Data Sheet
HA1630S04/05/06 Series
Ultra-Small Low Voltage Operation CMOS Single
Operational Amplifier
R03DS0082EJ0200
Rev.2.00
Jan 10, 2014
Description
The HA1630S04/05/06 are high slew rate single CMOS Operational Amplifiers realizing low voltage operation, low
input offset voltage and low supply current. In addition to a low operating voltage from 1.8V, these device output can
achieve full swing output voltage capability extending to either supply. Available in an ultra-small CMPAK-5 package
that occupies only 1/8 the area of the SOP-8 package.
Features
• Low power and single supply operation
• Low input offset voltage
• Low supply current
• High slew rate
• Maximum output voltage
• Low input bias current
VDD = 1.8 to 5.5 V
VIO = 4.0 mV Max
IDD = 200 μA Typ (HA1630S04)
IDD = 400 μA Typ (HA1630S05)
IDD = 800 μA Typ (HA1630S06)
SR = 2 V/μs Typ (HA1630S04)
SR = 4 V/μs Typ (HA1630S05)
SR = 8 V/μs Typ (HA1630S06)
VOH = 2.9 V Min (at VDD = 3.0 V)
IIB = 1 pA Typ
Ordering Information
Type No.
HA1630S04CM
HA1630S04LP
HA1630S05CM
HA1630S05LP
HA1630S06CM
HA1630S06LP
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Package Name
CMPAK-5
MPAK-5
CMPAK-5
MPAK-5
CMPAK-5
MPAK-5
Package Code
PTSP0005ZC-A
PLSP0005ZB-A
PTSP0005ZC-A
PLSP0005ZB-A
PTSP0005ZC-A
PLSP0005ZB-A
Page 1 of 24
HA1630S04/05/06 Series
Pin Arrangement
VDD
5
VOUT
4
+ −
1
2
3
VIN(+) VSS VIN(–)
Equivalent Circuit
VDD
VIN(–)
VOUT
VIN(+)
VSS
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 2 of 24
HA1630S04/05/06 Series
Absolute Maximum Ratings
(Ta = 25°C)
Items
Supply voltage
Differential input voltage
Input voltage
Power dissipation
Operating temp. Range
Storage temp. Range
Note:
Symbol
Ratings
7
–VDD to +VDD
–0.3 to +VDD
200
–40 to +85
–55 to +125
VDD
VIN(diff)
VIN
PT
Topr
Tstg
Unit
V
V
V
mW
°C
°C
Note
1
1. Do not apply Input Voltage exceeding VDD or 7 V.
Electrical Characteristics
(VDD = 3.0 V, Ta = 25°C)
Items
Input offset voltage
Input offset current
Input bias current
Symbol
VIO
IIO
IIB
Min
—
—
—
Typ
—
(1.0)
(1.0)
Max
4.0
—
—
Unit
mV
pA
pA
Output high voltage
Output source current
VOH
IO SOURCE
2.9
100
—
200
—
—
V
μA
200
400
—
—
—
—
–0.05 to 2.1
0 to 1.9
—
—
—
60
—
—
—
50
50
—
—
400
800
—
(5.0)
(6.0)
(6.5)
—
—
(2.0)
(4.0)
(8.0)
90
(2.1)
(3.3)
(3.6)
70
70
200
400
—
—
0.1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
400
800
—
800
1700
Output low voltage
Output sink current
VOL
IO SINK
Common mode input voltage
range
VCM
Slew rate
SR
Voltage gain
Gain bandwidth product
AV
BW
Power supply rejection ratio
Common mode rejection ratio
Supply current
PSRR
CMRR
IDD
V
mA
V
V/μs
dB
MHz
dB
dB
μA
Test Condition
Vin = 1.5 V
Vin = 1.5 V
Vin = 1.5 V
RL = 100 kΩ
VOH = 2.5 V (HA1630S04)
VOH = 2.5 V (HA1630S05)
VOH = 2.5 V (HA1630S06)
RL = 100 kΩ
VOL = 0.5 V (HA1630S04)
VOL = 0.5 V (HA1630S05)
VOL = 0.5 V (HA1630S06)
(HA1630S04, HA1630S05)
(HA1630S06)
CL = 20 pF (HA1630S04)
CL = 20 pF (HA1630S05)
CL = 20 pF (HA1630S06)
CL = 20 pF (HA1630S04)
CL = 20 pF (HA1630S05)
CL = 20 pF (HA1630S06)
RL = ∞ (HA1630S04)
RL = ∞ (HA1630S05)
RL = ∞ (HA1630S06)
Notes: 1. In the case of continuous current flow, use a sink current of under 4 mA.
