INSTALLATION INSTRUCTION
ACCIAIO
®
BX920
F L U O R E S C E N T
120V, 277V, 347V or 480V Input
T5, T5HO, T8
WET LOCATION / IP66
Durable and Efficient Design
R
C
US
Chain mount (chain optional)
Surface mounting bracket
Safety cable
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / SIZE / OPERATION / LAMP & BALLAST / INPUT
Steel Housing
Die-cast aluminum
end cap
Model:
BX920
Operation HT (AC Only)
SA (AC & Emergency)
Lamps
Input
217WT8
214WT5
224WT5HO
228WT5
232WT8
254WT5HO
120V / 277V
347V or 480V
Tempered glass
Stainless steel lock screw
IMPORTANT SAFEGUARDS
WARNING
No User serviceable parts. Refer service to a qualified service technician.
Read instructions prior to installing and /or operating this device.
Installation should be performed by a licensed electrician / installer
in accordance with local codes.
IMPORTANT SAFETYGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Do not let power cords touch hot surfaces.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where
unauthorized personnel will not readily subject it to tampering.
- The use of accessory equipment not recommended by Beghelli
Inc, may cause an unsafe condition, and will void the warranty.
- Do not use this equipment for other than its intended purpose.
- Servicing of this equipment should be performed by qualified
service personnel.
SAVE THESE INSTRUCTIONS!
012612
INSTALLATIONGUARDS
1. Make sure the main power is off.
2. Attach and secure ACCIAIO® mounting brackets to surface. Use
appropriate fasteners.
3. Assemble safety cable on safety bracket (top of the fixture).
4. Connect safety cables to already installed mounting brackets.
5. Bring the fixture up and snap mounting bracket onto
housing side channels.
6. Connect labeled wires to main power.
RELAMPING
1. Detach mounting brackets from housing having the fixture hang from
safety cables (If there is 48” clearance on site this process is not
necessary see) (figures 2, 3 & 4)
2. Unlock screw from NON-FEED end cap and take end cap off.
3. Extract security crossbar (up – out motion)
4. Partially or completely slide out rail system until lamps are accessible.
5. Repeat the same process in reverse to close and seal the unit.
Beghelli Canada Inc.
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
Tel (905) 948-9500 Fax (905) 948-8673
www.BeghelliLuce.com
INSTALLATION
1
Safety cable
G
N L
2
Connect wires to main power.
(36” standard line cord provided)
power is off
4
Attach mounting
brackets to surface.
G
N
L
Snap fixture
to brackets.
3
5
G
N
Electrical hardware
(provided by others)
BLACK / HOT
WHITE / NEUTRAL
6
GREEN /GROUND
Bracket
L
1. Make sure the main power is off.
®
2. Attach and secure ACCIAIO mounting brackets to surface.
Use appropriate fasteners.
3. Connect safety cable to both brackets (top of the fixture).
4. Connect safety cables to already installed mounting brackets.
5. Bring the fixture up and snap mounting bracket onto
housing side channels.
6. Connect labeled wires to main power.
Fixture completely installed.
RELAMPING
1
2
Detach luminaire from stainless steel, surface mount
brackets. Unit is held by two safety cables that allow the
ACCIAIO® to drop down approximately 12” for
easy accesibility.
Loosen lock screw to release non-feed,
die-cast end cap.
NOTE: UNIT DOES NOT HAVE TO BE DROPED DOWN IF YOU HAVE 48“ BETWEEN UNITS
3
4
Unlock crossbar bracket in an up and out motion
to gain access to the ballast and lamp rail system.
All linear two (2) lamp configurations feature
a single ACCIAIO® rail system. Ratchet sockets must be
turned for lamp removal.
Reverse all steps to close and secure ACCIAIO®
INSTALLATION INSTRUCTION
ACCIAIO
®
BX940
F L U O R E S C E N T
120V, 277V, 347V or 480V Input
T5, T5HO, T8
WET LOCATION / IP66
Durable and Efficient Design
R
C
US
Chain mount (Chain optional)
Mounting bracket
Safety cable
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / SIZE / OPERATION / LAMP & BALLAST / INPUT
Model:
BX940
Operation HT (AC Only)
Die-cast aluminum
end cap
SA (AC & Emergency - one lamp)
SA (AC & Emergency - two lamp)
Steel Housing
Lamps
Input
432WT8
428WT5
454WT5HO
120V / 277V
347V or 480V
Tempered glass
Stainless steel lock screw
IMPORTANT SAFEGUARDS
WARNING
No User serviceable parts. Refer service to a qualified service technician.
