Installation Guide
GE
Lighting Solutions
GE LED Luminaire Mounting Methods
Overview
Step 1: Choose Ceiling Mounting Method options:
• Option A: Onto outlet box with Non-feed Canopy Plate Kit (60658)
• Option B: Suspend from structure with Suspension Mounting Bracket Kit (69076) or Suspension Fixed Toggle Kit (69075)
• Option C: Onto unistrut with Mounting Bracket Kit (69078)
Step 2: Choose Luminaire Mounting Method options:
• Suspension Fixed Toggle Kit (69075)
• Mounting Bracket Kit (69078)
Step 3: Level Luminaire
Step 1: Choose Ceiling Mounting Method
OPTION A Onto outlet box with Non-feed Canopy Plate Kit (60658)
Equipment Required:
• 1 Non-feed Canopy Plate Kit spaced every 4 ft. max.
Kit includes: two non-feed canopy plates, two crossbars, two 1-inch studs, four 8-32(M4) screws
• Outlet box (provided by others)
• Philips screwdriver
Crossbar
Step 1
imagination at work
Directions:
Step 1
Attach crossbar to outlet box in ceiling with two 8-32 (M4)
screws. Repeat on other side.
Step 2
Fit canopy over stud of crossbar then screw cable coupler
onto stud.
Stud of crossbar
Canopy
Cable coupler
Part of 69076, 69075 kits
Suspension cable
Step 2
OPTION B Suspend from structure with Suspension Mounting Bracket Kit (69076)
or Suspension Fixed Toggle Kit (69075)
Equipment Required:
• 1 hourglass sleeve/4 ft. (supplied in kits 69076 or 69075)
• Mounting structure (provided by others)
Hourglass sleeve
Directions:
Feed cable through bottom of hourglass sleeve as shown.
Pass cable around mounting structure (i.e. strut, pipe, purlin,
eyebolt etc.) and back into top of sleeve. Provide sleeve
spaced every 4 ft. max.
Mounting structure
provided by others
OPTION C Onto unistrut with Mounting Bracket Kit (69078)
Equipment Required:
• Unistrut (provided by others)
• 2 Unistrut threaded posts/4 ft. (provided by others)
Directions:
Fasten threaded posts to unistrut for each luminaire spaced
every 4 ft. max.
Unistrut provided
by others
Threaded post
provided by others
Step 2: Choose Luminaire Mounting Method
OPTION A Suspension Fixed Toggle Kit (69075)
Equipment Required:
• 1 Suspension Fixed Toggle Kit spaced every 4 ft. max.
Kit includes: one cable coupler, one 60” down cable, one 12” toggle cable, one cross cable gripper,
one screw, one hourglass sleeve
Down cable
Cross cable gripper
Toggle cable
Directions:
Step 1
Remove toggle cable from bag and inspect for damage.
If cable appears frayed do not use.
Remove screw from cross cable gripper and insert toggle
cable into slot. Replace screw and tighten.
Step 1
Step 2
Insert both ends of the toggle cable into the luminaire
mounting holes and adjust so that the toggles are engaged
and will not come out of the holes when loaded.
Insert toggles into holes
Step 2
OPTION B Mounting Bracket Kit (69078)
Mounting
bracket
4” shoulder-bolt
Bracket slots
Equipment Required:
• 1 Mounting bracket spaced every 4 ft. max. which includes:
one mounting bracket, one 4” 1/4-20 shoulder bolt,
one washer, one nut
• 7/16th wrench
Directions:
Insert mounting bracket tabs into the slots on both sides
of the luminaire. Install 4” 1/4-20 shoulder-bolt through the
center of the bracket and tighten nut with 7/16th wrench.
Install a second mounting bracket on the opposite end of the
fixture.
Fasten both mounting brackets to Unistrut threaded posts
using appropriate nuts and washers..
OPTION C Suspension Mounting Bracket Kit (69076) + Mounting Bracket Kit (69078)
Cable gripper
Mounting
bracket
Equipment Required:
• 1 Suspension Mounting Bracket Kit spaced every 4 ft. max.
Kit includes: one cable coupler, one 60” down cable,
one cable gripper, one screw, one hourglass sleeve
• 1 Mounting bracket needed/4 ft. max. which includes:
one mounting bracket, one 4” 1/4-20 shoulder bolt,
one washer, one nut
• 7/16th wrench
Directions:
Fasten cable coupler to Unistrut bracket through mounting
slot by using 1/4-20 screw. Insert mounting bracket tabs
into the slots on both sides of the luminaire. Install 4” 1/4-20
shoulder-bolt through the center of the bracket and tighten
nut with 7/16th wrench. Feed suspension cable through cable
coupler.
1/4-20 screw
Install a second mounting bracket and cable coupler on the
opposite end of the fixture.
Step 3: Level Luminaire
Squeeze tip to adjust
Directions:
To adjust height and to level a fixture, squeeze the tip of
the gripper down and pull the suspension cable to the
desired height. Clip the cable with cable cutters to finish the
appearance.
NOTE: Gripper cannot be depressed while there is weight on
mechanisms.
Conforms to the following standards:
GE Lighting Solutions • 1-888-MY-GE-LED • www.gelightingsolutions.com
1-888- 69- 43-533
GE Lighting Solutions, LLC is a subsidiary of the General Electric Company. The GE brand and logo are trademarks of the General Electric Company.
© 2012 GE Lighting Solutions, LLC. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions.
IND048-121312