Remote Power Supply System
210W charging specification
Wireless charging achieve
labor savings!
<Image of AGV>
Head
Charging unit
Now charging
wirelessly!
It connects with
24V lead battery
Power Supply
unit
(AGV body, I had offers from SHOWA AIRCRAFT INDUSTRY CO.,LTD.)
Benefits of system introduction
● Battery replacement connectors and
connection for charging is not required, I was
able to achieve power saving!
● Allows 24 hours of continuous operation with
automatic charge!
● No risk of electric shock, safe and secure
● To the charge in stop place AGV, prevents, or
low battery, the charging forgetting.
● The status signal of the voltage monitor, etc.,
and improved operability
Passive Head
RCS240PH
Charging unit
RCS210-PB24
<Charging side>
Active Head
RCS240AH
Power Supply unit
RCS240-AC1
<Power supply side>
The battery charge image in AGV
Lead battery loading
Wireless charging
&Status signal transmission
<Charge
Termination>
AGV
Fixed
side
(Active)
Movable
side
(Passive)
Remote Power Supply System
System chart
Wireless charging Remote System
Wireless Charging
24V lead
battery
External
control
devices
Power
Active Head
Passive Head
Power
Temperature
detection
AC Power
External
control
devices
Thermistor
Signal
Signal
Power Supply unit
Charging unit
＜Charging side＞
Signal
＜Power Supply side＞
And benefits
Transmitting a signal to an external
device in the communication function
Improvement of
existing lines
and smooth easy
installation work
Battery life up at
a constant current and constant
voltage
Reliable error detection, the protection function
+
-
Charging characteristics (Reference)
30Ah (5 hour rate)　Battery discharge about 50%
CC · CV charging
characteristics
CC-CV充電特性
32
8
30
24VDC/300mA
28
非接触給電
7
6
voltage
電圧
Charging voltage
充
(V)
26
電
24
4
22
3
20
2
18
1
16
0
リモート部
ベース部5
current
電流
電
（
圧
24VDC/2A
100Hz
）
V
Charging current
(A)
充
電
電
流
電源
検出信号
制御信号
0
25
50
＜可動側＞
75
100
40Hz
125
150
175
200
225
時間（分）
Time (minutes)
＜固定側＞
The control of charging is the CC,CV(*1) . When voltage of Battery became to the fixed voltage and the discharge current of
it dropped until 1.5A, it will go a state of intermittent charging. Also, when the passive head went out of range that active
head can supply power, it will stop supply power automatically and go standby state.In the case of the state of intermittent
charge. When the ouput current became to 3 A, it will return to the CV charge and it does the above.
*1. At the first, it will charge with constant current. After it became to the constant voltage.
It is the method to charge while lowering the current to maintain the voltage.
Remote Power Supply System
Specification
Charging unit
Power Supply unit
230
7
18
15
6.5
194
B View
90
15
8-7X15
B View
210
190
170
188
300
90
A View
175.7
A View
90
160
80
50.5
2
A View
A View
B View
B View
1
Type code
RCS210-PB24
Type code
RCS240-AC1
Output voltage
≦ 30V (It varies depending on battery temperature)
Output current
Input
≦ 7A (It varies depending on battery voltage)
Voltage monitor request
Voltage monitor signal, charging signal,
intermittent charging signal,Battery error signal
Natural air cooling
Input : Overvoltage protection
Battery : High temperature / low temperature protection, not connected, reverse connection protection
Power supply voltage
Current consumption
Input
Cooling method
LED display
100V AC / 200V AC
4A
Start-up signal
Voltage monitor signal, Inzone signal,
charging signal,
Intermittent charging signal, Battery error signal
Forced air cooling
Status display of input and output signal
Operating temperature
Protection class
Active
Connection Communication
Power
Material　Main part case
Weight
0...+50℃
IP20
Round 3-pin connector
D-Sub 9-pin connector
3P inlet
SECC
2.6Kg
Accessories
Power cable (2m), External device communication connector,4 screws M6x15
Cooling method
Protection circuit
Operating temperature
Protection class
Active
Communication
Connection
Terminal block
0...+40℃
IP20
Round 3-pin connector
Round 5-pin connector
Battery connection (2-pole),Thermistor connection (2-pole),
Terminal width 6.2mm or less, Terminal screw size M3
Material
Weight
Main part case Aluminum
1.6Kg
Output cable (1.5m), Thermistor with cable (1.5m),
External device communication connector, 4 screws
Accessories
M6x15
Passive Head
140
Active Head
4- φ 6.5
100
