CATALOGUE OF PRODUCTS
“BORIMA”-EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
QC - MODULES ( QUICK CONNECTING MODULES ) AND ACCESSORIES
It is a modern technology ,which enables
cable connections to function inside the
telecommunication networks by pressing in single - core cables.
The QC ( quick connecting modules ) provide:
y Quick connection of copper wires;
y Solid electric connection;
yReliable mechanical contact;
yDirect work without advance preparation of the wires;
yWires with a plastic insulation coating are with diameter from Ø 0.32 to Ø 0.8 mm and diameter of a
insulation coating to Ø 1.47 mm.
“BORIMA”-EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
QC - MODULES ( QUICK CONNECTING MODULES ) AND ACCESSORIES
QC DISCONNECTION MODULE
Module QC - Disconnection module is used for connecting of cables in
Main and Intermediate Distribution frames , Distribution Cabinets and
Distribution End Boxes. It can disconnect the circuit and enable the
measurements over the cable network.
The module consists of:
• Base and Body - made of polycarbonate - incombustible
( fire resistant );
• Working lamella - made of phosphoric bronze and galvanized with silver
with a thickness of 8 μm;
• Pressing lamella - made of phosphoric bronze.
DISCONNECTION MODULE WITH PROTECTION CARTRIDGE
In the base of disconnection module is built-in protection cartridge for
arresters of voltage protection. In the cartridge are mounted high voltage
arresters, which protected eight and ten telephone pairs.
Additional elements:
• Contact lamella and grounding comb – made of phosphoric bronze and
galvanized with silver with a thickness of 8μm;
• Protection cover - made of polycarbonate - incombustible
( fire - resistant )
CONNECTION MODULE
Module QC - Connection module is used for connecting of cables in Main
and Intermediate Distribution frames , Distribution Cabinets and Distribution
End Boxes. It gives a possibility for measuring the cable network.
The module consists of:
• Base and Body – made of polycarbonate - incombustible
( fire resistant );
• Working lamella – made of phosphoric bronze and galvanized with silver
with thickness of 8 μm.
QC – GROUNDING MODULE
Module QC - grounding is used for derivation of control wires with a
perforation plastic insulation to Main or Intermediate Distribution frame,
Distribution Cabinet or Terminal Distribution Box.
It is the same construction as connection module, but it has only 4 pcs
working lamellas.
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
QC - MODULES ( QUICK CONNECTING MODULES ) AND ACCESSORIES
PROTECTION CARTRIDGE FOR DISCONNECTION MODULE
Protection cartridge for disconnection module is an independent
module, which is mounted on disconnection module and allows multiple
mounting and dismounting. It is used for voltage protection for 8 or 10
telephone pairs. In the cartridge are mounted high voltage arresters.
It consists of:
• Body, cartridge “02” - made of polycarbonate - incombustible
• Cover - labeling plate - made of polycarbonate - incombustible,
transparent.
• Contact lamella, grounding comb - made of phosphoric bronze and
galvanized with tin - bismuth ( SuBs ) with thickness 10 μm.
PROTECTION CARTRIDGE FOR CONNECTION MODULE
Protection cartridge for connection module has the same construction
and function as the protection cartridge for disconnection module, and the
contact lamellas are suitable for mounting on connection module .
PROTECTION CARTRIDGE FOR ONE PAIR
Protection cartridge for one pair is an independent module which is
mounted on disconnection module. It used for voltage and current protection
for one pair. It allows multiple mounting and dismounting. On one
disconnection module can be mounted simultaneously
10 ( 8 ) protection cartridges for one pair.
It consists of:
• Body - made of polycarbonate – incombustible ( fire resistant );
• PCB for voltage and current protection;
• Grounding comb - made of phosphoric bronze and galvanized with tin bismuth (SuBs) with thickness 10 μm.
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
QC - MODULES ( QUICK CONNECTING MODULES )AND ACCESSORIES
TOOL AND DEVICES FOR MOUNTING AND DISMOUNTING
TERMINATION TOOL ( TERMINATOR )
It is used for pushing and cutting the excess wire( cable ) in the slot of working lamella
of the modules QC “Borima”.
Body of the termination tool - made of polycarbonate - incombustible ( fire resistant ).
The tool consists of:
• Hook for taking out a pushed wire ( cable );
• Lamella for taking out the arresters from the nests of the protection cartridge.
REMOVING TOOL
It is used for taking out the QC modules from the mounting back mount frames.
Made of polycarbonate - incombustible ( fire resistant ).
