WPLSERIES
Die Cast Aluminum Wall Pack
EZ5® Mounting System
for Recessed or Surface Power Supply
LED
SPECIFICATIONS
Housing
Die cast aluminum housing.
Hinged door frame with two captive
lock-up screws, one-piece silicone
self -attaching door sealing gasket,
seals door frame to housing. See
Finish.
Reflector
Aluminum finished high gloss white
(90% reflectance) polyester powder coat . See Finish
Lens
WPL: Impact resistant borosilicate
prismatic glass, silicone caulked to
door frame. WPDL: Impact resistant clear tempered glass, silicone
caulked to door frame.
LED
CREE CXA2540 chip on board
LED array. 3500 and 5000k, 80
CRI. 4000k is 70 CRI. RoHScompliant, UL-recognized component. See table.
Dimmable LED Driver
Class 2, Outdoor Type 1. Input
power 55 watts @ 120v, 54 watts
@ 277v, output current 1050mA.
No PCBs, IP66, Input/Output Isolation, FCC Title 47 CFR Part 15,
Surge Protection (2 KV), Open/
Short Circuit Protection. Class A
sound rating. Dimming control 0-
10v, dimming range 10 to 100%.
Photometric Information
Contact factory.
EZ5® Wall Mount System for
Recessed Power Supply
One-piece cast aluminum bracket.
Cast aluminum, wall mounting
plate with 1/4" thick neoprene gasket. Quick disconnect wiring harness. Esco’s EZ5® Mounting Sy stem allows the contractor to install
the fixture in 5 minutes or less.
Finished same as housing. See
finish note.
EZ5® Wall Mo unt System for
Surface Power Supply
External 16 GA. mounting flange
provided with four 1/2” x 3/4” key hole mounting slots for fixture installation. External junction box.
Quick disconnect wiring harness.
Esco’s EZ5® Mounting System
allows the contractor to install the
fixture in 5 minutes or less. Finished same as housing.
Finish
Detergent cleaned with iron phosphate and chromic acid rust inhibitor.
Chip resistant powder urethane polyester coating, electrostatic applied and baked. Standard
color textured bronze. Custom
colors are available. Consult factory or sales representative.
Fixture Warranty
The fixture mechanics are guaranteed to be free from defective material and workmanship, under
normal installation and operating
conditions, for ten years from date
of shipment from the factory. The
lighting system is warranted for five
years, when properly installed and
under normal conditions of use.
Warranty does not cover lens. See
General Terms and Conditions.
Energy Data
43.3°C (110°F) Max. Temperature,
120-277V/50/60Hz, Constant Current, -40°C Min. Temperature, 90°C
Max. T case Temperature.
Certifications and Labels
Wall mount suitable for wet loc ation, ETL, CETL listed and I.B.E.W.
assembled and labeled.
