Flame Sensors
C7012 Solid State Purple Peeper® Ultraviolet Flame Detectors
C7012A,E
C7012C,F
Solid state electronic flame detectors for use with Honeywell Flame
Safeguard controls and amplifiers. Sense ultraviolet radiation
produced by combustion of gas, oil, coal or other fuels.
APPROVALS:
Underwriters Laboratories Inc. Listed: 120V models only: C7012A
and E (except C7012E1161): File No. MP268, Guide No. MCCZ;
C7012C,F: File No. E34649, Guide No. ZTSZ.
Canadian Standards Association Certified: 120V models only:
C7012A and E: Master File LR95329-1.
Factory Mutual Approved: Report No. 14740.01.
Industrial Risk Insurers Acceptable.
MOUNTING:
C7012A,E: Mounting flange with either 3/4 in. or 1 in. NPT internal
threads (depending on model) for attaching to sighting pipe.
C7012C,F: Pipe union with 1 in. NPT internal threads for attaching to
sighting pipe.
DIMENSIONS, APPROXIMATE:
Lead Length: 8 ft. (2.4 m).
ELECTRICAL RATINGS:
Power Consumption:
C7012A,C: 2.5W.
C7012E,F: 7.0W.
REPLACEMENT PARTS:
All models:
113228 Ultraviolet Sensing Tube.
191286 Ultraviolet Sensing Tube—for operation to -40 F (-40 C)
outside case.
C7012A and E:
114372 Quartz Viewing Window, rated for 20 psi (137.9 kPa).
114465 Gasket, silicone rubber—for installing viewing window
(3 required).
120739 Gasket, fiber-neoprene—heat insulation and seal-off for
mounting flange.
C7012C and F:
122037 Quartz Viewing Window, rated for 100 psi (689.5 kPa).
C7012E and F:
190971B Coil and Shutter Assembly—for all models except
220V/50 Hz.
Dimensions of C7012A,E in in. (mm in brackets).
MOUNTING FLANGE
3/4–14 NPT
7-7/32
(183)
5-1/8 (130)
3-3/4
(95)
3-7/16
(87)
1/2–14 NPSM
5-1/4 (133)
LEADWIRES
FACEPLATE
C7012A,C,E,F
M1962B
Dimensions of C7012C,F in in. (mm in brackets).
1–11 1/2 NPT
FACEPLATE
PIPE
UNION
1(25)
8
(203)
DIA.
1
2
(38)
1
1/2–14 NPT
1
16
(52)
LEADWIRES
2(51)
9 (229)
M1963
5
(127)
2
3 (76)
2
(51)
5/16–18 UNC–2B BY
7/16 (11) DEEP
MOUNTING HOLES (2)
continued next page
747
Flame Safeguard Controls
• Replace C7012 vacuum tube models.
• Mount horizontally, vertically or at any angle in between.
• Provide quick electrical hookup with threaded conduit fitting and colorcoded leadwires.
• Reduce nuisance shutdowns by wiring two in parallel.
ACCESSORIES:
All models:
117053 Meter Connector Plug (for older W136A models).
118367A Swivel Mount.
118369 Bushing, galvanized iron, with 3/4 in. NPT internal
threads on one end and 1 in. NPT external threads on other
end. For adapting detector with 1 in. NPT internal threads (for
mounting) to a 3/4 in. sighting pipe, or to pipe nipple and tee
for connecting air supply.
W136A Test Meter (includes 196146 Meter Connector Plug).
C7012A and E:
120934 Mounting Flange, aluminum, with 3/4 in. NPT internal
threads for attaching to sighting pipe.
122748 Quartz Viewing Window, rated for 50 psi (344.7 kPa).
123539 Antivibration Mount.
124198 Mounting Flange, aluminum, with 1 in. NPT internal
threads for attaching to sighting pipe.
124204 Quartz Magnifying Lens, rated for 20 psi (137.9 kPa); for
increasing the ultraviolet radiation sensed by the detector.
115594A Seal-off Adapter, rated for 100 psi.
190105 Water Jacket.
Flame Sensors
C7012 continued
Available only through Honeywell Authorized Flame Safeguard Distributors.
Electrical
Ratings,
Power Supply
ORDER NUMBER
Application
C7012A1145
Use with Honeywell
rectification-type
flame safeguard
controls EXCEPT
Dynamic Self Check
modelsc. Fieldreplaceable viewing
window and
ultraviolet sensing
tube.
