Doc. 15.181.00
TOYOTA
PIO / DIO
Tundra
12/05/13
2014
Vehicle Remote Start System
Part Number: 00016-34043
Accessory Code: QR10
Vehicle Service Parts
TMS Remote Start
Kit Contents
Item #
Qty
Description
1
1
Remote Start Module w/ DNA Software
2
1
Main Wiring Harness
3
1
2-Way IVU Antenna
4
1
2-Way IVU Antenna Harness
5
1
Immobilizer Interface Module
6
1
Owner’s Manual
7
1
Hardware Bag
8
1
2-Way Transmitter
9
4
Large Cable Ties
10
1
Hood Pin Switch Kit
11
1
Key Tag
(May be required for reassembly)
Part Number
Qty
00016-34035-01
1
2-Way Antenna Harness
Description
00016-34035-02
1
Main Wiring Harness
00016-34035-03
1
Hardware Bag
00016-34035-04
1
2-Way Antenna
00016-34035-05
1
Immobilizer Interface Module
00016-34035-06
1
2-Way Transmitter
00016-34035-07
1
Removable Software Card
00016-34035-08
1
Main Module
00016-08032-09
1
Hood Pin Switch Bracket
00016-08032-10
1
Hood Pin Switch
00016-34035-11
2
Red Scotch-Lok Connector
00016-34035-12
6
8” Wire Ties
00016-34035-14
1
Dielectric Grease
00016-08032-11
1
Hood Pin Switch Harness
00016-34035-16
1
Key Tag
Hardware Bag Contents
Item #
Qty Reqd.
Description
1
15
8” Black Cable Ties
2
1
Foam Pad
3
1
Underhood Label
4
10
Black T-Taps
5
1
Red T-Tap
6
1
Blue T-Tap
7
General Applicability
Legend
STOP
8
STOP: Damage to the vehicle may occur. Do not
proceed until process has been complied with.
OPERATOR SAFETY: Use caution to avoid risk of
injury.
Safety Tools
CRITICAL PROCESS: Proceed with caution to
ensure a quality installation. These points will be
audited on a completed vehicle installation.
Special Tools
TOOLS AND EQUIPMENT: This calls out the specific tools and equipment required for this process.
Recommended Tools
!
REVISION MARK: This mark highlights a change in
installation with respect to a previous issue.
Installation Tools
Phillips Screwdriver
Straight-Slot Screwdriver
Ratchet w/ Extension
10 mm Socket
Diagonal Wire Cutters
Common Pliers
Flashlight
Nylon Trim Tool
Torque Wrench (48 in. lbs.)
Special Chemicals
VPC Approved Cleaner
S
SAFETY TORQUE: This mark indicates that torque
is related to safety.
SPECIAL NOTE:
After TMS and Safety mandated preparatory steps have been
taken, the installation sequence is the suggested method for
completing the accessory installation. In some instances the suggested sequence is written for one associate to install and in others the sequence is given as part of a team accessory installation.
Unless otherwise stated in the document, the associates may
perform the installation steps in any order to make the installation
as efficient as possible while maintaining consistent quality.
Rev. - 12/3/13
2014
Tundra
INSTALLATION PREPARATION
Vehicle Remote Start System
Negative Battery
Cable
Before starting installation:
1. Familiarize yourself with the installation
instructions.
2. Inspect the kit components (Refer to Kit
Contents and Hardware Bag Contents).
VEHICLE PREPARATION
1. Place protective coverings on vehicle.
! 2. “IMPORTANT......IMPORTANT”
Disconnect Negative Battery Cable.
Regular Cab
3. Remove the driver’s side front door step
sill panel.
Regular Cab:
Disengage the (6) claws and (3) clips.
Double Cab:
Disengage the (6) claws and (3) clips.
Double Cab
4. Remove the driver’s front kick panel, by
removing the (1) plastic retaining nut and
disengaging the (1) retaining clip and (1)
claw.
Plastic Nut
Retaining Clip
Claw
Page 2 of 23
2014
VEHICLE PREPARATION; continued
Tundra
5. Remove the lower steering column cover
by removing the (2) phillips screws disengaging the (2) claws.
6. Remove the driver’s instrument side panel
by disengaging the (7) claws.
7. Loosen the lower instrument panel subassembly by removing the (2) 10 mm
bolts and disengaging the (9) clips and (1)
claw.
