INSTALLATION NOTES: nBeckon-26
1. Caution and Safety Instructions
• Do not block light emanating from product in
• Qualified personnel must install and/or service
product in a manner consistent with its intended whole or part.
use and in compliance with the National
• Never operate the fixture with missing or
Electrical Code, Canadian Electrical Code, and/
damaged lens. Clean lens on a regular basis.
or all local and provincial codes.
• Entire fixture may become extremely hot. Do
• Follow all product label information and
not touch hot lens or fixture body. Do not touch
installation instructions.
the light source at any time.
• Turn off power at fuse or circuit breaker before
• Keep all O-rings and sealing surfaces clean
installation or servicing.
during installation and servicing; failure to
• The use of damaged components may cause an
unsafe condition and void product warranty.
do this may lead to premature failure of
the product.
2. Product Information
• Suitable for ground-mounted recessed only
• For use in concrete only
• Suitable for wet locations
10.5"/26.7 cm
IP
67
3YJ8
Tools Needed:
15.7"/39.9 cm
• 12’-18’ of 2” x 4” Lumber (installation)
• 1/8" Allen wrench (installation)
• 9/64" Allen wrench (servicing)
• #1 Phillips screwdriver (servicing)
• #2 Philips screwdriver (servicing)
1/2”-14 NPT Knockout (x4)
ARCHITECTURAL & LANDSCAPE LIGHTING | holmlighting.com
A Hunter Industries Company
INSTALLATION NOTES: nBeckon-26
2
3. Product Installation
Line/Hot/Switching
Black (HV: Brown)
Common
White (HV: Blue)
Ground
Green (HV: Green/
Yellow)
0-10V (-)
Gray* (HV: Black)
0-10V (+)
Violet* (HV: Gray)
Wiring Compartment
Cover
FIXTURE
Wiring Chart
BUILDING
Diagrams
*For use with 0-10V driver only
Wiring Compartment
Threaded Knockouts
Gray
Black
White
Purple
Green
Power Requirements
Standard Voltage (SV)
Universal Voltage (UV)
High Voltage (HV)
Input Power
120V
110V to 277V
220V to 240V
Dimming
Phase
0-10V
0-10V
Number of wires
3
5
5
Wire Colors
Black, White, Green
Black, White, Green,
Violet, Gray
Green/Yellow, Brown, Blue,
Gray, Black
ARCHITECTURAL & LANDSCAPE LIGHTING | holmlighting.com
Customer Service 1-844-200-4656
INSTALLATION NOTES: nBeckon-26
3
3. Product Installation
Side View
Side View
Top View
36-42”
2” x 4” Lumber
Bell-Shaped hole
1. E
xcavate 20-inch diameter hole in desired location.
2. Run conduit 3-plus inches deeper than bottom of
construction sleeve (“sleeve”).
3. Choose the ideal “knockouts” to attach the
conduit to the sleeve, and use a tool of choice to
forcefully remove the knockout.
4. Connect the conduit runs to the sleeve with couplings of choice. (1/2”-14 NPT)
5. Remove wiring compartment cover and pull
wiring into sleeve. Leave cover inside sleeve to
prevent loss.
6. Add installation cover onto sleeve using provided
fasteners.
ARCHITECTURAL & LANDSCAPE LIGHTING | holmlighting.com
7. Insert a 2x4 lumber with a length in excess of the
excavated area into the cover’s slot. Secure with
metal fasteners (not provided).
8. Build wooden frame to align and secure construction sleeve during the concrete pour.
9. Ensure frame aligns the top of the cover with
grade for a flush installation. To install the faceplate slightly above grade, raise the frame no
more than 3/8 inches.
Customer Service 1-844-200-4656
INSTALLATION NOTES: nBeckon-26
4
3. Product Installation
Concrete
12”+ Lead Exposed
Gravel
10. Fill hole with 1/2-inch or less gravel higher than
the lower drainage ledge.
11. Pour concrete up to grade.
12. Following sufficient concrete hardening (“curing”), remove wood frame and installation cover.
13. Run incoming wiring from housing through the
wiring compartment cover.
14. Connect wiring from fixture housing to the incoming power lines using the wiring diagram and
approved wire connectors.
15. Seal wiring compartment with cover pressed in
completely.
16. Place the housing inside the sleeve and rotate
according to the proposed directional of light.