2. ( ) : Design specification
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 3 of 24
HA1630S04/05/06 Series
Table of Graphs
Electrical Characteristics
Supply current
IDD
vs Supply voltage
vs Ambient temperature
Output high voltage
VOH
vs Output source current
vs Supply voltage
Output source current
IO SOURCE
vs Ambient temperature
Output low voltage
VOL
vs Output sink current
Output sink current
IO SINK
vs Ambient temperature
Input offset voltage
VIO
Distribution
vs Supply voltage
vs Ambient temperature
vs Ambient temperature
VCM
Common mode input
voltage range
HA1630S04
Figure
HA1630S05
Figure
HA1630S06
Figure
1-1
1-2
1-3
1-4
1-5
1-6
1-7
1-8
1-9
1-10
1-11
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
3-9
3-10
3-11
Test
Circuit
2
4
6
5
6
1
7
Power supply rejection
ratio
PSRR
vs Frequency
1-12
2-12
3-12
1
Common mode rejection
ratio
CMRR
vs Frequency
1-13
2-13
3-13
7
Voltage gain & phase
angle
Input bias current
AV
vs Frequency
1-14
2-14
3-14
10
IIB
SRr
SRf
1-15
1-16
1-17
1-18
2-15
2-16
2-17
2-18
3-15
3-16
3-17
3-18
3
Slew Rate (rising)
Slew Rate (falling)
Slew rate
vs Ambient temperature
vs Input voltage
vs Ambient temperature
vs Ambient temperature
Large signal transient
response
1-19
2-19
3-19
Small signal transient
response
1-20
2-20
3-20
vs. Output voltage p-p
vs. Output voltage p-p
1-21
1-22
2-21
2-22
3-21
3-22
vs Frequency
1-23
2-23
3-23
vs Frequency
1-24
2-24
3-24
Total harmonic distortion +
noise
(0 dB)
(40 dB)
Maximum p-p output
voltage
Voltage noise density
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
9
8
Page 4 of 24
HA1630S04/05/06 Series
Main Characteristics (HA1630S04)
Figure 1-1. HA1630S04
Supply Current vs. Supply Voltage
400
Ta = 25°C
Supply Current IDD (μA)
Supply Current IDD (μA)
400
Figure 1-2. HA1630S04
Supply Current vs. Ambient Temperature
300
200
100
0
1
2
3
4
5
Supply Voltage VDD (V)
VDD = 5.5 V
VDD = 3.0 V
300
VDD = 1.8 V
200
100
0
−40
6
5 VDD = 5.5 V
4
3
VDD = 3.0 V
2
VDD = 1.8 V
1
Output High Voltage VOH (V)
Output High Voltage VOH (V)
Ta = 25°C
100
Figure 1-4. HA1630S04
Output High Voltage vs. Supply Voltage
Figure 1-3. HA1630S04
Output High Voltage vs. Output Source Current
6
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
6
Ta = 25°C
VDD = 3.0 V
RL = 100 kΩ
5
4
3
2
1
0
0
100
200
300
Output Source Current IOSOURCE (μA)
1
2
3
4
5
Supply Voltage VDD (V)
6
Output Source Current
IOSOURCE (μA)
Figure 1-5. HA1630S04
Output Source Current vs. Ambient Temperature
400
300
VDD = 5.5 V
VDD = 3.0 V
VDD = 1.8 V
200
100
0
−40
−20
0
20
40
60
80
100
Ambient Temperature Ta (°C)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 5 of 24
HA1630S04/05/06 Series
Figure 1-7. HA1630S04
Output Sink Current vs. Ambient Temperature
10
1.5
VDD = 5.5 V
Output Sink Current
IOSINK (mA)
Output Low Voltage VOL (V)
Figure 1-6. HA1630S04
Output Low Voltage vs. Output Sink Current
VDD = 3.0 V
1.0
VDD = 1.8 V
0.5
0
0
2
4
Output Sink Current IOSINK (mA)
VDD = 5.5 V
VDD = 3.0 V
8
VDD = 1.8 V
6
4
2
0
−40
6
Percentage (%)
40
Ta = 25°C
VDD = 3.0 V
30
20
10
0
−4
−3 −2 −1 0
1
2
3
Input Offset Voltage VIO (mV)
4
4
Ta = 25°C
VIN = 0.5 V
3
2
1
0
−1
−2
−3
−4
1
2
Common Mode
Input Voltage VCM (V)
Input Offset Voltage VIO (mV)
6
3.0
4
VDD = 1.8 V, VIN = 0.9 V
2
VDD = 3.0 V, VIN = 1.5 V
1
0
−1
VDD = 5.5 V, VIN = 2.75 V
−2
−3
−4
−40
3
4
5
Supply Voltage VDD (V)
Figure 1-11. HA1630S04
Common Mode Input Voltage vs.
