Distribution Boxes
Distribution Boards for Electrical Installation
Eaton offers installation and meter distribution boards according to customer
specification and the specific technical connection conditions. These distribution boards are in accordance with the Austrian, European, and international
standards and are approved by the Austrian Power Suppliers (EVU).
The proven installation distribution board system by Eaton (Profi Line) meets
the requirements of an easy-to-assemble electrical installation system. The
safety engineering tests were conducted according to EN 60439 and in compliance with the basic requirements of the international standard IEC 364.
• Correction possible in case of displacement of the wall box by means of
plastic inserts in the doorframe
• Quick and easy installation
• Mounting inserts and front plates can be removed after installation of the
doorframe
• Convenient earthing
• 18 mm surface levelling
• Single-wing door, for standards width 4, two-wing door
Our Range of Services
Eaton provides optimum planning and calculation assistance to the electrical
fitter through a network of regional engineering offices. Our specialists in the
area of distributing equipment provide you with calculations and offer advice
on electrical installation regulations.
Being a manufacturer of distributing equipment, Eaton offers expert advice
for complex distribution board systems or taking over a contract in the case
of a capacity bottleneck.
Our distributing equipment construction division will manufacture and wire
any distribution board system, also according to customer specification, at
short notice and competitive prices.
As responsible manufacturers, importers and dealers, we want to ensure that
our distributing equipment is in compliance with the relevant EU regulations
and bears the
-mark.
Splash-proof doorframe TFN:
• Degree of protection IP54, insulated splash-proof version
• Sheet aluminium
• Phosphatised and polyester powder coated
• Colours RAL 7035 and RAL 9010 (limited)
Special colour: plus 15%, available at short notice!
• Stable, reinforced door with hinges
• mounting ledge for mounting devices unto the door (type ASS),
easy to fasten
• Twist lock, from standard height 1700 on also with 3-point rod lock with
pivoting lever (semi-cylinder lock can be installed)
• From standard height 1150, 3 twist locks
• Correction possible by means of plastic inserts in the doorframe in case of
displacement of the wall box
• Quick and easy installation
• Mounting inserts and front plates can be removed after installation of the
doorframe
• Convenient earthing
• 18 mm surface levelling
• Single-wing door, for standard width 4, two-wing door
Wall box MW:
• Depth 240 or 180 mm
• Galvanised sheet steel
• Rear wall on order (RWN ….K, ST)
• Supplied in pieces, little storage space required
• Recesses can be broken out easily and securely on all four side walls
• C-mounting rail with trough offers protections against lateral indentations
• Easy to assemble (pre-assembled parts)
• Many earth connection options make the installation easier
• Ready for installation of the Profi Line mounting frame
• Depth: 240 mm:
Standard width 5, mounting inserts of standard widths 2 and 3 can be
installed on the right or on the left.
The mounting inserts can be installed in a deeper position if devices/
equipment mounted unto the door reach deeply inside the cabinet
Surface-type Standard Distribution Boards ON:
• Degree of protection IP40
• Depth 250 mm
• Rear wall to be ordered separately (RWN …. K, ST)
• Sheet steel
• Phosphatised and polyester powder coated
• Colours RAL 7035 and RAL 9010 (limited)
Special colour: plus 15%, available at short notice!
• Stable, reinforced door with hinges on the right or left
• mounting ledge for mounting devices unto the door (type ASS),
easy to fasten
• Twist lock
• 3 twist locks from standard height 1500 on
• 45 mm leading-in opening in the upper wall or lower wall possible by
turning the distribution board through 180°
• immersed door, hence no base required
• ready for installation of the Profi Line mounting frame
• Standard width 5, optional installation of the mounting inserts of standard
widths 2 and 3 to the left or right
• Cabinet available with window upon request
Doorframe TRN:
• Degree of protection IP40
• Sheet steel
• Phosphatised and polyester-powder coated
• Colours RAL 7035 and RAL 9010 (limited)
Special colour: plus 15%, available at short notice!
• Stable, reinforce door, optionally hinged to the left or to the right
• Mounting ledge for mounting devices unto the door (type ASS),
easy to fasten
• Twist lock, from standard height 1700 on also with 3-point rod lock with
pivoting lever (semi-cylinder lock can be installed)
• From standard height 1500, 3 twist locks
• Correction by means of plastic inserts in the doorframe possible in case of
displacement of the wall box
• Quick and easy installation
• Mounting inserts and front plates can be removed after installation of the
doorframe
• Convenient earthing
• 18 mm surface levelling
• Single-wing door, for standards widths 4 and 5, two-wing door
Splash-Proof Surface-Type Distribution Boards OFN:
• Degree of protection IP54
• Depth 250 mm
• Rear wall and blind flange
• Polyester powder coated sheet steel
• Colours RAL 7035 and RAL 9010 (limited)
Special colour: plus 15%, available at short notice!
• Stable, reinforced door with hinges on the right or left
• mounting ledge for mounting devices unto the door (type ASS),
easy to fasten
• Twist lock
• 3 twist locks from standard height 1500 on
• immersed door, hence no base required
• Standard width 5, optional installation of the mounting inserts of standard
widths 2 and 3 to the left or right
• Leading-in flanges:
For standard width 2
1 pc.
For standard width 3 and 4
2 pcs.
For standard width 5
3 pcs.
Door for outdoor installation TLN:
• Degree of protection IP43, outdoor version with stormwater deflector
• Sheet aluminium
• Phosphatised and polyester powder coated
• Colours RAL 7035 and RAL 9010 (limited)
Special colour: plus 15%, available at short notice!
• Stable, reinforced door with hinges
• mounting ledge for mounting devices unto the door (type ASS),
easy to fasten
• Twist lock, from standard height 1700 on also with 3-point rod lock with
pivoting lever (semi-cylinder lock can be installed)
• From standard height 1500, 3 twist locks
1
Distribution Boxes
Stand-Alone Distribution Boards ON and OFN:
• Degree of protection IP40 (ON), IP54 (OFN) slash-proof type
Note: For protection system IP54 (OFN-./1950/300..), close *) the bottom
openings with leading-in flanges for splash-proof surface-type distribution
boards F3A-… (to be ordered separately)
Delivered as OFN-./1950/300..:
Frontal leading-in openings: to be closed with F3A-0*),
Bottom openings: open
*) Number see dimension illustration 'Dimensions for cable entry'
• Standard height 1950
• Depth 250 mm in ./1950/250 mm types
300 mm in ./1950/300 mm types
400 mm in ./1950/400 mm types
• Rear wall to be ordered separately (RWN …. K, ST)
• Rear wall included with OFN
• Sheet steel
• Phosphatised and polyester powder coated
• Colours RAL 7035 and RAL 9010 (limited)
Special colour: plus 15%, available at short notice!
• Including stable, reinforced door with hinges on the right or left
• Twist lock or three-point rod lock with pivoting lever
• immersed door, hence no base required
• Standard width 5, optional installation of the mounting inserts of standard
widths 2 and 3 to the left or right
• Cabinet available with window upon request
Standard Open Distribution Boards MN:
• Depth 190 mm
• Degree of protection IP30
• Sheet steel
• Phosphatised and polyester powder coated
• Colour RAL 7035 (standard)
Special colour: plus 15%, available at short notice!
• Rear wall to be ordered separately (RWN …. K, ST)
• Ready for installation of the Profi Line mounting insert
Rear walls RWN … K:
• For stand-alone, flush-type, surface-type and open distribution boards
• Light-weight, insulating plastic rear wall
• Easy to install by gluing unto the enclosure
Rear walls RWN … ST:
• For stand-alone, flush-type, surface-type and open distribution boards
• Stable, galvanised sheet steel rear wall
• Easy to install by gluing unto the enclosure
• Attention! Ensure earthing of sheet steel rear walls by riveting or screwing
Mounting Inserts MES:
• Including sheet steel or plastic front plates
• Details and front plate components see price lists 'EVU Main Distribution
Box')
Technical Data
Electrical
Design in accordance with
Variations
Degree of protection
Rated voltage
Air gaps and leakage paths
Mechanical
Material:
Paint finish
EN 60439, EN 50298
Flush-type, surface-type, and
open* distribution boards
IP40, IP43 or IP54, (*IP30)
according to ÖVE-EN 60529
400V~ / 50Hz
according to VDE 0110, Parts
1+2/1.89 corresponding to overvoltage category IV, pollution
degree 2, insulating materials II
and IIa, rated voltage 400V~
Colour
Free space for devices mounted onto the door
Free depth (mm) between front plates sheet steel (FS)*) and:
Flat distribution board Distr. board f. electrical installation
FVTN FVT-ON
Flush-mounted ON/OFN
Door
31
Reinforced door –
*)
39
–
55
57
40
42
at removal backward MSWposition: +30 mm depth
By using of plastic front plates (FKN) the free space reduces about 2 mm.
