General Installation Instructions
LED
• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions and other hazards,
please read all warnings and instructions included with and on the luminaire box and all luminaire labels.
• Before installing, servicing or performing routine maintenance upon this equipment, follow these general precautions.
• Installation and service of luminaires should be performed by a qualified licensed electrician.
• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation and any hazards
involved. Regular luminaire maintenance programs are recommended.
• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient dirt level and
minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm water and any mild, nonabrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly become dirty on the inside, wipe refractor/
lens and clean in above manner, replacing damaged gaskets as necessary.
• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been damaged during
transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.
• Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.
• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency to meet in
connection with installation, operation or maintenance. Should further information be desired or should particular problems arise which
are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be referred to Acuity Brands Lighting, Inc., a parent
company of Peerless Lighting.
WARNING
RISK OF ELECTRIC SHOCK
4Disconnect or turn off power before installation or
servicing.
4Verify that supply voltage is correct by comparing it with
the luminaire label information.
4Make all electrical and grounded connections in
accordance with the National Electrical Code (NEC) and
any applicable local code requirements.
4All wiring connections should be capped with UL approved
recognized wire connectors.
4To prevent luminaire row from over-­current: By adding
the input current of each luminaire section marked on
the luminaire, the total current per power feed must not
exceed the maximum line wire amperage marked on the
luminaire and the power feed cord/wire amperage rating
whichever the least.
WARNING
RISK OF BURN
4Allow lamp/luminaire to cool before handling. Do not
touch enclosure or light source.
4Do not exceed maximum wattage marked on luminaire
label.
4Follow all manufacturer’s warnings, recommendations and
restrictions for: driver type, burning position, mounting
locations/methods, replacement and recycling.
Part Number: PIN004102 Description: “INSTR, IMPORTANT SAFETY LED” Revision: C Effective Date: 07/2012 ECO3665 page 1 of 2
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2014 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
Limited warranty applies. Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
General Installation Instructions LED A
General Installation Instructions
LED
CAUTION
RISK OF INJURY
CAUTION
RISK OF FIRE
4Wear gloves and safety glasses at all times when removing
luminaire from carton, installing, servicing or performing
maintenance.
4Avoid direct eye exposure to the light source while it is on.
4Keep combustible and other materials that can burn away
from lamp/lens.
4Do not operate in close proximity to persons, combustible
materials or substances affected by heat or drying.
CAUTION
RISK OF PRODUCT DAMAGE
4Never connect components under load.
4Do not mount or support these luminaires in a manner that can cut the outer jacket or damage wire insulation.
4Unless individual product specifications deem otherwise: Never connect an LED product directly to a dimmer packs, occupancy
sensors, timing devices, or other related control devices. LED luminaires must be powered directly off a switched circuit.
4Unless individual product specifications deem otherwise: Do not restrict luminaire ventilation. Allow for some volume of airspace
around luminaire. Avoid covering LED luminaires with insulation, foam or other material that will prevent convection or conduction
cooling.
4Unless individual product specifications deem otherwise: Do not exceed luminaire’s maximum ambient temperature.
4Only use luminaire in its intended location.
4LED products are polarity sensitive. Ensure proper polarity before installation.
4Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be worn during all installation or
servicing of the unit.
4Do not touch individual electrical components as this can cause ESD, shorten lamp life or alter performance.
4Some components inside the luminaire may not be serviceable. In the unlikely event your unit may require service, stop using the
unit immediately and contact a Peerless Lighting representative for assistance.
4Always read the fixtures complete installation instructions prior to installation for any additional luminaire specific warnings.
SAVE THESE INSTALLATION INSTRUCTIONS
Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory statements.
Failure to follow any of these instructions could void product warranties.
For a complete listing of product Terms and Conditions, please visit PeerlessLighting.com.
Peerless Lighting, an Acuity Brands Company, assumes no responsibility for claims arising out of improper or careless installation or handling of its products.
Part Number: PIN004102 Description: “INSTR, IMPORTANT SAFETY LED” Revision: C Effective Date: 07/2012 ECO3665 page 2 of 2
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2014 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
Limited warranty applies. Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
General Installation Instructions LED
B
General Installation Instructions WARNING
To reduce the risk of death, injury or property damage from fire, electric shock, cuts, abrasions, falling parts and other
hazards:
• Service of the equipment must be performed by qualified service personnel.
• Installation and maintenance must be performed by a person familiar with the construction and operation of this product
and any hazards involved. All applicable codes and ordinances must be followed.
• Read this document before installing, servicing or maintaining this equipment or installing a lamp. These instructions do
not cover all installation, service and maintenance situations. If your situation is not covered, or, if you do not
understand these instructions or additional information is required, contact Peerless Lighting or your local Peerless
Lighting distributor.
• Read and follow all warnings and instructions provided by the lamp manufacturer.
WARNING
Before installing, servicing or maintaining this equipment, follow these general precautions. To reduce the risk of
electrocution:
• Make sure the equipment is properly grounded.
• Always de-energize the circuit and/or equipment before connecting to, disconnecting from or servicing the equipment.
To prevent luminaire row from over-current:
• By adding the input current of each luminaire section marked on the luminaire, the total current per power feed must not
exceed the maximum line wire amperage marked on the luminaire and the power feed cord/wire amperage rating
whichever is the least.
To reduce the risk of fire:
• Keep material away that can burn from hot lamp.
• Make sure lamps are correctly installed.
• Use supply conductors with a minimum installation temperature rating as specified on equipment.
To reduce the risk of personal injury from cuts, abrasions or falling parts:
• Wear gloves to prevent cuts or abrasions from sharp edges when removing from carton, handling and maintaining this
equipment.