Ambient Temperature
Figure 1-10. HA1630S04
Input Offset Voltage vs. Ambient Temperature
3
100
Figure 1-9. HA1630S04
Input Offset Voltage vs. Supply Voltage
Input Offset Voltage VIO (mV)
Figure 1-8. HA1630S04
Input Offset Voltage Distribution
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
100
2.0
VDD = 3.0 V
1.0
0
−1.0
−40
−20
0
20
40
60
80
100
Ambient Temperature Ta (°C)
Page 6 of 24
HA1630S04/05/06 Series
Power Supply Rejection Ratio
PSRR (dB)
Figure 1-12. HA1630S04
Power Supply Rejection Ratio vs. Frequency
100
Ta = 25°C
VDD = 3.0 V
RL = 1 MΩ
CL = 20 pF
80
60
40
20
0
10
100
1k
10k
100k
1M
10M
Frequency f (Hz)
Common Mode Rejection Ratio
CMRR (dB)
Figure 1-13. HA1630S04
Common Mode Rejection Ratio vs. Frequency
100
Ta = 25°C
VDD = 3.0 V
RL = 1 MΩ
CL = 20 pF
80
60
40
20
0
10
100
1k
10k
100k
1M
10M
Frequency f (Hz)
Figure 1-14. HA1630S04
Open Loop Voltage Gain and Phase Angle vs. Frequency
Open Loop Voltage Gain
AVOL (dB)
80
Ta = 25°C
VDD = 3.0 V
RL = 1 MΩ
CL = 20 pF
Open Loop Voltage Gain
60
135
90
40
Phase Angle
20
45
0
Phase Margin: 57 deg
0
−45
−20
−40
10
180
Phase Angle (deg)
225
100
100
1k
10k
100k
1M
−90
10M
Frequency f (Hz)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 7 of 24
HA1630S04/05/06 Series
200
VDD = 3.0 V
100
0
−100
−200
0
Figure 1-16. HA1630S04
Input Bias Current vs. Input Voltage
Input Bias Current IIB (pA)
Input Bias Current IIB (pA)
Figure 1-15. HA1630S04
Input Bias Current vs. Ambient Temperature
25
50
75
Ambient Temperature Ta (°C)
200
100
0
−100
−200
100
Figure 1-17. HA1630S04
Slew Rate (rising) vs. Ambient Temperature
Slew Rate SRf (V/μs)
Slew Rate SRr (V/μs)
0.5
1.0
1.5
2.0
Input Voltage VIN (V)
2.5
3.0
5
VDD = 5.5 V
4
VDD = 3.0 V
VDD = 1.8 V
2
1
0
−40
0
Figure 1-18. HA1630S04
Slew Rate (falling) vs. Ambient Temperature
5
3
Ta = 25°C
VDD = 3.0 V
−20
0
20
40
60
80
100
VDD = 5.5 V
VDD = 3.0 V
VDD = 1.8 V
4
3
2
1
0
−40
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
Ambient Temperature Ta (°C)
Figure 1-19. HA1630S04
Large Signal Transient Response
Figure 1-20. HA1630S04
Small Signal Transient Response
2.0 V
Vin = 2.1 Vp-p, 250 kHz
Ta = 25°C
VDD = 3.0 V
RL = 100 kΩ
CL = 20 pF
1.6 V
Vin = 0.2 Vp-p, 250 kHz
0V
1.4 V
2.0 V
1.6 V
0V
1.4 V
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
100
Ta = 25°C
VDD = 3.0 V
RL = 100 kΩ
CL = 20 pF
Page 8 of 24
HA1630S04/05/06 Series
Figure 1-21. HA1630S04
Total Harmonic Distortion + Noise vs.
Output Voltage p-p
10
VDD = 3.0 V
Ta = 25°C
Gain = 0 dB
1
T.H.D. + Noise (%)
T.H.D. + Noise (%)
10
Figure 1-22. HA1630S04
Total Harmonic Distortion + Noise vs.
Output Voltage p-p
f = 10 kHz
f = 1 kHz
f = 100 Hz
0.1
0.01
0.001
1
f = 10 kHz
f = 1 kHz
f = 100 Hz
0.1
0.01 V = 3.0 V
DD
Ta = 25°C
Gain = 40 dB
0.001
0
0.5
1.0
1.5
2.0
2.5
3.0
0
Output Voltage Vout p-p (V)
0.5
1.0
1.5
2.0
2.5
3.0
Output Voltage Vout p-p (V)
Voltage Output Vout p-p (V)
Figure 1-23. HA1630S04
Voltage Output p-p vs. Frequency
3.5
Ta = 25°C
VDD = 3.0 V
3.0
2.5
Gain = 40 dB,
VIN = 0.03 Vp-p
2.0
Gain = 0 dB,
VIN = 2.0 Vp-p
1.5
1.0
0.5
0
1k
Voltage Noise Density (nVms/√Hz)
Gain = 20 dB,
VIN = 0.3 Vp-p
10k
100k
Frequency f (Hz)
1M
10M
Figure 1-24. HA1630S04
Voltage Noise Density vs. Frequency
200
VDD = 3.0 V
Ta = 25°C
Gain = 40 dB
RS = 1 kΩ
160
120
80
40
0
100
1k
10k
Frequency f (Hz)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 9 of 24
HA1630S04/05/06 Series
Main Characteristics (HA1630S05)
Figure 2-1. HA1630S05
Supply Current vs. Supply Voltage
Figure 2-2. HA1630S05
Supply Current vs. Ambient Temperature
800
Ta = 25°C
Supply Current IDD (μA)
Supply Current IDD (μA)
800
600
400
200
0
1
2
3
4
5
Supply Voltage VDD (V)
VDD = 5.5 V
VDD = 3.0 V
600
VDD = 1.8 V
400
200
0
−40
6
6
Ta = 25°C
VDD = 5.5 V
5
4
3
VDD = 3.0 V
2
VDD = 1.8 V
1
0
100
Figure 2-4. HA1630S05
Output High Voltage vs. Supply Voltage
Output High Voltage VOH (V)
Output High Voltage VOH (V)
Figure 2-3. HA1630S05
Output High Voltage vs. Output Source Current
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
6
Ta = 25°C
VDD = 3.0 V
5
4
RL = 100 kΩ
RL = 20 kΩ
3
2
1
0
100
200
300
400
500
Output Source Current IOSOURCE (μA)
1
2
3
4
5
Supply Voltage VDD (V)
6
Output Source Current
IOSOURCE (μA)
Figure 2-5. HA1630S05
Output Source Current vs. Ambient Temperature
800
VDD = 5.5 V
VDD = 3.0 V
600
VDD = 1.8 V
400
200
0
−40
−20
0
20
40
60
80
100
Ambient Temperature Ta (°C)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 10 of 24
HA1630S04/05/06 Series
Figure 2-7. HA1630S05
Output Sink Current vs. Ambient Temperature
10
1.5
Output Sink Current
IOSINK (mA)
Output Low Voltage VOL (V)
Figure 2-6. HA1630S05
Output Low Voltage vs. Output Sink Current
VDD = 5.5 V
VDD = 3.0 V
1.0
VDD = 1.8 V
0.5
0
0
2
4
6
Output Sink Current IOSINK (mA)
VDD = 5.5 V
VDD = 3.0 V
8
VDD = 1.8 V
6
4
2
0
−40
8
Percentage (%)
40
Ta = 25°C
VDD = 3.0 V
30
20
10
0
−4
−3 −2 −1
0
1
2
3
Input Offset Voltage VIO (mV)
4
4
Ta = 25°C
VIN = 0.5 V
3
2
1
0
−1
−2
−3
−4
1
2
Common Mode
Input Voltage VCM (V)
Input Offset Voltage VIO (mV)
6
3.0
4
VDD = 1.8 V, VIN = 0.5 V
2
VDD = 3.0 V, VIN = 1.5 V
1
0
−1
VDD = 5.5 V, VIN = 2.75 V
−2
−3
−4
−40
3
4
5
Supply Voltage VDD (V)
Figure 2-11. HA1630S05
Common Mode Input Voltage vs.
