If the selection of a boot device is
supported, the bottom of the screen lists the Alt+B option. This is the key
for toggling the boot device. If a device is currently configured as the boot
device, the Device Info column on the SAS Topology screen will show the
word “Boot.”
2.
3.
4.
5.
Select the SAS Topology option.
To select a boot disk, move the cursor to the disk and press Alt+B.
To remove the boot designator, move the cursor to the disk and press Alt+B.
This controller will no longer have a disk designated as boot.
To change the boot disk, move the cursor to the new boot disk and press
Alt+B. The boot designator will move to this disk.
The firmware must be configured correctly in order for the Alt+B feature to work.
LSI Logic Config Utility
v6.08.05.00 (2006.08.02)
Adapter List Global Properties
Adapter
PCI PCI PCI PCI FW Revision
Status
BUS Dev Fnc Slot
SAS1068
05
03
00
00
1.15.00.00-IR
Disabled
Esc = Exit Menu F1/Shift+1 = Help
Allt+N = Global Properties -/+ = Alter Boot Order
HPC-2820-ISSE User Manual
Boot
Order
0
Ins/Del = Alter Boot List
6-19
6.2.6
Global Properties
From the Setup Utility screen, press <Ctrl+C> to enter LSI Logic Configuration,
then select Global Properties. The Global Properties menu allows you to change
related settings.
LSI Logic Config Utility
v6.08.05.00 (2006.08.02)
Adapter List Global Properties
Adapter
PCI PCI PCI PCI FW Revision
Status
BUS Dev Fnc Slot
SAS1068
05
03
00
00
1.15.00.00-IR
Disabled
Esc = Exit Menu F1/Shift+1 = Help
Allt+N = Global Properties -/+ = Alter Boot Order
Boot
Order
0
Ins/Del = Alter Boot List
Pause When Boot Alert Displayed
Sets whether to pause or not when the boot alert displays.
Configuration options: [Yes] [No]
LSI Logic Config Utility
Adapter List Global Properties
Pause When Boot Alert Displayed
Boot Information Display Mode
Support Interrupt
v6.08.05.00 (2006.08.02)
[No]
[Display adapters & installed devices]
[Hook interrupt, the Default]
Restore Defaults
Esc = Exit Menu
F1/Shift+1 = Help
Allt+N = Adapter List -/+ = Change Item
6-20
Chapter 6: RAID configuration
Boot Information Display Mode
Sets the disk information display mode.
Configuration options: [Display adapters & installed devices]
[Display minimal information] [Display adapters and all devices]
[Display adapters only]
LSI Logic Config Utility
Adapter List Global Properties
v6.08.05.00 (2006.08.02)
Pause When Boot Alert Displayed
Boot Information Display Mode
Support Interrupt
[No]
[Display adapters & installed devices]
[Hook interrupt, the Default]
Restore Defaults
Esc = Exit Menu
F1/Shift+1 = Help
Allt+N = Adapter List -/+ = Change Item
Support Interrupt
Configuration options: [Hook interrupt, the Default] [Bypass interrupt hook]
LSI Logic Config Utility
Adapter List Global Properties
Pause When Boot Alert Displayed
Boot Information Display Mode
Support Interrupt
v6.08.05.00 (2006.08.02)
[No]
[Display adapters & installed devices]
[Hook interrupt, the Default]
Restore Defaults
Esc = Exit Menu
F1/Shift+1 = Help
Allt+N = Adapter List -/+ = Change Item
HPC-2820-ISSE User Manual
6-21
Restore Defaults
This option allows you to discard the selections you made and restore the system
defaults.
LSI Logic Config Utility
Adapter List Global Properties
Pause When Boot Alert Displayed
Boot Information Display Mode
Support Interrupt
v6.08.05.00 (2006.08.02)
[No]
[Display adapters & installed devices]
[Hook interrupt, the Default]
Restore Defaults
Esc = Exit Menu
F1/Shift+1 = Help
Allt+N = Adapter List -/+ = Change Item
6-22
Chapter 6: RAID configuration
CHAPTER
Driver Installation
7
7.1
RAID driver installation
After creating the RAID sets for your server system, you are now ready to install
an operating system to the independent hard disk drive or bootable array. This
part provides instructions on how to install the RAID controller drivers during OS
installation.