17. Insert four screws to secure in desired position.
ARCHITECTURAL & LANDSCAPE LIGHTING | holmlighting.com
Customer Service 1-844-200-4656
INSTALLATION NOTES: nBeckon-26
5
3. Product Installation
18. Using a #2 screwdriver, turn the top adjustment
screw to adjust the direction (or angle) of light.
One full turn = 1-degree. If using a power drill,
reduce torque to less than 50 in-lbs.
ARCHITECTURAL & LANDSCAPE LIGHTING | holmlighting.com
19. Attach faceplate and fasten screws to secure.
Customer Service 1-844-200-4656
D
6
1
D
4. Repair/Replacement Instructions
B
2
②
Y CT
CR IO
IT N
01
1/2
SIO
AN
2
NO
DO
2
01
2/2
TE
DA
DR
FT
AA
A
7/2
AP
VD
AL
L
DIM
TH
IR
EN
D
5/1
5/1
FIN
E
O
J.
AC
PR
RF
N/A
SU
LE
UN
LE
SS
IS
DE : CKE
SIG
D
P
NE
DA RIN
R:
TE T
:
6
DIS
T
1
F
O
1
1
6
01
1/2
G
DU
CT
:
M
N/AATER
IA
L:
CK
BE
PR
O
08
IO
N
VIS
RE
IS
SS
FIN
LE
J.
E
O
AC
PR
RF
N/A
LE
SU
D
IR
N
TIO
RIP
SC
2
2
01
2/2
TE
DE
N
IO
VIS
FT
E0
V
RE
3
O
RE
V
C
EC
E0
00
0
RE
VIS
IO
N
DE
C
SC
RIP
EC
TIO
O
N
00
0
RE
DR
AA
A
7/2
DA
D
AP
VD
AL
L
TH
DIM
AN
G
UN
H:
O
TH
ER
W
IS
E
S
B1
FO
RM
AT
4
O
TH
ER
W
H:
IS
E
SP
D
EC
TO IM
IF
L EN
.X ER SIO IE
.X .XX X ANC NA D:
XX X =
ES L
NS
:
AN X = ±.0
T
D
SC
= ±.0 1
G
SC D EN
AR
LE
±
AL ENO OT
AL
.0 05
S:
E
E:
R
TE ES
E
±1 005
DA EL
S CR
DR IN IN
°
.
FU IT
D TE
AW
CH
1:2 NCTICAL
BY RA :
IO IN
IN
ES
C : WN
NA S
BY HE
G
LL PE
AW
DR
M
BL
SE
AS
O
N,
C
PE
D
/2
7/
TO IM
CIF
12
L EN
IE
DO
EN
.X ER SIO
.X .XX X ANC NA D:
NO SIO
XX X =
ES L
NS
:
T
AN X = ±.0
D
SC
= ±.0 1
G
SC D EN
AR
LE
±.0 0
AL
AL ENO OT
S:
5
E
E:
R
TE ES
E
±1 005
IN
DA EL
S CR
°
.
D DR
FU IT
IN
DR TE
AW
CH
1:2 NCTICAL
BY A :
IO IN
IN
ES
C : WN
NA S
BY HE
G
4
LL PE
Y CT
DE : CKE
CR IO
DIS
SIG
D
IT N
P
SIZ ICA PO
NE
DA RIN
R:
E: L P INTS
TE T
O
TIT
IN
:
TS
LE
:
Y
IN
EE
T
21 G NO
11 .
04
95
SH
XX
XX
O
SIZ ICA PO
E: L P INTS
IN
IT
TS
BE LE: C
CK
PR
O
O
DU
M
N,
N/AATER CT:
AS
IA
L:
SE
M
BL
Y
.
RE
V
H
E un
1 ng te
Sa 940 ine r In
n D erin du
M ia g st
rie
arc m
s
os,ond
C St.
A
92
07
8
3
A
3
B
2
①
C
Standard Optics ( 20º, 40º and 60º)
C
TH
D IS
NO ISCL DRA
PA OSU W
TE RE IN
NT O G/D
LICE F TH O
CU
NSE IS M
IN EN
IS FO T
GRA RM CO
NTE AT NTA
D ION INS
TO TO TR
AN TH AD CO
Y IN IR E
SE N
VE D PA CR FID
NTI RT ET
E
ON IES IN NT
S D AR FORM IA
L
ES E AL
CR L AT AN
IB PR ION D
ED O
PR
AN HIB OF
OP
D/O ITEDHU
N
RIE
R EX TE
ILLU CE R
IN TA
R
ST PT DU
RA AS ST Y
TE EX RI
D PR ES
HER ES , IN
EI SLY C.
