D-16500-001-A
Bill Hussey
7/16/2015
Town of Greenwood
Water Treatment Plant
Electrical
16500 Lighting
Submittals
By
Feazel Electrical Contracting - Electrical Contractor
For
Max Foote Construction - General Contractor
BALAR Associates, Inc-Consulting Engineers
93
FULLY ENCLOSED INDUSTRIAL – 6” DEEP
SUBMITTAL:
JOB:
GREENWOOD WATER TREATMENT PLANT
TYPE:
93
EXAMPLE
VOLTAGE:
S1E
-
t SERIES
4
t
NOMINAL
LENGTH
-
2 32
t
t
TOTAL WATTAGE/
LAMPS TYPE
-
A
-
OP TIONS
t
SHIELDING
-
E B2
t
-
t
OPTIONS/
ACCESSORIES
UNV
t
BALLAST
TYPE
VOLTAGE
COMPONENT
FEATURES
Captive suitcase type latches ensure tight seal and reduce
installation time and maintenance.
XX
NSF/ANSI Standard 2­– Splash Zone certified.
XX
UL listed as fluorescent fixture suitable for wet location 1
when ordered with factory-installed watertight hubs.
XX
Dust and moisture resistant.
XX
Seamless thermo-set polyurethane gasket poured and
formed in place to ensure tight seal.
XX
Ballast(s) secured by two captive bolts and nuts to ensure a
tight, reliable fit for maximum heat dissipation.
XX
This fixture is proudly made in the USA.
XX
ø7/8” KO location
with snap-in cap
5-7/8”
7”
ORDERING INFORMATION
SERIES
OPTIONS/ACCESSORIES (Continued)
93
Fully Enclosed Industrial–6” Deep
NOMINAL LENGTH
4
8
4’
8’
TOTAL LAMPS
1, 2, 3, 4, or 6
(1-, 2-, or 3-lamp cross-section)
LAMP WATTAGE/TYPE
28T5S
32
54T5H
59
86
DR
PC
TP 2
SS LATCH
TP/SS LATCH 2
TP/PC LATCH 2
SSMB
Injection-molded tamper-resistant latches 2
Stainless steel latches
Tamper-resistant stainless steel latches 2
Tamper-resistant polycarbonate latches 2
Stainless steel ceiling mounting brackets
(2 per fixture)
SSMB/VBY/__ Stainless steel mounting brackets with
Y-hangers and suspension chain (2 per
fixture) (specify length of chain)
4’, 28-watt T5 (1- or 2-lamp ballast[s] only)
4’, 32-watt T8
4’, 54-watt T5HO (1- or 2-lamp cross-section only)
8’, 59-watt T8 (1- or 2-lamp cross-section only)
8’, 86-watt T8 (1- or 2-lamp cross-section only)
BALLAST TYPE
High-impact clear acrylic with internal stipple
(standard)
50% DR high-impact diffuser
100% polycarbonate diffuser
VOLTAGE
SHIELDING
A
T5 | T8
93-4-332-A-WET/2-SSLATCH-SSSMB-EM5U/2-EB3-VOLT-GLR
OPTIONS/ACCESSORIES
EB1
EB2
EB3
EB4
EB4/2
120
277
UNV
347
1-lamp electronic ballast
2-lamp electronic ballast
3-lamp electronic ballast
4-lamp electronic ballast
(1) 4-lamp and (1) 2-lamp electronic ballast
120V
277V
120-277V
347V
For generic EM ballast options (must specify voltage), see
Fluorescent Information section.1
WET/11
(1) 1/2” watertight hub (factory-installed in end of
housing) 1
1
WET/2
(2) 1/2” watertight hubs (factory-installed in ends
of housing) 1
1
WTT/1
(1) 1/2” watertight hub (factory-installed in back
of housing) 1
1
WTT/2
(2) 1/2” watertight hubs (factory-installed in back
of housing) 1
H.E. Williams, Inc. Carthage, Missouri w w w.hewilliams.com 417-358-4065 Fax: 417-358-6015
November 22, 2011
SPECIFICATIONS
Enclosure – Outer housing
consists of polyester
reinforced fiberglass.
Internal brass studs secure
channel to outer housing.
Internal Housing –
20-gauge die-formed,
ribbed C.R.S.
Latching – Injectionmolded suitcase
type latches.
Reflective Surfaces –
92% minimum average
reflective white polyester
powder coat bonded to
phosphate-free, multi-stage
pretreated metal. All parts
painted after fabrication
to facilitate installation,
increase efficiency,
and inhibit corrosion.
Shielding – High-impact
acrylic with DR additive.
Internal stipple surface
diffuses lamp image.
Electrical – Electronic
ballast standard, instant
start T8, program start
T5, rated Class P.
Mounting – Surface
or suspended.