Ambient Temperature
Figure 2-10. HA1630S05
Input Offset Voltage vs. Ambient Temperature
3
100
Figure 2-9. HA1630S05
Input Offset Voltage vs. Supply Voltage
Input Offset Voltage VIO (mV)
Figure 2-8. HA1630S05
Input Offset Voltage Distribution
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
100
2.0
VDD = 3.0 V
1.0
0
−1.0
−40
−20
0
20
40
60
80
100
Ambient Temperature Ta (°C)
Page 11 of 24
HA1630S04/05/06 Series
Power Supply Rejection Ratio
PSRR (dB)
Figure 2-12. HA1630S05
Power Supply Rejection Ratio vs. Frequency
100
Ta = 25°C
VDD = 3.0 V
RL = 1 MΩ
CL = 20 pF
80
60
40
20
0
10
100
1k
10k
100k
1M
10M
Frequency f (Hz)
Common Mode Rejection Ratio
CMRR (dB)
Figure 2-13. HA1630S05
Common Mode Rejection Ratio vs. Frequency
100
Ta = 25°C
VDD = 3.0 V
RL = 1 MΩ
CL = 20 pF
80
60
40
20
0
10
100
1k
10k
100k
1M
10M
Frequency f (Hz)
Figure 2-14. HA1630S05
Open Loop Voltage Gain and Phase Angle vs. Frequency
Open Loop Voltage Gain
AVOL (dB)
Ta = 25°C
VDD = 3.0 V
RL = 1 MΩ
CL = 20 pF
Open Loop Voltage Gain
80
60
135
90
40
20
45
Phase Angle
0
0
Phase Margin: 55 deg
−45
−20
−40
10
180
Phase Angle (deg)
225
100
100
1k
10k
100k
1M
−90
10M
Frequency f (Hz)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 12 of 24
HA1630S04/05/06 Series
200
VDD = 3.0 V
100
0
−100
−200
0
Figure 2-16. HA1630S05
Input Bias Current vs. Input Voltage
Input Bias Current IIB (pA)
Input Bias Current IIB (pA)
Figure 2-15. HA1630S05
Input Bias Current vs. Ambient Temperature
25
50
75
Ambient Temperature Ta (°C)
200
Ta = 25°C
VDD = 3.0 V
100
0
−100
−200
100
0
Figure 2-17. HA1630S05
Slew Rate (rising) vs. Ambient Temperature
VDD = 5.5 V
Slew Rate SRf (V/μs)
Slew Rate SRr (V/μs)
2.5
3.0
10
8
VDD = 3.0 V
VDD = 1.8 V
4
2
0
−40
1.0
1.5
2.0
Input Voltage VIN (V)
Figure 2-18. HA1630S05
Slew Rate (falling) vs. Ambient Temperature
10
6
0.5
−20
0
20
40
60
80
100
VDD = 5.5 V
8
6
VDD = 3.0 V
VDD = 1.8 V
4
2
0
−40
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
Ambient Temperature Ta (°C)
Figure 2-19. HA1630S05
Large Signal Transient Response
Figure 2-20. HA1630S05
Small Signal Transient Response
2.0 V
VIN = 2.1 Vp-p, 500 kHz
Ta = 25°C
VDD = 3.0 V
RL = 100 kΩ
CL = 20 pF
1.6 V
VIN = 0.2 Vp-p, 500 kHz
0V
1.4 V
2.0 V
1.6 V
0V
1.4 V
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
100
Ta = 25°C
VDD = 3.0 V
RL = 100 kΩ
CL = 20 pF
Page 13 of 24
HA1630S04/05/06 Series
Figure 2-21. HA1630S05
Total Harmonic Distortion + Noise vs.
Output Voltage p-p
10
VDD = 3.0 V
Ta = 25°C
Gain = 0 dB
1
T.H.D. + Noise (%)
T.H.D. + Noise (%)
10
Figure 2-22. HA1630S05
Total Harmonic Distortion + Noise vs.