2
Steel or aluminium sheet
Phosphatised and polyester
powder coated
RAL 7035 and RAL 9010 (limited)
Special colour: plus 15%,
available at short notice!
Distribution Boxes
Dimensions (mm) and Types
Standard width
1
MU per block FS/45 (FKN/45)
14
2
21
3
33
4
47
5
Depth
(44) 59 [33+21] (56)
Inside dimensions
(insert)
330
460
670
920
1130
115
415
Recess dimensions (recommended) 440
544
570
754
780
1005
1030
1215
1240
245/185*)
245/185*)
444
574
784
1034
1244
—
444
574
784
1034
—
—
434
564
774
1024
1234
250**)
383
513
723
973
—
190
Standard height
.
Outside dimensions MW wall box
Outside dimensions
TRN Doorframe
TLN, TFN Doorframe
ON, OFN Flush-type
400
—
—
—
—
—
—
—
MW-2/350*)
TRN-2/350
TLN-2/350
TFN-2/350
ON-2/350
OFN-2/350
MN-2/350
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
700
MW-1/650*)
TRN-1/650
TLN-1/650
—
—
—
—
MW-2/650*)
TRN-2/650
TLN-2/650
TFN-2/650
ON-2/650
OFN-2/650
MN-2/650
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
900
MW-1/850*)
TRN-1/850
TLN-1/850
—
ON-1/850
—
MN-1/850
MW-2/850*)
TRN-2/850
TLN-2/850
TFN-2/850
ON-2/850
OFN-2/850
MN-2/850
MW-3/850*)
TRN-3/850
TLN-3/850
TFN-3/850
ON-3/850
OFN-3/850
MN-3/850
MW-4/850
TRN-4/850
—
—
ON-4/850
OFN-4/850
MN-4/850
—
—
—
—
—
—
—
1050
MW-1/1000*)
TRN-1/1000
TLN-1/1000
—
ON-1/1000
—
MN-1/1000
MW-2/1000*)
TRN-2/1000
TLN-2/1000
TFN-2/1000
ON-2/1000
OFN-2/1000
MN-2/1000
MW-3/1000*)
TRN-3/1000
TLN-3/1000
TFN-3/1000
ON-3/1000
OFN-3/1000
MN-3/1000
MW-4/1000
TRN-4/1000
TLN-4/1000
TFN-4/1000
ON-4/1000
OFN-4/1000
MN-4/1000
—
—
—
—
—
—
—
1200
MW-1/1150*)
TRN-1/1150
TLN-1/1150
—
—
—
—
MW-2/1150*)
TRN-2/1150
TLN-2/1150
TFN-2/1150
ON-2/1150
OFN-2/1150
MN-2/1150
MW-3/1150*)
TRN-3/1150
TLN-3/1150
TFN-3/1150
ON-3/1150
OFN-3/1150
MN-3/1150
MW-4/1150
TRN-4/1150
TLN-4/1150
TFN-4/1150
ON-4/1150
OFN-4/1150
MN-4/1150
MW-5/1150
TRN-5/1150
—
—
ON-5/1150
OFN-5/1150
—
1350
—
—
—
—
—
—
—
MW-2/1300
TRN-2/1300
TLN-2/1300
TFN-2/1300
ON-2/1300
OFN-2/1300
MN-2/1300
MW-3/1300
TRN-3/1300
TLN-3/1300
TFN-3/1300
ON-3/1300
OFN-3/1300
MN3/1300
MW-4/1300
TRN-4/1300
—
—
ON-4/1300
OFN-4/1300
MN-4/1300
MW-5/1300
TRN-5/1300
—
—
ON-5/1300
OFN-5/1300
—
1550
—
—
—
—
—
—
—
MW-2/1500
TRN-2/1500
TLN-2/1500
TFN-2/1500
ON-2/1500
OFN-2/1500
MN-2/1500
MW-3/1500
TRN-3/1500
TLN-3/1500
TFN-3/1500
ON-3/1500
OFN-3/1500
MN-3/1500
MW-4/1500
TRN-4/1500
—
—
ON-4/1500
OFN-4/1500
MN-4/1500
MW-5/1500
TRN-5/1500
—
—
ON-5/1500
OFN-5/1500
—
1750
—
—
—
—
—
—
—
MW-2/1700
TRN-2/1700
—
—
ON-2/1700
OFN-2/1700
MN-2/1700
MW-3/1700
TRN-3/1700
TLN-3/1700
TFN-3/1700
ON-3/1700
OFN-3/1700
MN-3/1700
MW-4/1700
TRN-4/1700
—
—
ON-4/1700
OFN-4/1700
MN-4/1700
MW-5/1700
TRN-5/1700
—
—
ON-5/1700
OFN-5/1700
—
2000
454
754
954
1104
1254
1404
1604
1804
2054
464
764
964
1114
1264
1414
1614
1814
2064
464
764
964
1114
1264
1414
1614
1814
2064
435
460
735
760
935
960
1085
1110
1235
1260
1385
1410
1585
1610
1785
1810
2035
2060
350
650
850
1000
1150
1300
1500
1700
1950
1950
1700
1500
1300
1150
1000
850
650
350
MN Open type
—
—
—
—
—
—
—
MW-2/1950
TRN-2/1950
—
—
ON-2/1950
OFN-2/1950
MN-2/1950
MW-3/1950
TRN-3/1950
TLN-3/1950
TFN-3/1950
ON-3/1950
OFN-3/1950
MN-3/1950
MW-4/1950
TRN-4/1950
—
—
ON-4/1950
OFN-4/1950
MN-4/1950
MW-5/1950
TRN-5/1950
—
—
ON-5/1950
OFN-5/1950
—
*) also available at 185 mm depth
**) flush-type distribution boards of standard height 1950 are 250, 300 or 400 mm deep. Doors from standard height >1500 on also available with pivoting lever.