COMPENSATOR
The device is used to provide the necessary working advance of the wires on
mounting of the modules of Main and Intermediate Distribution frame.
Made of polycarbonate - incombustible ( fire resistant)
ACCESSORIES
Labelling plate
It is used for placing of note with the help of two consoles / left and right /. The
labelling plate and consoles are made of polycarbonate - incombustible (fire
resistant).
Marking cap
It is used for marking an exact pair from the module QC.
Colour : red, yellow, green, blue or brown. . Made of polycarbonate - incombustible.
Cut - off - plug
It is used to interrupt the circuit of the disconnection module QC or disconnection
protection module QC.
Colour: red, yellow, green, blue or brown. Made of polycarbonate - incombustible.
Cut - off test cord for QC disconnection and disconnection protection modules
It is used as an assistant tool on certain electrical measuring of the circuit. It is
equipped with four-wired cord. Body - made of polycarbonate - incombustible.
Continuity test cord
It is used as an assistant tool on certain electrical measuring of the circuit. It is
equipped with four-wired cord.
Body – made of polycarbonate incombustible.
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
QC - MODULES ( QUICK CONNECTING MODULES ) AND ACCESSORIES
Part ʋ
Type
8326 / 8325 DM-QC - 8"
8329 / 8328 DM-QC - 10"
8327 / 8334 DPM-QC- 10"
8331 / 8330 CM-QC - 8"
8333 / 8332 CM-QC - 10"
8320 / 8321 GM-QC - 8"
8322
GM-QC - 10"
8400 / 8402 PCDM-QC 8"
8410 / 8411 PCDM-QC 10"
8404 / 8406 PCCM-QC 8"
8414 / 8415 PCCM-QC 10"
8520
CCCP-QC 1"
8524
Terminator
RT 8"
RT 10"
8212
C 8"
8211
C 10"
8486 / 8485 LP 8"
Description - quick
connecting system
Height H
Width W
Depth D
Colour
code
(to RAL)
Module - QC - disconnection 8"
Module - QC - disconnection
10"
Module - QC - disconnection with
protection cartridge 10"
Module - QC - connection 8"
Module - QC - connection 10"
Module - QC - ear thing and
shielding 8"
Module - QC - ear thing and
shielding 10"
Protection cartridge for
disconnection module - 8"
Protection cartridge for
disconnection module - 10"
Protection cartridge for
connection module - 8"
Protection cartridge for
connection module - 10"
Cartridge for current and voltage
protection of 1"
Termination tool
Removing tool - for Back mount
frame 8"
Removing tool - for Back mount
frame 10"
Compensator - for Back mount
frame 8"
Compensator - for Back mount
frame 10"
Labeling plate - Module - QC 8"
33 ± 0.5
33 ± 0.5
103 ± 0.8 23.5 ± 0.5
122±0.8
23.5 ± 0.5
7035/7001
7035/7001
32.5 ± 0.5
122 ± 0.8 23.5 ± 0.5
7035/7001
33 ± 0.5
33 ± 0.5
33 ± 0.5
103 ± 0.8 23.5 ± 0.5
122 ± 0.8 23.5 ± 0.5
103 ± 0.8 23.5 ± 0.5
7035/7001
7035/7001
7035/7001
33 ± 0.5
122 ± 0.8 23.5 ± 0.5
7035/7001
37 ± 0.2
23.6 ± 0.5
7035/7001
23.6 ± 0.5
7035/7001
23.6 ± 0.5
7035/7001
23.6 ± 0.5
7035/7001
13
102.5 ±
0.4
119.8 ±
0.4
102.5 ±
0.4
119.8 ±
0.4
48.5
9.8
7035/7001
185
25
42
111,2
25
18
7035
7035
25
130
18
7035
81
88.8
18
7035
81
107.5
18
7035
22 ± 0.4
80.7 ± 0.5 5.5 ± 0.4
7035/7001
22 ± 0.4
97.2 ± 0.5 5.5 ± 0.4
7035/7001
4.4 ± 0.2
8 ± 0.2
37 ± 0.2
37 ± 0.2
37 ± 0.2
8290
MC
Labeling plate - Module - QC
10"
Marking cap
8517
COP
Cut - off - plug
8.6 ± 0.2
23.7 ± 0.4 2.5 ± 0.4
8515
COTCDM-QC
13
48.5
9.8
8516
8202
CTC-QC
Cut - off test cord for QC
disconnection
Continuity test cord
High voltage cartridge
1018/3020/
6017/5012
1018/3020/
6017/5012
7035
13
Ø8
48.5
6
9.8
7035
8488 / 8487 LP 10"
HVA
4.3 ± 0.2
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
QC - MODULES ( QUICK CONNECTING MODULES )AND ACCESSORIES
Colour code ( to AL )
Colour
7035
7001
3020
1018
6017
5012
8001
light - grey
dark - grey
red
yellow
green
blue
brown
Technical Data
Flammability class
Environment temperature
Relative humidity
For modules QC
Contact resistance in zone of pressing wires