8. Remove the hood release lever and
disengage any connectors that may be attached to the finish panel. Remove finish
panel from the vehicle.
Page 3 of 23
Vehicle Remote Start System
2014
Tundra
Vehicle Remote Start System
VEHICLE PREPARATION; continued
9. Remove the driver’s side knee air bag
assembly by removing the (4) 10 mm bolts
and disconnecting the connector.
10. Apply protective tape to the driver’s “A”
pillar, as shown. Detach the claw and
open the cover. Remove the driver’s
side “A” pillar trim panel by removing the
(1) 10 mm bolt and disengaging the (1)
claw.
Protective Tape
11. Remove the passenger’s side front door
step sill panel.
Regular Cab:
Disengage the (6) claws and (3) clips.
Double Cab:
Disengage the (6) claws and (3) clips.
Regular Cab
Double Cab
Page 4 of 23
2014
Tundra
Vehicle Remote Start System
VEHICLE PREPARATION; continued
12.Remove the passenger’s front kick panel,
by removing the (1) plastic retaining nut
and disengaging the (1) retaining clip and
(1) claw.
Retaining Clip
Claw
INSTALLATION PROCEDURES
1. Clean the area of the windshield, to the
right of the rear view mirror with a
approved VPC cleaning solution. Ensure
the glass surface is completely dry.
2. Connect the antenna harness to the
antenna. Remove the protective backing
and mount the antenna to the windshield,
to the right of the rear view mirror. Press
firmly to ensure a good glass to adhesive
bond.
Cable Ties
4. Route the antenna cable in between the
body structure and headliner, toward the
driver’s “A” pillar.
5. Route the antenna cable down the driver’s
“A” pillar to the underdash area. Secure
the antenna cable to the existing factory
harness with (3) cable ties.
Page 5 of 23
2014
Tundra
INSTALLATION PROCEDURES
6. Route the Violet, Violet/White, Green, Pink
and Yellow wires to the passenger’s side
of the vehicle.
7. Secure the remote start harness along it’s
routing path with cable ties, as needed.
8. Careful follow the wiring diagram and factory connector details found on the following (6) pages.
Page 6 of 23
Vehicle Remote Start System
2014
Tundra
Vehicle Remote Start System
WIRING DIAGRAM
Disconnect the factory female ignition switch
connector and plug the corresponding
remote start harness female connector into
the ignition switch.
Connect the factory female ignition switch
connector into the corresponding remote start
harness male connector.
GRAY / BLACK WIRE [Key-In-Sense Input]:
Use black T-Tap and connect to the GRAY
WIRE in connector J18, location 1.
BEIGE WIRE [Horn Output]:
Use black T-Tap and connect to the BEIGE
WIRE in connector J45, location 8.
PINK WIRE [ Unlock Output]:
Use black T-Tap and connect to the
WHITE WIRE in connector MJ2, location 16.
ORANGE WIRE [Parking Light Output]:
Use black T-Tap and connect to the BEIGE
WIRE in connector J10, location 18.
YELLOW WIRE [ Lock Output ]:
Use black T-Tap and connect to the RED WIRE in
connector MJ2, location 17.
VIOLET WIRE [IMI BCM Side]:
The YELLOW portion of the IMI wire in the junction
connector AJ5 (location 1) must be de-pinned, see
“Detail A” on the next page.
BROWN/WHITE WIRE [Brake Input]:
Use blue T-Tap and connect to the BEIGE
WIRE in connector A4, location 1.
WHITE WIRE [ Tachometer Input]:
Use black T-Tap and connect to the BROWN
WIRE in connector J17, location 9.
GREEN WIRE [IMO]:
Use black T-Tap and connect to the PINK WIRE in
connector AJ5, location 2.
VIOLET / WHITE WIRE [IMI Vehicle Side]:
Use black T-Tap and connect to the BLACK WIRE in connector AJ5, location 1. See “Detail A” on the next page
for additional details.
Immobilizer Interface Module
L.E.D.
Programming Button
GRAY WIRE [ Door Ajar Input ]:
Use black T-Tap and connect to the GRAY
WIRE in connector J4, location 24.
YELLOW/BLACK WIRE [ Hood Input ]:
Use red T-Tap and connect to the BLUE
WIRE in connector AJ10, location 19.