N. AU USE
© TH ,
PU
CO
PY ORI BL
RI ZE ICAT
GH D
T H IN ION
UN AD , AN
TE VAN D
R CE /O
IN
DU BY R
ST HU
RI N
ES TE
, IN R.
C.
1
TH
D IS
NO ISCL DRA
PA OSU W
TE RE IN
NT O G/D
LICE F TH OCU
NSE IS M
IN EN
IS FO T
GRA RM CO
NTE AT NTA
D ION INS
TO TO TR
AN TH AD CO
Y IN IR E
SE N
VE D PA CR FID
NTI RT ET
E
ON IES IN NT
S D AR FORM IA
L
ES E AL
CR L AT AN
IB PR ION D
ED O
PR
AN HIB OF
O
D/O ITEDHU
N PR
IE
R EX TE
ILLU CE R
IN TA
R
ST PT DU
RA AS ST Y
TE EX RI
D PR ES
HER ES , IN
EI SLY C.
N. AU USE
© TH , PU
CO
PY ORI BL
RI ZE ICAT
GH D
T H IN ION
UN AD , AN
TE VAN D
R CE /O
IN
DU BY R
ST HU
RI N
ES TE
, IN R.
C.
INSTALLATION NOTES: nBeckon-26
Unfasten faceplate and housing screws, using a 1/8"
Allen wrench. Remove by lifting cap upward. Avoid
using metal tools to protect the powder coat finish.
4
B
B
3
Lift cartridge arm and turn counterclockwise to release lock. Pull complete cartridge out of
fixture housing.
B1 FORMAT REVISION 08/27/12
4
2
3
1
2
A
3
CONFIDENTIAL AND PROPRIETARY
THIS DRAWING/DOCUMENT CO
DISCLOSURE OF THIS INFORMA
NO PATENT LICENSE IS GRANTE
4
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
A
Faceplate and Lens
③
➍
D
D
C
C
Note: Do not remove
adhesive
B
thermal pads. Premature
failure may result.
B
Rotate cartridge arm back into the neutral position.
Twist the optic counterclockwise and pull outward to
remove the optic.
Unfasten one screw only inside the cartridge using
a Phillips #2 screwdriver.
A
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
DIMENSIONAL
TOLERANCES:
A
DENOTES CRITICAL INSPECTION POINTS
DENOTES FUNCTIONALLY CRITICAL POINTS
SCALE:
SIZE:
1:1
THIRD ANGLE PROJ.
E0000
REV
3
ECO
REVISION DESCRIPTION
AAA
7/22/2012
DRFT
DATE
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
ANGLES: ±1°
ALL DIMENSIONS ARE IN INCHES
APVD
2
DO NOT SCALE DRAWING
REL.
DATE:
DRAWN
JG
BY:
CHECKED
BY:
DESIGNER:
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
ARCHITECTURAL & LANDSCAPE LIGHTING | holmlighting.comCREST,
ASSEMBLY
N/A
SURFACE FINISH:
N/A
TITLE:
PRODUCT:
5/11/2016
4
N/A
THIRD ANGLE PROJ.
DRAWING NO.
REV.
E0000
SHEET 1 OF 1
1
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
ANGLES: ±1°
Customer Service 1-844-200-4656
21110494XXXX
MATERIAL:
DIMENSIONAL
TOLERANCES:
REV
3
ECO
REVISION DESCRIPTION
AAA
7/22/2012
DRFT
DATE
ALL DIMENSIONS ARE IN INCHES
APVD
2
DO NOT SCALE DRAWING
DENOTES CRITICAL INSPECTIO
DENOTES FUNCTIONALLY CRIT
SCALE:
1:1
REL.
DATE:
DRAWN
JG
BY:
CHECKED
BY:
DESIGNER:
PRINT
DATE:
5/11/2016
SIZ
TITL
CR
PRO
MAT
N/
INSTALLATION NOTES: nBeckon-26
7
4. Repair/Replacement Instructions (continued)
B1 FORMAT REVISION 08/27/12
3
4
2
3
1
2
CONFIDENTIAL AND PROPRIETARY
CO
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
3
2
THIS DRAWING/DOCUMENT CONTAINS TRADE SE
DISCLOSURE OF THIS INFORMATION TO THIRD PA
NO PATENT LICENSE IS GRANTED TO ANY INVENT
1
CONFIDENTIAL AND PROPRIETARY
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
D
D
⑤
⑥
D
C
C
C
B
NOTE: Remove adhesive label/cover from the
side of the cartridge to expose driver wiring.