Drilling voltage between two next lamellas
to frequency 50Hz per 1 min
Using cables
Weight:
Module QC - connection, disconnection - 8"
Module QC - connection, disconnection - 10"
Module QC - disconnection with protection cartridge 10”
( with arresters )
Protection cartridge for connection,
disconnection module QC for 8” ( with arresters)
Protection cartridge for connection,
disconnection module QC for 10” ( with arresters)
VO to UL 94
-50°C to +60°C
to 80%
< 25 m
2000 Veff
for wires with plastic insulation
coating with diameter 0.32 mm to
insulation coating to 1.47 mm
0.8 mm and
40.4 ± 1 g
46.5 ± 1 g
88.0 ± 1 g
67.0 ± 1 g
78.8 ± 1 g
ELECTRICAL PARAMETERS AND GEOMETRIC DIMENSIONS OF USING ARRESTERS
A. Electrical parameters
B. Geometric parameter
- spark over voltage of the arrester (100 V/s)
230 V ± 20% - body - cylindrical
- impulse spark over voltage (1 kV/μs)
< 750 V
- base diameter - 8 mm
- voltage extinction (R = 600 ; RC = 150 /100 nF) > 100 V
- height - 6.06 mm ± 0.15
- insulation resistance (100 V=)
>1G
- capacity (for 1 MHz)
5 pF
- AC discharge current (10 times; 1 s; 50 Hz)
5A
- discharge current (8/20 s; 10 times)
5 kA
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
JOINT CLOSURE FOR TELEPHONE NETWORK NON PRESSURIZED
XAGA 550
The Joint closure for telephone networks non pressurized - XAGA 550 is a heat shrinkable closure,
used for protection of the cable connections in the telephone networks non pressurized.
It is used for installation of local, underground and pipe cables with a lead or plastic coating.
It uses the Raychem - technology of composite materials; the closure XAGA 550 guarantees an excellent
mechanical stability during and after installation.
The closure includes heat shrinkable sleeve, which isolates, forms and clamps the connection beam and
the metal canister, which forms the internal volume of the closure. Each end of the closure can branch up to
3 cables, and a three finger clamp with thermo- melting adhesive is used. The three finger clamp ( clip ) is a
part from the branched kit BOKT - 5.
One branched kit is designed for max. 2 cables branched in the one end only.
The heat - shrinkable sleeve is:
- CWST - reinforced with integrated metal coating;
- WRGT - non-reinforced.
The closures XAGA 550 are with capacity to 1800’’.
“BORIMA”-EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
XAGA 550
XAGA 550 kit consists of:
Heat-shrinkable sleeve;
Metal canister; flexible channels and under
clip;
Aluminum foils;
Emery tissue;
Silica gel;
Aluminum cable foils;
Installation procedure;
Shield continuity wire assembly.
BOKT KIT -5 consists of:
Three finger clamp (clip) with thermo-melt
adhesive;
Shield continuity wire assembly;
Aluminum foils.
Description BOKT -5
BOKT -5 S-branched kit with small clamp;
BOKT -5 M-branched kit with middle clamp;
BOKT -5 L-branched kit with large clamp.
DIMENSIONS
Dimensions in mm
Part ʋ
Type
CWST Reinforced closure
8376
XAGA 550 43/8 150
8377
XAGA 550 43/8-190
8378
XAGA 550 43/8-250
8379
XAGA 550 43/8-370
8380
XAGA 550 55/12-180
8381
XAGA 550 55/12-400
8385
XAGA 550 75/15-260
8386
XAGA 550 75/15-340
8387
XAGA 550 75/15-450
8382
XAGA 550 100/25-590
8383
XAGA 550 125/30-560
8384
XAGA 550 164/42-500
Number
of pairs
5 50
10-70
10-100
70-150
70-200
70-200
200-300
200-300
200-300
300-500
500-800
1200-1800
Max.dia
Min.cable Max. jacket
.over
liner D dia. d min opening L
max
43
43
43
43
55
55
75
75
75
100
125
164
8
8
8
8
12
12
15
15
15
25
30
42
150
180
240
340
180
340
210
340
460
560
560
500
Max.
sleeve
length S
350
390
450
570
380
680
450
570
680
900
900
920
Clamp
S
S
S
S
S
S
S
S
S
M
M
M
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
BACK MOUNT FRAMES FOR MOUNTING OF MODULES - QC
The back mount frames are an universal equipment, used for attaching and mounting of modules QC.