3
Distribution Boxes
Dimensions (mm) for cable entry
no lateral cable entries
Wall box MW, depth 180 mm
side face
Inner*-depth MW (* between MSW-front
[level of frontplates] and RW-inside):
front MSW-position: 125 mm
back MSW-position (-30 mm): 95 mm
4
Distribution Boxes
Dimensions (mm) for cable entry
206 (at 350-1500)
306 (at 1700 and 1950)
Wall box MW, depth 240 mm
side face
Inner*-depth MW (* between MSW-front
[level of frontplates] and RW-inside):
front MSW-position: 185 mm
back MSW-position (-30 mm): 155 mm
5
Distribution Boxes
Dimensions (mm) for cable entry
Surface-type standard distribution board ON, 250 mm deep
top
front
front
top
front
top
top
front
front
top
All front parts ON-250 closed at the bottom
6
Distribution Boxes
Dimensions (mm) for cable entry
Splash-proof surface-type distribution board OFN, depth 250 mm
top
front
front
top
top
front
front
top
All front parts OFN-250 closed at the bottom
7
Distribution Boxes
Dimensions (mm) for cable entry
Stand-alone distribution board ON -/1950/…, depths 300 mm and 400 mm
thread
above, below
front
front
thread
above, below
above, below
front
front
thread
thread
above, below
8
Distribution Boxes
Dimensions (mm) for cable entry
Splash-proof stand-alone distribution boards OFN -/1950/…, 300 mm deep
thread
above, below
front
front
thread
above, below
thread
above, below
front
front
thread
above, below
9
Distribution Boxes
Dimensions (mm) for cable entry
Standard open distribution boards MN, depth 190 mm
front
top
top
front
front
top
front
top
all, without 1950
at 1950
All front parts MN-190 closed at the bottom
10
Distribution Boxes
Dimensions (mm) Mounting System
module vertical 12.5 mm
support rail aluminium TSA
or the universal
support rail steel TSS
module horizontal
depth strap propped up at the back of the cabinet
12 mm
additional levels using TSA
mounting levels using TSS, TSA
depth strap
continuous
adjustment
11
Distribution Boxes
Dimensions (mm) Mounting System
1st level
2nd level
Switching devices: lower depth than
Xpole
Switching devices: frame size
45 mm
4th level
3rd level
KKW cable duct support strap for vertical duct
TSC 8 C-rail for horizontal duct
switching devices: frame size 80 mm
5th level
fastened with TSA rail at the back
Contactor. Contactor with auxiliary
contact under the front plate
5th level
with compensation adaptor
Breaker 00 with
busbar set
front level for TB-LTS00 support rail
5th level
fastened with TSA rail at the back
125 mm = 5 module units
Breaker
LTS 160/00
Contactor. Contactor with auxiliary contact
back level for TB-LTS00 support rail
200 mm = 8 module units
F&G breaker
LTS 160/00
2nd level
Switching devices: 45 mm frame size
SA busbar set
SAA
SAA
12
Distribution Boxes
Mounting Inserts MES
350
Standard width 1
3
4
5
standard height
MES-2/350
42MU
MES-1/650
MES-2/650
42MU
63MU
MES-1/850
MES-2/850
MES-3/850
MES-4/850
56MU
84MU
132MU
188MU
MES-1/1000
MES-2/1000
MES-3/1000
MES-4/1000
56MU
84MU
132MU
188MU
MES-1/1150
MES-2/1150
MES-3/1150
MES-4/1150
MES-5/1150
70MU
105MU
165MU
235MU
270MU
MES-2/1300
MES-3/1300
MES-4/1300
MES-5/1300
105MU
165MU
235MU
270MU
MES-2/1500
MES-3/1500
MES-4/1500
MES-5/1500
105MU
165MU
235MU
270MU
standard height
1500
standard height
1300
standard height
1150
standard height
1000
standard height
850
standard height
650
2
13
Distribution Boxes
2
3
4
5
MES-2/1700
MES-3/1700
MES-4/1700
MES-5/1700
standard height
1700
Standard width 1
231MU
329MU
378MU
MES-2/1950
MES-3/1950
MES-4/1950
MES-5/1950
147MU
231MU
329MU
378MU
standard height
1950
147MU
Outdoor Distribution Boxes, to be mounted on a Base IP43, VF
• Cover height 850 mm
• Including rain-proof cover
• Ready for installation of the Profi Line mounting frame
Technical Data
Mechanical
Material
Degree of protection
Colour
powder-coated aluminium
IP43
RAL 7035
Dimensions (mm)
VF-1/850
VF-3/850
VF-1/1000
VF-2/1000
VF-3/1000
W
437
777
437
567
777
H
913
913
1063
1063
1063
D
250
320
250
320
320
14
Distribution Boxes
Distribution Boxes Accessories
Lateral Support Wall MSW, Support Rails TS., Cable Duct Angles KKW
Slotted Steel Sheet Mounting Panels MPN
15
Type
MPN-2/050
MPN-3/050
MPN-4/050
MPN-5/050
B
411
621
872
1082
Type
MPN-2/080
MPN-3/080
MPN-4/080
MPN-5/080
B
411
621
872
1082
Type
MPN-2/130
MPN-3/130
MPN-4/130
MPN-5/130
B
411
621
872
1082
Distribution Boxes
Steel Sheet Mounting Plates MPL
Type
MPL-2/350
MPL-3/350
MPL-4/350
B
365
575
826
Type
MPL-2/850
MPL-3/850
MPL-4/850
B
365
575
826
Type
MPL-2/650
MPL-3/650
MPL-4/650
B
365
575
826
Leading-in flanges for splash-proof surface-type standard distribution boxes, F3A
VT17407
VT09208
VT17507
VT17307
F3A-0
Blind flange
F3A-XP
Blind flange sheet steel
F3A-4
4xM16, 6xM25/16, 8xM32/20
F3A-8
2xM20, 8xM25/16, 4xM32/20,
1xM50/32
VT17607
VT17707
VT17807
VT17207
F3A-12
2xM16, 12xM20, 2xM40/25, 2xM50/32
F3A-34
24xM16, 13xM20
F3A-KTD
2 grommets for cables
up to Ø 70 mm
F3A-D
Cellular rubber pass-through flange,
40 cables of Ø 10-13 mm,
4 cables of Ø 17-21 mm,
2 cables of Ø 27-30 mm
16
Distribution Boxes
Sheet Steel Front Plates for HRC Load Breakers, FTRN
FTR
Dimensions (mm)
Standard width
A
324
B
460
C
324
D
—
2
570
670
570
—
3
791
920
433
324
4
*)
*) Height of device recess 160 mm, for
LTS-160/00/3(-R)
Front Plates With 45 mm Device Recess
Sheet steel FS/45
10494a
Dimensions (mm)
Standard width
5
14MU
A
251
B
330
1
2
3
4
21MU
381
460
33MU
591
670
47MU
841
920
59MU
1051
1130
1
2
3
4
21MU
381
460
—
33MU
590
670
—
44MU
842
920
50
56MU
1052
1130
50
1MU = 17.5 mm
Plastic FKN/45
10494a
Dimensions (mm)
Standard width
5
14MU
A
254
B
330
C
—
1MU = 17.5 mm
Front Plates Without Device Recess
Sheet steel FS
FS
Dimensions (mm)
Standard width
5
B
330
1
2
3
4
460
670
920
1130
1MU = 17.5 mm
Plastic FKN
FS
Dimensions (mm)
Standard width
5
B
330
1
2
3
4
460
670
920
1130
1MU = 17,5mm
17
Distribution Boxes
Terminal Sets KS
42673
42706
KS-5
• 4 x strip terminal KL-7 on support KT-4
• 4 x 6 terminal points
KS-1
• 1 x strip terminal KL-7 on support KT-1
• 6 terminal points
427010
42446
KS-2
• 1 x strip terminal KL-15 on support KT-1
• 14 terminal points
KS-6
• 2 x strip terminal KL-29, 2 x support KT-3 plus
fastening screws
• 2 x 27 terminal points
42703
42699
KS-8
• 2 x strip terminal KL-7 on support KT-4
• 2 x 6 terminal points
KS-3
• 2 x strip terminal KL-15 on support KT-4
• 2 x 14 terminal points
426912
KS-4
• 2 x strip terminal KL-7 and 1 x strip terminal KL15 on support KT-4
• 2 x 6 terminal points, 1 x 14 terminal points
Terminal supports KT
42709
42676
KT-1
• mounted lengthwise and crosswise onto hollow
rails using support KT-11, suitable up to KL-15
KT-4
• for strip terminals up to KL-15, mounted onto
flat rails, mounted lengthwise or crosswise onto
hollow rails, or crosswise on DIN rails according
to IEC/EN 60715
42679
42726
KT-2
• for strip terminals KL-7 up to KL-60 or flat copper
of up to 20 mm width, mounted onto flat or
hollow rails
KT-5
• for strip terminals up to KL-15, for vertical snapon mounting onto DIN rails according to
according to IEC/EN 60715
9603412
42727
KT-11
• Support for terminal support KT-1
KT-3
• for strip terminals KL-7 up to KL-60, mounted
onto flat or hollow rails
Terminal Blocks KL
• Scope of delivery: 1 Terminal Block
VT01905
Type
KL-7
KL-15
KL-29
KL-45
KL-60
KLM
Length (mm)
59
115
219
331
443
1000
Number of terminals
6 x 16mm2, 1 x 25mm2
13 x 16mm2, 2 x 25mm2
27 x 16mm2, 2 x 25mm2
43 x 16mm2, 2 x 25mm2
58 x 16mm2, 2 x 25mm2
n x 16mm2
KLA
connection terminal for 35mm2
18
Distribution Boxes
Mounting Plate for Stand-alone Distribution Box ZST-MP
Type
ZSD-MP-2
ZSD-MP-3
ZSD-MP-4
ZSD-MP-5
19
A
398
608
859
1069
B
475
685
932
1146
C
25
25
30
30
Add-On Distribution Boards
XVTL Technical Data
Electrical
Standards
IEC/EN 60439-1, IEC/EN 60439-3, IEC/EN 62208, IEC/EN 61439-1/2
Safety measure
Protection class I
Rated insulation voltage Ui
600 V
Rated operational voltage Ue
415 V
Rated impulse voltage Uimp
6 kV
Overvoltage category
IV
Pollution degree
3
Rated frequency
50Hz / AC
Rated current Ie (busbars)
up to 2500 A
Rated short-time withstand current Icw
65 kA (1s)
Rated peak withstand current Ipk
143 kA
Earth connections I2t
Base frame: Main earthing point - M10 screw
50 x 106 A2s
Side/rear panel: M6 taptite screw
3.9 x 106 A2s per screw
Door: M6 welding bolt
4.68 x 106 A2s
Maximum power loss for all devices integrated in the distribution board (W) IP40/IP55 closed (side wall, rear wall, top, door)
Height (mm)
Width x Depth (mm) 1400 1600 1800 2000
425 x 300
201
233
425 x 400
301
425 x 500
357
425 x 600
395
425 x 800
483
600 x 300
242
268
305
355
600 x 400
333
370
383
600 x 500
408
432
600 x 600
436
456
483
600 x 800
581
800 x 300
371
391
408
800 x 400
420
441
466
800 x 500
499
537
800 x 600
527
569
581
800 x 800
669
850 x 300
430
850 x 400
492
850 x 500
511
850 x 600
600
850 x 800
691
1000 x 300
435
461
499
1000 x 400
500
534
553
1000 x 500
592
607
1000 x 600
616
636
658
1000 x 800
762
1100 x 300
527
1100 x 400
584
1100 x 500
644
1100 x 600
699
850 x 800
812
1200 x 300
513
545
557
1200 x 400
594
604
622
1200 x 500
656
683
1200 x 600
675
706
742
1200 x 800
866
1350 x 300
604
1350 x 400
677
1350 x 500
744
1350 x 600
811
1350 x 800
955
Difference in temperature 35 K, free standing enclosure, closed without ventilation openings and horizontal division
Dimensions (mm).