If vehicle is NOT equipped with factory
security, a hood pin switch must be installed, see Page 14 for additional details.
BLACK WIRE- (16 GA.) GROUND:
Connect to the factory 10 mm ground location in the driver’s kick panel area.
Antenna
Page 7 of 23
2014
Tundra
Vehicle Remote Start System
INSTALLATION PROCEDURES; continued
T-TAP INSTALLATION
When installing female T-Tap connectors, be sure the wire is located inside the wire channel
of the female T-Tap connector before closing the connector over the wire with pliers.
Step A
Step B
Step C
IMPORTANT! After installation, inspect and ensure that the module harnesses are clear of HOT,
SHARP or MOVING objects.
IMPORTANT! Care MUST be exercised when using the BLACK T-Taps. To avoid damage and broken wires, please note:
• Ensure there is NO tension on the T-Tap connection when securing the harness. The wire
should be slack.
• Excessive manipulation and/or stress on the wire connection could lead to wire breakage.
• Center the wire in the metal insert, NOT the plastic side of the T-Tap. Misalignment of the wire
against the metal insert could lead to cutting the wire.
• It is recommended to close close the T-Tap with your fingers (Step A above). After the T-Tap has
been closed with your fingers, applying light pressure with a set of pliers will complete the conSTOP
nection.
• When possible, install T-Taps 1” away from connector.
DETAIL A
1
1. Separate the two halves of the junction
connector.
2
2. Carefully lift up the secondary lock and
remove the YELLOW IMI wire.
3. Fold over the terminal end of the wire.
4. Protect the terminal end, by wrapping
the wire and terminal end with electrical
tape. Ensure that the terminal end is
completely covered.
3
4
5. Install T-Tap.
5
AJ5
Page 8 of 23
Note: The Yellow IMI wire may be a
different color in each side of
the junction connector.
CONNECTOR DETAILS - 2014
Tundra Vehicle Remote Start System
1. CONNECTOR J9: 12+ VDC 1 & 2 / Ignition 1 & 2 / Accessory / Starter
Location : At Ignition Switch.
Disconnect the factory female ignition switch connector
and plug the corresponding remote start harness female
connector into the ignition switch.
Connect the factory female ignition switch connector into
the corresponding remote start harness male connector.
2. CONNECTOR J10: Parking Lights / Head Lights
Location : At Head Light Dimmer Switch.
Location 18
Beige
Parking Lights
REMOTE START
Orange
J10
CAR
Beige
3. CONNECTOR J45: Horn
Location : At Spiral Cable Assembly.
Location 8
Beige
Horn
J45
REMOTE START
Beige
CAR
Beige
T-TAP COLOR
Black
Page 9 of 23
T-TAP COLOR
Black
CONNECTOR DETAILS - 2014
Tundra Vehicle Remote Start System
4. CONNECTOR J18: Key-In-Sense
Location : At Ignition Switch.
J18
Location 1
Gray
Key-In-Sense
REMOTE START
Gray/Black
CAR
Gray
T-TAP COLOR
Black
5. CONNECTOR J17: Tachometer
Location : At DLC3.
Location 9
Brown
Tachometer
J17
REMOTE START
White
CAR
Brown
T-TAP COLOR
Black
6. CONNECTOR A4: Brake
Location : At Brake Pedal Assembly.
Location 1
Beige
Brake
REMOTE START
Brown
CAR
Beige
T-TAP COLOR
Blue
A4
Page 10 of 23
CONNECTOR DETAILS - 2014
Tundra Vehicle Remote Start System
7. CONNECTOR J4: Door Ajar
Location : At body ECU, driver’s JB.
Location 24
Gray
Door Ajar
J4
REMOTE START
Gray
CAR
Gray
T-TAP COLOR
Black
8. CONNECTOR MJ2: Unlock / Lock
Location : Passenger’s kick panel.
Location 16
White
Unlock
Location 17
Red
Lock
REMOTE START
Pink
Yellow
CAR
White
Red
MJ2
9. CONNECTOR AJ10: Hood
Location : At driver’s kick panel area.
If vehicle is NOT equipped with factory security, a hood pin
switch must be installed, see Page 14 for additional details.