The back mount frames are designed for the following modules:
• Modules QC, produced by “BORIMA” -EAD.;
• Modules “KRONE” - series LSA+.
The capacity of the back mount frame: from 10” to 500” for 10” module; from 8” to 400” for 8” module.
Material: chrome nickel steel.
Physical and mechanical characteristics of the material
Hardness, HB 30
Electrical conductivity , s
Heat conductivity, W / ( mK )
Magnetic conductivity, Wb / A
192
0.85
14
1.010
“BORIMA”-EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
BACK MOUNT FRAMES FOR MOUNTING OF MODULES - QC
DIMENSIONS
Dimensions in mm
Modules QC “BORIMA”8"
t
W
V
T
25
85
19.5
22
25
85
19.5
35
n
50
Modules QC”BORIMA” 10"
t
W
25
104 19.5
22
25 104 20.5
22
25
104 19.5
35 50
25 104 20.5
35
Part ʋ
Type
8114 - 8127
T 22 - 8"
8004 - 8032
T 35 - 8"
8128 - 8164
T 22 - 10"
8045 - 8110
T 35 - 10"
According customer
request
According customer
request
T 22 - LSA
T 35 - LSA
V
T
n
KRONE 10" LSA +
t
W
V
T
n
50
Description
Back mount frame for mounting of
module T 22
Back mount frame for mounting of
module T 35
Back mount frame for mounting of
module T 22
Back mount frame for mounting of
module T 35
Back mount frame for mounting of
10”LSA module T 22
Back mount frame for mounting of
10”LSA module T 35
8”
8”
10”
10”
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
MULTI - PAIR SPLICING CONNECTOR MARK III
The Multi - pair splicing connector MARK III is used for connecting pair cables in the telecommunication
network by pressing of conductors with copper wires.
The connectors provide:
• quick connection of copper wires ;
• solid electrical contact;
• reliable mechanical contact;
• direct work without advance preparation of the wires;
• different kinds of connections with a diameter of the wires from Ø 0.32 mm to Ø 0.8 mm and a plastic insulation
coating;
Construction:
• the body, consists of two plastic halves with built in working and cutting lamellas - made of shock - resistant
polycarbonate ;
• cover ( upper and lower ) - made of shock - resistant polycarbonate .
The built in working cutting lamellas are made of phosphoric bronze and a galvanized coating with tin - bismuth
( SuBs ).
Production:
MARK III:10 pair - it is designed to connect 10 pairs of multi - pair cable with copper wires.
MARK III:25 pairs - it is designed to connect 25 pairs of multi - pair cable with copper wires.
Tools:
We offer you a kit of tools, production of AMP. to work with multi - pair splicing connector.
“BORIMA”- EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
MARK III
TECHNICAL DATA
Product
Length D, mm
Width W, mm
Height H, mm
Weight, g
MARK III - 10"
71.4
15.8
10.4
9.68
MARK III - 25"
164
14.4
9.6
15
MATERIAL AND COLOUR OF THE PRODUCT
Product
Base(1)
Cover (2)
Cover (3)
MARK III - 10"
Material
Colour
polycarbonate
and/ PBT
polycarbonate
and/ PBT
polycarbonate
and/ PBT
orange, RAL
1028
reseda, RAL
1032
reseda, RAL
1032
Part ʋ
8300
8301
8302
8303
8305
8306
MARK III - 25"
Material
polycarbonate and/
PBT
polycarbonate and/
PBT
polycarbonate and/
PBT
Type
MARK III - 10" jelli filled
MARK III - 10" jelli filled
MARK III - 10" - dry
MARK III - 10" - dry
MARK III - 25" jelli filled
MARK III - 25" jelli filled
8307
MARK III - 25" - dry
8308
MARK III - 25" - dry
Colour
orange, RAL 1028
reseda, RAL 1032
transparent
Description
Multi-pair connector for
10” – jelly filled half-tap
Multi-pair connector for
10” – jelly filled splicing
Multi-pair connector for
10” – dry half-tap
Multi-pair connector for
10” – dry splicing
Multi-pair connector for
25” – jelly filled splicing
Multi-pair connector for
25” – jelly filled half-tap
Multi-pair connector for
25” – dry half-tap
Multi-pair connector for
25” – dry splicing
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
SINGLE HERMETIC CONNECTORS - SHC
The connectors SHC are designed to enable the cable connections to function in telecommunication
network by pressing of conductors with copper wires.