20
Add-On Distribution Boards
Mechanical
Application
Installation conditions
Dimensions
Height
Width
Depth
Degree of protection
Environmental conditions
Short-time maximum value
Maximum (24h mean value)
Minimum value
Humidity
Material
Paint
Colour
Door
Door lock
Cable entry
Scope of delivery
Floor-standing enclosure for stand-alone or add-on installation for setting up a low-voltage distribution
board; removable rear and side panels
Indoor installation
1400, 1600, 1800, 2000
425, 600, 800, 850, 1000, 1100, 1200, 1350
300, 400, 500, 600, 800
IP40 or IP55, IK10
+40°C (104°F)
+35°C (95°F)
-5°C (23°F)
50% at 40°C (104°F)
Sheet steel
Phosphatised and polyester-powder-coated
RAL 7035
Outside-supported doors with hidden hinges, as of an angle of 90° they can be unhinged; as of a width of
1000 mm use two doors, 120° opening angle (even in case of several cabinets mounted side by side)
Clip-down handle with rod lock, can be fitted with a semi-cylinder lock 3-point
Different bottom and top covers permit cable insertion from below and/or above
• XVTL-BF..: Frame, door, rear panel and top cover
pre-assembled or in single parts
21
Add-On Distribution Boards
XVTL Add-On Distribution Boards, IP40 Degree of Protection
XVTL-BF Basic Fragmentary Equipment:
• Scope of delivery: Frame, doors, rear panel, top cover, no side panels and no
bottom cover
• Designation e.g.: XVTL-BF-4/4/20
xBoard add-on distribution board light - basic fragmentary equipment,
width 425, depth 400, height 2000
• Material: Frame of 2 mm sheet steel, door of 1.25 mm sheet steel, rear
panel of 1.5 mm sheet steel
• Phosphatised and polyester-powder-coated
• Colour: RAL 7035
• Weight (kg):
Width
425
600
800
1000
1200
Height 1600 1800 2000 1400 1600 1800 2000 1600 1800 2000 1600 1800 2000 1600 1800 2000
Depth 300 50 – 55 47 53 59 65 68 74 80 83 89 95 98 104 110
Depth 400 – – 56 – 55 61 67 70 76 82 85 91 97 102 108 114
Depth 500 – – 57 – – 62 68 – 77 83 – 93 99 – 112 118
Depth 600 – – 59 – 58 64 70 74 80 86 88 94 100 111 117 123
Depth 800 – – 62 – – – 73 – – 89 – – 105 – – 127
• Add-on options:
Side panel, bottom cover
• Installation options:
Profi+ vertical profiles, Profi+ mounting plates, Profi+ mounting inserts,
IVS-support system, plinth, fastening brackets, cable strain relief rails,
mounting set for ITMX16, IZM20, IZM32, IZM1 and 2, IZM58 size 5 and 6,
door arrester, bottom cover
XVTL-S Side Panels:
• Purpose: Side panels for IP40 degree of protection according to
IEC/EN 60529 and IEC/EN 529, designed for the end of a series of cabinets
• Material: 1.5 mm sheet steel
• Phosphatised and polyester-powder-coated
• Colour: RAL 7035
• Weight (kg):
Depth
300
400
500
600
800
7.4
8.3
10.7
13.1
17.5
• Fastening from outside with thread-grooving, self-earthing countersunk
screws
XVTL-R Rear Panels:
• Purpose: Rear panels for IP40 degree of protection according to
IEC/EN 60529 and IEC/EN 529
• Material: 1.5 mm sheet steel
• Phosphatised and polyester-powder-coated
• Colour: RAL 7035
• Weight (kg):
Width
425
600
800
850
1000 1100 1200 1350
13.5 16
19
22
27
• Fastening from outside with thread-grooving, self-earthing countersunk
screws
XSPBM Top-Bottom Cover:
• Material: 1.25 mm sheet steel
• Phosphatised and polyester-powder-coated
• Inclusive screws
• Class of protection: IP30
• Weight (kg):
Width
425
600
800
850
Depth 300
1.1
1.7
2.7
Depth 400
1.4
2.2
3.2
Depth 500
1.6
2.4
3.3
Depth 600
2.0
2.9
4.0
Depth 800
2.7
4.0
5.5
1000
3.4
4.0
4.2
5.1
7.7
1100
1200
4.2
5.1
5.2
6.2
8.4
1350
XAD Top Cover:
• Material: 1.25 mm sheet steel
• Phosphatised and polyester-powder-coated
• Inclusive screws
• Class of protection: IP31
• Weight (kg):
Width
425
600
800
850
Depth 300
2.0
3.9
4.25
Depth 400
3.0
4.75 6.0
Depth 500
4.0
5.6
7.75
Depth 600
5.0
6.5
9.5
Depth 800
7.0
8.25 13
1000
6.0
8.0
10
12
16
1100
1200
8.0
10
12
14
18
1350
Dimensions (mm).
22
Add-On Distribution Boards
XVTL Add-On Distribution Boards, IP55 Degree of Protection
XVTL-MP/BF Basic Fragmentary Equipment:
• Scope of delivery: Frame, doors, rear panel, top cover, no side panels and
no bottom cover
• Designation e.g. XVTL-MP/BF-4/4/20
xBoard add-on distribution board light - moist-proof basic fragmentary
equipment, width 425, depth 400, height 2000
• Material: Pluged frame of 2 mm sheet steel, door of 1.25 mm sheet steel,
rear panel of 1.5 mm sheet steel
• Phosphatised and polyester-powder-coated
• Colour: RAL 7035
• Weight (kg):
Width
425
600
800
1000
1200
Height 1600 1800 2000 1400 1600 1800 2000 1600 1800 2000 1600 1800 2000 1600 1800 2000
Depth 300 52 – 56 49 55 61 67 70 76 82 84 90 96 99 105 111
Depth 400 – – 57 – 56 62 68 71 77 83 86 92 98 103 109 115
Depth 500 – – 58 – – 63 69,5 – 78 84 – 94 100 – 113 119
Depth 600 – – 60 – 59 65 71 75 81 87 89 95 101 112 118 124
Depth 800 – – 63 – – – 74 – – 90 – – 106 – – 128
• Add-on options:
Side panel, bottom cover
• Installation options:
Profi+ vertical profiles, Profi+ mounting plates, Profi+ mounting inserts,
IVS-support system, EP-support system, plinth, fastening brackets, cable
strain relief rails, mounting set for IZMX16, IZM20, IZM32, IZM1 and 2,
IZM58 size 5 and 6, door arrester, bottom cover
XVTL-MP/BF/IC Basic Fragmentary Equipment:
• Scope of delivery: Frame, doors (flat version), rear panel, top cover (closed),
bottom cover, mounting plate 3 mm, eye bolts for transportation by crane,
5 mm two-way key bit
• Designation e.g. XVTL-MP/BF/IC-6/4/20
xBoard add-on distribution board light - moist-proof basic fragmentary
equipment, installation console, width 600, depth 400, height 2000
• Material: Plugged frame of 2 mm sheet steel
• Mounting plate of 3 mm sheet steel
• Phosphatised and polyester-powder-coated
• Colour: RAL 7035
• Weight (kg):
Width
425
600
800
1000
1200
Height 1600 1800 2000 1400 1600 1800 2000 1600 1800 2000 1600 1800 2000 1600 1800 2000
Depth 300 70 – 80 67 73 79 85 93 99 105 115 121 127 115 141 147
Depth 400 – – 81 – 74 80 86 94 100 106 119 125 131 119 145 151
Depth 500 – – 82 – – 81 87 – 101 107 – 129 135 – 149 155
Depth 600 – – 84 – 78 83 89 98 104 110 124 130 136 124 154 160
Depth 800 – – 88 – – – 93 – – 113 – – 140 – – 164
• Installation options:
Profi+ vertical profiles, plinth, fastening brackets, cable strain relief rails, door
arrester, bottom cover
XVTL-D Doors:
• Material: 1.25 mm sheet steel
• Phosphatised and polyester-powder-coated
• Supplied with screws
XVTL-MP/BF-././...-IVS Basic Fragmentary Equipment:
• Colour: RAL 7035
• Scope of delivery: Frame, doors, rear panel, top cover (prepared for flanges
F3A), Support System to accomodate the IVS installation units, Frame
• Degree of protection: IP55
Covers and pre-mounted insulated support brackets
• Weight (kg):
Width
425
600
800
850
1000 1100 1200 1350
• Designation e.g. XVTL-MP/BF6/4/20-IVS
(Height 2000) 13
19
25
17
20
xBoard add-on distribution board light - moist-proof basic fragmentary
equipment, width 600, depth 400, height 2000, installation distribution sys- • Installation of doors:
Use a single-wing door up to a width of 800 mm. As of a width of
tem
1,000 mm, use a double-wing door. The right and left wing must be ordered
• Material: Frame of 2 mm sheet steel, door of 1.25 mm sheet steel, rear
separately.
