American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
INSTALLATION & MAINTENANCE INSTRUCTIONS
ACP COMPACT FLOODLIGHT
! WARNING
ENSURE UNIT IS PROPERLY GROUNDED AND DISCONNECT POWER DURING INSTALLATION AND
BEFORE SERVICING TO AVOID THE RISK OF SEVERE OR FATAL ELECTRICAL SHOCK
READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION
! WARNING
RISK OF FIRE. PRODUCT FOR OUTDOOR INSTALLATION AND USE ONLY.
! CAUTION
TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL
AND LOCAL ELECTRICAL/BUILDING CODES. FOR CODE INTERPRETATION, CONSULT LOCAL CODE AUTHORITY
INSTALLATION
YOKE MOUNT: THE YOKE HAS 3 MOUNTING HOLES,
ONE FOR A 3/4" BOLT AND TWO FOR 3/8" BOLTS.
MOUNTING ADAPTORS ARE AVAILABLE TO ALLOW FOR
HORIZONTAL ADJUSTMENT ON POLE TOPS, CROSS
ARMS, ETC. HORIZONTAL ADJUSTMENT MUST BE
DETERMINED BEFORE MOUNTING THE YOKE TO THE
CROSSARM IF THE ACP FLOOD IS BEING MOUNTED
DIRECTLY TO A CROSSARM WITHOUT THOSE OPTIONAL
FITTERS.
CLAMPING
BOLTS (2)
TENON MOUNT: THE COMPACT FLOOD WITH OPTIONAL
TENON MOUNT CAN BE MOUNTED TO A 2" OR 2 1/2"
PIPE TENON. TIGHTEN ALL FOUR SET SCREWS EQUALLY
TO A MAXIMUM OF 350 INCH LBS., THEN TIGHTEN EACH
LOCK NUT TO A MAXIMUM OF 350 INCH LBS. TO
SECURELY ATTACH FIXTURE TO TENON TOP.
WIRING
COMPARTMENT
ADJUSTMENT:
POWER CORD
ENTRY
YOKE MOUNT: INDEX MARKS ARE INDICATED ON
EACH SIDE OF YOKE FOR DETERMINING DESIRED
MOUNTING ANGLES. THE BOLTS ON EACH SIDE OF
YOKE NEED TO BE LOOSENED, VERTICAL ADJUSTMENT MADE AND THEN BOTH BOLTS RETIGHTENED
TO A MAXIMUM OF 400 INCH LBS.
REMOVABLE
PLUG
SCREWS (3)
TENON MOUNT: THE SET SCREWS AND LOCK NUTS
SHOULD BE LOOSENED AND HORIZONTAL ADJUSTMENT
MADE. SET SCREWS SHOULD THEN BE RETIGHTENED
AND LOCK NUTS RETIGHTENED. INDEX MARKS ARE
INDICATED ON TENON FOR DETERMINING DESIRED
ANGLE. LOOSEN BOLT IN CENTER OF TENON MOUNTED
ACP COMPACT FLOOD TO DESIRED ANGLE AND
RETIGHTEN BOLT TO SECURE TENON MOUNT.TIGHTEN
BOLT TO A MAXIMUM OF 400 INCH ILBS.
BREATHING HOLES
CLOSURE
SCREWS (2)
THIS UNIT HAS BEEN DESIGNED WITH THREE
BREATHING HOLES. TWO HOLES IN THE WIRING
COMPARTMENT AREA AND 1 HOLES IN THE BEZEL. ALL
HOLES ARE PLUGGED WITH A SCREW. ONLY IF THE UNIT
IS YOKE MOUNT AND HAS NO PHOTOCONTROL
RECEPTACLE MUST ANY ACTION BE TAKEN. THE SCREW
IN THE BEZEL IS TO BE REMOVED ONLY IF THE UNIT IS
FACING DOWN. ONE OF THE TWO SCREWS IN THE
WIRING COMPARTMENT IS TO BE REMOVED ONLY IF THE
UNIT IS FACING UP. CHOOSE THE SCREW THAT IS NOT
HOLDING DOWN THE CAPACITOR BRACKET.
2
2
1
1
DRAWING NO. A71218 REV B
(FRONT)
©2007 ACUITY LIGHTING GROUP, INC.