Location 19
Blue Wire
Hood
REMOTE START
Yellow/Black
CAR
Blue
T-TAP COLOR
Red
AJ10
Page 11 of 23
T-TAP COLOR
Black
Black
CONNECTOR DETAILS - 2014
Tundra Vehicle Remote Start System
10. CONNECTOR AJ5: IMI / IMO
Location : Passenger’s Kick Panel Area.
Location 1
Black Wire
IMI
REMOTE START
Violet
Violet/White
Green
Location 2
Pink Wire
IMO
CAR
Yellow
Black
Pink
Location 1
Yellow Wire
IMI
T-TAP COLOR
Black
Black
Black
1
1. Separate the two halves of the junction
connector.
2
2. Carefully lift up the secondary lock and
remove the YELLOW IMI wire.
3. Fold over the terminal end of the wire.
4. Protect the terminal end, by wrapping
the wire and terminal end with electrical
tape. Ensure that the terminal end is
completely covered.
3
5. Install T-Tap.
4
5
AJ5
Page 12 of 23
Note: The Yellow IMI wire may be a
different color in each side of
the junction connector.
2014 Tundra
INSTALLATION PROCEDURES; continued
9. Locate the factory ground lug in the driver’s kick panel
area. Secure the remote start harness ground wire to the
10 mm ground lug located in the driver’s kick panel area.
10.Plug the remote start wire harness into the remote start
module.
11. Plug the remote start antenna into the rear of the remote
start module.
10-Pin
Antenna
24-Pin
12.Secure the remote start module to the factory harness
connected to the driver’s JB and the metal dash assembly with (2) cable ties.
13.Secure the remote start harness to the existing vehicle
harness with cable ties, as needed.
NOTE: Ensure that the remote start harness
is secured in a manner that allows access to
the remote start harness programming button
and the immobilizer interface module
programming button.
Page 13 of 23
Vehicle Remote Start System
2014 Tundra
Vehicle Remote Start System
INSTALLATION PROCEDURES
This step is not necessary for vehicle’s
equipped with factory security.
1. Place protective tape around the radiator grille sub-assembly. Remove the (4) phillips screws and disengage
the (2) clips.
2. Disengage the (4) claws and (3) clips to remove the radiator grille sub-assembly.
3. Locate the empty hole in the passenger’s side of the upper radiator support, near the windshield wiper washer
reservoir.
Mounting Hole
Page 14 of 23
2014 Tundra
INSTALLATION PROCEDURES
4. Secure the hood switch bracket to the upper radiator
support, using (1) supplied 10 mm bolt and the (1) 10 mm
bolt.
5. Install the provided hood pin switch into the bracket. Ensure that the hood pin switch is completely seated.
6. Plug in the corresponding end of the remote start hood
switch harness into the bottom of the hood pin switch.
7. Pull back the plastic cover and route the hood pin switch
harness under the upper radiator support, to the area in
front of the radiator.
Page 15 of 23
Vehicle Remote Start System
2014 Tundra
INSTALLATION PROCEDURES
8. Secure the hood pin switch harness to the upper radiator
support and to the factory harness with (2) cable ties.
Cable Ties
9. Disengage the factory hood switch connector, located
below the hood latch assembly mounted on the radiator
core support.
10.Trim the hood pin switch harness to length.
11. Strip back approximately 1” of the protective covering
securing the (2) wires of the hood pin switch harness
together to expose the Black and Gray wires.
12. Locate the (2) provided red Scotch-Loks and remove the
metal inserts. Apply a layer of dielectric grease to each
Scotch-Lok. Reinstall the metal inserts.
13. Partially remove the protective covering on the factory
hood switch connector to expose the factory wires.
14. Using the red Scotch-Loks, connect the hood pin switch
harness wires to the factory hood pin switch connector.
15. Reinstall the factory hood pin switch connector to it’s
original mounting location.
REMOTE START
Black
Gray
CAR
Scotch-Lok COLOR
Blue
Red
White/Black
Red
Page 16 of 23
Vehicle Remote Start System
2014 Tundra
Vehicle Remote Start System
VEHICLE RE-ASSEMBLY
1. Refer again to the vehicle repair manual and reinstall the driver’s knee air bag assembly.
S
Driver’s knee air bag assembly bolts must be
torqued to 10 Nm (7 ft.-lbf).
2. Clean the area of the radiator grill sub-assembly, in
front of the hood latch assembly (indicated by the
orange box below) with a approved VPC cleaning
solution. Ensure the surface is completely dry.