7.1.1
Creating a RAID driver disk
You may have to use another system to create the RAID driver disk from the
system/motherboard support CD or from the Internet.
A floppy disk with the RAID driver is required when installing Windows®
2000/2003 or Red Hat® Enterprise /SuSE operating system on a hard disk drive
that is included in a RAID set. You can create a RAID driver disk in DOS (using
the Makedisk application in the support CD).
To create a RAID driver disk in DOS environment:
1.
Place the motherboard support CD in the optical drive.
3.
Select the optical drive as the first boot priority to boot from the support
CD. Save your changes, then exit the BIOS Setup.
2.
4.
5.
Restart the computer, then enter the BIOS Setup.
Restart the computer.
Press any key when prompted to boot from CD.
Loading FreeDOS FAT KERNEL GO!
Press any key to boot from CDROM...
The Makedisk menu appears.
A) FreeDOS command prompt
B) Create LSI 1068 SAS for Win2k/Win2k3 32 bit Driver Disk
C) Create LSI 1068 SAS for RHEL3 UP6 32 bit Driver Disk
D) Create LSI 1068 SAS for RHEL3 UP6 64 bit Driver Disk
E) Create LSI 1068 SAS for RHEL4 UP2 32 bit Driver Disk
F) Create LSI 1068 SAS for RHEL4 UP2 64 bit Driver Disk
G) Create the HPC-2820-ISSE emergent BIOS Recovery diskette
H) Flash Phoenix BIOS for HPC-2820-ISSE SYSTEM
I) ESB2 ASF Firmware update
J) Write HPC-2820-ISSE FRU
Please choose A TO J:
7-
Chapter 7: Driver installation
6.
7.
8.
Place a blank, high-density floppy disk to the floppy disk drive, then select the
type of RAID driver disk you want to create by typing the number before the
option
Press <Enter>.
Follow screen instructions to create the driver disk.
For systems with Red Hat® Enterprise versions that are not listed in the
Makedisk menu, explore the support CD and copy the RAID driver disk from the
following path:
For Intel® 6321 LSI MegaRAID: \Drivers\6321 LSI MegaRAID\Driver\Linux\
For LSI 1068 SAS: \Drivers\LSI 1068\Driver\Linux\.
The paths above may differ based on variant models.
7.1.2
Installing the RAID controller driver
Windows® 2000/2003 Server OS
When installing the LSI 1068 driver to your OS, make sure the driver you are
installing supports your current installed OS. We STRONGLY RECOMMEND
that you use the LSI 1068 SAS utility bundled in the support CD to create a
driver disk. Refer to page 6-1 for more information.
During Windows® 2000/2003 Server OS installation
To install the RAID controller driver when installing Windows® 2000/2003
Server OS:
1.
Boot the computer using the Windows® 2000/2003 Server installation CD.
The Windows® 2000/2003 Setup starts.
2.
Press <F6> when the message “Press F6 if you need to install a third party
SCSI or RAID driver...” appears at the bottom of the screen.
3.
When prompted, press <S> to specify an additional device.
HPC-2820-ISSE User Manual
7-
4.
Insert the RAID driver disk you created earlier to the floppy disk drive, then
press <Enter>.
5.
Select the RAID controller driver from the list, then press <Enter>.
LSI
LSI
LSI
LSI
LSI
7-
Logic
Logic
Logic
Logic
Logic
Fusion-MPT
Fusion-MPT
Fusion-MPT
Fusion-MPT
Fusion-MPT
SAS Driver
Driver for
Driver for
Driver for
Driver for
(Server 2003 32-bit)
SAS1064
SAS1068
SAS1064E
SAS1068E
Chapter 7: Driver installation
•
LSI1068 PCI-X SAS controller driver:
- For 32-bit Windows Server 2003, select LSI Logic Fusion-MPT SAS Driver
(Server 2003 32-bit).
6.
7.
- For Windows 2000, select LSI Logic Fusion-MPT Drivers for SAS1068 .
The Windows® 2000/2003 Setup loads the RAID controller drivers from the
RAID driver disk. When prompted, press <Enter> to continue installation.
Setup then proceeds with the OS installation. Follow screen instructions to
continue.
To an existing Windows® 2000/2003 Server OS
To install the RAID controller driver on an existing Windows® 2000/2003 Server OS:
1.