Output Voltage p-p
f = 10 kHz
f = 1 kHz
f = 100 Hz
0.1
0.01
0.001
0.1
0.01
0.001
0
0.5
1.0
1.5
2.0
2.5
3.0
f = 10 kHz
f = 1 kHz
f = 100 Hz
1
VDD = 3.0 V
Ta = 25°C
Gain = 40 dB
0
Output Voltage Vout p-p (V)
0.5
1.0
1.5
2.0
2.5
3.0
Output Voltage Vout p-p (V)
Voltage Output Vout p-p (V)
Figure 2-23. HA1630S05
Voltage Output p-p vs. Frequency
3.5
Ta = 25°C
VDD = 3.0 V
3.0
Gain = 40 dB,
VIN = 0.03 Vp-p
2.5
Gain = 20 dB,
VIN = 0.3 Vp-p
2.0
Gain = 0 dB,
VIN = 2.0 Vp-p
1.5
1.0
0.5
0
1k
10k
100k
Frequency f (Hz)
1M
10M
Figure 2-24. HA1630S05
Voltage Noise Density vs. Frequency
Voltage Noise Density
(nVms/√Hz)
200
VDD = 3.0 V
Ta = 25°C
Gain = 40 dB
RS = 1 kΩ
160
120
80
40
0
100
1k
10k
Frequency f (Hz)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 14 of 24
HA1630S04/05/06 Series
Main Characteristics (HA1630S06)
Figure 3-1. HA1630S06
Supply Current vs. Supply Voltage
1600
Ta = 25°C
Supply Current IDD (μA)
Supply Current IDD (μA)
1600
Figure 3-2. HA1630S06
Supply Current vs. Ambient Temperature
1200
800
400
0
1
2
3
4
5
Supply Voltage VDD (V)
VDD = 5.5 V
VDD = 3.0 V
1200
VDD = 1.8 V
800
400
0
−40
6
6
Ta = 25°C
5 VDD = 5.5 V
4
VDD = 3.0 V
3
VDD = 1.8 V
2
1
0
100
Figure 3-4. HA1630S06
Output High Voltage vs. Supply Voltage
Output High Voltage VOH (V)
Output High Voltage VOH (V)
Figure 3-3. HA1630S06
Output High Voltage vs. Output Source Current
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
6
Ta = 25°C
VDD = 3.0 V
5
RL = 100 kΩ
RL = 20 kΩ
4
3
2
1
0
200
400
600
800
1000
Output Source Current IOSOURCE (μA)
1
2
3
4
5
Supply Voltage VDD (V)
6
Output Source Current
IOSOURCE (μA)
Figure 3-5. HA1630S06
Output Source Current vs. Ambient Temperature
1600
VDD = 5.5 V
VDD = 3.0 V
1200
VDD = 1.8 V
800
400
0
−40
−20
0
20
40
60
80
100
Ambient Temperature Ta (°C)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 15 of 24
HA1630S04/05/06 Series
Figure 3-7. HA1630S06
Output Sink Current vs. Ambient Temperature
12
1.5
Output Sink Current
IOSINK (mA)
Output Low Voltage VOL (V)
Figure 3-6. HA1630S06
Output Low Voltage vs. Output Sink Current
VDD = 5.5 V
VDD = 3.0 V
1.0
VDD = 1.8 V
0.5
VDD = 5.5 V
10
8
VDD = 3.0 V
6
4
VDD = 1.8 V
2
0
0
2
4
6
8
Output Sink Current IOSINK (mA)
0
−40
10
Percentage (%)
40
Ta = 25°C
VDD = 3.0 V
30
20
10
0
−4
−3 −2 −1
0
1
2
3
Input Offset Voltage VIO (mV)
4
4
Ta = 25°C
VIN = 0.5 V
3
2
1
0
−1
−2
−3
−4
1
2
Common Mode
Input Voltage VCM (V)
Input Offset Voltage VIO (mV)
6
3.0
4
VDD = 1.8 V, VIN = 0.5 V
2
VDD = 3.0 V, VIN = 1.5 V
1
0
−1
VDD = 5.5 V, VIN = 2.75 V
−2
−3
−4
−40
3
4
5
Supply Voltage VDD (V)
Figure 3-11. HA1630S06
Common Mode Input Voltage vs.
Ambient Temperature
Figure 3-10. HA1630S06
Input Offset Voltage vs. Ambient Temperature
3
100
Figure 3-9. HA1630S06
Input Offset Voltage vs. Supply Voltage
Input Offset Voltage VIO (mV)
Figure 3-8. HA1630S06
Input Offset Voltage Distribution
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
100
2.0
VDD = 3.0 V
1.0
0
−1.0
−40
−20
0
20
40
60
80
100
Ambient Temperature Ta (°C)
Page 16 of 24
HA1630S04/05/06 Series
Power Supply Rejection Ratio
PSRR (dB)
Figure 3-12. HA1630S06
Power Supply Rejection Ratio vs. Frequency
100
Ta = 25°C
VDD = 3.0 V
RL = 1 MΩ
CL = 20 pF
VRIP = 0.1 Vp
80
60
40
20
0
10
100
1k
10k
100k
1M
10M
Frequency f (Hz)
Common Mode Rejection Ratio
CMRR (dB)
Figure 3-13. HA1630S06
Common Mode Rejection Ratio vs. Frequency
100
Ta = 25°C
VDD = 3.0 V
RL = 1 MΩ
CL = 20 pF
80
60
40
20
0
10
100
1k
10k
100k
1M
10M
Frequency f (Hz)
Figure 3-14. HA1630S06
Open Loop Voltage Gain and Phase Angle vs. Frequency
Open Loop Voltage Gain
AVOL (dB)
Ta = 25°C
VDD = 3.0 V 180
RL = 1 MΩ
CL = 20 pF 135
Open Loop Voltage Gain
80
60
90
40
Phase Angle
45
20
0
Phase Margin: 65 deg
−45
−20
−40
10
0
Phase Angle (deg)
225