100
86
140
126
Output
126
4- φ 6.5
86
Output
(1000)
40
40
8
8
(1000)
Type code
RCS240PH
Output voltage
Output current
Transmission distance
Permissible center off-set
Output current
Charging unit reference
Operating voltage
Charging unit reference
Current consumption
0...10mm
Load current
≦ 10mm（The sum of X and Y are less than 10mm） Frequency response
Charging unit reference
LED display
Operating temperature 0...+50℃
Protection class
IP65
Active：Round 3-pin, Signal：Round 5-pin
Connection
Each connector cable included (1m)
Material Active surface PPS
Back
Aluminum
Weight
1.2Kg
Accessories
4 screws M6x15
Type code
Operating temperature
Protection class
RCS240AH
Power Supply unit reference
Power Supply unit reference
-------
0...+50℃
IP65
Active：Round 3-pin, Signal：D-sub 9-pin
Connection
Each connector cable included (1m)
Material Active surface PPS
Back
Aluminum
Weight
1.2Kg
Accessories
4 screws M6x15
Remote Power Supply System
Installation Notices
Installation
Wiring
Output cable
In order to obtain a good cooling effect, please keep spaces between the surrounding and the body unit as shown
as below, so as not to block the airflow.
More than5ｃｍ以上
5cm
(1)24V lead battery
(2)Thermistor with Cable
10ｃｍ以上
More than 10cm
Charging unit
Power Supply unit
More
than 5cm
5ｃｍ以上
5ｃｍ以上
More
than 5cm
Mutual interference
If you are installing in parallel head, to avoid the effects
of mutual interference, please attach the head with an
interval greater than or equal to the value shown in the
table below always.
(1)　External device
communication cable
(AWG24 ～ 16)
※ Single phase 100V,200V
To the power supply side
A
Power cable
※
Passive Head
B
Type code A(mm)
RCS240AH
300
RCS240PH
B
Attachment
Please make the following is greater than or equal to
the number of R(mm) bending of the cable line.
・Active Cable line and Passive Cable line : R50
・Signal Cable line : R30
R
Surrounding metal
Metal
A
C
Metal
B
To avoid influence of surrounding metal,
keep minimum spacing.Remove metal chips
or metallic debris on the active surface.Metal
chips or metallic debris generate may damage to device or cause unexpected trouble.
Type code
RCS240AH
RCS240PH
(1)　External device
communication
cable
(AWG28 ～ 16)
Active Head
(1)Parts of the dotted line (External device communication cable and
24V lead batteries) within the product is not included with this
product.They are contents prepared and processed of a visitor.
(2)That the protection function is turned ON, will be more than 40.5 ℃ .
(Due to the installation conditions, there is a difference about ± 2 ℃ .)
Please use the attached article always thermistor. Please be
attached to the upper surface of the terminal near the 24V lead
batteries. In that case, please do not touch any terminals.
(3)Each cable, please connect with the specified length. You may receive
an error due to the output such as a decrease occurs.
Center off-set and transmitting distance
The permissible center off-set of the feed head and charging
head, please be installed so that the total (X + Y) axis deviation of the width of the X-axis · Y-axis is the following table.
G
X-axis direction
Y-axis
direction
Direction Distance
G
≦ 10mm
X+Y
A(mm) B(mm) C(mm)
100
40
45
Request for use on
軸ズレ　XまたはYどちらか１方向　(mm)
● This product, which is one of those high frequency utilization equipment of Radio Law, Upon use You will need to install
application. Please use it after you have made the application without fail.
Installation details of the application procedure, see Telecommunications website of the Ministry of Internal Affairs and
Communications, Please.
● The control communication device that is installed in the product, there is no need for (diploma) radio station authorization of
the Minister so apply to "a weak radio station (weak radio equipment)" to.
However, please be careful on the occasion of the operation because it may affect medical equipment and electronic
equipment (such as pacemakers).
● This product has become a Japan national specification. It can not be used outside of Japan. When used outside of Japan,
I guess we assume any liability You.
● When using, refer to instruction manual, user's guide always.
Wireless Power Supply by
Mail：b-plus-usa@b-plus-kk.com
Web：http://www.b-plus-kk.com
* Contents is subject to change without notice.
BN1301Fe
2016.02