3. Remove the protective backing from the Under
Hood Warning Label and place onto the
radiator grill sub-assembly.
4. Re-connect the negative battery cable. Torque to
48 in. lbs.
5. Attach the Remote Start Transmitter and Key
Tag to the factory ignition key.
6. Place the Remote Start Owner’s Guide in the
glove box.
Page 17 of 23
Negative Battery
Cable
2014 Tundra
Vehicle Remote Start System
PROGRAMMING IMMOBILIZER & HOOD STATUS SIGNALS
STOP Read through the entire procedure before proceeding!
Note: Programming procedure must be completed within 60 seconds.
1.
2.
Verify that the hood is closed and the ignition is off.
Press and hold the brake pedal and the programming button of the remote start harness for
10 seconds. The LED of the remote start harness will turn ON.
3. Verify that the immobilizer interface module LED is blinking Red - Green.
4. Press and release programming button, located on the side of the immobilizer interface module.
5. Verify that the immobilizer interface module LED is blinking Red.
6. Open the vehicle’s hood.
7. Verify that the immobilizer interface module LED is on solid Red.
8. Close the hood.
9. Press and release programming button, located on the side of the immobilizer interface module.
10. Verify that the immobilizer interface module LED is on solid Green for (2) seconds and then turns to
solid RED.
Note: Vehicle’s NOT equipped with Immobilizer stop here, programming is complete. Vehicle’s
equipped with Immobilizer, proceed to Step 11.
11. Start the vehicle.
12. Verify that the LED on the side of the immobilizer interface module turns solid Green for (2) seconds
and then turns off.
13. Let vehicle run for at least 5 seconds.
14. Programming complete! Turn vehicle off.
15. Reassemble any removed vehicle interior components, making sure to plug in any connectors that
were disconnected during vehicle disassembly.
If the Immobilizer Interface Module fails to program, or programs incorrectly, check the following:
1. Repeat Steps 1 - 14 and verify that the programming procedure was completed within the 60 second time
limit.
2. Verify that the correct remote start harness wires were connected to the correct vehicle wires and are
secure, per the installation manual.
3. Perform reset procedure, located on Page 20 and then repeat Steps 1 - 14 above.
Immobilizer Interface Module
Programming Button
LED
Page 18 of 23
2014 Tundra
IMMOBILIZER INTERFACE MODULE RESET PROCEDURE
Vehicle Remote Start System
STOP Read through the entire procedure before attempting to reset the immobilizer interface module.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Verify that the hood is closed and the ignition is off.
Disconnect all connectors from the from the immobilizer interface module.
Press and hold the brake pedal and the programming button of the remote start harness for
10 seconds. The LED of the remote start harness will turn ON.
Press and Hold the programming button while connecting the 4 pin connector containing the Red,
Black and Blue wires.
The LED will turn ON RED for 1 second and then turn OFF.
In 3 seconds the LED will begin to flash RED. Immediately release the programming button.
The LED will begin turn ON RED for 1 second and then begin flashing a GREEN - RED pattern.
Reset Complete.
Turn the vehicle’s ignition key to the OFF position.
Reconnect all connectors.
WARNING! Continuing to hold the programming button after the immobilizer interface module begins to
flash GREEN - RED (Step 6) will erase the base software, making the module unusable.
Immobilizer Interface Module
Programming Button
LED
Page 19 of 23
PROGRAMMING TACHOMETER SIGNAL
STOP
2014 Tundra
Vehicle Remote Start System
Vehicle MUST be at normal operating temperature before programming the tachometer signal.
Failure to ensure that the vehicle is at normal operating temperature may result in a no-start
condition and may cause customer dissatisfaction and/or warranty returns.
1.
2.
3.
4.
Turn the vehicle’s ignition to the “On” position.
Press and hold the brake pedal.
Locate the programming button, attached to the remote start harness.
Press and hold the programming button for 10 - 15 seconds.
The horn will beep and the lights will flash (3) times.
5. Release the programming button and brake pedal.
6. Press and release the programming button.
The horn will beep and the lights will flash (4) times.
7. Press and hold the brake pedal.
The horn will beep and the lights
will flash (1) time, signifying that the remote start is now in “Tachometer Learn Mode”.
8. Start the vehicle. The remote start will flash the parking lights every (3) seconds.
9. Once the vehicle has come to a normal idle (approximately 15 seconds), press and release remote
start harness programming button.
