6
© Siemens AG 2011
SITOP 1-phase and 2-phase
24 V DC, 6 A
6/2
6/2
6/4
SITOP PSA100E 6 A
PSU100D 6.2 A
Ordering data and additional information
Export regulations AL and ECCN
see page 17/9
Siemens KT 10.1 · 2012
© Siemens AG 2011
SITOP 1-phase and 2-phase
24 V DC
Output current 6 A
■ Overview
NEW
Product
Special design
PSA100E
Special design
PSU100D
Power supply, type
6A
6.2 A
Order No.
6EP1 233-1AA00
6EP1 333-1LD00
The power supply is optimally designed for standard
requirements in the industrial environment; rugged metal
enclosure; flexible mounting either on standard rails or
directly on a wall; removable terminals.
The low-cost power supply in flat aluminum housing
can be screwed directly on a wall in various mounting
positions; with wide-range input for global use.
Special design
PSA100E
Special design
PSU100D
Rated voltage value Vin rated
1-phase AC
230 V AC
Voltage range
187 ... 264 V
1-phase AC
100-240 V AC
Wide-range input
85 ... 264 V
Overvoltage resistance
Mains buffering at Iout rated
Rated line frequency value; range
–
> 10 ms
50/60 Hz; 47 ... 63 Hz
> 15 ms at Vin = 115/230 V
50/60 Hz; 47 ... 63 Hz
Rated current Iin rated
Switch-on current limit (+25 °C)
I2t
1.4 A
< 35 A
< 1.2 A2s
3.1-2.0 A
< 75 A
< 6.5 A2s
Built-in incoming fuse
Recommended miniature circuit
breaker (IEC 898) in the mains
power input
Internal
10 A or higher, characteristic C
Internal
10 A or higher, characteristic C or 16 A, characteristic
B
Rated voltage Vout rated
Controlled, isolated DC voltage
24 V DC
Controlled, isolated DC voltage
24 V DC
Total tolerance
• Static line compensation
• Static load compensation
±3 %
Approx. 0.1 %
Approx. 0.5 %
±2 %
Approx. 0.5 %
Approx. 1 %
Residual ripple
Spikes (bandwidth: 20 MHz)
< 150 mVpp
< 250 mVpp
< 100 mVpp
< 100 mVpp
Adjustment range
Status display
On/off behavior
23 ... 26 V
Green LED for 24 V OK
Overshoot of Vout < 5 %
22.0 ... 28.0 V
Green LED for 24 V OK
Overshoot of Vout < 2 %
Startup delay /
voltage rise
Rated current value Iout rated
< 0.3 s/< 500 ms
< 1 s/< 30 ms
6A
6.2 A
Current range
• Up to + 60 °C
• Derating
0 ... 6 A (up to +45 °C)
0 ... 3 A (up to +70 °C)
0 ... 6.2 A (up to +50 °C)
0 ... 3.1 A (up to +70 °C)
Yes, 2 units
Yes, 2 units
The product families are
highlighted in the same color.
For an explanation of the product
families, see chapter 1, pages 1/8
through 1/12.
6
■ Technical specifications
Product
Input
Output
Dynamic overcurrent on
• Power-up on short circuit
• Short circuit during operation
Parallel switching for
enhanced performance
6/2
Siemens KT 10.1 · 2012
© Siemens AG 2011
SITOP 1-phase and 2-phase
24 V DC
Output current 6 A
■ Technical specifications (continued)
Product
Power supply, type
Order No.
Efficiency
Efficiency at Vout rated, Iout rated
Power loss at Vout rated, Iout rated
Closed-loop control
Dyn. mains compensation
(Vin rated ± 15 %)
Dynamic load smoothing
(Iout: 50/100/50 %)
Load step settling time
• 50 at 100 %
• 100 at 50 %
Protection and monitoring
Output overvoltage protection
Current limitation
Special design
PSA100E
6A
6EP1 233-1AA00
Special design
PSU100D
6.2 A
6EP1 333-1LD00
Approx. 87 %
Approx. 22 W
Approx. 86 %
Approx. 24 W
<0.3 % Vout
Typ. ± 0.5 % Vout
Typ. ± 2.0 % Vout
Typ. ± 5.0 % Vout (0 to 100 %)
Typ. 0.1 ms
Typ. 0.1 ms
< 35 V
Typ. 6.6 A
Short-circuit protection
Electronic shutdown,
automatic restart
Sustained short-circuit current rms < 3.6 A
value
Overload/short-circuit indicator
–
Safety
Primary/secondary isolation
Yes, SELV output voltage Vout according to
EN 60950-1 and EN 50178
Protection class
Class I
Leakage current
< 3.5 mA (typ. 0.8 mA)
Safety test
Yes; CB Scheme
CE mark
Yes
UL/cUL (CSA) approval
cULus-Listed (UL 508, CSA C22.2 No.107.1), File
E197259
Explosion protection
FM approval
Marine approval
Degree of protection (EN 60529)
EMC
Emitted interference
Supply harmonics limitation
Noise immunity
Operating data
Ambient temperature range
Transport/storage temperature
range
Humidity class
Mechanics
Connections
• Supply input L, N, PE
• Output +
• Output –
Dimensions (W x H x D) in mm
Weight, approx.
Installation
6
< 35 V
7.4 A
Electronic shutdown,
automatic restart
16 A
–
–
–
–
IP20
Yes, safety extra low output voltage Vout according to
EN 60950-1
Class I
< 3.5 mA (typ. 1 mA)
Yes; CB Scheme in preparation
Yes
cULus-Listed (UL 508, CSA C22.2 No.107.1) in
preparation; cURus (UL 60950-1, CSA C22.2
No. 60950-1) in preparation
–
–
–
IP20
EN 55022 Class B
–
EN 61000-6-2
EN 55022 Class B
–
EN 61000-6-2
-10 ... +70 °C with natural convection
-10 ... +70 °C with natural convection
-40 ... +85 °C
-25 ... +85 °C
Climate class 3K3 according to
EN 60721, no condensation
Removable screw terminal for
1 × 0.5 ... 2.5 mm2 each
Removable screw terminal for 1 × 0.5 ... 2.5 mm2
Removable screw terminal for 1 × 0.5 ... 2.5 mm2
52 × 170 × 110
0.9 kg
Snaps onto DIN rail EN 60715 35x7.5/15.
Wall mounting
One screw-type terminal each for 0.3 ... 1.3 mm2
solid/finely stranded
2 screw terminals for 0.3 ... 1.3 mm2
2 screw terminals for 0.3 ... 1.3 mm2
97 x 178 x 38
0.55 kg
Wall mounting
–
–
Accessories
Siemens KT 10.1 · 2012
6/3
© Siemens AG 2011
SITOP 1-phase and 2-phase
24 V DC
Output current 6 A
■ Selection and ordering data
Product
Input
Output
Voltage Vin rated
Voltage Vout rated
Current
Iout rated
Order No.
230 V AC
24 V DC
6A
6EP1 233-1AA00
100-240 V AC
24 V DC
6.2 A
6EP1 333-1LD00
Special design, PSA100E
Special design, PSU100D
(Planned delivery date:
December 2011)
NEW
6
■ Further information
Additional information is available in the Internet under:
• 2D dimensional drawings, 3D CAD data, circuit diagram
macros:
www.siemens.com/sitop-cax
• Operating instructions:
www.siemens.de/sitop-manuals
• Find the right product with the SITOP Selection Tool:
www.siemens.com/sitop-selection-tool
6/4
Siemens KT 10.1 · 2012
Price