Not for New Design
TSOP362..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Continuous data transmission possible
1
2
3
• TTL and CMOS compatibility
4
• Output active low
• Low power consumption
16797
• High immunity against ambient light
MECHANICAL DATA
• Supply voltage: 2.7 V to 5.5 V
Pinning
1 = GND, 2 = GND, 3 = VS, 4 = OUT
• Compliant to RoHS Directive 2011/65/EU and in
accordance to WEEE 2002/96/EC
DESCRIPTION
SPECIAL FEATURES
The TSOP362.. series are miniaturized SMD-IR receiver
modules for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
• Improved immunity against ambient light
• Suitable burst length  10 cycles/burst
• Taping available for topview and sideview assembly
The demodulated output signal can directly be decoded by
a microprocessor. TSOP362.. is the standard IR remote
control SMD-receiver series, for 3 V supply voltage
supporting all major transmission codes.
This component has not been qualified according to
automotive specifications.
PARTS TABLE
CARRIER FREQUENCY
STANDARD APPLICATIONS (AGC2/AGC8)
36 kHz
TSOP36236
38 kHz
TSOP36238
40 kHz
TSOP36240
56 kHz
TSOP36256
BLOCK DIAGRAM
APPLICATION CIRCUIT
17170
30 kΩ
Transmitter
with
TSALxxxx
VS
4
Input
AGC
Band
pass
Demo dulator
OUT
R 1 = 100 Ω
TSOPxxxx
VS
Circuit
3
µC
OUT
GND
+ VS
C1 =
4.7 µF
VO
GND
1; 2
PIN
Control circuit
R1 and C1 recommended to suppress power supply
disturbances. The output voltage should not be
hold continuously at a voltage below VO = 2.0 V
by the external circuit.
GND
16839
Rev. 2.3, 21-Feb-12
1
Document Number: 82187
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Design
TSOP362..
www.vishay.com
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
Supply voltage (pin 3)
SYMBOL
VALUE
UNIT
VS
- 0.3 to + 6
V
mA
Supply current (pin 3)
IS
3
Output voltage (pin 4)
VO
- 0.3 to (VS + 0.3)
V
Output current (pin 4)
IO
10
mA
°C
Tj
100
Storage temperature range
Junction temperature
Tstg
- 40 to + 100
°C
Operating temperature range
Tamb
- 25 to + 85
°C
Ptot
30
mW
Tamb  85 °C
Power consumption
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
Supply current
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
Ev = 0
ISD
0.7
1.2
1.5
Ev = 40 klx, sunlight
ISH
Supply voltage
1.3
VS
Ev = 0, test signal see fig. 1, IR diode TSAL6200,
IF = 250 mA
Transmission distance
IOSL = 0.5 mA, Ee = 0.7
test signal see fig. 1
mA
mA
5.5
d
mW/m2,
Output voltage low
2.7
UNIT
V
35
m
VOSL
250
mV
Minimum irradiance
(30 kHz to 40 kHz)
VS = 3 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1
Ee min.
0.35
0.5
W/m2
Minimum irradiance
(56 kHz)
VS = 3 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1
Ee min.
0.4
0.6
W/m2
Minimum irradiance
(30 kHz to 40 kHz)
VS = 5 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1
Ee min.
0.45
0.6
W/m2
Minimum irradiance
(56 kHz)
VS = 5 V, pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 1
Ee min.
0.5
0.7
W/m2
Maximum irradiance
tpi - 5/fo < tpo < tpi + 6/fo, test signal see fig. 3
Ee max.
Angle of half transmission distance
1/2
Directivity
W/m2
30
± 45
deg
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Ee
Optical Test Signal
1.0
(IR diode TSAL6200, IF = 0.4 A, 30 pulses, f = f0, t = 10 ms)
Output Pulse
t po - Output Pulse Width (ms)
0.9
t
tpi *
* tpi
VO
T
10/f0 is recommended for optimal function
Output Signal
1)
2)
VOH
VOL
td 1)
16110
7/f0 < td < 15/f0
tpi - 5/f0 < tpo < tpi + 6/f 0
tpo 2)
0.8
0.6
0.5
0.4
0.3
0.2
= 950 nm,
optical test signal, fig. 1
0.1
0.0
t
0.1
16908
Fig. 1 - Output Function
Rev. 2.3, 21-Feb-12
Input Burst Duration
0.7
1
10
100
1000
10 000
Ee - Irradiance (mW/m²)
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
2
Document Number: 82187
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Design
TSOP362..