The horn will beep and the lights will flash (5) times, signifying that the tachometer signal is
now “locked in”.
10.Turn vehicle off.
TESTING THE REMOTE START SYSTEM
Press 2 times within 3 seconds to
activate the Remote Start function.
Press and hold for 10 seconds to
activate the Remote Stop function.
Press for Progressive CarFind ®
x1= 5 Soft Chirps
x2= 5 Louder Chirps
x3= 5 Full Volume Chirps
Green L.E.D. flash with every
button press to confirm proper
operation and a good battery.
During Remote Start operation, press
1 time to unlock the doors.
Press and Hold for Personal
Protection Alarm.
FUNCTION TEST
A. HOOD AJAR STATUS:
1. Make sure all the doors are closed but hood is open and windows are down.
2. Activate the remote start function by pressing the
button 2 times within 3 seconds on the 2-way
remote control transmitter. The transmitter should beep and flash the led one time.
3. The remote start system should turn the ignition on, but then honk the horn twice and shut down,
indicating that the hood is open. The transmitter should beep and flash the led two times.
4. Close the hood.
B. KEY-IN-SENSE:
1. Enter the vehicle and close the door. Insert a key into the ignition switch.
2. Activate the remote start function by pressing the
button 2 times within 3 seconds on the 2-way
remote control transmitter. The transmitter should beep and flash the led one time.
3. The remote start system should turn the ignition on, but then honk the horn two times and shut down,
indicating that a key is in the ignition.
4. Remove the key from the ignition.
Page 20 of 23
2014 Tundra
Vehicle Remote Start System
TESTING THE REMOTE START SYSTEM
FUNCTION TEST; continued
C. BRAKE INPUT:
1. Press the brake pedal.
button 2 times within 3 seconds on the 2-way
2. Activate the remote start function by pressing the
remote control transmitter. The transmitter should beep and flash the led one time.
3. The remote start system should turn the ignition on and lock the doors, but then honk the horn two times
and shut down, indicating that the brake pedal is pressed.
4. Release the brake pedal.
D. DOOR STATUS:
1. Open the driver’s door.
2. Activate the remote start function by pressing the
button 2 times within 3 seconds on the 2-way
remote control transmitter. The transmitter should beep and flash the led one time.
3. The remote start system should turn the ignition on and lock the doors, but then honk the horn three times
and shut down, indicating that a door is open while attempting to remote start the vehicle.
4. Close the vehicle door.
E. CAR FIND/PANIC:
1. Press the
button (1) times on the 2-way remote control transmitter. The horn should honk (5) times
and the parking lights should flash (5) times.
Repeat this process twice. Subsequent presses within 5 seconds of the first press will honk the
horn slightly louder.
button on the 2-way remote control transmitter for 3 seconds. The horn should
2. Press and hold the
start honking and the lights will flash in a random pattern (Real Panic Sound). The Panic feature can be
stopped by pressing the
button a second time.
F. REMOTE START OPERATION:
1. Close the driver’s door.
2. Activate the remote start function by pressing the
button 2 times within 3 seconds on the 2-way remote control transmitter. The transmitter should beep and flash the led one time.
3. Once the vehicle starts, the transmitter should beep (2) times and flash the led (2) times and then flash
every few seconds, signifying that the vehicle is still running. Verify that all heat and A/C functions operate
normally and that the doors have locked.
4. Once all systems have been checked, pressing the
button on the 2-way remote control transmitter,
the transmitter should beep (2) times and flash the led (2) times and the doors should unlock.
5. Verify that the vehicle runs for (15) minutes and then shuts down. The doors should lock and the transmitter should beeps (3) times and flash the led (3) times.
Function Test Complete!
Page 21 of 23
VEHICLE FUNCTION CHECKLIST
(These points must be checked to ensure a quality installation)
Headlight
If the warning lights remains on, it may indicate
a system malfunction.