100
100
1k
10k
100k
1M
−90
10M
Frequency f (Hz)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 17 of 24
HA1630S04/05/06 Series
200
VDD = 3.0 V
100
0
−100
−200
0
25
50
75
Ambient Temperature Ta (°C)
Figure 3-16. HA1630S06
Input Bias Current vs. Input Voltage
Input Bias Current IIB (pA)
Input Bias Current IIB (pA)
Figure 3-15. HA1630S06
Input Bias Current vs. Ambient Temperature
200
100
0
−100
−200
100
Figure 3-17. HA1630S06
Slew Rate (rising) vs. Ambient Temperature
0.5
1.0
1.5
2.0
Input Voltage VIN (V)
2.5
3.0
14
12
Slew Rate SRf (V/μs)
Slew Rate SRr (V/μs)
0
Figure 3-18. HA1630S06
Slew Rate (falling) vs. Ambient Temperature
14
VDD = 5.5 V
VDD = 3.0 V
10
VDD = 1.8 V
8
6
4
−40
Ta = 25°C
VDD = 3.0 V
−20
0
20
40
60
80
100
VDD = 5.5 V
12
10
VDD = 3.0 V
VDD = 1.8 V
8
6
4
−40
−20
0
20
40
60
80
Ambient Temperature Ta (°C)
Ambient Temperature Ta (°C)
Figure 3-19. HA1630S06
Large Signal Transient Response
Figure 3-20. HA1630S06
Small Signal Transient Response
2.0 V
VIN = 1.9 Vp-p, 500 kHz
Ta = 25°C
VDD = 3.0 V
RL = 100 kΩ
CL = 20 pF
1.6 V
VIN = 0.2 Vp-p, 500 kHz
0V
1.4 V
2.0 V
1.6 V
0V
1.4 V
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
100
Ta = 25°C
VDD = 3.0 V
RL = 100 kΩ
CL = 20 pF
Page 18 of 24
HA1630S04/05/06 Series
Figure 3-21. HA1630S06
Total Harmonic Distortion + Noise vs.
Output Voltage p-p
10
VDD = 3.0 V
Ta = 25°C
Gain = 0 dB
1
T.H.D. + Noise (%)
T.H.D. + Noise (%)
10
Figure 3-22. HA1630S06
Total Harmonic Distortion + Noise vs.
Output Voltage p-p
f = 10 kHz
f = 1 kHz
f = 100 Hz
0.1
0.01
1
f = 10 kHz
f = 1 kHz
f = 100 Hz
0.1
0.01 VDD = 3.0 V
Ta = 25°C
Gain = 40 dB
0.001
0.001
0
0.5
1.0
1.5
2.0
2.5
3.0
0
Output Voltage Vout p-p (V)
0.5
1.0
1.5
2.0
2.5
3.0
Output Voltage Vout p-p (V)
Voltage Output Vout p-p (V)
Figure 3-23. HA1630S06
Voltage Output p-p vs. Frequency
3.5
Ta = 25°C
VDD = 3.0 V
3.0
2.5
Gain = 40 dB,
VIN = 0.03 Vp-p
Gain = 20 dB,
VIN = 0.3 Vp-p
10k
100k
Frequency f (Hz)
Gain = 0 dB,
VIN = 2.0 Vp-p
2.0
1.5
1.0
0.5
0
1k
1M
10M
Figure 3-24. HA1630S06
Voltage Noise Density vs. Frequency
Voltage Noise Density
(nVms/√Hz)
200
VDD = 3.0 V
Ta = 25°C
Gain = 40 dB
RS = 1 kΩ
160
120
80
40
0
100
1k
10k
Frequency f (Hz)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 19 of 24
HA1630S04/05/06 Series
Test Circuits
1. Power Supply Rejection Ratio, PSRP & Voltage Offset, VIO
VIO
VDD
VIO = VO −
RF = 680 kΩ
VDD
2
×
RS
R S + RF
RS = 6.8 kΩ
−
+
PSRR
VO
RS = 6.8 kΩ
VDD
PSRR = −20log
2
VDD1 − VDD2
VO1 − VO2
×
RS
R S + RF
Measure VO corresponding to VDD1 = 2.95 V and VDD2 = 3.05 V
2. Supply Current, IDD
3. Input Bias Current, IIB
VDD
VDD
A
−
+
−
+
VDD
VDD
2
2
A
4. Output High Voltage, VOH
VOH
VDD
−
+
VIN1
VIN2
VIN1 = VDD / 2 − 0.05 V
VIN2 = VDD / 2 + 0.05 V
VO
RL = 100 kΩ
5. Output Low Voltage, VOL
VOL
VDD
VIN1 = VDD / 2 + 0.05 V
VIN2 = VDD / 2 − 0.05 V
−
+
VIN1
RL = 100 kΩ
VO
VIN2
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 20 of 24
HA1630S04/05/06 Series
6. Output Source Current, IOSOURCE & Output Sink Current, IOSINK
VDD
IOSOURCE
VO = VDD − 0.5 V
VIN1 = VDD / 2 − 0.05 V
VIN2 = VDD / 2 + 0.05 V
−
+
VIN1
A
IOSINK
VIN2
VO = + 0.5 V
VIN1 = VDD / 2 + 0.05 V
VIN2 = VDD / 2 − 0.05 V
VO
7. Common Mode Input Voltage, VCM & Common Mode Rejection Ratio, CMRR
VDD
CMRR
RF = 680 kΩ
RS = 6.8 kΩ
VIN1 − VIN2
VO1 − VO2
CMRR = −20log
−
+
VO
RS = 6.8 kΩ
×
RS
RS + RF
Measure VO corresponding to VIN1 = 1.45 V and VIN2 = 1.55 V
VDD
VIN
2
RF = 680 kΩ
8. Total Harmonic Distortion, THD
VDD
THD
RF
Gain Variable
RS
−
+
VO
Gain Variable
RF / RS = 20log (100 kΩ / 1 kΩ) = 40 dB
RF / RS = 20log (100 kΩ / 100 kΩ) = 0 dB
freq = 100 Hz, 1 kHz, 10 kHz
30 kHz LPF ON
VIN
VSS
9. Slew Rate, SR
10. Gain, AV & Phase, GBW
VDD
VDD
RF = 680 kΩ
RS = 6.8 kΩ
−
+
VO
1 MΩ
VSS