The connectors provide:
• quick connection of single copper wires;
• an auspicious mechanical contact;
• an auspicious electrical contact;
• no necessity of advance preparation of the wires;
• different kinds of connections with a diameter of the wires from 0.32 mm to 0.8 mm and a plastic
insulation coating;
Construction:
• Body and cover -made of incombustible polycarbonate ( fire - resistant );
•Contact lamella - made of phosphoric bronze and a galvanized tin-bismuth ( SuBs ) or tin-lead ( SuPv )
coating - 10 μm;
• The internal space of the connectors ( chamber ) is filled with hydrophobic filler, which guarantees
protection of the contact from humidity and chemical exposures.
The pressing of the wires is made by special tongs.
“BORIMA”EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
SHC
TECHNICAL DATA
Height H, mm
Width W, mm
Depth D, mm
Weight, g
Flammability class
Contact resistance
Environment
temperature
Product
Material
Colour
6.5
8.8
12.4
0.52
VO to UL 94
smaller than 40 m
-50°C to +60°C
SHC
Body
Polycarbonate
glass filled
Transparent
Cover
Polycarbonate
glass filled
Yellow , RAL 1018
Dimension in, mm
Part ʋ
Type
8482
SHC
8204
Tongs for
connector
Description
Single hermetic connector for
copper wires with diameter
0.32 to
0.8 mm
Tool for pressing of SHC
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
MAIN AND INTERMEDIATE DISTRIBUTION FRAME ( MDF )
The main and the intermediate distribution frame ( MDF ) is designed to connect the
subscriber lines, connection lines of the cable telecommunication network and the
station equipment. Inside the distributor can be; arranged the connections, interrupted
the line; measured the stationary and linear part of the network; current and voltage
protected the station equipment and other necessary technical actions. It is designed to
use modules QC.
The main and the intermediate distribution frame ( MDF ) has a cylindrical modular
construction, which allows accomplishment of different kinds of combinations in height
and length.
Construction:
•base - supports the construction and is used for attaching to the floor. It includes a back
mount frame for a cable beam.
It is made of sheet steel and coated with polyester against corrosion;
• working part - includes a vertical support column, horizontal support elements, metal
details , which form arranged construction, coated with polyester against corrosion,
plastic support for back mount frames, made of chrome - nickel sheet - metal, which are
designed to mount modules QC;
•upper part - is used for mounting the construction to the ceiling, it includes a cable
beam crib. It is made of steel coated with polyester against corrosion.
Types:
Bilateral distribution frame “Borima” - If the designer decides and if there is enough
space, the construction can be used as a main distributor of a bigger exchange (it is
recommended for more than 4000 telephone posts ).It is possible to work ( mounting and
serves ) on the both sides. The location of the back mount frames is: on the face side horizonta l, and on back side - vertical.
Wall two - facade distribution frame “Borima” - It is mounted on the wall. The
position of the back mount frames is : horizontal back mount frames for subscriber side in the upper part of the construction; vertical back mount frame for network side - in the
lower part of the construction.
Wall one - facade distribution frame “Borima” - It is mounted on a wall. The position
of the back mount frames is: vertical back mount frames for subscriber and linear part of
the telecommunication network.
Reconstruction of old type of distribution frame - It is used to restore an existing
bilateral construction with modules QC. It is done by a console for reconstruction of
MDF - a vertical part and a support element for reconstruction of a horizontal part.
“BORIMA”- EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
MAIN AND INTERMEDIATE DISTRIBUTION FRAME (REPARTITOR)
TECHNICAL DATA
Horizontal step Tw, mm
Vertical step Tn, mm
Depth D, mm - bilateral
distribution frame
Depth D, mm - wall
distribution frame
Colour
Relative humidity, %
Environment temperature
Type MDF
TFDF
“Borima”
WTFDF
“Borima”
WOFDF
“Borima”
RC-V
RSE-H
BMFH-H
BMFH-V
CFR
250
250
850
700
Light - grey, to RAL7035
80
to 50°C
Description
Two facade distribution frame
for modules - QC
Wall two - facade distribution
frame for modules - QC
Wall one - facade distribution
frame for modules - QC
Reconstruction Console of
MDF - vertical part
Reconstruction Support
element of MDF - horizontal
part
Back mount frames holder horizontal part
Back mount frames holder vertical part
Cartridge for rosette of MDF
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
CROSS CONNECTION CABINET CCC 300” - 2800” P
The Cross connection cabinet CCC 300” - 2800 “ P is an equipment,
which
connects
the main and the distributing cables in the
telecommunication network. The cabinet gives the possibility to arrange
the connections, to interrupt the line and to measure the telecommunication
cable network.