www.vishay.com
Optical Test Signal
600 µs
t
600 µs
t = 60 ms
94 8134
Output Signal, (see fig. 4)
VO
VOH
VOL
4.0
Ee min. - Threshold Irradiance (mW/m2)
Ee
Vishay Semiconductors
Correlation with ambient light sources:
10 W/m2 1.4 klx (Std.illum.A, T= 2855 K)
10 W/m2 8.2 klx (Daylight, T = 5900 K)
3.5
3.0
2.5
2.0
1.5
Ambient,
0.5
0.0
0.01
t
t off
t on
Ton
0.7
0.6
0.5
Toff
0.3
= 950 nm,
optical test signal, fig. 3
0.1
0.0
0.1
1
10
100
1000
Ee min. - Threshold Irradiance (mW/m²)
E e min./Ee - Rel. Responsivity
0.8
0.6
0.4
f = f0 ± 5 %
Δ f(3 dB) = f0/10
0.0
16925
1.1
f = 1 kHz
0.5
f = 100 Hz
0.0
1
10
100
1000
VsRMS - AC Voltage on DC Supply Voltage (mV)
2.0
f(E) = f0
1.6
1.2
0.8
0.4
0.0
0.0
1.3
f/f0 - Relative Frequency
94 8147
Fig. 5 - Frequency Dependence of Responsivity
Rev. 2.3, 21-Feb-12
1.0
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
1.0
0.9
f = 10 kHz
0.1
1.2
0.7
f = fo
16912
Fig. 4 - Output Pulse Diagram
0.2
100
1.5
10 000
Ee - Irradiance (mW/m²)
16909
10
2.0
Ee min. - Threshold Irradiance (mW/m²)
Ton ,Toff - Output Pulse Width (ms)
0.9
0.2
1
Fig. 6 - Sensitivity in Bright Ambient
1.0
0.4
0.1
E - Ambient DC Irradiance (W/m 2)
16911
Fig. 3 - Output Function
0.8
= 950 nm
1.0
0.4
0.8
1.2
1.6
2.0
E - Field Strength of Disturbance (kV/m)
Fig. 8 - Sensitivity vs. Electric Field Disturbances
3
Document Number: 82187
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Design
TSOP362..
www.vishay.com
Vishay Semiconductors
0°
10°
20°
30°
0.8
Max. Envelope Duty Cycle
0.7
0.6
40°
0.5
1.0
0.4
0.9
50°
0.8
60°
0.3
0.2
f = 38 kHz, Ee = 2 mW/m2
70°
0.1
0.7
80°
0.0
0
20
40
60
80
100
120
0.6
Burst Length (number of cycles/burst)
16913
0.4
Fig. 9 - Max. Envelope Duty Cycle vs. Burstlength
0
0.2
0.4
0.6
Fig. 12 - Directivity
0.6
Ee min. - Threshold Irradiance (mW/m²)
0.2
d rel - Relative Transmission Distance
16801
1.0
0.9
Sensitivity in dark ambient
Ee min. - Sensitivity (mW/m 2 )
0.5
0.4
0.3
0.2
0.1
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
2.0
0.0
- 30
- 15
0
15
30
45
60
75
90
Tamb - Ambient Temperature (°C)
16918
17185
Fig. 10 - Sensitivity vs. Ambient Temperature
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
VS - Supply Voltage (V)
Fig. 13 - Sensitivity vs. Supply Voltage
S ( λ) rel - Relative Spectral Sensitivity
1.2
1.0
0.8
0.6
0.4
0.2
0.0
750
16919
850
950
1050
1150
λ - Wavelength (nm)
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
Rev. 2.3, 21-Feb-12
4
Document Number: 82187
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Design
TSOP362..
www.vishay.com
Vishay Semiconductors
SUITABLE DATA FORMAT
The circuit of the TSOP362.. is designed so that unexpected
output pulses due to noise or disturbance signals are
avoided. A bandpass filter, an integrator stage and an
automatic gain control are used to suppress such
disturbances.
