ESS48 Type 2 - Century Yuasa

advertisement
Enersun ESS48
Type 2 Off-grid power system
Enersun ESS48 is a range of off-grid power systems designed for 48VDC continuous
load applications. The array is sized to provide adequate power to recover a battery
after no sun for periods of 3-days, 5-days or 7-days for varying sun-hours.
Supplied standard with each system is array frame, battery and power cabinets.
The array frame is manufactured locally from steel, each member being double
hot dipped galvanised and the cabinets are zinc primed and powder coat finished.
To guarantee the back-up capability of the system Yuasa VRLA AGM batteries are
specified which can provide 8-years service life.
The photovoltaic modules use utilise monocrystalline technology, and are certified
to international standard IEC 61215 ed.2. Using high quality material, these
modules are guaranteed against material and workmanship defects for 10-years,
with 25-year pro rata warranty on performance*. Control of charging is managed
by Pulse Width Modulation regulator which are natural convection cooled. These
have a two (2) voltage free contacts to generate alarms.
EN309-1218
Best of all selection is simple. By using the supplied matrix and referencing the
corresponding continuous load requirement with the sun-hours and days back-up
required, it is possible to quickly select the most appropriate Enersun ESS48 system
for your application.
ESS48 Type 2
Sun Hours
5.5 4.5 3.5
Days Back-up
Load (W)
3
100
150
D
200
5
7
3
B
E
D
5
7
B
E
3
5
7
A
B
C
Enersun ESS48
Type 2 Off-grid power system
Photovoltaic Structure Solar Regulator
Type
Enersun 1612
Type
Pulse Width Modulation
Mounting
Ground Mount
Number of Regulators
1
No. of Array Structures
1
Max. Charging Current (A)
40
Region Suitability**
Region B
Max. Load Current (A)
7
Material
Hot Dipped Galvanised Steel
Alarms
Qty 2 voltage free contacts
Moniotring & Remote Communication
RS232 Computer Interface which uses propriety software that is compatible w ith Win 95/98/NT.
NOTE:*Maximum allowable wind speeds are based on AS/NZS 1170. Conditions apply in relation
to the effects of terrain categories and topographic multipliers. These effects can affect the
suitability of the design to meet the relevant standards. Each site should be assessed by a suitably
qualified person prior to specification or suitability of these products.
Photovoltaic Modules
Electrical Output Specification
Type
MonoCrystalline
Nominal VDC
48VDC
Rated Power (W)*
95W
VDC Operating Range
43VDC - 58VDC
No. Modules
16
Load Type
Continuous
Arrangement
4-Strings of 4 Modules in Series
Duty Cycle
24-hours (100% Duty Cycle)
Power (W)
Refer to Table
PV Array Dimensions
o
NOTE: *Maximum power at STC (1000W/m2 @ 25 C 1.5AM)
Electrical
Environmental
PV Output Isolation
15kA C60N MCB
Rated Temperature
Battery Breaker
MCB C120N
Operating Temperature Range
Distribution
Qty 6 x 1P C60 MCB
Lightning Protection
25kA per Regulator
Battery
A
25oC
0 oC - 45oC
o
NOTE: ^Capacity of Battery will reduce below 25 C, and above 25oC service life reduces.
B
C
D
Type
Yuasa UXL Solar
Technology
VRLA AGM
Number of cells
24
Installed Capacity (Ah @ C100)
240
24
360
24
480
Max. DoD%
24
24
80%
Service Life 8-years (to 80% of Rated Capacity)*
Battery Enclosure Type
Outdoor Cabinet with heat sheilds
Material
600
E
Welded steel cabinet, galvinised undercoat with powdercoat finish
Design Considerations
AS/NZS 1170.1-2002: Structural design actions - General
AS/NZS 1170.1-2002 Part 1: Structural design actions - Permanent, imposed and other actions
AS.NZS 1170.2-2002 Part 2: Structural design actions - Wind actions
AS/NZS 1768-2007: Lightning Protection
AS/NZS 3000-2007: Australian/New Zealand Wiring Rules
AS/NZS 3015-2004: Electrical installations - Extra-low voltage DC. Power supplies and service earthing within public telecommunications networks
AS 4086.1-1993: Secondary batteries for use with stand-alone power systems - General requirements
AS 4086.2-1997 -Secondary batteries for use with stand-alone power systems - Installation and maintenance
AS 4509.1-2009: Stand-alone power systems Part 1: Safety and installation
AS 4509.2-2009: Stand-alone power systems - System design
AS/NZS 5033-2005: Installation of photovoltaic (PV) arrays
EN309-1218
IEC61215 Ed 2: Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval
For further information please refer to CenturyYuasa website www.enersun.com.au,
or contact; Australia 1300 364 877 New Zealand 0800 236 8876
All reasonable care has been taken to ensure that the data presented in this document is accurate at the time of printing and for the
purpose for which it is presented. Century Yuasa reserves the right to make changes to its products and information contained in this
document without notice, and shall not be held liable for any loss or damage claimed to have arisen as a result of the use of this sales
720
Download