The cabinet is adapted to outdoor use on a concrete fundament.
The body of the cabinet is made of glass filled polycarbonate, that is
incombustible , UV protected, shock-proof, and high weather - resistant.
The base and the roof are made of incombustible polycarbonate.
Hermetically the cabinet is isolated by PVC sealing profile, that keeps the
working parameters in a wide temperature scope
/According to DIN 7863 /.Hermetically the openings of the incoming and the
outgoing cables are isolated by waterproof compounds and fillers . The
cabinet is equipped with back mount frames ( channels ) for modules QC “
Borima”.
The EQUIPMENT consists of :
• modules QC - disconnecting, connecting and grounding modules;
• main frame / contour / - made of zinc galvanized steel and subsequently
coated with polyester paint.
•channels for installing modules QC “ Borima “ 4 pcs.; the length is
according to the capacity of the cables;
•4 entrances between the base and the body, that secure watertight
passage of all the cables / incoming and outgoing /;
•arranged rings;
•cable holders / incoming and outgoing / in the base and the body of the
cabinet;
•fundament bolts for easy installation and levelling ;
• 4 pieces of grounding bolts ;
• a set of lock.
A System for controlling and protecting the cabinet is made according to
an order.
“BORIMA”-EAD.; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
CROSS CONNECTION CABINET CCC 300” – 1200”P
Type
H
W
D
CCC 300”P
CCC 400"P
CCC 600"P
CCC 800"P
CCC 900"P
CCC 1200"P
955
955
1120
1260
1260
1460
700
700
700
700
700
700
335
335
335
335
335
335
Inputs and outputs of the
back mount frames
Flammability class
Relative humidity
Environment
temperature
4 pcs
90 mm each
VO to UL 94
to 100%
-40°C to +70°C
MATERIAL AND COLOUR OF THE PRODUCT
Base elements
Body
Base
Roof
Part ʋ
8500
8501
8502
8503
8504
8505
Type
Material
polycarbonate glass - filled
polycarbonate glass - filled
metal with organic coating
polycarbonate glass - filled
metal with organic coating
Description
Cross connection cabinet with 4 back mount
CCC 300"P frames by
9 modules - QC each
Cross connection cabinet with
CCC 400"P 4 back mount frames
by 11 modules - QC each
Cross connection cabinet with
CCC 600"P 4 back mount frames
by 16 modules - QC each
Cross connection cabinet with
CCC 800"P 4 back mount frames
by 21 modules - QC each
Cross connection cabinet with
CCC 900"P 4 back mount frames
by24 modules - QC each
Cross connection cabinet with
CCC 1200"P 4 back mount frames
by 31 modules - QC each
Colour
light - grey similar to RAL 7035
light - grey similar to RAL 7035
black similar to RAL 9005
light - grey similar to RAL 7035
black similar to RAL 9005
Equipment with modules QC
connection module - 16pcs
disconnection module - 16pcs
grounding module - 4pcs
connection module - 20pcs
disconnection module - 20pcs
grounding module - 4pcs
connection module - 30pcs
disconnection module - 30pcs
grounding module - 4pcs
connection module - 40pcs
disconnection module - 40pcs grounding
module - 4pcs
connection module - 46 pcs
disconnection module - 46 pcs
grounding module - 4pcs
connection module - 60pcs
disconnection module - 60pcs
grounding module - 4pcs
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
CROSS CONNECTION CABINET CCC 1400” – 2800”P
TECHNICAL DATA
Dimension in mm
Type
H
W
D
CCC 1400” P
CCC 1600” P
CCC 1800” P
CCC 2400" P
CCC 2800" P
1260
1260
1260
1460
1460
1440
1440
1440
1440
1440
335
335
335
335
335
Inputs and outputs of
the back mount
frames
Flammability class
Relative humidity
Environment
temperature
8 pcs
each
90 mm
V0 to UL94
to 100%
-40°C to +70°C
MATERIAL AND COLOUR OF THE PRODUCT
Base elements
Body
Base
Roof
Part No
8506
8507
8508
8509
8510
Material
polycarbonate glass - filled
polycarbonate glass - filled
polycarbonate glass - filled
metal with organic coating
Type
Colour
light - grey similar to RAL 7035
light - grey similar to RAL 7035