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
−
+
20 pF
VO
1 MΩ
20 pF
RS = 6.8 kΩ VSS
Page 21 of 24
HA1630S04/05/06 Series
Package Dimensions
JEITA Package Code
RENESAS Code
Previous Code
MASS (Typ) [g]
SC-74A
PLSP0005ZB-A
MPAK-5 / MPAK-5V
0.015
D
A
e
Q
E
HE
L
A
c
LP
L1
A3
A
x M S
A
b
A2
A
A1
y S
S
b
c
A-A Section
Reference Dimensions in millimeters
Symbol
Min
Nom Max
A
A1
A2
A3
b
c
D
E
e
HE
L
L1
LP
x
y
Q
1.0
0
1.0
⎯
0.35
0.11
2.8
1.5
⎯
2.5
0.3
0.1
0.2
⎯
⎯
⎯
⎯
⎯
1.1
0.25
0.4
0.16
2.95
1.6
0.95
2.8
⎯
⎯
⎯
⎯
⎯
0.3
1.4
0.1
1.3
⎯
0.5
0.26
3.1
1.8
⎯
3.0
0.7
0.5
0.6
0.05
0.05
⎯
© 2013 Renesas Electronics Corporation. All rights reserved.
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 22 of 24
HA1630S04/05/06 Series
JEITA Package Code
RENESAS Code
Previous Code
MASS (Typ) [g]
SC-88A
PTSP0005ZC-A
CMPAK-5 / CMPAK-5V
0.006
D
A
e
Q
c
E
HE
LP
L
A
A
x M
L1
S A
A2
y S
b
c
A-A Section
A3
b
A
A1
S
Reference Dimensions in millimeters
Symbol
Min
Nom Max
A
A1
A2
A3
b
c
D
E
e
HE
L
L1
LP
x
y
Q
0.8
0
0.8
⎯
0.15
0.1
1.8
1.15
⎯
1.8
0.3
0.1
0.2
⎯
⎯
⎯
⎯
⎯
0.9
0.25
0.22
0.13
2.0
1.25
0.65
2.1
⎯
⎯
⎯
⎯
⎯
0.25
1.1
0.1
1.0
⎯
0.3
0.15
2.2
1.35
⎯
2.4
0.7
0.5
0.6
0.05
0.05
⎯
© 2013 Renesas Electronics Corporation. All rights reserved.
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 23 of 24
HA1630S04/05/06 Series
Taping & Reel Specification
[Taping]
Package Code
MPAK-5
CMPAK-5
W
8
8
P
4
4
Ao
3.3
2.25
Bo
3.3
2.45
Ko
1.5
1.1
E
1.75
1.75
F
3.5
3.5
D1
1.05
1.05
Maximum Storage No.
3,000 pcs/reel
3,000 pcs/reel
4.0
φ 1.5
Unit: mm
E
2.0
Cover
tape
B0
W
F
A0
D1
P
Tape withdraw direction
[Ordering Information]
φ178 ± 2
2.0 ± 0.5
W2
9
9
4 ± 0.5
W1
11.4
11.4
0°
Tape width
8
8
12
[Reel]
Package
MPAK-5
CMPAK-5
11.4
φ13 ± 0.5
K0
Ordering Unit
3,000 pcs
9.0
Mark Indication
Index band
Marking
1
D
1D
: HA1630S04
1E
: HA1630S05
1F
: HA1630S06
= Contorol code
( ⎯ or blank)
R03DS0082EJ0200 Rev.2.00
Jan 10, 2014
Page 24 of 24
Notice
1.
Descriptions of circuits, software and other related information in this document are provided only to illustrate the operation of semiconductor products and application examples. You are fully responsible for
the incorporation of these circuits, software, and information in the design of your equipment. Renesas Electronics assumes no responsibility for any losses incurred by you or third parties arising from the
use of these circuits, software, or information.
2.
Renesas Electronics has used reasonable care in preparing the information included in this document, but Renesas Electronics does not warrant that such information is error free. Renesas Electronics
3.
Renesas Electronics does not assume any liability for infringement of patents, copyrights, or other intellectual property rights of third parties by or arising from the use of Renesas Electronics products or
assumes no liability whatsoever for any damages incurred by you resulting from errors in or omissions from the information included herein.
technical information described in this document. No license, express, implied or otherwise, is granted hereby under any patents, copyrights or other intellectual property rights of Renesas Electronics or
others.
4.
You should not alter, modify, copy, or otherwise misappropriate any Renesas Electronics product, whether in whole or in part. Renesas Electronics assumes no responsibility for any losses incurred by you or
5.
Renesas Electronics products are classified according to the following two quality grades: "Standard" and "High Quality". The recommended applications for each Renesas Electronics product depends on
third parties arising from such alteration, modification, copy or otherwise misappropriation of Renesas Electronics product.
the product's quality grade, as indicated below.
