Color Page
Components:
LIN Mounted Light Kit Installation
(Elevance Chairs Only) [002-1688-00]
Warning
Always disconnect power before removing covers.
Failure to do so may result in personal injury.
LIN Conn. Harness.. 1
Strain Relief............. 1
Wall Cover............... 1
Special Tools:
none
Attention!
Electrical installations must be completed
by a Licensed Electrician.
Language of origin: English
Step 1: Access Power Supply.
A) Disconnect power.
B) Remove cover(s) as needed.
Cabinet Mounted Light
Track Light / Monitor
LED Lights (only)
LED / Halogen Lights
Wall Mounted Light
TP201 Rev. A
Ceiling Mounted Light
Track Light
DA
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-1
i
Style G
003-2614-00 Rev. A (5/30/13)
Color Page
Track Mounted Light Disconnections
Step 3: Remove Power Cord.
Step 2: Disconnect Power Cord.
A) Remove strain relief from ceiling plate.
B) Pull power cord wires thru ceiling plate.
A) Loosen screws on terminal block.
B) Remove power cord wires from terminal block.
Ceiling
Plate
Terminal
Block
Screws
Strain
Relief
Power
Cord
TP201 Rev. A
Power
Cord
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-2
Style G
Color Page
LIN Installation (Track Mounted Lights)
Step 4: Install Strain Relief.
Step 3: LIN connection preparation.
A) If necessary to run wiring use 30 foot cable provided.
B) Cut off quick disconnects.
C) Strip approximately 1/4 inch of insulation off both wires.
LIN
A) Feed LIN connector and power cord thru both
new strain relief (provided) and ceiling plate.
B) Install strain relief into ceiling plate.
Quick
Disconnects
Step 5: Connect Wires.
Strain Relief
(NEW)
Ceiling
Plate
A)
B)
C)
D)
Insert power cord and LIN connector wires
into terminal block as shown.
Tighten terminal block screws.
Route LIN wires to base of chair as required
by facility.
Go to Last Page in this instructions to see LIN
connection to Elevance Chair.
LIN
Terminal
Block
LIN
Power
Cord
Screw
TP201 Rev. A
Power
Cord
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-3
Style G
Color Page
Ceiling Mounted Light Disconnections
Step 2: Disconnect Power Cord.
A) Loosen screws on terminal block.
B) Remove power cord wires from terminal block.
C) Remove cable clamp from ceiling plate.
Step 3: Remove Power Cord.
A) Remove strain relief from ceiling plate.
B) Pull power cord wires thru ceiling plate.
Terminal
Block
Strain
Relief
Ceiling
Plate
DA4005i
TP201 Rev. A
Cable
Clamp
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-4
Style G
Color Page
LIN Installation (Ceiling Mounted Lights)
Step 3: LIN connection preparation.
A) If necessary to run wiring use 30 foot cable provided.
B) Cut off quick disconnects.
C) Strip approximately 1/4 inch of insulation off both wires.
LIN
Quick
Disconnects
Step 5: Connect Wires.
Step 4: Install Strain Relief.
A) Feed LIN connector and power cord thru both
new strain relief (provided) and ceiling plate.
B) Install strain relief into ceiling plate.
A)
B)
C)
D)
E)
Insert power cord and LIN connector wires
into terminal block as shown.
Tighten terminal block screws.
Install cable clamp to ceiling plate.
Route LIN wires to base of chair as
required by facility.
Go to Last Page in this instructions to see
LIN connection to Elevance Chair.
Strain Relief
(NEW)
TP201 Rev. A
Terminal
Block
LIN
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
Power
Cord
English-5
Cable
Clamp
DA4006i
Style G
Color Page
Track Light / Monitor Disconnections
Step 2: Disconnect Power Cord.
A) Loosen screws on terminal block.
B) Remove power cord wires from terminal block.
Step 3: Remove Power Cord.
A) Remove strain relief from mounting plate.
B) Pull power cord wires thru mounting plate.
Strain
Relief
Terminal
Block
DA
Mounting
Plate
TP201 Rev. A
Power
Cord
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-6
Style G
i
Color Page
LIN Installation (Track Light / Monitor)
Step 3: Install Strain Relief.
A)
B)
C)
Feed LIN connector and power cord thru both
new strain relief (provided) and ceiling plate.
Install strain relief into ceiling plate.
Connect LIN wires to quick disconnects.
Step 4: Connect Wires.
A)
B)
C)
D)
Insert power cord wires into terminal block as shown.
Tighten terminal block screws.
Route LIN wires to base of chair as required by facility.
Go to Last Page in this instructions to see LIN
connection to Elevance Chair.
Strain Relief
(NEW)
DA
Terminal
Block
Quick
Disconnects
Power
Cord
TP201 Rev. A
LIN
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-7
Style G
i
Color Page
Wall / Cabinet Light Disconnections
Step 2: Remove Hole Plug.
A) Remove hole plug from bottom cover.
B) It is not necessary to replace bottom cover
if hole plug exists.
Step 3: Replace bottom cover (if necessary).
A) Disconnect transform wires from fuse holders.
B) Disconnect power cord wires.
Note: Refer to LIN Installation steps after removing Hole Plug.
DA
i
Power
Cord
TP201 Rev. A
Transformer
Wire
Bottom
Cover
Transformer
Wire
Hole
Plug
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
Fuse
Holders
English-8
Style G
Color Page
Wall / Cabinet Light Disconnections
Step 5: Assemble NEW Bottom Cover.
A) Remove fuse holders and power cord with strain relief.
B) Assemble fuse holders and power cord with strain relief
into new bottom cover (provided).
Step 4: Remove Bottom Cover.
A) Remove two screws and washers (save)
from bottom cover.
Power
Cord
Bottom
Cover
Strain
Relief
Fuse
Holders
DA
Bottom Cover
(NEW)
Bottom
Cover
Power
Cord
TP201 Rev. A
Washer
Strain
Relief
Washer
Fuse
Holders
Screws
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-9
Style G
i
Color Page
Wall / Cabinet Light Disconnections
Step 6: Install NEW Bottom Cover.
Step 7: Connect Wiring.
A) Install new bottom cover using two screws
and washers into wall plate.
A) Connect transform wires to fuse holders.
B) Connect power cord wires.
Bottom Cover
(NEW)
DA
i
Washer
Transformer
Wire
Screws
TP201 Rev. A
Power
Cord
Transformer
Wire
Washer
Wall
Plate
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-10
Style G
Color Page
LIN Installation (Wall / Cabinet Lights)
Step 10: Connect Wires.
A)
B)
C)
Step 9: Install Strain Relief.
A) Feed LIN connector thru strain relief (provided)
and bottom cover.
B) Install strain relief into bottom cover.
Connect LIN wires to quick disconnects.
Route LIN wires to base of chair as
required by facility.
Go to Last Page in this instructions to
see LIN connection to Elevance Chair.
TP201 Rev. A
DA
Quick
Disconnects
LIN
Strain
Relief
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-11
Style G
i
Color Page
LIN Connector
from Light
Step 1:
Remove covers.
A) Release two clips using a flat head screw driver.
B) Pull upper lift arm cover up to free it from shaft.
C) Remove two screws and metal PC Board cover.
Step 2: Connect Wires.
TP201 Rev. A
A) Insert LIN connector wires into terminal block
TB1 as shown on PC Board.
© 2013 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-12
Style G