WPDL Recessed Power Supply
Dimensions with EZ5® Mounting System
for Recessed Power Supply
WPLR
Dimensions with EZ5® Mounting System
for Surface Power Supply
WPDLR
14-1/8”
WPLS
18-9/16”
8”
X
9”
5”
WPL Surface Power Supply
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT
NOTICE
DIMENSIONS
8”
X
5”
WPL Recessed Power Supply
8”
X
5”
WPDLS
12-3/4”
17-1/4”
9-7/8”
10-1/2”
10-1/2”
WPDL Surface Power Supply
18”
19-5/8”
18”
19-5/8”
WBE City of Chicago Certified
3 2 5 4 N o r t h K i l b o u r n A v e n u e C h i c a g o , I l l i n o i s 6 0 6 4 1 -4 5 0 5
P h o n e : 7 7 3 -4 2 7 -7 0 0 0 F a x : 8 0 0 -2 1 7 -1 2 6 0 w w w . e s c o l i g h t i n g . c o m
Established 1 975
5/14
HOW TO ORDER
Catalog
Number
Mounting
System
System Color
Watts Temp
WPL16310R
EZ5® Recessed power
supply mounting system
EZ5® Recessed power
WPL16410R
supply mounting system
EZ5® Recessed power
WPL16510R
supply mounting system
37W
37W
37W
3500K
4000K
5000K
CRI
Initial Lumens
80
4730
70
5083
80
5435
System Color
Watts Temp
Initial Lumens
Catalog
Number
Mounting
System
4230
WPDL16310R
EZ5® Recessed power
supply mounting system
37W
3500K
80
4730
4230
4545
EZ5® Recessed power
WPDL16410R
supply mounting system
37W
4000K
70
5083
4545
4860
EZ5® Recessed power
WPDL16510R
supply mounting system
37W
5000K
80
5435
4860
4230
EZ5® Surface power
WPDL16310S
supply mounting system
37W
3500K
80
4730
4230
@25°C @85°C
CRI
@25°C @85°C
WPL16310S
EZ5® Surface power
supply mounting system
WPL16410S
EZ5® Surface power
supply mounting system
37W
4000K
70
5083
4545
EZ5® Surface power
WPDL16410S
supply mounting system
37W
4000K
70
5083
4545
WPL16510S
EZ5® Surface power
supply mounting system
37W
5000K
80
5435
4860
WPDL16510S
EZ5® Surface power
supply mounting system
37W
5000K
80
5435
4860
WPL26310R
EZ5® Recessed power
supply mounting system
74W
3500K
80
9460
8460
WPDL26310R
EZ5® Recessed power
supply mounting system
74W
3500K
80
9460
8460
9090
EZ5® Recessed power
WPDL26410R
supply mounting system
74W
4000K
70
10166
9090
9720
EZ5® Recessed power
WPDL26510R
supply mounting system
74W
5000K
80
10870
9720
8460
EZ5® Surface power
WPDL26310S
supply mounting system
74W
3500K
80
9460
8460
74W
4000K
70
10166
9720
EZ5® Surface power
supply mounting system
74W
5000K
80
10870
9720
EZ5® Recessed power
WPL26410R
supply mounting system
EZ5® Recessed power
WPL26510R
supply mounting system
37W
74W
74W
3500K
4000K
5000K
80
70
80
4730
10166
10870
WPL26310S
EZ5® Surface power
supply mounting system
WPL26410S
EZ5® Surface power
supply mounting system
74W
4000K
70
10166
9720
EZ5® Surface power
WPDL26410S
supply mounting system
WPL26510S
EZ5® Surface power
supply mounting system
74W
5000K
80
10870
9720
WPDL26510S
74W
3500K
80
9460
ACCESSORIES AND OPTIONS
Photo Control * Suffix Catalog number with
120 Volt = PC4
208-277 Volt = PC5
Example: WPL265 becomes WPL265PC4
Occupancy Suffix Catalog Number With
Sensor* 360° 48’ coverage at 8’ height = OS2
360° 40’ coverage at 20’ height = OS3
Example: WPL265 becomes WPL265OS3
Fuse and Suffix Catalog Number With F
Fuse Holder * Example: WPL265 becomes WPL265F
*120 or 277 volt must be specified when ordering a Photo Control or Fuse and Fuse Holder.
Voltage Suffix 120v = -1, 277v = -4
EXAMPLE ORDER: WPDL26310S = 74W, 3000K, with EZ5® surface power supply mounting system.
EZ5® INSTALLATION INSTRUCTIONS
Recessed Power Supply Installation
Step 1. Connect quick
connector to power
supply.
Step 2. Attach cast
aluminum mounting
plate on recessed
j-box.
Step 3. Connect quick
connector from power
source to fixture.
Step 4. Hang wall pack
on mounting plate.
Step 5. Secure wall
pack to mounting plate
with locking screw.
Step 3. Hang wall pack
using key slots.
Step 4. Secure to wall.
Step 5. Connect wall
pack to external j-box.
Surface Power Supply Installation
Step 1. Mark wall with
supplied template.
Step 2. Start fasteners
in wall.