Disconnect wire connectors between the
driver and the LED module before completely
removing the LED module.
B
B
Twist and rock the upper cartridge component
to remove top portion.
Unfasten three LED module screws using Phillips #1
screwdriver. Remove reflector adapter ring and LED
module from cartridge platform.
B1 FORMAT REVISION 08/27/12
3
4
2
3
1
2
CONFIDENTIAL AND PROPRIETARY
A
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
N/A
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
DENOTES CRITICAL INSPECTION POINTS
Hunter Industries
DENOTES FUNCTIONALLY CRITICAL POINTS
Engineering
SCALE:
DIMENSIONAL
TOLERANCES:
SIZE:
1:1
REL.
.XX = ±.01
DATE:
.XXX = ±.005
DRAWN
JG
.XXXX = ±.0005 BY:
DENOTES CRITICAL INSPECTION POINTS
CHECKED CRITICAL POINTS
UNLESS OTHERWISE SPECIFIED: ANGLES:DENOTES
±1° FUNCTIONALLY
THIRD ANGLE PROJ.
D
AAA
E0000
REV
⑦
ECO
REVISION DESCRIPTION
SURFACE FINISH:
ALL
7/22/2012
N/A
DRFT
DATE
APVD
THIRD ANGLE PROJ.
3
2
E0000
REV
ECO
REVISION DESCRIPTION
AAA
7/22/2012
DRFT
DATE
SCALE:
DIMENSIONAL
1:1
DIMENSIONS
TOLERANCES:ARE IN INCHES
REL.
.XX =SCALE
±.01 DRAWING
DATE:
DO NOT
.XXX = ±.005
DRAWN
.XXXX = ±.0005 BY:
4 JG
CHECKED
ANGLES: ±1°
PRINT
DATE:
PRINT
DATE:
DO NOT SCALE DRAWING
C
N/A
CREST, ASSEMBLY
21110494XXXX
MATERIAL:
C
N/A
5/11/2016
CREST, ASSEMBLY
⑧
C
B
B
REVISION DESCRIPTION
AAA
7/22/2012
DRFT
DATE
ALL DIMENSIONS ARE IN INCHES
APVD
1:1
REL.
DATE:
DRAWN
JG
BY:
CHECKED
BY:
DESIGNER:
PRINT
DATE:
DO NOT SCALE DRAWING
SIZE:
C
TITLE:
CREST, AS
PRODUCT:
MATERIAL:
N/A
5/11/2016
2
Push black, 6-pin connector downward to unlock it
from the cartridge.
UNLESS OTHERWISE SPECIFIED:
N/A
THIRD ANGLE PROJ.
DIMENSIONAL
TOLERANCES:
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
ANGLES: ±1°
A
DENOTES CRITICAL INSPECTION POINTS
DENOTES FUNCTIONALLY CRITICAL POINTS
SCALE:
1:1
REL.
DATE:
DRAWN
JG
BY:
CHECKED
BY:
DESIGNER:
SIZE:
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
AAA
7/22/2012
DRFT
DATE
ALL DIMENSIONS ARE IN INCHES
APVD
2
DO NOT SCALE DRAWING
4
PRINT
DATE:
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
N/A
TITLE:
CREST, ASSEMBLY
PRODUCT:
THIRD ANGLE PROJ.
DRAWING NO.
ARCHITECTURAL & LANDSCAPE LIGHTING | holmlighting.comN/A
3
ECO
SCALE:
SHEET 1 OF 1
C
SURFACE FINISH:
REVISION DESCRIPTION
E0000
REV
DIMENSIONAL
TOLERANCES:
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
ANGLES: ±1°
CONFIDENTIA
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMA
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBE
DENOTES CRITICAL INSPECTION POINTS
DENOTES FUNCTIONALLY CRITICAL POINTS
1
A
ECO
D
3
REV.
21110494XXXX
N/A
THIRD ANGLE PROJ.
REV.
SHEET 1 OF 1
1
DRAWING NO.
Remove the driver clamp using a
#2 Phillips screwdriver.
E0000
A
Hunter
DRAWING
NO.Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
TITLE:
2
REV
SURFACE FINISH:
TITLE:
MATERIAL:
5/11/2016
UNLESS OTHERWISE SPECIFIED:
1940 Diamond St.
San Marcos, CA 92078
PRODUCT:
PRODUCT:
BY:
DESIGNER:
ALL DIMENSIONS ARE IN INCHES
APVD
3
BY:
SIZE:
DESIGNER:
A
21110494XXXX
MATERIAL:
REV.
