3430 Quantum Blvd. Boynton Beach, FL 33426 Phone: 954-­‐617-­‐8170 ‘www.xeleum.com InstallaDon Guide LED TUBE RETROFIT This InstallaDon Guide is intended to be used as reference only. InstallaDon should be done by a fully qualified electrician/technician. This document should never be considered as a subsDtute for any provision of a regulaDon, state and/or local code. Please read the enDre user guide to fully understand and safely use this product. WARNINGS: A) Before installing the LED Replacement Tube, Disconnect the power supply to the light/fixture for your safety. Wiring the fixture to use the LED Fluorescent Replacement Tube is simple, but should be performed by a qualified/licensed professional observing normal safety procedures. B) LED FLUORESCENT TUBES: • The two (2) pins at each end of the LED Fluorescent Replacement Tube are internally connected together. You may apply line voltage to either one pin or both. • Never apply both Hot (typically BLACK) and Neutral (typically WHITE) to the same end of the tube! The individual pins at each end are internally shorted! • The LED Fluorescent Replacement Tube fits in any T-­‐Series Medium Bi-­‐Pin (T8/T10/T12) socket. Replacement of the lamp holders is not necessary. • NEVER ATTEMPT TO RETROFIT OR OTHERWISE ALTER IN ANY WAY, ANY FLUORESCENT FIXTURE WITH BUILT-­‐
IN EMERGENCY BATTARY BACK-­‐UP. DOING SO WILL IMMEDIATELY VOIDE THE UL AND NFPA LIFE SAFETY CODE CERTIFICATIONS. INSTALLATION INSTRUCTIONS STEP 1. Unpack the Product: 1) Unpack and carefully examine the product from top to bo8om. 2) Report any damage and save all packing materials, if any part was damaged during transport. 3) Do not a8empt to use this product, if it is damaged. STEP 2. Planning the InstallaBon: This device installaDon requires planning to ensure successful installaDon with minimal complicaDons and down Dme. STEP 3. User ResponsibiliBes: It is the responsibility of the contractor, installer, purchaser, owner, and user to install, maintain, and operate the device in such a manner as to comply with all state and local laws, ordinances, and regulaDons. STEP 4. Product InstallaBon Steps: 1) Disconnect power to fixture at source. DO NOT SIMPLY SWITCH OFF FIXTURE. 2) Remove exisDng fluorescent tubes and safely set aside. 3) Disconnect (cut) wires to ballast leaving enough wire to be Ded off with wire nuts. 4) Tie-­‐off remaining wires a8ached to ballast with wire nuts. 5) See wiring diagram shown on page 2 for fixture rewiring instrucDons. 6) Cut out the provided Warning SDcker on page #2 and tape it in a conspicuous locaDon on the back of the fixture. 7) Install LED Retrofit Tube(s) into fixture. 8) Re-­‐connect power supply and turn on switch. LED Tube InstallaDon Guide ***** S pecificaDons a re s ubject t o c hange w
ithout n
oDce * ****
Page 1 of 3 3430 Quantum Blvd. Boynton Beach, FL 33426 Phone: 954-­‐617-­‐8170 ‘www.xeleum.com InstallaDon Guide LED TUBE RETROFIT BEFORE LED TUBE INSTALLATION: Blue L N Black White Ballast Red L N Blue Black Ballast White Blue Red Fluorescent Tube Fluorescent Tube Fluorescent Tube Blue L N Black White Ballast Blue L N Black White Blue Yellow Red Yellow Blue Ballast Blue Red Red Fluorescent Tube Fluorescent Tube Fluorescent Tube Fluorescent Tube Fluorescent Tube Fluorescent Tube Fluorescent Tube Note: If the ini,al circuit has a starter, it should be removed just like the ballast prior to installa,on of the LED Tubes. LED Tube InstallaDon Guide Page 2 of 2 3430 Quantum Blvd. Boynton Beach, FL 33426 Phone: 954-­‐617-­‐8170 ‘www.xeleum.com InstallaDon Guide LED TUBE RETROFIT AFTER LED TUBE INSTALLATION: Black LED Tube L N White N White L Input: 90– 277VAC Black Input: 90– 277VAC LED Tube LED Tube Note: Power only has to be connected to one lead on each side of the LED Tube. Hooking up power to both leads is acceptable as well and will not damage the LED Tube. L N Black White N Black L Input: 90– 277VAC LED Tube LED Tube LED Tube LED Tube LED Tube LED Tube White Input: 90– 277VAC LED Tube CAUTION: NEVER ATTEMPT TO RETROFIT OR OTHERWISE ALTER IN ANY WAY, ANY FLUORESCENT FIXTURE WITH BUILT-­‐IN EMERGENCY BATTARY BACK-­‐UP. DOING SO WILL IMMEDIATELY VOID THE UL AND NFPA-­‐101 LIFE SAFETY CODE CERTIFICATIONS. WARNINGS: •
Risk of electric shock. Ensure that the power supply is off, when wiring this device. •  The device should be installed by a qualified electrician or technician in accordance with all relevant local codes. •
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects. LED Tube InstallaDon Guide Page 2 of 3 InstallaDon Guide LED TUBE RETROFIT 333 North Bedford Road -­‐ Suite 135 Mount Kisco, NY 10549 Phone: 914-­‐773-­‐6250 ‘ www.xeleum.com Input: 90– 277VAC L Black White N LED Tube Single-­‐Pin tubes are connected the same way with the Load (Black Wire) coming in on one side of the tube and the Neutral (White Wire) coming in on the other side of the tube. Input: 90– 277VAC White N Black L LED Tube CauBon: Do NOT a8empt to connect the connect both the Load (Black Wire) and the Neutral (White Wire) to the same side of the LED Tube. Doing so will damage the tube and void the warranty. Cut out this Warning S,cker on the doHed line and tape it in a conspicuous loca,on on the fixture to keep others from trying to replace this tube with a fluorescent tube. This can cause serious injury! WARNING: This fixture has been modified for LED tubes. The ballast may have been removed or by-­‐passed. Do not install fluorescent lamps in this fixture! LED Tube InstallaDon Guide Page 3 of 3