panel of 1.5 mm sheet steel
• Phosphatised and polyester-powder-coated
XSDMC Doors:
• Colour: RAL 7035
• Material: 2 mm sheet steel
• Weight (kg):
Width
425
600
800
1200
• Phosphatised and polyester-powder-coated
Height 1600 2000 1600 2000 1600 2000 1600 2000
• Supplied with fastening material
Depth 300 70 74 74 88 97 111 134 147
• Colour: RAL 7035
Depth 400 82 87 87 102 109 125 147 162
• Degree of protection: IP55
• Installation options:
• Weight (kg):
Width
425
600
800
850
1000 1100 1200 1350
IVS installation units, Plinth Panels, bottom cover
(Height 2000) 18
26
34
43
52
XVTL-MP/BF-././..-EP Basic Fragmentary Equipment:
• Installation of doors:
• Scope of delivery: Frame, doors, rear panel, top cover (prepared for flanges
Use a single-wing door up to a width of 1,000 mm (1000 mm kann einF3A), Support System to accomodate the EP installation units, Frame
oder zweiflügelig gewählt werden). As of a width of 1,000 mm, use a douCovers
ble-wing door. The right and left door (both) must be ordered with one arti• Designation e.g.: XVTL-MP/BF/6/4/20-EP
cle number.
xBoard add-on distribution board light - moist-proof basic fragmentary
XVTL-MP/S and XAW Side Panels:
equipment, width 600, depth 400, height 2000, EP installation system
• Purpose: Side panels for IP55 degree of protection according to
• Material: Frame of 2 mm sheet steel, door of 1.25 mm sheet steel, rear
IEC/EN 60529 and IEC/EN 529, designed for the end of a series of cabinets
panel of 1.5 mm sheet steel
• Material: 1.5 mm sheet steel
• Phosphatised and polyester-powder-coated
• Phosphatised and polyester-powder-coated
• Colour: RAL 7035
• Colour: RAL 7035
• Weight (kg):
Width
425
600
850
1100
1350
• Weight (kg):
Depth
300
400
500
600
800
Height 2000
2000
2000
2000
2000
7.5
8.4
10.8
13.2
17.6
Depth 300 61
71
90
109
133
• Fastening from outside with thread-grooving, self-earthing countersunk
Depth 400 66
77
95
115
138
screws
Depth 500 71
83
100
121
143
Depth 600 76
89
106
127
148
Depth 800 87
99
118
144
170
• Installation options:
EP installation units, Cable Strain Relief Rails, Door Arrester Set , bottom
cover
23
Add-On Distribution Boards
XVTL-MP/R and XSWC Rear Panels:
• Purpose: Rear panels for IP55 degree of protection according to
IEC/EN 60529 and IEC/EN 529
• Material: 1.5 mm sheet steel
• Phosphatised and polyester-powder-coated
• Colour: RAL 7035
• Weight (kg):
Width
425
600
800
850
1000 1100 1200 1350
9
16
24
32
40
• Fastening from outside with thread-grooving, self-earthing countersunk
screws
XVTL-MP/T and CSPTC Top Cover:
• Material: 1.25 mm sheet steel
• Phosphatised and polyester-powder-coated
• Supplied with screws
• Colour: RAL 7035
• Degree of protection: IP55
• Weight (kg):
Width
425
600
800
850
Depth 300
1.5
2.0
2.9
Depth 400
1.5
2.3
3.2
Depth 500
1.9
2.3
4.1
Depth 600
2.3
3.6
5.0
Depth 800
3.2
5.0
6.8
1000
3.7
4.0
5.1
6.3
8.6
1100
1200
4.7
5.0
6.1
7.8
10.7
1350
XVTL-MP/T/EF Top Cover:
• Top cover with cut-outs prepared for the F3A cable insertion flange
• Material: 1.25 mm sheet steel
• Phosphatised and polyester-powder-coated
• Supplied with screws
• Colour: RAL 7035
• Degree of protection: IP55 (with F3A cable insertion flange)
• Weight (kg):
Width
425
600
800
850
1000 1100 1200 1350
Depth 300
1.4
1.8
2.6
3.3
4.2
Depth 400
1.4
2.1
2.9
3.6
4.5
Depth 500
1.8
2.8
3.8
4.7
5.6
Depth 600
2.2
3.4
4.7
5.9
7.3
Depth 800
3.1
5.8
6.5
8.1
10.2
Mechanical Loads
• If you use a xBoard Profi+ mounting frame (with XVTL-BP), the weight on
the insert must not exceed 150 kg. The weight on mounting plates covering
the entire height must not exceed 200 kg.
• Transformers and circuit breakers of higher weight (more than 40 kg per
device) must be mounted by means of depth-profiles and suitable supports
or mounting plates in order to ensure a balanced distribution of the weight
over the four corner posts.
• The total weight of all load components installed must not exceed 400 kg.
Add-on mounting of several XVTLs
• Mounting several XVTLs side-by-side requires M8x20 mm screws. For this
• If two or more XVTLs are mounted side by side, the individual main earthing
purpose, we also offer the XAC connection set for IP40 and the XAC55 for IP55.
points must be electrically connected with each other.
Zusätzlich kann die Verbindungslasche XACC sowie der Verbindungswinkel • If XVTL distribution cabinets rotated by 90° need to be mounted side by side,
XACB verwendet werden.
an XVTL-CF corner frame is available (bottom covers are not included, these
must be ordered separately).
• An IP55 top cover for the corner frame is generally included.
WA_VT09302
Dimensions (mm).
24
Add-On Distribution Boards
XVTL Add-On Distribution Boards - Accessories
XVTL-SO100, XVTL-SO200, XVTL-SO../CF Plinth Panels
XVTL-IC Mounting Plates
•
•
•
•
• Purpose: For the installation of different components
• Material: XVTL-IC 2 mm sheet steel, galvanised
XVTL-IC/S 3 mm sheet steel, galvanised
• Fastening: With XVTL-IC/BRA/SET of fastening brackets
• Weight (kg) XVTL-IC:
For width
425
600
800
1000
1200
Height 1400
–
8,9
–
–
–
Height 1600
4.5
10,5
14.5
18.5
23.4
Height 1800
–
12.1
16.7
21.3
27.0
Height 2000
8,5
13.7
18.9
24.1
30.6
• Weight (kg) XVTL-IC/S:
For width
425
600
800
1000
1200
Height 1400
–
20.5
–
–
–
Height 1600
16.5
23.5
32.5
37.5
46.7
Height 1800
–
26.5
35.5
42.5
52.9
Height 2000
20.5
29.5
38.5
47.5
59.1
Material: 2 mm sheet steel
Phosphatised and polyester-powder-coated
Colour: RAL 7035
Weight (kg):
Height 100 mm
For width/depth
300 400/425 500 600 800 850 1000 1100 1200 1350
2 units XVTL-SO100/S 5.0 5.4
6.2 7.4 9.6
–
–
1 units XVTL-SO100/F –
2.2
–
3.4 4.6
5.8
7.2
Height 200 mm
For width/depth
300 400/425 500 600 800 850 1000 1100 1200 1350
2 units XVTL-SO200/S 7.0 7.6
9.2 10.8 14
–
–
1 units XVTL-SO200/F –
3.2
–
4.4 5.6
6.8
8.2
• Fastening: screw-mounted
• XVTL-SO../CF is a plinth for XVTL-CF corner frames. Two sides of the plinth
are open and two sides are closed by panels.