Labels & Certifications –
UL/CUL listed as
fluorescent luminaire
suitable for dry or damp
locations. UL/CUL listed as
suitable for wet locations
when specified with
WET/_ or WTT/_ option.1
NSF/ANSI Standard 2–
Splash Zone certified.
1
2
When specifying EM option,
EM ballast for enclosed and
gasketed fixtures is required
for fixture to be suitable for
wet locations.
This option requires a
tamper-resistant tool (must be
ordered separately). Please
specify quantity required per
project.
Industrial
Page 44A
93
PHOTOMETRY
Catalog #: 93-4-232-A-EB2
TEST REPORT
INFORMATION
XX
Test Report #: 7853.0
XX
Date: 03/08/94
XX
Lamp Type:
F32T8/735/RS
XX
Lamp Quantity: 2
180° 170°
160°
CANDLEPOWER DISTRIBUTION
150°
45º
90º
0º
982.
982.
982.
5º
988.
992.
999.
90°
15º
999.
1023.
1054.
290.3
90°
25º
879.
942.
997.
434.5
35º
786.
904.
1006.
567.4
45º
594.
770.
913.
589.3
572.6
120°
100°
0°
45º
90º
80°
60°
50°
40°
10°
0°
Zone
Lumens
0 - 30
819.
0 - 40
1387.
0 - 60
2549.
0 - 90
3788.
90 - 120
642.
90 - 130
712.
90 - 150
742.
90 - 180
748.
Total Luminaire:
0 - 180
4535.
20°
30°
% Lamp
14.4
24.3
44.7
66.4
11.3
12.5
13.0
13.1
% Fixture
18.1
30.6
56.2
83.5
14.2
15.7
16.4
16.5
79.6
100.0
Total Luminaire Optical Efficiency: 79.6%
IES Spacing Criteria: Across = 1.5, Along = 1.2
94.6
55º
426.
650.
826.
65º
259.
550.
762.
527.7
75º
123.
460.
622.
437.0
274.1
85º
31.
282.
411.
90º
14.
237.
369.
Ceiling
.80
.70
.50
Wall .70 .50 .30 .70 .50 .30 .50 .30 .10
Zonal
Lumens
0º
130°
70°
LUMEN SUMMARY
Horizontal Angle
Vertical
Angle
140°
ZONAL CAVITY COEFFICIENTS
95º
11.
238.
369.
229.9
105º
11.
155.
442.
251.4
160.6
115º
9.
55.
337.
125º
9.
20.
193.
70.2
135º
9.
15.
60.
20.4
145º
9.
10.
24.
9.8
155º
9.
0.
15.
5.2
165º
0.
0.
0.
.0
175º
0.
0.
0.
.0
180º
0.
0.
0.
Room Cavity Ratio
T5 | T8
FULLY ENCLOSED INDUSTRIAL – 6” DEEP
0
1
2
3
4
5
6
7
8
9
10
.92
.82
.74
.67
.62
.56
.51
.47
.44
.40
.37
.92
.78
.67
.59
.52
.45
.40
.36
.32
.29
.27
.92
.74
.61
.52
.44
.38
.33
.29
.26
.22
.20
.88
.79
.71
.64
.59
.53
.49
.45
.42
.38
.36
.88
.75
.64
.56
.50
.44
.39
.35
.31
.28
.26
.88
.71
.59
.50
.43
.37
.32
.28
.25
.22
.20
.81
.69
.59
.52
.46
.40
.36
.32
.29
.26
.24
.81
.66
.55
.47
.40
.35
.30
.27
.23
.21
.18
.81
.64
.51
.43
.36
.30
.26
.22
.19
.17
.15
Effective Floor Cavity Reflectance = .20
FIXTURE DETAILS
BACK VIEW – 4’ LENGTH
(2) 1/4-28 brass
studs (external)
(2) Drill dimples
38-3/4”
41-1/2”
49-13/16”
BACK VIEW – 8’ LENGTH
(4) 1/4-28 brass
studs (external)
5-1/8”
(2) Drill dimples
40-13/16”
40-13/16”
89-1/2”
97-13/16”
OPTIONS & MOUNTING
Integral 1/4-28
brass stud with nut
and lock washer
“WTT” hub location
(factory-installed option)
“WET” hub location
(factory-installed option)
SSMB
SSMB
Stainless steel mounting bracket
Industrial
Page 44B
H.E . W illiams, In c.