C7012A1152
C7012A1160
C7012A1186
C7012A1194
C7012C1042a
C7012E1104
C7012E1112
C7012E1120
C7012E1146
C7012E1153
C7012E1161b
C7012E1278d
Use only with
Dynamic Self Check
flame safeguard
controlsc. Fieldreplaceable viewing
window, ultraviolet
sensing tube, selfchecking coil and
shutter.
a
C7012F1052
Pipe
Mounting
Size
Temperature Ratings,
Ambient
F
C
Enclosure
120 Vac 50/60 Hz 3/4 in. NPT +25 to +175 -4 to +79
120 Vac 50/60 Hz 1 in. NPT
+25 to +175 -4 to +79
120 Vac 50/60 Hz 1 in. NPT
-40 to +175
-40 to +79
208 Vac 50/60 Hz 3/4 in. NPT +25 to +175 -4 to +79
240 Vac 50/60 Hz 3/4 in. NPT +25 to +175 -4 to +79
120 Vac 50/60 Hz 1 in. NPT
+25 to +175 -4 to +79
120 Vac 50/60 Hz 3/4 in. NPT -20 to +175
-29 to +79
120 Vac 50/60 Hz 1 in. NPT
-20 to +175
-29 to +79
120 Vac 50/60 Hz 1 in. NPT
-40 to +175
-40 to +79
208 Vac 50/60 Hz 3/4 in. NPT -20 to +175
-29 to +79
240 Vac 50/60 Hz 3/4 in. NPT -20 to +175
-29 to +79
120 Vac 50/60 Hz 1 in. NPT
-29 to +79
-20 to +175
120 Vac 50/60 Hz 1 in. NPT
-20 to +175
-29 to +79
120 Vac 50/60 Hz 1 in. NPT
-20 to +175
-29 to +79
Violet, cast-aluminum cover; mounting
flange (with heat block) and faceplate are
separate to provide heat insulation and
seal-off. Meets NEMA 4 standards
(water-tight and dust-tight indoor and
outdoor).
Explosion-proof, 2-piece, violet,
cast-aluminum.
Violet, cast-aluminum cover; mounting
flange (with heat block) and faceplate are
separate to provide heat insulation and
seal-off. Meets NEMA 4 standards
(watertight and dust-tight, indoor and
outdoor).
Explosion-proof, 2 piece, violet, castaluminum.
a
With explosion-proof housing for use in hazardous atmospheres.
With 10 ft (3.0 m), 5-wire cable with amp connector.
c
Dynamic Self Check controls are R4075C,D,E; R4138C,D; R4140, BC7000 with R7247C Amplifier, BCS7700 with R7747C Amplifier or 7800
SERIES with R7847C Amplifier.
d Includes Brad Harrison® type Number 41310 connector. Mating connector can be Brad Harrison® 41306N or 41307N type connector.
b
C7013, C7014 Rectifying Photocells and Mounts
C7014A
C7013A
Compact flame detectors for installation inside the blast tube of oil
burners.
• Use with Honeywell Flame Safeguard programmers and burners
requiring photocell flame detection.
• Mount below burner nozzle in the blast tube to provide a reliable
detection of the oil flame.
• Use Rajah connectors on the case which provide a service-free
electrical connection to transmit the photocell current to the flame
safeguard control.
• Field-replaceable 38316 Photocell.
APPROVALS:
Underwriters Laboratories Inc. Listed: File No. MP268, Guide No.
MCCZ.
Canadian Standards Association Certified: Master Report
LR95329-1.
Factory Mutual Approved: Report No. 24181.03.
Industrial Risk Insurers Acceptable.
TEMPERATURE RATINGS:
Ambient: 165 F (74 C) maximum at photocell.
REPLACEMENT PARTS:
101851-00020 Rajah Connector, socket end—C7014A only.
38316 Photocell.
ACCESSORIES (C7013A only):
121610 Magnifying Lens.
38242 Rajah Connector (plug end).
38570 Holder for filter and magnifying lens.
38576 Filter—used to reduce heat or effect of hot refractory on
photocell.
Available only through Honeywell Authorized Flame Safeguard Wholesalers and Distributors.
Dimensions, Approximate
Width
ORDER NUMBER
Application
Use With
in.
C7013A1003
Used with conventional pressureatomizing oil burners; used in high
humidity areas.
Stud terminal Rajah
Connector
C7014A1002
Used with Shell Head oil burners.
Spring-snap terminal Rajah
Connector
748
mm
Height
Depth (incl. connector)
in.
mm
in.
mm
1-1/4 32
2
51
1-5/8
41
13/16 21
1-3/4
45
2-1/4
57