Massage Seats (if equipped)
High Beams
Side Mirror Defogger (if equipped)
Turn Signal Lights
Front Windshield Defogger (if equipped)
Tail Lights
Navigation System (if equipped)
Stop Lights
Rear Sunshade (if equipped)
Backup Lights
Cruise Control Light (if equipped)
Hazard Lights
Steering Wheel Audio Control (if equipped)
Marker Lights
HVAC
Dome/Courtesy Lights
Power Locks (if equipped)
Panel/Switch Illumination
Power Windows (if equipped)
Accessory Controls/Illumination
(If equipped)
Gauges
Power Side Mirrors (if equipped)
Front Wiper/washer
Rear Window Defogger (If equipped)
Hood Latch Release
Key Sensor Buzzer
Passenger Air Bag Switch (if equipped)
Fog Lights (If equipped)
Rollover Side Curtain Air Bag Switch (RSCA)
Day Time Running Lights
(If equipped)
Horn
Seat Belt Warning Light
If the warning lights remains on, it may indicate
a system malfunction.
Trunk/Tailgate/Bed Lights
(If equipped)
Glove Box Light (If equipped)
Air Bag Warning Light
If the warning lights remains on, it may indicate
a system malfunction.
ABS Light (If equipped)
Rear Wiper/Washer (If equipped)
Lamp Failure Sensor
If the warning lights remains on, it may indicate
a system malfunction.
Clock (If equipped)
Accessory Power Socket (If equipped)
Track/Skid Control Light (if equipped)
If the warning lights remains on, it may indicate
a system malfunction.
Starter
Audio/Video (If equipped)
Power Rear Door (If equipped)
Convenience Memory Settings (If equipped)
Heated Seats (If equipped)
Page 22 of 23
Tire Pressure Monitoring System (TPMS)
Prior to TPMS activation and Pre-Delivery
Service (PDS) of the vehicle the TPMS light will
blink when IG is turned on.
2014 Tundra
TROUBLE SHOOTING
Horn Honks
Safety Feature
2
Hood opened, Brake Pedal pressed or Key in the ignition
3
Door is open before remote start.
4
No tachometer programmed / No tachometer signal present.
6
Valet/Service Mode engaged
SYMPTOM
•
Vehicle Remote Start System
SOLUTION
System does not respond to transmitter
•
•
Verify that the antenna is plugged into the back of the
remote start module.
Verify proper battery voltage in transmitter (3 volts).
•
Poor operating range
•
•
Verify antenna is mounted in the correct location.
Verify that the antenna is plugged into the back of the
remote start module.
•
Vehicle will not unlock using the transmitter.
•
Verify that the correct vehicle wire was connected to the
proper remote start harness wire (Page 11, step 8).
•
Vehicle does not lock with remote start request.
•
Verify that the correct vehicle wire was connected to the
proper remote start harness wire (Page 11, step 8).
•
Parking lights do not flash.
•
Verify that the correct vehicle wire was connected to the
correct remote start harness wire (Page 9, step 2).
Verify that the fuse located under the DNA case top labeled
“PK LIGHTS” is good and installed in the negative position
per the Fuse and Jumper Reference Drawing.
Verify proper DNA installation.
•
•
•
Vehicle’s horn does not honk when activating the Car Find
or Panic features.
•
Verify that the correct vehicle wire was connected to the
correct remote start harness wire (Page 9, step 3).
•
Ignition turns on, horn honks 2 times and the vehicle does
not start. Key-In-Sense activated.
•
•
Remove the ignition key from the ignition cylinder.
Verify that the correct vehicle wire was connected to the
proper remote start harness wire (Page 10, step 4).
•
Vehicle remote starts, but does not stay running.
•
Verify that the IMO/IMI wires are properly connected and
secure (Page 12, step 10).
Verify that the correct vehicle wire was connected to the
correct remote start harness wire (Page 10, step 5).
Reprogram the vehicle’s tachometer signal.
•
•
While the vehicle is running during the remote start mode,
the air conditioning/heater does not operate.
•
•
•
Verify that the 8-pin male and female ignition switch connectors are connected properly and secure (Page 9 , step
1).
Verify that the fuse located under the DNA case top labeled
“HVAC1” and “HVAC2” are good and installed in the positive position per the Fuse and Jumper Reference Drawing.
Verify proper DNA installation.
Accessing the DNA Card
Fuse and Jumper Reference Drawing
DOME LIGHT
+
2
-
1
2
DOOR LOCKS
+
DR DOOR/TRNK REL
PK LIGHTS
-
•
1
HVAC 1
*Verify that both rows of multi-pin connectors are aligned and seated properly.
HVAC 2
Page 23 of 23
MAIN B+
IGN