XVTL-FITUP, XVTL-FITUP/BRA Mounting Aid
• Is used to make the installation of XVTL-IC full-height and pre-equipped
mounting plates in the XVTL easier. With fixing on XVTL-BRA.
• Insertion without screws, removable (aid for panel builders only)
• Material: 2mm sheet steel, galvanised
XVTL-FITUP
VT00803
À
Insert
Á
À
Insert
Á
Â
Remove
Several lengths for several depths of the
XVTL
XVTL-FITUP/BRA
wa_vt01107
Â
Remove
One type for all depths of the XVTL
XVTL-BRA
XVTL-FITUP/BRA
XVTL-IC
XVTL-BRA
BPZ-MPLSASY Mounting Plates
• Material: 2 mm sheet steel, galvanised
• Designed for fixing the SASY 60i
• Can be fixed on XVTL-VP vertical profiles or on XVTL-BRA/IC250 brackets
VT01208
XVTL-VP
BPZ-MPLSASY
XVTL-BRA/IC250
Dimensions (mm).
25
Add-On Distribution Boards
XVTL-BRA/L Brackets
• Material: 2 mm sheet steel, galvanised
• For universal use, adjustable
wa_vt00607
a)
b)
XVTL-HP
XVTL-HP/L
c)
XVTL-...
XVTL-BRA/DIN Brackets (for DIN-rails)
• Material: 2 mm sheet steel, galvanised
• Universal use, mainly for DIN-rail fixing
• Can be fixed on XVTL-VP vertical profiles
wa_vt01407, wa_vt00707
TSA, TSC
XVTL-BRA/DIN
XVTL-HP Horizontal Profiles
• Purpose: These profiles can be screw-mounted in depth and are used for mounting different components, mainly in combination with XVTL-VP vertical profiles
• Material: 2 mm sheet steel, galvanised
• Fastening: Screw-mounting, screws are included in the delivery
• Lengths: 300, 400, 500, 600, 800 mm
XVTL-HP-.-MIB Horizontal Profiles, XVTL-IZM Mounting Plates
XVTL-HP-.-MIB
VT01308
XVTL-IZM
VT01408
• Purpose: For mounting the IZMX16, IZM26, IZM13 or IZM58 (fixed or pull-out design) or other components whose weight, when distributed over at least 2/3 of the supporting surface, must not exceed
150 kg.
• Material: 2 mm sheet steel, galvanised
• Fastening: With 4 screws on the XVTL-HP-.-MIB horizontal profile
• Supporting surface
Width
XVTL-IZM (Width x Depth)
600
510 x 336.5 mm
800
710 x 336.5 mm
1000
910 x 336.5 mm
1200
1110 x 336.5 mm
XVTL-VP Vertical Profiles
• Purpose: Can be screw-mounted vertically in different heights for mounting different components (e.g. mounting plates), mainly used in combination with
XVTL-HP horizontal profiles
• Material: 2.5 mm sheet steel, galvanised
• Fastening: Screw-mounting, screws are included in the delivery
• Lengths: 600, 1000, 1400, 1600, 1800, 2000 mm
26
Add-On Distribution Boards
XSPBA, XVTL-BP Bottom Covers
• Purpose: To close the XVTL add-on distribution board at the bottom and/or
allow cable insertion
• Material: 1.5 mm sheet steel, cellular rubber
• Colour: RAL 7035
• Fastening: Screw-mounting, screws are included in the delivery
• Examples of application
In order to cover the entire depth with cover sheets, you will need the following quantities:
• Weight (kg):
For width
XSPBAC..01
XSPBAC..02
XSPBA
XVTL-BP/JL
a) Blind Covering
b) Cable < Ø 50 mm
VT00908
Depth 300
Depth 400
Depth 500
Depth 600
Depth 800
425
0.4
0.6
0.5
0.4
600
0.5
0.7
0.6
0.7
800
0.6
0.8
0.7
0.9
850
1000
0.7
0.9
0.8
1.2
1100
1200
0.8
1.0
0.9
1.6
1350
VT01008
XSPBAC..01
2
–
2
–
1
XSPBAC..02
1
3
3
5
6
Depth 300
Depth 400
Depth 500
Depth 600
Depth 800
XSPBA
2
2
2
2
2
XSPBAC...01
1
–
–
–
–
XSPBAC..02
–
1
2
3
5
c) Cable Ø 50-80 mm
VT01108
Depth 300
Depth 400
Depth 500
Depth 600
Depth 800
XVTL-BP/JL
1
1
1
1
1
XSPBA
1
1
1
1
1
XSPBAC..01
–
–
–
–
2
XSPBAC..02
–
1
2
3
4
XAR C-Profile Cable Strain Relief Rails
• Fixing of the rail on an XVTL-VP vertical profile
WA_VT07802
• Used for cable strain relief and secure fastening
of cables with clips
• Material: Anchoring rail of galvanised steel
• Rails can be fixed on the XVTL-VP vertical profile
or XVTL-BRA bracket
wa_vt02007
• Fixing of the rail on an XVTL-BRA bracket
Note: Direct fixing of the cable strain relief rail on
the frame is not recommended because of unwanted bending of cables that might occur.
wa_vt02107
XVTL-AB L-Profile Cable Strain Relief Rails
wa_vt10703
• Used for cable strain relief and secure fastening of cables with tie wraps
• Material: Anchoring rail of sheet steel, powder-coated
• Rail can be fixed on an XVTL-VP vertical profile or XVTL-BRA bracket
Note: Direct fixing of the cable strain relief rail on the frame is not recommended because of unwanted
bending of cables that might occur.
Dimensions (mm).
27
Add-On Distribution Boards
XAB4, XVT-SPT6 A4 Pocket for Wiring Diagrams
VT05006
•
•
•
•
Used for keeping wiring diagrams and the like in the distribution cabinet
Size: Suitable for DIN-A4
Material: PVC (XAB4) or sheet steel (XVTL-SPT6)
To be fixed by means of self-adhesive tape or screws
XVTL-DA Door Arrester Set
wa_vt07602
M6
M6
2xM5
2xM6
STOP
XBST... Busbar Supports for the Position at the Top
wa_vt03507
XBST12: In = 1250 A
XBST16: In = 1600 A
XBST20: In = 2000 A
XBST25: In = 2500 A
Icw(1s) = 65 kA
28
Add-On Distribution Boards
Profi+ XVTL-BP-F Mounting frame
Profi+ XVTL-BP-W Built-in Frame for Installation Outgoers
BPZ-FPS Front Plate Support
BPZ-MSW Mounting Side-Panel
•
•
•
•
•
•
These products will enable you to install the Profi+ system
These adapters reduce the width from 425 mm to 400 mm
XVTL-BP-F mounting frame for fixing DIN-rails and mounting plates
XVTL-BP-W built-in frame for installation outgoers, for fixing the BPZ-FPS front plate support and the BPZ-MSW mounting side-panel
The BPZ-MSW mounting side-panel is a swing-out type of panel
Mounting of front plates on the BPZ-FPS front plate support (fixed) or on the BPZ-MSW mounting side-panel (swing-out type)
XVTL-BP-F
XVTL-BP-W
BPZ-MSW
BPZ-FPS
29
Add-On Distribution Boards
Connection System KSX without drilling up to 2500 A
Busbar Support
VT30009
KSX-34P-EXT
•
•
•
•
•
•
•
for outer
for flat busbar 30x10 mm, Double-T and Tripple-T-Profile
3- and 4-pole busbar system
Weight (kg): 4.58
Dimensions (mm): W 300 mm, H 300 mm, D 30 mm
halogen free
Temperature stability up to 130°C
KSX-34P-MID
•
•
•
•
•
•
•
for central
for flat busbar 30x10 mm, Double-T and Tripple-T-Profile
3- and 4-pole busbar system
Weight (kg): 4.58
Dimensions (mm): W 300 mm, H 300 mm, D 30 mm
halogen free
Temperature stability up to 130°C
KSX-3P-MID
•
•
•
•
•
•
•
for central
for Tripple-T-Profile
3-pole busbar system
Weight (kg): 4.58
Dimensions (mm): W 300 mm, H 300 mm, D 30 mm
halogen free
Temperature stability up to 130°C
Busbars CU-BAR according to DIN EN 13601
Tin-plated Cu-bars significantly reduce the work necessary for preparing the contact points.