2.
3.
4.
Restart the computer, then log in with Administrator privileges.
Windows® automatically detects the RAID controller and displays a New
Hardware Found window. Click Cancel.
Right-click the My Computer icon on the Windows® desktop , then select
Properties from the menu.
Click the Hardware tab, then click the Device Manager button to display the
list of devices installed in the system.
HPC-2820-ISSE User Manual
7-
5.
Right-click the RAID controller item, then select Properties.
7.
The Upgrade Device Driver Wizard window appears. Click Next.
9.
Select the option Search for a suitable driver for my device
(recommended), then click Next.
6.
8.
Click the Driver tab, then click the Update Driver button.
Insert the RAID driver disk you created earlier to the floppy disk drive.
10. The wizard searches the RAID controller drivers. When found, click Next to
install the drivers.
11. Click Finish after the driver
installation is done.
To verify the RAID controller driver installation:
1.
2.
3.
Right-click the My Computer icon on the Windows® desktop , then select
Properties from the menu.
Click the Hardware tab, then click the Device Manager button.
Click the “+” sign before the item SCSI and RAID controllers, then the LSI
Adapter, SAS 3000 series, 8-port with 1068-StorPort item should appear.
The screen differs based on the controller.
7-
Chapter 7: Driver installation
4.
5.
6.
Right-click the RAID controller driver item, then select Properties from the
menu.
Click the Driver tab, then click the Driver Details button to display the RAID
controller drivers.
Click OK when finished.
Red Hat® Enterprise
To install the Intel® 6321ESB LSI Logic Embedded SATA RAID controller driver
when installing Red Hat® Enterprise OS:
1.
Boot the system from the Red Hat® Installation CD.
2.
At the boot:, type linux dd , then press <Enter>.
When installing a Red Hat 2.4 kernel with a Driver Update Disk (DUD) to a disk
drive attached to a LSI HBA, use the command below at the install prompt:
linux dd updates.
HPC-2820-ISSE User Manual
7-
7-
3.
Select Yes using the <Tab> key when asked if you have the driver disk. Press
<Enter>
4.
Select fd0 using the <Tab> key when asked to select the driver disk source.
Press <Tab> to move the cursor to OK, then press <Enter>.
Chapter 7: Driver installation
5.
When prompted, insert the Red Hat® Enterprise RAID driver disk to the floppy
disk drive, select OK, then press <Enter>.
The drivers for the RAID controller are installed to the system.
6.
Follow screen instructions to continue the OS installation.
HPC-2820-ISSE User Manual
7-
SuSE Linux
To install the RAID controller driver when installing SuSE Linux OS:
1.
Boot the system from the SuSE Installation CD.
3.
A message instructs you to prepare the RAID driver disk. Press <F6>.
2.
7-10
Select Installation from the Boot Options menu, then press <Enter>.
Chapter 7: Driver installation
4.
When prompted, insert the RAID driver disk to the floppy disk drive, then
press <Enter>.
5.
When prompted, select the floppy disk drive (fd0) as the driver update
medium, select OK, then press <Enter>.
The drivers for the RAID controller are installed to the system.
HPC-2820-ISSE User Manual
7-11
7.2
Intel chipset software installation
This section provides instructions on how to install the Plug and Play components
for the Intel® chipset on the system.
You need to manually install the Intel® chipset software on a Windows 2000 /
Server 2003 operating system. To install the Intel® chipset software:
1.
Restart the computer, then log on with Administrator privileges.
3.
Click the item Chipset Drivers from the menu.
2.
7-12
Insert the motherboard/system support CD to the optical drive. The support
CD automatically displays the Drivers menu if Autorun is enabled in your
computer.
Chapter 7: Driver installation
4.
The Intel(R) Chipset Software Installation Utility window appears. Follow
the screen instructions to complete installation.
5.
Select Yes to accept the terms of the License Agreement and continue the
process.
HPC-2820-ISSE User Manual
7-13
7-14
6.
Read the Readme File Information and press Next to activate the
installation.
7.
After completing the installation, click Finish to restart the computer.
Chapter 7: Driver installation
7.3
LAN driver installation
This section provides the instructions on how to install Intel® Gigabit LAN controller
drivers.
7.3.1
Windows 2000/Server 2003
To install the Intel® Gigabit LAN controller driver on a Windows® 2000/ Server 2003
OS:
1.