light - grey similar to RAL 7035
light - grey similar to RAL 7035
Description
Cross connection cabinet with
CCC 1400” P 8 back mount frames
by 19 modules - QC each
Cross connection cabinet with
CCC 1600” P 8 back mount frames
by 21 modules - QC each
Cross connection cabinet with
CCC 1800” P 8 back mount frames
by 24 modules - QC each
Cross connection cabinet with
CCC 2400" P 8 back mount frames
by 31 modules - QC each
Cross connection cabinet with
CCC 2800” P 8 back mount frames
by 36 modules - QC each
Equipment with modules QC
connection module - 72 pcs
disconnection module-72 pcs
grounding module - 8pcs
connection module - 80 pcs
disconnection module-80 pcs
grounding module - 8pcs
connection module - 92 pcs
disconnection module-92 pcs
grounding module - 8pcs
connection module - 120pcs
disconnection module - 120pcs
grounding module - 8pcs
connection module - 140pcs
disconnection module - 140pcs
grounding module - 8pcs
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
TERMINAL DISTRIBUTION BOX 8” - 10” M
The Terminal Distribution Box 8"- 10"M is used to connect
terminal devices by the distributing telecommunication network
with the exchange. It is designed to be used for outdoor (
facades of buildings or poles ) and indoor mounting . The body (
body and cover ) is made of incombustible polycarbonate .
The box is equipped with a back mount frame ( channel ) to 2
modules QC "Borima".
Each box TB 8" - 10"M is equipped with:
• modules QC;
• back mount frames ( channels ) for modules QC;
• grounding bridge with a clip and a cable shoe;
• rubber sealing with an input and output openings - 3 pcs;
• hermetic rubber sealing between the body and the cover;
• clamp for supporting the incoming cable - 2 pcs;
• a kit of screws, washers and pins for outdoor and indoor
mounting;
• a special bolt for closing the box.
“ BORIMA”- EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
TDB 8” – 10” M
TECHNICAL DATA
Height H, mm
173
Width W, mm
131
Depth D, mm
76
Weight – 8”M; 10”M, kg 0.450; 0.470
Inputs / Outputs:
3 rubber seal with possibility
for:
-2pcs input opening for 10”
cable;
-15 pcs output openings for
one pair cable;
- grounding cable
Material of the box
polycarbonate glass - filled
Material of the module
polycarbonate glass - filled
Colour
light - grey, RAL 7035
Flammability class
VO to UL 94
Relative humidity
to 100%
Environment
- 45 to +75 C
temperature
Part No
8265
8266
Type
TDB 8"M
TDB 10"M
Description
Equipment
Terminal distribution box for connection, disconnection - 1pc
8” with backmount frame for 2 Grounding module - 1pc
modules
Terminal distribution box for connection, disconnection - 1pc
10” with backmount frame for Grounding module - 1pc
2 modules
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
TERMINAL DISTRIBUTION BOX 30” - 50” M
The Terminal Distribution Box 30”- 50” M distributes
cables of the secondary cable network and subscriber cables
of the tertiary cable network. It is designed to be used for
mechanical and electrical indoor and outdoor installation
(outer walls of buildings and poles).
The body (body and cover) is made of incombustible
polycarbonate .
The box can be eqipped with a back mount frame up to 6
modules QC (Quick Connecting System) “Borima”.
Each box DB 30”- 50” M is equipped with:
ymodules- QC (disconnecting or connecting);
yback mount frame for mounting of modules QC;
ygrounding bridge with a clip and a cable shoe;
yrubber sealing with 1 inlet and 1 outlet, according to the
capacity;
ycover sealing, made of an air-foamed rubber;
ysupporting bracket of the incoming cable 1 pc;
ya kit of screws, washers and pins for outdoor and indoor
mounting;
ybrackets- 2pcs for mounting on the pole
“ BORIMA”- EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
TDB 30” – 50” M
TECHNICAL DATA
Height H, mm
325
Height H1, mm
350
Width W, mm
190
Depth D, mm
85
Weight 30”M; 50”M, kg
0.912 kg. ÷ 1.082 kg.