IR Signal
The distinguishing mark between data signal and
disturbance signal are carrier frequency, burst length and
duty cycle.
The data signal should fulfill the following conditions:
• Carrier frequency should be close to center frequency of
the bandpass (e.g. 38 kHz)
• Burst length should be 10 cycles/burst or longer
0
• After each burst which is between 10 cycles and 70 cycles
a gap time of at least 14 cycles is necessary
5
10
15
20
Time (ms)
16920
Fig. 14 - IR Signal from Fluorescent Lamp with Low Modulation
• For each burst which is longer than 1.8 ms a
corresponding gap time is necessary at some time in the
data stream. This gap time should be at least 6 times
longer than the burst
• Up to 800 short bursts per second can be received
continuously
IR Signal
Some examples for suitable data format are: NEC code
(repetitive pulse), NEC code (repetitive data), Toshiba
Micom Format, Sharp code, RC5 Code, RC6 code,
R-2000 code, Sony code.
When a disturbance signal is applied to the TSOP362.. it can
still receive the data signal. However the sensitivity is
reduced to that level that no unexpected pulses will occur.
Some examples for such disturbance signals which are
suppressed by the TSOP362.. are:
0
• DC light (e.g. from tungsten bulb or sunlight)
16921
• Continuous signal at 38 kHz or at any other frequency
10
15
20
Time (ms)
Fig. 15 - IR Signal from Fluorescent Lamp with High Modulation
• Signals from fluorescent lamps with electronic ballast with
high or low modulation (see fig. 14 or fig.15)
Rev. 2.3, 21-Feb-12
5
5
Document Number: 82187
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Design
TSOP362..
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
7.5
Pick and place area. TT taping
7.2
(1.5)
2.8
2.2
5.3
A
1
4
0.5 ± 0.15
0.1
(1.4)
0.3 4x
0.1
1.27
2.9
3 x 1.27 =
3.81
4
0.4 A
5.51
Not indicated tolerances ± 0.3
Pick and place area. TR taping
technical drawings
according to DIN
specifications
2.6
Footprint
2.35
3 x 1.27 = 3.81
0.9
2.2
1.27
R 1.7
Drawing-No.: 6.544-5341.01-4
Issue: 8; 02.09.09
16776
ASSEMBLY INSTRUCTIONS
Reflow Soldering
• Handling after reflow should be done only after the work
surface has been cooled off
• Reflow soldering must be done within 72 h while stored
under a max. temperature of 30 °C, 60 % RH after
opening the dry pack envelope
Manual Soldering
• Use a soldering iron of 25 W or less. Adjust the
temperature of the soldering iron below 300 °C
• Set the furnace temperatures for pre-heating and heating
in accordance with the reflow temperature profile as
shown in the diagram. Excercise extreme care to keep the
maximum temperature below 260 °C. The temperature
shown in the profile means the temperature at the device
surface. Since there is a temperature difference between
the component and the circuit board, it should be verified
that the temperature of the device is accurately being
measured
Rev. 2.3, 21-Feb-12
• Finish soldering within 3 s
• Handle products only after the temperature has cooled off
6
Document Number: 82187
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Design
TSOP362..
www.vishay.com
Vishay Semiconductors
VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE
300
max. 260 °C
245 °C
255 °C
240 °C
217 °C
250
T (°C)
200
max. 20 s
150
max. 100 s
max. 120 s
100
max. Ramp Up 3 °C/s
max. Ramp Down 6 °C/s
50
0
0
19800
50
100
150
t (s)
200
250
300
max. 2 cycles allowed
TAPING VERSION TSOP..TT DIMENSIONS in millimeters
16584
Rev. 2.3, 21-Feb-12
7
Document Number: 82187
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Design
TSOP362..
www.vishay.com
Vishay Semiconductors
TAPING VERSION TSOP..TR DIMENSIONS in millimeters
16585
Rev. 2.3, 21-Feb-12
8
Document Number: 82187
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Design
TSOP362..
www.vishay.com
Vishay Semiconductors
REEL DIMENSIONS in millimeters
16734
LEADER AND TRAILER DIMENSIONS in millimeters
Trailer
no devices
Leader
devices
no devices
End
Start
min. 200
min. 400
96 11818
COPER TAPE PEEL STRENGTH
LABEL
According to DIN EN 60286-3
Standard bar code labels for finished goods
0.1 N to 1.3 N
The standard bar code labels are product labels and used
for identification of goods. The finished goods are packed in
final packing area. The standard packing units are labeled
with standard bar code labels before transported as finished
goods to warehouses. The labels are on each packing unit
and contain Vishay Semiconductor GmbH specific data.
