SERIES CLA CUSTOM LINEAR ARRAYS with CREE® XLamp® XP-E LEDs Prolume Series CLA lighting fixtures allow the custom design of hi-flux LED lighting in interior applications including cove and accent lighting, case lighting, back lighting, edge lighting, wall grazing and more. Key features include… LEDs / Optics Arrays use industry leading lumen performance high brightness CREE XLamp XP-E LEDs, ANSI binned in a CCT range from 2700K to 5000K, with a > 50,000 hour life to 70% lumen maintenance. LEDs can be fitted with secondary optics in a range of beam patterns from 15 to 115 to suite the application. Color LEDs available. Consult factory. Electrical Design A uniquely designed illumination board integrates LuxDrive™* circuitry for current regulation and provides both electrical and thermal management of the LEDs. With operating efficiency at > 90%, energy is emitted as light with as little as 5% as heat. Arrays are rated at 24VDC with both standard and hi-output models available. Dimming Array design provides a third rail DIM line for dimming using a 0-10V current sink lighting control protocol. Special dimming drivers are not required. Wiring is shown below… Dimming Schematic *LuxDrive is a registered trademark of LEDdynamics Array Styles Extruded aluminum housings are custom to specific application lengths up to 144” and can be provided in flat channels or Uchannels. Other custom designs can be tailored to application requirements. Standard white textured finish. Custom colors available. Consult Factory. Approvals UL Listed for indoor applications using Class 2 wiring methods Fixture Schedule TYPE Job: Remarks: Model Number Note: The dimming controller must be able to sink .5mA per foot of connected arrays. Less than .5mA will be “off”. If the controller cannot sink .5mA a separate control should be used to disconnect the AC from the LED driver to turn the arrays “off”. POWER AND ILLUMINATION POWER LUMINOUS INTENSITY (Average Lumens / FT) (1) CCT BASIC ARRAY LED CURRENT LED PITCH W/ (2) FT 2700K 3000K 3500K 4000K 5000K CLA3/2 350mA 2” 7.0 379 429 437 445 530 CLA5/2 500mA 2” 10.0 528 600 612 624 744 CLA3/1 350mA 1.2” 12.0 630 714 727 740 880 CLA5/1 500mA 1.2” 17.0 884 1004 1021 1037 1241 Lumen De-Rating Factors: Optics (.7) / Lens (.9) / Optics & Lens (.6) – Multiply factor by table lumens to get actual fixture lumens Notes: (1) Measured after thermal stabilization of LED light engine. (2) Includes driver losses for sizing. (3) Available in U-Channel or custom array style only. Consult factory for custom styles. CONSULT FACTORY FOR WIRING OPTIONS LEDs and OPTICS OPTICS / LENSING LED SELECTOR / ANSI Binned COLOR CCT CRI ORDER SUFFIX OPTICS / VIEWING ANGLE ORDER SUFFIX Warm White 2700K 85 W827 40 Wide W Warm White 3000K 85 W830 15 Spot S Neutral White 3500K 85 N835 50 x 10 Elliptical E N 4000K 85 N740 (NO OPTIC) 115 FWHM Neutral White Cool White 5000K 70 C750 LENSING (OPTIONAL)* Other CCT and CRI options may be available. Color LEDs Available. Consult Factory Clear Lens C Diffused Lens D *Other Lensing options may be available. Consult Factory FLAT CHANNEL F(*) U-CHANNEL U(*) FLAT CHANNEL w / OPTIC F TUBE T 1.62" DIA *ADD SUFFIX M FOR DAMP LOCATION (Silicon moisture barrier construction) / Consult Factory for Custom Channels ORDERING… BASIC ARRAY - LENGTH, ARRAY STYLE, LENS* – LED – OPTIC / TERMINATION EXAMPLE…MODEL CLA3/2 – 24FCM – W830 - N / 10TD Basic Array CLA3/2, 350mA current, 2” pitch, 24” length, Flat channel mount, Clear lens, damp location Moisture barrier construction, Warm white 85 CRI 3000K CCT LEDs, No optic and 10’ Tray cable home run leads for Dimming. Mounting brackets and drivers ordered separately. See separate specification pages for drivers, mounting brackets and termination wiring options. (Form CLA060614.Rev10)