• Do not use abrasive materials, glass cleaners or other solvents on reflector or lens. These substances may damage
equipment and cause parts to eventually break and fall.
• Do not install a damaged fixture.
CAUTION
Observe lamp manufacturer’s recommendations and restrictions on lamp operation including but not limited to ballast
type, burning position, replacement and cycling. Use only lamps that comply with applicable ANSI standards.
NOTICE: If lamp is marked
it contains mercury. Follow disposal laws. See www.lamprecycle.org
Peerless Lighting, a division of Acuity Brands Lighting, Inc., assumes no responsibility for
claims arising out of improper or careless installation or handling of this product.
SAVE THESE INSTALLATION INSTRUCTIONS
Part Number: PIN004100 Revision: E Effective Date: 07/2012 ECO3665
Staple Wall — LED and Fluorescent
INSTALLATION INSTRUCTIONS
PIN005901 REV. C 03/14 ECO3722
SPW9L/SPW9/SPW4
These installation instructions are used for installing the following luminaires and kits:
Luminaires
Support Location
Mounting Kit
SPW9L
Normal Power Feed
SPWFK
SPW9
Non-Power Feed
SPWSK
SPW4
Luminaire
End Cap Kit
Dust Cover
SPW9L
SPW9EP or SPW9FEP
SPW9LDU
SPW9
SPW9EP or SPW9FEP
SPW9DU
SPW4
SPW4EP or SPW4FEP
SPW4DU
WARNING: Please read the “important safety instructions” prior to installation of this product. The mounting instructions can be found inside the mounting
kits or downloaded from PeerlessLighting.com.
A) Identification of SPW9L, SPW9 and SPW4 Luminaires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 1
B) WALL-Mounted Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2-3
C) OPTIONAL Dust Cover (DU) Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3
A) Identification of SPW9L, SPW9 and SPW4 Luminaires
SPW9L & SPW9
SPW4
Rounded (EP)
ROUND End CapEND C AP
WIRE WAY & MOUNTING CHANNEL POWER “PIGTAIL” WIRE CONNECTORS Squared (FEP)
End Cap
DIMENSIONS OF STANDARD SECTION
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2014 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
Llimited warranty applies. Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
Staple Wall — LED and Fluorescent installation instructions
1
Staple Wall – LED and Fluorescent
PIN005901 REV. C 03/14 ECO3722
SPW9L/SPW9/SPW4
B) Wall-Mounted Installation
1
Using a laser or snap line, mark wall for
center line. Using support spacing diagram
determine locations of power feed and
supports. Cut wall material and install 2”x4”
J-box (by others) at feed location. Pull
building wires as shown.
4
For individual luminaire (IND option). Raise
the luminaire into position. Connect to
building power using appropriate wire nuts
(by others). Level and secure the luminaire
to wall mounting brackets. Install wireway
covers to complete the installation. Note: For
modular luminaires, skip to Steps 5-10.
7
To join luminaires together, raise the
connecting luminaire into position. Plug in
the wire connectors.
2
Sandwich J-box cover plate between J-box
and bracket as shown. Install mounting
bracket to wall using (2) 1/4-20 bolts (by
others).
5
Connect power feed wire harness as shown.
Insert connection back into luminaire. Fold
or break the aligner tab at joiner, install and
secure end-cap. Raise the luminaire into
position. Connect to building power using
appropriate wire nuts (by others). Secure the
luminaire to wall mounting brackets.
8
Connect the luminaire at the joiner location
and secure to wall. Repeat Steps 6-8 until
last section is hung. For modular fluorescent
luminaires (left). Bolt luminaires together
with (2) ¼-20 screws using a Philips
screwdriver. For modular LED luminaires
(right). Bolt luminaires together with (2)
¼-20 socket head screws using a 3/16
socket allen wrench.
3
Install non-power feed wall brackets to wall
along laser/snap line using (2) 1/4-20 bolts
per bracket. Use (2) wall brackets for 4’ and
8’ luminaire sections, (3) wall brackets for 12’
luminaire sections.
6
At non-power feed location for next
luminaire in run, gently pull female wire
harness from cavity (or cap-off) as shown.
Disconnect and discard power feed (pigtail).
9
For the last luminaire, fold or break the
aligner tab at joiner, install and secure endcap. Raise the luminaire into position. Plug in
the wire connectors. Connect the luminaire
at the joiner location and secure to wall as in
Steps 7 and 8.
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2014 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
Limited warranty applies. Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
Staple Wall – LED and Fluorescent
2
Staple Suspended – LED and Fluorescent
PIN005900 REV. D 03/14 ECO3722
SPM9L/SPM9/SPM4
10
Level the whole row at each hanger location
as necessary. Tighten screws on all hangers.
Install wireway covers on both ends to
complete the installation.
C) OPTIONAL Dust Cover (DU) Installation
1
For SPW9L (LED), simply remove the dust
cover for cleaning during maintenance and
then restore the part by overlaying it atop
the luminaire as shown.
2
For SPW9 AND SPW4 (Fluorescent), simply
remove the dust cover to re-lamp during
maintenance and then replace the dust cover
centering it over the lamp(s) as shown.
2246 5th Street, Berkeley, CA 94710 • Tel: 510.845.2760 • Fax: 510.845.2776 • Email: techsupport@peerlesslighting.com • PeerlessLighting.com
© 2014 Acuity Brands Lighting, Inc. All Rights Reserved. “Peerless” is a registered trademark of Acuity Brands Lighting.
Products in this document may be covered by one or more U.S. Patents and Patents Pending. Specifications subject to change without notice.
Limited warranty applies. Complete warranty terms located at www.AcuityBrands.com/CustomerResources/Terms_and_Conditions.aspx
Staple Suspended – LED and Fluorescent
2