Cu-busbars are effectively protected against aggressive environments.
Dimension
Double-T
Double-T
Triple-T
Cross-section
500 mm2
720 mm2
1140 mm2
Permissible tolerances:
Radius R 0.3 … 0.7
Width: + 0.1 / – 0.5
Thickness: + 0.1 / – 0.1
Profile Terminals AKP
Current carrying capacity of contact
1600 A
1600 A
1600 A
1600 A
2000 A
2500 A
3000 A
3200 A
Profile
TT
TT
TT
TT
TT
TT
TT
TT
Terminal space W x H (mm)
41 x 20-42
51 x 5-28
51 x 20-42
64 x 5-28
64 x 20-42
81 x 20-42
101 x 20-42
101 x 23-45
Tightning torque (Nm)
40
40
40
40
40
40
40
40
Use spacers provided when two multi-layer Cu-band types of copper busbars are connected in parallel.
30
Type
AKP800
AKP750
AKP1000
AKP900
AKP1200
AKP1600
AKP2000
AKP3600
Add-On Distribution Boards
Universal conductor terminal AKU
Used for connecting conductors featuring cross-sections of 1.5–120 mm2 on busbars 5 or 10 mm thick.
Integrated retaining springs, an open terminal space and captive terminal screws make the installation job easy.
Suitable
Current carrying capaconductors 1)
city of contact point*
1.5–16 mm2 Cu, , , **, 180 A
8 x 6 x 0.5
4–35 mm2 Cu, , , **,
270 A
3/ 6 x 9 x 0.8
16–70 mm2 Cu, , **,
400 A
2x
3 / 6 x 9 x 0.8, 6 x 13 x 0.5
16–120 mm2 Cu, , **,
440 A
4 /6/ 10 x 16 x 0.8
Tightning torque
Nm
4
Terminal space WxH Busbars WxH
mm
mm
7.5 x 7.5
… x 10
Type
AKU16/10
6
10.5 x 11
… x 10
AKU35/10
10
14 x 14
… x 10, TT
AKU70/10
15
17 x 15
… x 10, TT
AKU120/10
* Current carrying capacities specified reflect the thermal capacities of the contact points under favourable conditions (with a maximum
of conductors that can be connected). They do not, however, invalidate the validity of conductor cross-sections and of current carrying
capacities required by any national and international regulations.
** A reduction of maximum conductor cross-sections might be necessary.
Brace terminals AK(S)
For connecting round conductors of 95–300 mm2 and multi-layer copper bars.
The gripper-type of termination technology allows to embrace both sides of the busbar and to connect the conductor without drilling.
Suitable
conductors 1)
95–185 mm2 Cu, Al***
, ,
150–300 mm2 Cu, Al***
, ,
95-300 mm2 Cu, Al***
, ,
Current carrying capacity of contact point *
500 A
Tightning torque
Nm
30
600 A
30
630 A
40
Terminal space WxH Busbars WxH
mm
mm
–
20x5 - 30x10
TTT
–
20x5 - 30x10
TTT
41x25
30x10
TT
*** Connections to aluminium conductors are not maintenance-free
1)
Round conductor, single-wired
Round conductor, fine-wired with expertly pressed wire end ferrule
Round conductor, multi-wired
Sector conductor, single-wired
Sector conductor, multi-wired
Cu-Band
Cu-Bar
Conductor connections
The ratios between conductor cross-sections in mm2 and AWG/MCM-sizes are listed below:
1.5 mm2
16 AWG
2.5 mm2
14 AWG
4 mm2
12 AWG
6 mm2
10 AWG
10 mm2
8 AWG
16 mm2
6 AWG
25 mm2
4 AWG
35 mm2
2 AWG
50 mm2
0 AWG
70 mm2
2/0 AWG
95 mm2
3/0 AWG
120 mm2
250 MCM
150 mm2
300 MCM
185 mm2
350 MCM
240 mm2
500 MCM
300 mm2
600 MCM
Stud-type Terminal AKU-M, clip-on
for connection with cable lug on busbar 10 mm, Double-T and Triple-T-Profile
Max. rated
operating current
490 A
630 A
For cable lug
M8
M10
Available length
mm
8
10
31
Tigntning torque
Nm
marked on terminal
marked on terminal
Type
AKU-M8/10
AKU-M10/10
Type
AKS185
AKS300
AK300
Add-On Distribution Boards
Height
XVTL Dimensions (mm)
100 or 200
Plinth
Plinth
Width
Plinth
Depth
Depth
Detail
Width
A
B
C
D
Height
E
F
G
H
425
600
800
850
1000
1100
1200
1350
263
438
638
688
838
938
1038
1188
345
520
720
770
920
1020
1120
1270
300
475
675
725
875
975
1075
1225
284
459
659
709
859
959
1059
1209
1400
1600
1800
2000
1310
1510
1710
1910
1275
1475
1675
1875
1259
1459
1659
1859
1307
1507
1707
1907
Distance between the holes
Depth
300
400
500
600
800
1)
2)
1)
Depth
275
375
475
575
775
2)
I
223
323
423
523
723
Depth according Ordering Part
Real Depth
J
150
250
350
450
650
K
134
234
334
434
634
L
215
315
415
515
715
P
Height
M
N
O
181
182
382
482
682
1400
1600
1800
2000
350
450
550
500
550
550
500
850
350
450
550
500
Double-wing doors are used as of width 1000.
32
Add-On Distribution Boards
XVTL-CF-./. Corner Frame
For Depth for Depth
Side A
Side B
A
B
C
D
E
400
500
600
800
250
350
450
650
106
106
156
156
31
31
81
81
285
385
485
685
450
550
650
850
400
500
600
800
33
Add-On Distribution Boards
XVTL-D Door
XSDMC Door
Width
B1
B2
B3
C1
C2
Width
B1
B2
B3
C1
C2
425
600
800
850
1000
1100
1200
1350
418
593
793
843
493
543
593
668
497
547
597
672
994
1094
1194
1344
272
447
647
697
347
397
447
522
235
410
610
660
310
360
410
485
425
600
800
850
1000
1000
1100
1200
1350
417
592
792
842
992
492
542
592
667
495
545
595
670
992
1092
1192
1342
264,5
439,5
639,5
689,5
839,5
339,5
389,5
439,5
514,5
210,5
385,5
585,5
635,5
785,5
285,5
335,5
385,5
460,5
Height
A
1400
1600
1800
2000
1340
1540
1740
1940
Height
A
1400
1600
1800
2000
1340
1540
1740
1940
34
Add-On Distribution Boards
Doors with cut-outs prepared for air conditioner
XVTL-D/AC-DTS-8-20
XVTL-D/AC-DTI-8-20
35
Add-On Distribution Boards
Doors with cut-outs prepared for air conditioner
XVTL-D/AC300-.-..
XVTL-D/AC300..-..-L
Width
Height
H1
W1
Width
Height
H1
W1
600
600
600
600
800
800
1400
1600
1800
2000
1600
2000
1340
1540
1740
1940
1540
1740
593
593
593
593
793
793
1000
1000
1000
1200
1200
1200
1600
1800
2000
1600
1800
2000
1540
1740
1940
1540
1740
1940
497
497
497
597
597
597
36
Add-On Distribution Boards
Side Panel with cut-outs prepared for air conditioner
XVTL-MP/S/AC-DTS-./..
XVTL-MP/S/AC300-./..
Width
Height
H1
W1
Width
Height
H1
W1
600
800
2000
2000
1907
1907
482
682
600
600
600
800
1600
1800
2000
2000
1507
1707
1907
1907
482
482
482
682
37
Add-On Distribution Boards
Side Panel with cut-outs prepared for air conditioner
XVTL-MP/S/V-./..