WET_ or WTT_
Watertight hubs
C ar t hage, Mis s our i
Information contained herein is subject to change without notice.
w w w.h ew illia m s.c om
SSMB/VBY
Stainless steel mounting bracket
with Y-hangers
417- 3 5 8 - 4 0 6 5
F a x : 417- 3 5 8 - 6 015
HEWJP43126JJ REV08/15/14
TYPES M1E, S1E & S2E: EM5U/2 JOB: GREENWOOD WATER TREATMENT PLANT
B50
EMERGENCY LIGHTING EQUIPMENT
LowProfile AC and DC output for
T5 and T8 Lamps compatibility
A Division Of Philips Electronics North America Corporation
One- or two-lamp operation;
Universal input voltage:
120 through 277 VAC, 50/60 Hz;
End-of-lamp-life compatible
1.18"
Product Summary
B50
2.2"
UL LISTED FOR US AND CANADA
Factory or Field Installation
(Indoor and Damp)
EMERGENCY LIGHTING EQUIPMENT
13.”
Illumination Time
90 Minutes
APPLICATION
Initial Light Output
Up to 1600 Lumens
The B50 emergency ballast works in conjunction with an AC ballast to convert new or existing fluorescent
fixtures into emergency lighting.The emergency ballast handles a wide range of input voltages and frequencies
and consists of a high-temperature nickel-cadmium battery, charger and electronic circuitry in one compact
galvanized metal case. The B50 can be used with one or two T8,T9,T10,T12 fluorescent lamps. It operates
one 22 - 55 W (2' - 4') T5 lamp, and also including standard, energy saving, HO, VHO, circline, U-shaped and
rapid-start (4-pin) long compact fluorescent lamps. Also operates one 8.5 - 16.5W Philips LED T8
InstantFit lamp: 9290002840, 9290002841, 9290002842, 9290002862, 9290002880, 9290002881,
9290002882, 9290002883, 9290011183, 9290011184, 9290011185, 9290011186, 9290011179,
9290011180, 9290011181, 9290011182. One-or twolamp operation may be selected (see Table 1). It is also
compatible with most single- and multi-lamp electronic and dimming AC ballasts. If used in an emergency-only
fixture, no AC ballast is necessary. The B50 is suitable for indoor and damp locations and for sealed & gasketed
fixtures, including fixtures rated for wet locations. It is not suitable for air handling heated air outlets or wet or
hazardous locations. For information about specific lamp and ballast compatibility, please call the factory.
Recommended applications include: international line voltages from 120 through 277 VAC (50 or 60 Hz);
drilling rigs where generators are the primary source of power; and other applications requiring higher
tolerance of line voltage variation or harmonic distortion.
Full Warranty
5 Years (NOT pro-rata)
Voltage
120 Through 277 VAC, 50 or 60 Hz
AC Input Current
60 mA
AC Input Power Rating
5.0 Watts
Test Switch
2W-ITS (2-wire Illuminated Test Switch)
Battery
High-Temperature, Maintenance-Free
Nickel-Cadmium Battery
7- to 10-Year Life Expectancy
OPERATION
Battery Charging Current
180 mA
When AC power fails, the B50 immediately switches to the emergency mode, operating either one or
two lamps at a reduced lumen output for a minimum of 90 minutes. When the AC power is restored,
the emergency ballast automatically returns to the charging mode and, using a patented circuit,
delays AC ballast operation for approximately three seconds to prevent false tripping of the AC
ballast end-of-lamp-life shutdown circuits.
Recharge Time
24 Hours
Charging Indicator Light
LED
INSTALLATION
Temperature Rating (Ambient)
0°C to +50°C
(32°F to 122°F)
Dimensions
13.31” x 2.2” x 1.18”
(338.1 mm x 55.88 mm x 29.97 mm)
Mounting Center 12.8” (325 mm)
The B50 does not affect normal fixture operation and may be used with either a switched or
unswitched fixture. If a switched fixture is used, an unswitched hot lead must be connected to the
emergency ballast. The emergency ballast must be fed from the same branch circuit as the AC ballast.
The B50 may be installed inside, on top of or remote from the fixture. The emergency ballast may
be remotely installed up to half the distance the AC ballast manufacturer recommends remoting the
AC ballast from the lamp or up to 50 feet, whichever is less. Installation is not recommended with
fixtures where the ambient temperature may fall below 5°C.
Weight
2.7 lbs. (1.26 kg)
UL AND CODE COMPLIANCE
The B50 has been tested by Underwriters Laboratories in accordance with the standards set forth
in UL 924, “Emergency Lighting and Power Equipment,” and CSA C22.2 No. 141, “Emergency
Lighting Equipment.” The B50 is UL Listed for factory or field installation. Emergency illumination
time exceeds the National Electrical Code (NEC), Life Safety Code (NFPA–LSC) and UL 90-minute
requirements.
L2300226
Specifiers Reference
Project
Comments
Type
Model No.