2.
3.
Restart the computer, and then log on with Administrator privileges.
Insert the motherboard/system support CD to the optical drive. The CD
automatically displays the Drivers menu if Autorun is enabled in your
computer.
•
•
Windows® automatically detects the LAN controllers and displays
window. Click Cancel to close this window.
If Autorun is NOT enabled in your computer, browse the contents of the
support CD to locate the file AUTORUN.EXE from the
\Drivers\Intel 82563EB folder. Double-click the AUTORUN.EXE and
follow step 4 to run the installation.
Click the LAN Drivers option.
HPC-2820-ISSE User Manual
7-15
7-16
4.
Click the Install Drivers option to begin installation.
5.
Click Next button when the Intel® PRO Network Connections –
InstallShield Wizard window appears.
Chapter 7: Driver installation
6.
Select the “I accept the terms in the license agreement” and then click the
Next button.
7.
Press the Complete and click Next button to fully install the driver, Intel®
PROSet for Windows Device Manager and Advanced Networking Services.
HPC-2820-ISSE User Manual
7-17
7-18
8.
Follow the screen instructions to complete installation.
9.
When finished, press Finish to continue.
Chapter 7: Driver installation
To verify the LAN controller driver installation:
1.
2.
3.
Right-click the My Computer icon on the Windows® desktop , then select
Properties from the menu.
Click the Hardware tab, then click the Device Manager button.
Click the “+” sign before the item Network adapters, then Intel(R) PRO/1000
EB Network Connection with I/O Acceleration item should appear.
HPC-2820-ISSE User Manual
7-19
7.3.2
Red Hat/SuSE Linux
Follow these instructions when installing the Intel® LAN controller base driver for
the in Red Hat® and SuSE Linux operating system.
Before installing the LAN driver:
Before installing the LAN driver, you must install the kernel development
application. To install the kernel development:
1.
2.
3.
4.
Insert the Linux OS installation CD Disk 1 to the optical drive.
Double click “Application” > “System setting” > “Add / Remove
application”.
Select “Kernel Development” from the Development Tools.
Follow the later steps and add different CDs according to the instructions
displayed.
Building the driver from the TAR file:
1.
2.
Insert the motherboard/system support CD to the optical drive and mount the
optional drive in the Linux platform.
Copy the base driver tar file from the motherboard/system support CD to the
directory of your local hard disk. The name format of driver file is “e1000<Version>.tar.gz”.
For example: the file name of driver version 7.0.38 is “e1000-7.0.38.tar.gz”.
•
The Intel® LAN driver for Linux OS is located in:
\Drivers\INTEL 82563EB\PRO1000\LINUX
3. Untar or unzip the archive.
tar zxf e1000-x.x.x.tar.gz
4.
Change to the driver src directory.
5.
Use the command “makeinstall” to compile the driver module.
6.
7-20
cd e1000-x.x.x/src/
makeinstall After reboot the system, please refer to Linux distribution documentation to
configure the network protocol and IP address.
Chapter 7: Driver installation
7.4
VGA driver installation
This section provides instructions on how to install the ATI® ES1000 Video
Graphics Adapter (VGA) driver.
7.4.1
Windows® 2000/Server 2003
You need to manually install the ATI® ES1000 VGA driver on a Windows® 2000 /
Server 2003 operating system. To install the ATI® ES1000 VGA driver:
1.
2.
Restart the computer, then log on with Administrator privileges.
Insert the motherboard/system support CD to the optical drive. The support
CD automatically displays the Drivers menu if Autorun is enabled in your
computer.
The VGA Drivers menu if Autorun is enabled in your computer.
3.
Click the item ATI ES1000 from the menu.
HPC-2820-ISSE User Manual
7-21
7-22
4.
The ATI Software window appears. Follow the screen instructions to
complete installation.
5.
Select Yes to accept the terms of the License Agreement and continue the
process.
Chapter 7: Driver installation
button to select Express installation to activate quick
6.
Press the
installation.
7.
After completing the installation, restart the computer.
HPC-2820-ISSE User Manual
7-23
7-24
Chapter 7: Driver installation
APPENDIX
A
Reference Information
A.1
Power supply
A.1.1
General description
The barebone server comes with one SSI-type 750W redundant power supply with
115V/230V AC voltage, 50Hz/60Hz frequency.