Read instructions prior to installing and /or operating this device.
Installation should be performed by a licensed electrician / installer
in accordance with local codes.
IMPORTANT SAFETYGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Do not let power cords touch hot surfaces.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where
unauthorized personnel will not readily subject it to tampering.
- The use of accessory equipment not recommended by Beghelli
Inc, may cause an unsafe condition, and will void the warranty.
- Do not use this equipment for other than its intended purpose.
- Servicing of this equipment should be performed by qualified
service personnel.
SAVE THESE INSTRUCTIONS!
012612
INSTALLATIONGUARDS
1. Make sure the main power is off.
2. Attach and secure ACCIAIO® mounting brackets to surface. Use
appropriate fasteners.
3. Assemble safety cable on safety bracket (top of the fixture).
4. Connect safety cables to already installed mounting brackets.
5. Bring the fixture up and snap mounting bracket onto
housing side channels.
6. Connect labeled wires to main power.
RELAMPING
1. Detach mounting brackets from housing having the fixture hang from
safety cables (If there is 48” clearance on site this process is not
necessary see) (figures 2, 3 & 4)
2. Unlock screw from NON-FEED end cap and take end cap off.
3. Extract security crossbar (up – out motion)
4. Partially or completely slide out rail system until lamps are accessible.
5. Repeat the same process in reverse to close and seal the unit.
Beghelli Canada Inc.
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
Tel (905) 948-9500 Fax (905) 948-8673
www.BeghelliLuce.com
INSTALLATION
1
2
Connect wires to main power.
(36” standard line cord provided)
power is off
Safety cable
4
Attach mounting
brackets to surface.
G
N
L
Snap fixture
to brackets.
5
3
Bracket
G
N
BLACK / HOT
WHITE / NEUTRAL
6
GREEN /GROUND
Electrical hardware
(provided by others)
L
1. Make sure the main power is off.
®
2. Attach and secure ACCIAIO mounting brackets to surface.
Use appropriate fasteners.
3. Connect safety cable to both brackets (top of the fixture).
4. Connect safety cables to already installed mounting brackets.
5. Bring the fixture up and snap mounting bracket onto
housing side channels.
6. Connect labeled wires to main power.
Fixture completely installed.
RELAMPING
1
2
Detach luminaire from stainless steel, surface mount
brackets. Unit is held by two safety cables that allow the
ACCIAIO® to drop down approximately 12” for
easy accesibility.
3
Loosen lock screws to release non-feed,
die-cast end cap. End cap is supported by
a safety cable for easy maintenance.
4
Unlock crossbar bracket in an up and out motion
to gain access to the ballast and lamp rail system.
Crossbar is supported by the safety cable.
All linear four (4) lamp configurations feature
two, independent ACCIAIO® rail systems.
Reverse all steps to close and secure ACCIAIO®
INSTALLATION INSTRUCTION
ACCIAIO
BX950
®
single
COMPACT FLUORESCENT
120V/277V, 347V or 480V Input
WET LOCATION / IP66
Durable and Efficient Design
R
C
Chain mount (Chain optional)
Surface mounting bracket
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LAMP / INPUT
Model: BX950
Operation HT (AC Only)
Die-cast aluminum
end cap
Steel Housing
Lamps
236W
CF
255W
CF
Input 120V/277V
347V or 480V
Tempered glass lens
Stainless steel lock screw
IMPORTANT SAFEGUARDS
INSTALLATIONGUARDS
WARNING
No User serviceable parts. Refer service to a qualified service technician.
Read instructions prior to installing and /or operating this device.
Installation should be performed by a licensed electrician / installer
in accordance with local codes.
IMPORTANT SAFETYGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Do not let power cords touch hot surfaces.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where
unauthorized personnel will not readily subject it to tampering.