01/16/15 © Philips Emergency Lighting
P.O. Box 460 Collierville, TN USA 38027-0460
Sales 800-223-5728 FAX 901-853-5009
Tech. Support 888-263-4638
www.philips.com/bodine
B50
EMERGENCY LIGHTING EQUIPMENT
LowProfile AC and DC output for
T5 and T8 Lamps compatibility
One- or two-lamp operation;
Universal input voltage:
120 through 277 VAC, 50/60 Hz;
End-of-lamp-life compatible
EMERGENCY ILLUMINATION
Depending on the number (one or two), wattage and type of lamps selected, the B50 produces up
to 1600 lumens initial emergency light output (see Table 2). If two-lamp operation is selected, light
output is evenly divided between the lamps for better distribution of emergency illumination.
Table 1 - Lamp Compatibility
SPECIFICATION
Emergency lighting shall be provided by using a standard fluorescent fixture equipped with
a Philips Bodine B50 emergency ballast. This emergency ballast shall consist of a high-temperature,
maintenance-free nickel-cadmium battery, charger and electronic circuitry contained in one 13.31” x
2.2” x 1.18” galvanized metal case. A solid-state charging indicator light to monitor the charger and
battery, a 2-wire illuminated test switch and installation hardware shall be provided. The emergency
ballast, using a patented circuit, shall delay AC ballast operation for approximately three seconds
to prevent false tripping of AC ballast end-of-lamp-life shutdown circuits. The emergency ballast
shall be capable of operating [one or two] ________ fluorescent lamp(s) (see Table 1) at _________
lumens (see Table 2) initial light output in the emergency mode for a minimum of 90 minutes. It shall
be suitable for indoor and damp locations and for sealed & gasketed fixtures, including fixtures rated
for wet locations. The B50 shall operate at any line voltage from 120 through 277 VAC at frequencies
of 50 or 60 Hz. The B50 shall have 5.0 Watts of input power and a 28.8 Watt-hour battery capacity
and shall exceed emergency standards set forth by the current NEC and CEC. The emergency ballast
shall be UL Listed for installation inside, on top of or remote from the fixture and shall be warranted
for a full five years from date of purchase.
LAMP
BASE
TYPE
(1”, 1¼”, 1½”)
T8,T9,T10,T12
Single
or
Bipin
(DIAMETER)
L2300226
01/16/15 © Philips Emergency Lighting
P.O. Box 460 Collierville, TN USA 38027-0460
Sales 800-223-5728 FAX 901-853-5009
Tech. Support 888-263-4638
www.philips.com/bodine
(Length)
17 - 40 W
(2'-4')
NO. of LAMPS
BROWN
VIOLET
(EMERGENCY) CONNECTOR CONNECTOR
1
CLOSED
OPEN
2
OPEN
CLOSED
40 - 215 W
(5' -8')
1
OPEN
CLOSED
18 - 39 W
1
CLOSED
OPEN
40 - 55 W
1
CLOSED
OPEN
TWIN/QUAD/TRIPLE
4-PIN
TWIN-TUBE
13 - 42 W
(G24q, Gx24q)
COMPACT
LONG COMPACT
T5 & T5 HO
2D
4-PIN (2G11)
1
CLOSED
OPEN
MINIATURE
BIPIN
14 - 54 W
(2'-4')
1
CLOSED
OPEN
HO CIRCLINE
22 - 55 W
1
CLOSED
OPEN
4-PIN (GR10q) 16 - 55 W
1
CLOSED
OPEN
1
CLOSED
OPEN
Philips LED T8
InstantFit
WARRANTY
Model B50 is warranted for five (5) full years from date of purchase. This warranty covers only
properly installed Philips Bodine emergency ballasts used under normal conditions. For the
warranty period, Philips Emergency Lighting will, at its option, repair or replace without charge a
defective emergency ballast, provided it is returned to the factory transportation prepaid and our
inspection determines it to be defective under terms of the warranty. Repair or replacement, as stated
above, shall constitute the purchaser’s exclusive warranty, which does not extend to transportation,
installation, labor or any other charges; nor does it apply to any equipment of another manufacturer
used in conjunction with the emergency ballast.
WATTAGE
Bipin
8.5 - 16 .5 W
Table 2 - Initial Lumen Output
LAMP
LUMENS
1 Lamp
F14T5/HE
839
F21T5/HE
1245
F28T5/HE
1582
F24T5/H0
873
F39T5/H0
1395
F54T5/H0
1401
2 Lamps
FC9T5 22W Circline
812
F12T5 40W Circline
1194
FC12T5 55/W Circline
1183
F17T8
511
792
F25T8
903
1223
F32T8
1069
1460
F40T8
762
F96T12/H0 110W
1100
PL-L 24W
762
PL-L 36W
1100
PL-L 40W
1174
PL-L 55W
1430
PL-T 26W
858
PL-T 32W
877
PL-T 42W
991
Philips LED T8InstantFit 14.5 W
892
Philips LED T8InstantFit 16.5 W
1053
Test results at 25°C, lamp-loads are new fresh model
lamps.
For the most current technical information and notices, please visit TechNotes on our website.