•
You may purchase and install a second power supply with the same
specifications.
•
When you installed two power supply modules, make sure to plug both
modules to a power outlet to achieve redundancy.
There are nine (9) power plugs from the power supply unit. Take note of the
devices to which you should connect the plugs.
P1
P6
P3
P1 Motherboard 24-pin ATX power connector P2 P4 P5 P7
P9
P8
P2 Motherboard 8-pin +12V CPU power connector
P3 Motherboard 4-pin power connector
P4 Mid-fan board power connector
P5 SAS HDD backplane board power connector
P6 SMBus connector
P7 SAS HDD backplane board power connector
P8 SAS HDD backplane board power connector
P9 Optical drive/floppy drive power connector
A-
Appendix: References
A.1.2
Specifications
Output voltage regulation
Output Voltage
Min (V)
+3.3V
3.25
+5V
+12V
-12V
+5VSB
4.90
11.40
-11.40
4.85
Nom (V)
3.30
5.00
12.00
Max (V)
Ripple/Noise
3.35
50mVp-p
12.60
120mVp-p
5.20
50mVp-p
5.10
50mVp-p
-12.00
-13.80
Max (A)
Max. Output(W)
5.00
120mVp-p
Output current capacity
Output Voltage
Min (A)
+3.3V
0.5
20.0
0.5
12.5
+5V
0.5
+12V2
0.5
+12V1
+12V3
1.5
+12V4
1.5
-12V
0.0
+5VSB
0.0
66.0
20.0
100.0
12.5
216.0
14.0
14.0
0.5
2.0
216.0
300.0
300.0
6.0
10.0
Over-voltage protection
Voltage
+3.3V
Min (V)
+5V
+12V
3.8
5.7
13.5
Max (V)
4.3
6.5
15.0
Redundant power LED
Refer to section 1.6.4 for details.
HPC-2820-ISSE User Manual
A-
A.2
Troubleshooting
Some problems that you may encounter are not due to defects on the system or
the components. These problems only requires simple troubleshooting actions
that you can perform by yourself.
Problem
Action
The power LED on the server or on 1.
the monitor do not light up
2.
3.
Make sure that the power cables
are connected to a grounded
power outlet.
Press the power button to make
sure that the system is turned
on.
The keyboard does not work
Check if the keyboard cable is properly
connected to the PS/2 keyboard port.
The mouse does not work
Check if the mouse cable is properly
connected to the mouse port.
The system does not perform
power-on self tests (POST) after it
was turned on
1.
The system continuously beeps
after it was turned on
2.
1.
2.
A-
Check if the power cable is
properly connected to the power
connector in the system rear
panel.
Check the memory modules
and make sure you installed the
DIMMs the system supports.
Make sure that the DIMMs are
properly installed on the sockets.
Check the memory modules
and make sure you installed
supported DIMMs.
Make sure that the DIMMs are
properly installed on the sockets.
Appendix: References
Problem
The message “Non-system disk or
disk error” appears
Network connection not available
Action
1.
2.
1.
2.
Why do the fans run in full speed
after the system is switched on?
(system fan: 5700RPM; rear fan:
11800RPM)
Check if a bootable HDD is
active.
Check if the HDDs are properly
installed.
Make sure that the network
cable is connected to the LAN
port on the rear panel.
Make sure that you have
installed the LAN drivers from
the support CD.
Please go to Hardware Monitor in
BIOS setup and check the CPU
temperature and setting of SmartFan Control. If Smart-Fan is disabled,
please set Smart-FAN control to
“Enabled”. If Smart -Fan is already
enabled, please check the followings:
1. If CPU temperature is over 600C in
BIOS setup, please shut down and reinstall CPU’s heatsink to make sure
that CPU’s heatsink is tightly secured
to the CPU.
2. If CPU temperature is over 60 0C
in BIOS setup, please check whether
the arrow on the system fans points
to the direction on the rear panel. Reinstall the fan in case it causes CPU
to overheat.
3. If CPU temperature is under 60
0
C in BIOS setup, please check the
CPU_FAN1 connector on the MB
connected with 3-pin connectors on
the mid-fan board (FANBPC-AR21).
HPC-2820-ISSE User Manual
A-
A-
Appendix: References