- The use of accessory equipment not recommended by Beghelli
Inc., may cause an unsafe condition, and will void the warranty.
- Do not use this equipment for other than its intended purpose.
- Servicing of this equipment should be performed by qualified
service personnel.
SAVE THESE INSTRUCTIONS!
012612
1. Make sure the main power is off.
2. Attach and secure ACCIAIO® mounting brackets to
surface. Use appropriate fasteners.
3. Bring the fixture up and snap mounting bracket onto
housing side channels.
4. Connect labeled wires to main power.
RELAMPING
1. Loosen stainless steel lock screw from feed end cap
2. Release feed, die-cast end cap
3. Slide out rail system to access the ballast and lamps.
4. Disengage and remove lamps from sockets
Reverse all steps to close and secure ACCIAIO®
Beghelli Canada Inc.
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
Tel (905) 948-9500 Fax (905) 948-8673
www.BeghelliLuce.com
US
INSTALLATION
1
Connect wires to main power.
(72” standard line cord provided)
2
power is off
Attach mounting
brackets to surface.
G
N
L
3
WHITE / NEUTRAL
BLACK / HOT
4
GREEN /GROUND
Canopy kit
(provided by others)
G
N
L
Fixture completely installed.
Snap fixture
to brackets.
1. Make sure the main power is off.
2. Attach and secure ACCIAIO® mounting brackets to
surface. Use appropriate fasteners.
3. Bring the fixture up and snap mounting bracket onto
housing side channels.
4. Connect labeled wires to main power.
RELAMPING
1
2
Loosen stainless steel lock screw
from feed end cap
3
Release feed, die-cast end cap.
4
Grasp
here and
pull
Slide out rail system to access
the ballast and lamps.
Disengage and remove lamps from sockets
Reverse all steps to close and secure ACCIAIO®
INSTALLATION INSTRUCTION
ACCIAIO
BX950
®
duo
COMPACT FLUORESCENT
120V/277V, 347V or 480V Input
WET LOCATION / IP66
Durable and Efficient Design
R
C
US
Surface mounting
bracket
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LAMP / INPUT
Die-cast aluminum
end cap
TER
IT
UN
Model: BX950 duo
S
MA
E
AV
SL
IT
UN
Operation HT (AC Only)
Lamps
436W
CF
455W
CF
Input 120V/277V
347V or 480V
Steel Housing
Tempered glass lens
Jumper
cable
(with watertight
connectors)
Stainless steel lock screw
IMPORTANT SAFEGUARDS
INSTALLATIONGUARDS
WARNING
No User serviceable parts. Refer service to a qualified service technician.
Read instructions prior to installing and /or operating this device.
Installation should be performed by a licensed electrician / installer
in accordance with local codes.
IMPORTANT SAFETYGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
1. Make sure the main power is off.
2. Attach and secure ACCIAIO mounting brackets to surface.
(Use appropriated fasteners)
3. Bring MASTER fixture up and snap mounting brackets onto housing side
channels.
4. Bring SLAVE fixture up and snap mounting brackets onto housing side channels.
5. Connect MASTER and SLAVE using jumper cable with watertight connectors.
6. Connect MASTER fixture to main (AC) power following labels information.
7. Turn ON power.
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
RELAMPING
- Do not let power cords touch hot surfaces.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where
unauthorized personnel will not readily subject it to tampering.
- The use of accessory equipment not recommended by Beghelli
Inc., may cause an unsafe condition, and will void the warranty.
- Do not use this equipment for other than its intended purpose.
- Servicing of this equipment should be performed by qualified
service personnel.
1. Disconnet MASTER and SLAVE from jumper cable
loosen stainless steel lock screw from feed end cap.
2. Release feed, die-cast end cap
3. Slide out rail system to access the ballast and lamps.
4. Disengage and remove lamps from sockets
Reverse all steps to close and secure ACCIAIO®
SAVE THESE INSTRUCTIONS!
012612
Beghelli Canada Inc.
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
Tel (905) 948-9500 Fax (905) 948-8673
www.BeghelliLuce.com
INSTALLATION
1
2
Connect wires to main power.