(300 ± 10) mm/min.
165° to 180° peel angle
Rev. 2.3, 21-Feb-12
9
Document Number: 82187
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Design
TSOP362..
www.vishay.com
Vishay Semiconductors
VISHAY SEMICONDUCTOR GMBH STANDARD BAR CODE PRODUCT LABEL (finished goods)
PLAIN WRITING
ABBREVIATION
LENGTH
Item-description
-
18
Item-number
INO
8
Selection-code
SEL
3
BATCH
10
Data-code
COD
3 (YWW)
Plant-code
PTC
2
Quantity
QTY
8
Accepted by
ACC
-
Packed by
PCK
-
LOT-/serial-number
Mixed code indicator
Origin
LONG BAR CODE TOP
MIXED CODE
-
xxxxxxx+
Company logo
TYPE
LENGTH
Item-number
N
8
Plant-code
N
2
Sequence-number
X
3
Quantity
N
8
Total length
-
21
SHORT BAR CODE BOTTOM
TYPE
LENGTH
Selection-code
X
3
Data-code
N
3
Batch-number
X
10
Filter
-
1
Total length
-
17
DRY PACKING
After more than 72 h under these conditions moisture
content will be too high for reflow soldering.
The reel is packed in an anti-humidity bag to protect the
devices from absorbing moisture during transportation and
storage.
In case of moisture absorption, the devices will recover to
the former condition by drying under the following condition:
192 h at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen)
Aluminum bag
or
96 h at 60 °C + 5 °C and < 5 % RH for all device containers
Label
or
24 h at 125 °C + 5 °C not suitable for reel or tubes.
An EIA JEDEC standard JSTD-020 level 4 label is included
on all dry bags.
Reel
LEVEL
CAUTION
15973
This bag contains
MOISTURE-SENSITIVE DEVICES
FINAL PACKING
4
1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative
humidity (RH)
The sealed reel is packed into a cardboard box. A secondary
cardboard box is used for shipping purposes.
2. After this bag is opened, devices that will be subjected to soldering
reflow or equivalent processing (peak package body temp. 260 °C)
must be
2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or
2b. Stored at < 5 % RH
RECOMMENDED METHOD OF STORAGE
3. Devices require baking befor mounting if:
Humidity Indicator Card is > 10 % when read at 23 °C ± 5 °C or
2a. or 2b. are not met.
Dry box storage is recommended as soon as the aluminum
bag has been opened to prevent moisture absorption. The
following conditions should be observed, if dry boxes are
not available:
4. If baking is required, devices may be baked for:
192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or
96 hours at 60 °C ± 5 °C and < 5 % RH for all device containers or
24 hours at 125 °C ± 5 °C not suitable for reels or tubes
Bag Seal Date:
(If blank, see barcode label)
Note: Level and body temperature defined by EIA JEDEC Standard JSTD-020
• Storage temperature 10 °C to 30 °C
22522
• Storage humidity  60 % RH max.
Rev. 2.3, 21-Feb-12
EIA JEDEC standard JSTD-020 level 4 label is included
on all dry bags
10
Document Number: 82187
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Not for New Design
TSOP362..
www.vishay.com
Vishay Semiconductors
ESD PRECAUTION
VISHAY SEMICONDUCTORS STANDARD
BAR CODE LABELS
Proper storage and handling procedures should be followed
to prevent ESD damage to the devices especially when they
are removed from the antistatic shielding bag. Electro-static
sensitive devices warning labels are on the packaging.
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
data.
16962
Rev. 2.3, 21-Feb-12
11
Document Number: 82187
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000