)NDIVIDUAL3ILICON3URGE
3UPPRESSIONFOR4O6$#AND
,OW6OLTAGE6!#!PPLICATIONS
Todayʼs technology involves sensitive electronic equipment which
you depend upon for systems reliability. Your valuable electronic
systems will experience unpredictable and potentially destructive
power quality conditions such as lightning and transients which
cost your business maintenance time, equipment replacement and
customer dissatisfaction. Our I2R ICP Series features our proprietary
silicon avalanche suppressor diode (SASD) technology for effective
safeguarding and maximized performance of your systems.
In
addition, it provides remote status monitoring and plug-in modules.
Your success demands a superior protection solution provided by
Transtector Systems.
!PPLICATIONS
• Telecom Power Systems
• Communications Hubs, Nodes
• Digital Loop Carries
• Cabinets/Load Centers
• Din Rail Mounts
• Solar & Turbine
)2)#03ERIES$#
)NDIVIDUAL3ILICON3URGE3UPPRESSION
&OR4O6$#AND,OW6OLTAGE6!#!PPLICATIONS
• 100% silicon suppression
• Plug-in suppression modules with status
indicators
• Designed to standard 35mm DIN Rail profile
and compact footprint
Nominal Service
12V
24V
48V
Protection Levels*
36V
58V
90V
Current Ratings
2kA
2kA
2kA
Operating Temperature
-30 º C to +65 º C
Response Time (Max.)
<5 Nanoseconds
Part Number 1101-624
• Mountable without DIN Rail
*
• Remote status monitoring capability
DC
+
������
-
Figure 1
I2R ICP
Common
3. Wiring the I2R ICP Series: Unplug Suppressor Module from
base. Install 4-14 AWG into base per Figure 1 or 2 keeping
leads as short as possible.
Typical Application
4. Insert Suppressor Module into Base Unit.
5. Optional Wiring for Remote Status Indication (see Figure 4)*
5.1 Use test plug included in packaging.*
5.2 Wire with respect to opposite rail as indicated by voltage potential
in Figure 4.
5.3 Maximum continuous current for remote status not to exceed .5A.
Remote Lamp
Indicator
On = Protected
Voltage Potential
Output Plug Included
REMOTE
2. Mounting the I2R ICP Series
2.1 35 mm DIN Rail Mount (see Figure 3)
2.2 Screw Mount (see Figure 4)
Figure 2
Multiple Unit Wiring Diagrams
Remote Status
Indication Plug
I2R ICP Series - For IEEE Locations A and B Per C62.41-1991
1. Warning! Disconnect power upstream from the device when wiring to
avoid potential shock hazard. Unit must be installed within an enclosure.
It is recommended that a 15 or 20A current limiting fuse be installed in
series with each I2R ICP. Example Bussmann KTK 15 or KTK 20.
Low Voltage VAC
������
Figure 1
Base Unit
2.6”H X 1.09”W X 2.64”L
6.6 cm X 2.8 cm X 6.7 cm
Installation
I2R ICP
L
Dimensions
Five (5) year unconditional warranty
Ten (10) year manufacturer warranty
Single Phase Wiring Diagrams
MOUNTING OPTION
1101-626
Voltage protection level determined at 6kV 500A.
Warranty
• UL and CSA approved and designed to
meet IEC specifications
1101-625
I 2R ICP Series - DC
Configurations
Features
6. Turn power on. LED illumination indicates power is supplied and
suppression is enabled.
WARNING!!! REMOTE STATUS CONTACT IS ENERGIZED. LIVE
ELECTRICAL POWER EVEN WITHOUT LED ILLUMINATION.
STATUS
Figure 4
Suppressor Module
208.772.8515 800.882.9110 FAX 208.762.6133
10701 N. Airport Road, Hayden, ID 83835
www.transtector.com
sales@transtector.com
An ISO 9001:2000 and 14001 Certified Company
1452-011 Rev.B