4. BODY 39 ROCKER PANEL 1/25 SCALE A742-200 5 HEADLINER 1 COUPE BODY (To bosses) (Completed Chassis) Carefully install completed chassis/interior assembly into completed body. Ensure the 4 chassis mounting post pins are fully seated into bosses inside body. Install rocker panels to completed body/chassis. IMPORTANT 38 ROCKER PANEL 5. FINAL ASSEMBLY 11 Decal DECAL Paper Backing 20 8 37 RIGHT HEADLIGHT BEZEL 43 RIGHT HEADLIGHT LENS (Clear) 7 42 LEFT HEADLIGHT LENS (Clear) 7 DECAL 4 12 HOOD 18 40 WINDSHIELD (Clear) 52 RIGHT TURN LIGHT 63 COWL 24 53 22 25 RIGHT MIRROR 13 GRILLE 35 ANTENNA DECAL APPLICATION INSTRUCTIONS 1. Cut decals apart close to image. Apply one at a time. 2. Dip decal into tepid water until paper backing loosens. 3. Moisten area of model where decal is to be applied, to aid in positioning. 4. Slide decal partly off of paper backing. 5. Place decal on model face up and slide paper backing away. 6. Thoroughly blot out excess water, air bubbles, and any excess emulsion with soft, lint-free cloth. 7. Allow time to dry before handling. NOTE: If air bubbles or wrinkles form on an irregular or curved surface, cut decal and press into place. Painting: Wash parts thoroughly with mild soap and water. Parting lines, glue joints, and sharp edges should be sanded or filled with filler putty designed for plastic. Apply a "primer" coat and allow to dry. Check parts for imperfections and repeat the procedure if necessary. Remove any lint or dust. Apply paint evenly, in several thin coats rather than one heavy coat. Allow each coat to thoroughly dry before the next is applied. Each coat should be carefully “wet sanded” using slightly damp No. 1200 sandpaper. Be careful not to remove any detail white sanding. Lightest colors should be painted first. Use frosted tape to mask off areas not to be painted. Remove tape after paint is dry to the touch. Use a very fine brush to touch up edges. Decals: See back of instruction sheet for proper application. Decals should to be added after applying a gloss coat. Apply a final clear coat after decals are dry. 41 REAR WINDOW 8 DECAL (Repeat for other side.) 14 13 DECAL DECAL (Repeat for other side.) (Repeat for other side.) International Hobbycraft (UK) Ltd. 21 St. Thomas Street Bristol BS1 6JS England 3 Part Number Completed Assembly RECOMMENDED PAINT COLORS Aluminum Gloss Black Clear Red DECAL Silver Flat Black Red Amber Semi-Gloss Black 3 2 1 DECALS: See back of instruction sheet for application instructions. Many of the very small decals in this kit have been included in duplicate to serve as backups, should any get lost or otherwise compromised during application. DECAL DECAL 0 4 7768 9 5 DECAL MPH 7:33 RPM X1000 DECAL 6 DECAL MPH 74 0 F DECAL 99.1 C H E F FM FAV 2 DECAL 45 23 24 LEFT MIRROR 47 7 48 LEFT SIDE WINDOW DECAL 15 (Repeat for other side.) DECAL (Optional) GENERAL MOTORS Trademarks used under license to Round 2, LLC. Other names and trademarks used under license to Round 2, LLC or by permission. AMT and SHOWROOM REPLICAS are trademarks of Round 2, LLC. ©2012 Round 2, LLC, South Bend, IN 46628 USA. Product and packaging designed in the USA. Made in China. All rights reserved. White REFER TO BOX ART PHOTOS FOR PAINTING DETAILS IMPORTANT: Apply decals to seats, dashboard and steering wheel BEFORE assembling parts in Section 3/INTERIOR. BE SURE TO PAINT THE DESIRED PARTS FIRST AND ALLOW THEM TO DRY FULLY BEFORE APPLYING DECALS. (Optional) DECAL Apply Decal DECALS: See application instructions. All decals have been included in duplicate to serve as backups, should any get lost or damaged during application. 1. DETAILING DECALS DECAL 12 49 DECAL 19 10 53 FRONT FASCIA 2 FOG LIGHT (To body) LENSES (Clear) (Repeat for other side.) DECAL 1 Assembly Sequence DECALS MUST BE APPLIED TO CERTAIN PARTS AFTER PAINTING BUT PRIOR TO ASSEMBLY. SEE SECTION 1. 21 Round 2, LLC 4073 Meghan Beeler Court South Bend, IN 46628 Assembly: Carefully study and understand the entire instruction sheet. Compare the parts in the box to the instruction sheet to be sure you have received all the parts required. Carefully remove parts from trees. Before cementing, "TEST FIT" parts together to insure proper location and alignment. Scrape paint and plating from surfaces to be cemented. Subassemblies and components should be painted before any parts are attached. Use only cement and paint made for styrene plastic. 14 SPOILER 51 LEFT TURN LIGHT ™ SYMBOLS 49 RIGHT SIDE WINDOW 36 LEFT HEADLIGHT 5 BEZEL (Repeat for other side.) USA-1 2010 CHEVY CAMARO SS/RS COUPE ® 2 11 REAR FASCIA (To body) 46 44 4 TAILLIGHT LENSES (Clear) 10 DECAL (Optional) 19 STEERING WHEEL 22 DASHBOARD SEATS (Vinyl) 2. WHEELS & CHASSIS 3. INTERIOR IMPORTANT: Apply decals to seats, dashboard and steering wheel as shown in SECTION 1, before assembling parts. 23 SHIFTER KNOB (To hole) 32 FRONT WHEEL (Chrome) x 2 34 REAR DECK 21 PARKING BRAKE HANDLE (To hole) 4 FLOOR PAN 3 CHASSIS 20 CONSOLE Applicare lo pneumatico alle ruote, assicurandosi che sia ben inserito. 57 FRONT TIRE (SMALL) x 2 33 REAR WHEEL (Chrome) (LARGE/WIDE) x2 Locate interior to chassis by inserting pins on top side of chassis into holes in bottom of interior. Large upright slats on chassis slide into openings below the front seats. 58 REAR TIRE (LARGE/WIDE) x 2 18 EXHAUST TIP 26 EXHAUST PIPES 17 EXHAUST TIP NOTE: Wheels not shown for clarity. 11 NOTE: Ensure correct disc brake part numbers are used for each wheel. Each disc brake has a tab which locks into the chassis, to position its caliper correctly. Apply cement to tabs only, so that axles may rotate inside. 7 RIGHT DOOR PANEL 15 (Completed Wheel) TAB NOTE: Work completed wheels firmly onto axles. 14 9 60 RIGHT FRONT ROTOR TAB 20 55 SEAT (Vinyl) 22 DASHBOARD (Completed Wheel) 8 TAB NOTE: Work completed wheels firmly onto axles. 13 METAL AXLE 11 12 (Completed Wheel) 59 LEFT FRONT ROTOR OUTSIDE OUTSIDE 16 RIGHT 61 LEFT REAR ROTOR METAL AXLE (Completed Wheel) LEFT TAB 18 17 (Viewing from above) 6 LEFT DOOR PANEL 7 56 SEAT (Vinyl) 27 EXHAUST PIPE SUPPORT TIRES ARE DIRECTIONAL 10 62 RIGHT REAR ROTOR 54 SEAT (Vinyl) 5 30 TRANSMISSION SUPPORT FORWARD ROLL 19 19 STEERING WHEEL 15 MUFFLER 10 16 MUFFLER