Dia
/32
25
ia
6D
7/1
YOKE
MOUNTING
HOLES
PART NUMBER 057-70-71218
YOKE MOUNT
American Electric Lighting a division of Acuity Lighting Group, Inc. Newark, OH
WIRING
YOKE MOUNT: OPTIONAL FACTORY PRE-WIRED
FLOODS ARE FURNISHED WITH 3 FEET OF FLEXIBLE
CABLE READY FOR CONNECTION TO SUPPLY. FOR
STANDARD UNITS THAT ARE NOT PRE-WIRED, OPEN
BEZEL BY LOOSENING THE 2 CLOSURE SCREWS OR
LATCHES LOCATED AT THE TOP OF FLOOD. LIFT THE
SHIELD TO EXPOSE THE WIRING COMPARTMENT.
REMOVE THE COMPRESSION FITTING AND GROMMET,
FEED CABLE THROUGH THE WIRE ENTRY HOLE. SLIP
THE GROMMET AND COMPRESSION FITTING OVER
THE CABLE AND REASSEMBLE TO HOUSING. USING
THE WIRING DIAGRAM AS A GUIDE, MAKE CONNECTIONS
TO THE TERMINAL BLOCK. ATTACH THE GREEN GROUND
WIRE TO THE GROUNDING BOSS WITH THE GREEN
GROUND SCREW PROVIDED. MULTI-VOLT BALLAST ARE
FACTORY WIRED FOR 120V OPERATION UNLESS
OTHERWISE SPECIFIED. CABLE SHOULD BE #16 AWG
MINIMUM, TYPE SJ, SO, OR SJT-WA, SUITABLE FOR
105C OPERATION
HINGE
SCREW
TENON MOUNT: OPEN ACCESS DOOR ON TENON
MOUNT, FEED SUPPLY WIRES THROUGH BOTTOM OF
TENON MOUNT AND OUT ACCESS DOOR. SLIP TENON
MOUNT OVER POLE TENON AND CONNECT SUPPLY
LEADS TO FIXTURE WIRES. PUSH LEADS BACK INTO
WIRING COMPARTMENT OF TENON MOUNT AND
REPLACE COVER.
BEZEL REPLACEMENT
TENON MOUNT
OPEN THE BEZEL BY LOOSENING THE 2 SCREWS OR
LATCHES. LOOSEN THE HINGE KEEPER SCREW AND SLIDE
THE BEZEL OFF. ASSEMBLE THE REPLACEMENT BEZEL IN
THE REVERSE MANNER.
LAMP SERVICING
OPEN THE BEZEL BY LOOSENING THE 2 SCREWS OR
LATCHES. ALLOW IT TO HANG FREELY ON IT’S HINGE.
THE LAMP SHOULD THEN BE UNSCREWED COUNTER
CLOCKWISE UNTIL FREE. THE LAMP CAN THEN BE
REPLACED BY REVERSING THE PROCEDURE.
ENSURE WHEN RELAMPING TO USE THE CORRECT
LAMP TYPE AND VALUE.
RELAMP IN ACCORDANCE WITH THE BALLAST
EMPLOYED FOR A MAXIMUM OF 400W HPS OR 400W MH.
IF LAMP IS MARKED Hg
IT CONTAINS MERCURY.
FOLLOW DISPOSAL LAWS.
SEE WWW.LAMPRECYCLE.ORG
ACCESS
DOOR
SET
SCREWS (4)
DRAWING NO. A71218 REV B
(REAR)
©2007 ACUITY LIGHTING GROUP, INC.
PART NUMBER 057-70-71218
REV
DATE
DESCRIPTION
ECN
BY
-A
B
25-JUL-2005
28-FEB-2007
6-NOV-2007
NEW RELEASE
R034503
MAH
DAH
ADD TEXT FOR PEC AND RELAMPING
ADD LAMP HG NOTE
R040067
R042055
MAH
DAH
GEW
JRC
PART NUMBER.
057-70-71218
DESCRIPTION
APP
DWG NUMBER
INSTALLATION INSTRUCTIONS
ACP COMPACT FLOOD
A71218
SHT 3 OF 3