(72” standard line cord provided)
G
N
L
power is off
GREEN /GROUND
WHITE / NEUTRAL
BLACK / HOT
6
Attach mounting
brackets to surface.
G
N
L
Snap fixture
to brackets.
14.370
3-4-5
Canopy kit
(provided by others)
3.150
Fixture completely installed.
1. Make sure the main power is off.
2. Attach and secure ACCIAIO mounting brackets to surface.
(Use appropriated fasteners)
3. Bring MASTER fixture up and snap mounting brackets onto housing side channels.
4. Bring SLAVE fixture up and snap mounting brackets onto housing side channels.
5. Connect MASTER and SLAVE using jumper cable with watertight connectors.
6. Connect MASTER fixture to main (AC) power following labels information.
7. Turn ON power.
RELAMPING
1
2
Disconnet master and slave from jumper
cable, loosen stainless steel lock screw
from feed end cap.
3
Release feed, die-cast end cap.
4
Grasp
here and
pull
Slide out rail system to access
the ballast and lamps.
12.539
Disengage and remove lamps from sockets
Reverse all steps to close and secure ACCIAIO®.
INSTALLATION INSTRUCTION
ACCIAIO
®
BX960
Flood
COMPACT FLUORESCENT
R
120V/277V, 347V or 480V Input
WET LOCATION / IP66
Durable and Efficient Design
Mounting Bracket
C
US
Aluminum non-feed die-cast end cap
U Bracket
EACH MODEL NUMBER CONSISTS OF THE FOLLOWING:
SERIES / OPERATION / LAMPS / INPUT
Aluminum feed die-cast
end cap
Model:
Steel Housing
BX960 Flood
Operation HT (AC Only)
Lamps
Input
236W
CF
255W
CF
120V/277V
347V or 480V
Stainless steel lock screw
Tempered glass lens
IMPORTANT SAFEGUARDS
INSTALLATIONGUARDS
WARNING
No User serviceable parts. Refer service to a qualified service technician.
Read instructions prior to installing and /or operating this device.
Installation should be performed by a licensed electrician / installer
in accordance with local codes.
IMPORTANT SAFETYGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
- Do not let power cords touch hot surfaces.
- Do not mount near gas or electric heaters.
- Equipment should be mounted in locations and at heights where
unauthorized personnel will not readily subject it to tampering.
- The use of accessory equipment not recommended by Beghelli
Inc., may cause an unsafe condition, and will void the warranty.
- Do not use this equipment for other than its intended purpose.
- Servicing of this equipment should be performed by qualified
service personnel.
Make sure the main power is off:
Loosen lock screw and detach feed die-cast end cap.
Loosen set screws / Slide mounting brackets
onto housing through channels.
Position mounting brackets 12” apart (keep set screws loose
until final adjustment).
Mount U bracket on desired surface against the containment
and use proper fasteners (provided by others).
Mount the fixture on installed U bracket using provided
screws.
Tighten set screws.
Adjust desired angle.
Connect labeled wires to main power.
Turn ON power.
RELAMPING
1. Loosen stainless steel lock screw from feed end cap
and release.
2. Release feed die-cast end cap
3. Slide out rail system to access the ballast and lamps.
4. Disengage and remove lamps from sockets.
Reverse all steps to close and secure ACCIAIO®.
SAVE THESE INSTRUCTIONS!
021712
Beghelli Canada Inc.
3900 14th Avenue
Markham, Ontario L3R 4R3 Canada
Tel (905) 948-9500 Fax (905) 948-8673
www.BeghelliLuce.com
INSTALLATION
Containment tab
1
2
Loosen only
(Do not remove)
Set screw (2)
Slide mounting brackets onto housing
up to containment tab.
Detach feed die-cast end cap.
3
4
12.0”
Angle
adjustment
Tighten set screw
N
L
G
Position brackets at (12”) apart
attach feed die-cast end cap.
Use proper fasteners
(provided by others)
Final mounting and adjustment.
RELAMPING
1
2
Loosen stainless steel lock screw
from feed die-cast end cap.
3
Release feed die-cast end cap.
4
Grasp
here and
pull
Slide out rail system to access
the ballast and lamps.
Disengage and remove lamps from sockets
Reverse all steps to close and secure ACCIAIO®.