E0000
SHEET 1 OF 1
5/11/2016
1
REV
3
ECO
DIMENSIONAL
TOLERANCES:
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
ANGLES: ±1°
DENOTES CRITICAL INSPECTION POINTS
DENOTES FUNCTIONALLY CRITICAL POINTS
SCALE:
1:1
REL.
DATE:
DRAWN
JG
BY:
CHECKED
BY:
DESIGNER:
Customer Service 1-844-200-4656
REVISION DESCRIPTION
AAA
7/22/2012
DRFT
DATE
ALL DIMENSIONS ARE IN INCHES
APVD
2
DO NOT SCALE DRAWING
PRINT
DATE:
5/11/2016
SIZE:
C
TITLE:
CREST, ASSEMB
PRODUCT:
MATERIAL:
N/A
INSTALLATION NOTES: nBeckon-26
8
4. Repair/Replacement Instructions (continued)
3
2
1
CONFIDENTIAL AND PROPRIETARY
THIS DRAWING/DOCUMENT CONTAINS TRADE SECRET INFORMATION OF HUNTER INDUSTRIES, INC. USE, PUBLICATION, AND/OR
DISCLOSURE OF THIS INFORMATION TO THIRD PARTIES ARE ALL PROHIBITED EXCEPT AS EXPRESSLY AUTHORIZED IN ADVANCE BY HUNTER.
NO PATENT LICENSE IS GRANTED TO ANY INVENTIONS DESCRIBED AND/OR ILLUSTRATED HEREIN. ©COPYRIGHT HUNTER INDUSTRIES, INC.
⑨
D
C
B
Remove driver from cartridge.
5. Warranty
UNLESS OTHERWISE SPECIFIED:
SURFACE FINISH:
N/A
THIRD ANGLE PROJ.
DIMENSIONAL
TOLERANCES:
.XX = ±.01
.XXX = ±.005
.XXXX = ±.0005
ANGLES: ±1°
STATEMENT OF LIMITED WARRANTY
E0000
REV
®
3
ECO
REVISION DESCRIPTION
AAA
7/22/2012
DRFT
DATE
ALL DIMENSIONS ARE IN INCHES
APVD
DO NOT SCALE DRAWING
A
DENOTES CRITICAL INSPECTION POINTS
DENOTES FUNCTIONALLY CRITICAL POINTS
SCALE:
1:1
REL.
DATE:
DRAWN
JG
BY:
CHECKED
BY:
DESIGNER:
PRINT
DATE:
5/11/2016
2
SIZE:
Hunter Industries
Engineering
1940 Diamond St.
San Marcos, CA 92078
C
TITLE:
CREST, ASSEMBLY
PRODUCT:
DRAWING NO.
21110494XXXX
MATERIAL:
N/A
REV.
SHEET 1 OF 1
1
Hunter Industries Incorporated (“Hunter”) warrants Holm lighting products to be free of defects in materials or workmanship
under normal use for a period of five (5) years from the date of invoice. If a defect in a Holm product is discovered during the applicable
warranty period, Hunter will repair or replace, at its option, the product or the defective part. This limited warranty does not extend to
repairs, adjustments, or replacement of Holm products or parts resulting from misuse, negligence, alteration, modification, tampering,
or improper installation and/or maintenance of the product. This warranty extends only to the original installer of the product. If a
defect arises in a Holm product or part during the warranty period, contact the local authorized manufacturer’s representative. Hunter’s
obligation to repair or replace its products as set forth above is the sole and exclusive warranty set forth by Hunter. There are no other
warranties, expressed or implied, including warranties of merchantability and fitness for a particular purpose. Hunter will not be liable to
distributor or any other party in strict liability, tort, contract, or any other manner for damages caused or claimed to be caused as a result
of any design or defect in Holm products, or for any special, incidental, consequential, or exemplary damages or any nature, including
without limitation lost business or profits. Notwithstanding the foregoing, if for any reason Hunter is found to be liable, in no event shall
Hunter’s liability exceed the price of the product which gives rise to the claim, loss, or damage.
If you have any questions concerning the warranty or its application, please write to: Customer Service Department Holm, 1940 Diamond Street, San Marcos, CA 92078, U.S.A.
ARCHITECTURAL & LANDSCAPE LIGHTING | holmlighting.com
Customer Service 1-844-200-4656
HOLM-045-IN-Beckon US
7/16