"Standard": Computers; office equipment; communications equipment; test and measurement equipment; audio and visual equipment; home electronic appliances; machine tools; personal electronic
equipment; and industrial robots etc.
"High Quality": Transportation equipment (automobiles, trains, ships, etc.); traffic control systems; anti-disaster systems; anti-crime systems; and safety equipment etc.
Renesas Electronics products are neither intended nor authorized for use in products or systems that may pose a direct threat to human life or bodily injury (artificial life support devices or systems, surgical
implantations etc.), or may cause serious property damages (nuclear reactor control systems, military equipment etc.). You must check the quality grade of each Renesas Electronics product before using it
in a particular application. You may not use any Renesas Electronics product for any application for which it is not intended. Renesas Electronics shall not be in any way liable for any damages or losses
incurred by you or third parties arising from the use of any Renesas Electronics product for which the product is not intended by Renesas Electronics.
6.
You should use the Renesas Electronics products described in this document within the range specified by Renesas Electronics, especially with respect to the maximum rating, operating supply voltage
range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas Electronics shall have no liability for malfunctions or damages arising out of the
use of Renesas Electronics products beyond such specified ranges.
7.
Although Renesas Electronics endeavors to improve the quality and reliability of its products, semiconductor products have specific characteristics such as the occurrence of failure at a certain rate and
malfunctions under certain use conditions. Further, Renesas Electronics products are not subject to radiation resistance design. Please be sure to implement safety measures to guard them against the
possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas Electronics product, such as safety design for hardware and software including but not limited to
redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other appropriate measures. Because the evaluation of microcomputer software alone is very difficult,
please evaluate the safety of the final products or systems manufactured by you.
8.
Please contact a Renesas Electronics sales office for details as to environmental matters such as the environmental compatibility of each Renesas Electronics product. Please use Renesas Electronics
products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances, including without limitation, the EU RoHS Directive. Renesas Electronics assumes
no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
9.
Renesas Electronics products and technology may not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable domestic or foreign laws or
regulations. You should not use Renesas Electronics products or technology described in this document for any purpose relating to military applications or use by the military, including but not limited to the
development of weapons of mass destruction. When exporting the Renesas Electronics products or technology described in this document, you should comply with the applicable export control laws and
regulations and follow the procedures required by such laws and regulations.
10. It is the responsibility of the buyer or distributor of Renesas Electronics products, who distributes, disposes of, or otherwise places the product with a third party, to notify such third party in advance of the
contents and conditions set forth in this document, Renesas Electronics assumes no responsibility for any losses incurred by you or third parties as a result of unauthorized use of Renesas Electronics
products.
11. This document may not be reproduced or duplicated in any form, in whole or in part, without prior written consent of Renesas Electronics.
12. Please contact a Renesas Electronics sales office if you have any questions regarding the information contained in this document or Renesas Electronics products, or if you have any other inquiries.
(Note 1)
"Renesas Electronics" as used in this document means Renesas Electronics Corporation and also includes its majority-owned subsidiaries.
(Note 2)
"Renesas Electronics product(s)" means any product developed or manufactured by or for Renesas Electronics.
http://www.renesas.com
SALES OFFICES
Refer to "http://www.renesas.com/" for the latest and detailed information.
Renesas Electronics America Inc.
2880 Scott Boulevard Santa Clara, CA 95050-2554, U.S.A.
Tel: +1-408-588-6000, Fax: +1-408-588-6130
Renesas Electronics Canada Limited
1101 Nicholson Road, Newmarket, Ontario L3Y 9C3, Canada
Tel: +1-905-898-5441, Fax: +1-905-898-3220
Renesas Electronics Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K
Tel: +44-1628-651-700, Fax: +44-1628-651-804
Renesas Electronics Europe GmbH
Arcadiastrasse 10, 40472 Düsseldorf, Germany
Tel: +49-211-65030, Fax: +49-211-6503-1327
Renesas Electronics (China) Co., Ltd.
7th Floor, Quantum Plaza, No.27 ZhiChunLu Haidian District, Beijing 100083, P.R.China
Tel: +86-10-8235-1155, Fax: +86-10-8235-7679
Renesas Electronics (Shanghai) Co., Ltd.
Unit 301, Tower A, Central Towers, 555 LanGao Rd., Putuo District, Shanghai, China
Tel: +86-21-2226-0888, Fax: +86-21-2226-0999
Renesas Electronics Hong Kong Limited
Unit 1601-1613, 16/F., Tower 2, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hong Kong
Tel: +852-2886-9318, Fax: +852 2886-9022/9044
Renesas Electronics Taiwan Co., Ltd.
13F, No. 363, Fu Shing North Road, Taipei, Taiwan
Tel: +886-2-8175-9600, Fax: +886 2-8175-9670
Renesas Electronics Singapore Pte. Ltd.
80 Bendemeer Road, Unit #06-02 Hyflux Innovation Centre Singapore 339949
Tel: +65-6213-0200, Fax: +65-6213-0300
Renesas Electronics Malaysia Sdn.Bhd.
Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No. 18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia
Tel: +60-3-7955-9390, Fax: +60-3-7955-9510
Renesas Electronics Korea Co., Ltd.
12F., 234 Teheran-ro, Gangnam-Gu, Seoul, 135-080, Korea
Tel: +82-2-558-3737, Fax: +82-2-558-5141
© 2014 Renesas Electronics Corporation. All rights reserved.
Colophon 3.0