Width
Height
H1
W1
600
600
600
800
1600
1800
2000
2000
1507
1707
1907
1907
482
482
482
682
38
Add-On Distribution Boards
Rear Panel with cut-outs prepared for air conditioner
XVTL-MP/R/AC-DTS-../..
XVTL-MP/R/AC300-../..
Width
Height
H1
W1
Width
Height
H1
W1
600
800
1000
1200
2000
2000
2000
2000
1907
1907
1907
1907
507
707
907
1107
600
600
600
600
800
800
800
1000
1000
1000
1200
1200
1200
1400
1600
1800
2000
1600
1800
2000
1600
1800
2000
1600
1800
2000
1307
1507
1707
1907
1507
1707
1907
1507
1707
1907
1507
1707
1907
507
507
507
507
707
707
707
907
907
907
1107
1107
1107
39
Add-On Distribution Boards
Rear Panel with cut-outs prepared for air conditioner
XVTL-MP/R/V-../..
Width
Height
H1
W1
600
600
600
600
800
800
800
1000
1000
1000
1200
1200
1200
1400
1600
1800
2000
1600
1800
2000
1600
1800
2000
1600
1800
2000
1307
1507
1707
1907
1507
1707
1907
1507
1707
1907
1507
1707
1907
507
507
507
507
707
707
707
907
907
907
1107
1107
1107
40
Add-On Distribution Boards
XVTL-PV Separation Panel (galvanised)
Depth (mm) Height (mm)H (mm)
with
T (mm)
300
400
500
600
800
300
400
500
600
800
300
400
500
600
800
300
400
500
600
800
X
X
X
X
X, Z
X
X
X
X
X, Z
X
X
X
X
X, Z
Y
Y
Y
Y
Y, Z
182
282
382
482
682
182
282
382
482
682
182
282
382
482
682
182
282
382
482
682
2000
1907
1800
1707
1600
1507
1400
1307
41
XSPTF..08
(Depth 800 mm)
XSPTF..06
(Depth 600 mm)
XVTL-MP/T/EF-../5
(Depth 500 mm)
XSPTF..04
(Depth 400 mm)
XVTL-MP/T/EF-../3
(Depth 300 mm)
Add-On Distribution Boards
XVTL-MP/T/EF, XSPTF Top/Bottom Cover
1350 mm
1200 mm
1100 mm
1000 mm
850 mm
800 mm
600 mm
425 mm
42
XSPBM..08
(Depth 800 mm)
XSPBM..06
(Depth 600 mm)
XSPBM..05
(Depth 500 mm)
XSPBM..04
(Depth 400 mm)
XSPBM..03
(Depth 300 mm)
Add-On Distribution Boards
XSPBM Top/Bottom Cover (split)
1350 mm
1200 mm
1100 mm
1000 mm
850 mm
800 mm
600 mm
425 mm
43
Add-On Distribution Boards
XVTL-MP/T/AC../. Top Cover with cut-outs prepared for air conditioners
D
XAD Top Cover
W
Depth
Width
W
D
400
400
400
400
400
400
400
400
500
500
500
500
500
500
500
500
600
600
600
600
600
600
600
600
800
800
800
800
800
800
800
800
400
600
800
850
1000
1100
1200
1350
400
600
800
850
1000
1100
1200
1350
400
600
800
850
1000
1100
1200
1350
400
600
800
850
1000
1100
1200
1350
332
507
707
757
907
1007
1107
1257
332
507
707
757
907
1007
1107
1257
332
507
707
757
907
1007
1107
1257
332
507
707
757
907
1007
1107
1257
282
282
282
282
282
282
282
282
382
382
382
382
382
382
382
382
482
482
482
482
482
482
482
482
682
682
682
582
682
582
682
582
Type
XVTL-TG-400/16/4-IVS
XVTL-TG-400/20/4-IVS
XVTL-TG-600/16/4-IVS
XVTL-TG-600/20/4-IVS
XVTL-TG-800/16/4-IVS
XVTL-TG-800/20/4-IVS
XVTL-TG-1200/16/4-IVS
XVTL-TG-1200/20/4-IVS
Depth
Width
W
D
600
600
600
800
800
800
800
1000
1200
800
1000
1200
707
907
1107
707
907
1107
482
482
482
682
682
682
Support Rack XVTL-TG for XVTL…-IVS
B
397
397
597
597
797
797
1197
1197
H
1540
1870
1540
1870
1540
1870
1540
1870
44
Add-On Distribution Boards
XVTL-SO, XVTL.SO../CF Plinth
XSFDR Green/Blue Design Strip
45
Depth
A
300
400
500
600
800
265
365
465
565
765
Add-On Distribution Boards
XVTL-IC... Mounting Plates
XVTL-IC
(2 mm sheet steel)
XVTL-IC/S
(3 mm sheet steel)
BPZ-MPLSASY Mounting Plate
Width
A
B
425
600
800
1000
1200
313
488
688
888
1088
300.5
475.5
675.5
875.5
1075.5
46
Width
A
B
C
425
600
800
1000
1200
339
514
714
914
1114
315
490
690
890
1090
275
450
650
850
1050
Depth
D
1400
1600
1800
2000
1249
1449
1649
1849
Add-On Distribution Boards
XVTL-BRA/M Brackets
XVTL-BRA Brackets
Layout left
Layout right
XVTL-BRA/L Brackets
XVTL-BRA/IC250 Brackets
For direct fixing of SASY 60i supports - when using BPZ-MPLSASY
47
Add-On Distribution Boards
XVTL-BRA/DIN Brackets
XVTL-HP Horizontal Profiles
Depth 300 mm
Depth 400 mm
Depth 500 mm
Depth 600 mm
Depth 800 mm
48
Add-On Distribution Boards
XVTL-HP/L Horizontal Profile
Dimensions (mm)
300 mm
400 mm
500 mm
600 mm
800 mm
XVTL-IZM Mounting Plate for IZM
W
Width
W (mm)
600
800
1000
1200
510
710
910
1110
49
a
165
265
365
465
665
b
120
220
320
420
620
Add-On Distribution Boards
XVTL-VP Vertical Profiles
Height 600 mm
Height 1000 mm
Height 1400 mm
Height 1600 mm
Height 1800 mm
Height 2000 mm
XSPBA, XVTL-BP Bottom Covers
XSPBAC..01, XSPBAC..02
Dimensions (mm)
Width
a
b
425
600
800
850
1000
1100
1200
1350
300
475
675
725
875
975
1075
1225
325
500
700
750
900
1000
1100
1250
c
XSPBAC..01
35
35
35
35
35
35
35
35
c
XSPBAC..02
110
110
110
110
110
110
110
110
XVTL-BP/JL
XVTL-BP/JL
XSPBA
XSPBAC..01
XSPBAC..02
50
Add-On Distribution Boards
XAR Cable Strain Relief Rails - C-Profile
Dimensions (mm)
a
320
520
720
770
920
1170
425
600
800
850
1000
1200
b
290
490
690
c
240
440
640
890
1140
840
1090
XVTL-AB Cable Strain Relief Rails - L-profile
Width
a
425
600
800
1000
1200
330
505
705
905
1105
XVTL-DA Door Arrester Set
51
Add-On Distribution Boards
F3A Insertion Flanges for IP55 Degree of Protection
• Purpose: Plastic insertion flange for environments requiring a high degree of protection, can be mounted instead of a blind plate
• Dimensions 330x200 mm
VT17407
VT09208
VT17507
VT17307
F3A-0
Blind flange
F3A-XP
Blind flange sheet steel
F3A-4
4xM16, 6xM25/16, 8xM32/20
F3A-8
2xM20, 8xM25/16, 4xM32/20,
1xM50/32
VT17607
VT17707
VT17807
VT17207
F3A-12
2xM16, 12xM20, 2xM40/25, 2xM50/32
F3A-34
24xM16, 13xM20
F3A-KTD
2 grommets for cables
up to Ø 70 mm
F3A-D
Cellular rubber pass-through flange,
40 cables of Ø 10-13 mm,
4 cables of Ø 17-21 mm,
2 cables of Ø 27-30 mm
CU-BAR-500/T
CU-BAR-720/T
CU-BAR-1140/T
52
Add-On Distribution Boards
AKU 16/10
AKU 35/10
AKU 70/10
AKU 120/10
AKS185
AKS300
53