Material of the box
polycarbonate glass-filled
Material of the modules
polycarbonate glass-filled
Colour
light grey, RAL 7035
Flammability class
VO to UL 94
Relative humidity
to 100%
Environment temperature
- 45 to +75 C
NOTE: H – Height of the box without brackets (for mounting on the wall);
H1 – Height of the box with brackets (for mounting on the pole).
Part No
Description
8275
TDB 30” M
8277
TDB 50” M
Specification
Equipment with modules QC
Terminal Distribution Box with
capacity from 30” up to 50” and
back mount frame for modules
Connection, disconnection –
according the capacity
Grounding module – 1pc.
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
TERMINAL DISTRIBUTION BOX 70” - 100” M
The Terminal Distribution Box 70” 100” M distributes the
cables of the secondary cable network and the subscriber
cables of the tertiary cable network. It is designed to be used for
mechanical and electrical indoor and outdoor installation.
The body (body and cover) is made of incombustible
polycarbonate.
The box can be equippted with a back mount frame up to 11
modules QC (Quick Connecting System) “Borima”
Each box TB 70” 100” M is equipped with:
y modules QC (disconnecting or connecting);
y back mount frame for mounting of modules QC;
y grounding bridge with a clip and a cable shoe;
y rubber sealing with 1 inlet and 2 outlets, according to the
capacity;
y cover sealing, made of air-foamed rubber;
y supporting bracket of the incoming cable 1 piece;
y a kit of screws, washers and pins for outdoor and indoor
mounting;
y a special bolt for shutting the box
“ BORIMA”- EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
TDB 70” – 100” M
TECHNICAL DATA
Height H, mm
410
Height H1, mm
430
Width W, mm
210
Depth D, mm
100
Weight 70”M; 100”M, kg
0.426 kg. ÷ 1.656 kg.
Material of the box
polycarbonate glass-filled
Material of the modules
polycarbonate glass-filled
Colour
light grey, RAL 7035
Flammability class
VO to UL 94
Relative humidity
to 100%
Environment temperature
- 45 to +75 C
NOTE: H – Height of the box without brackets (for mounting on the wall);
H1 – Height of the box with brackets (for mounting on the pole).
Part No
8278
8282
Description
Specification
Equipment with modules QC
TDB 70” M
Terminal Distribution Box
with capacity from 70” up to
100” and back mount frame
for modules
Connection, disconnection –
according the capacity
Grounding module – 1pc.
TDB 100” M
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
PLASTIC TELECOMMUNICATION CABLE CHUTE
The Plastic chute of telecommunications cables is designed to be used for underground cable lines. Inside
the chute can be mounted mechanical, heat shrinkable or optical closures. It is used for storing of cable
reserve too. They are suitable for mounting around an existing cable because of the need of a future repair
or insurance of diversion without cutting the cable.
Construction:
y Upper and lower shell with four entrances. There is a rubber sealing fixed on the lengthwise of the lower
shell.
y Universal adapters - 2 pcs. specially designed for mounting of HDPE pipe with a diameter of 32 mm and
40 mm for optical cables;
y Closing entrance - 2 pcs. Conical deaf entrances are used for sealing of the unused entrances;
y Metal supporting frame
The Shells are mounted with stainless screwed connections.
“BORIMA”- EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
PLASTIC TELECOMMUNICATION CABLE CHUTE
Part No
8443
Material – upper and lower shell They are made of polypropylene with 30% glass
Colour
Yellow, RAL 1018
Universal adapters
Bolt connections
Support frame
Colour
Polypropylene
Stainless steel
Steel with powder coating
Grey RAL 7035
Technical data
Mechanical stability
- Loading (5 min)
- Hit (10 times)
-16 kN over the whole surface of the chute
- 6 kg guillotine, falling from 90 cm. height to the
center of the chute
- 7 kg device with point hit, falling from
80 cm height, depth entering 20mm to the center
of the chute
Average tightness
Round 27 kg.
- Hit (1 time)
Tightness with universal adapters
Weight
A complete set of a chute
No
1
2
3
4
5
6
7
8
9
10
Description
Upper shell
Lower shell
Metal support frame
Universal adapters - set
- set of rubber seals
- rubber entrance 32 and 40
Plug-up entrance 32 and 40
Protection gel
Cleaning tissue
Protective covers
Screwed connections
Seal rubber for replacement - 4 m and adhesive
Piece per set
1
1
1 according to the customer
request
2
2
1
2
1 kit
1 kit
according to the customer
request
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
MECHANICAL AND FIBER-OPTIC CLOSURES
Mechanical and fiber optic closures, serve for protection of connections in non-pressurized networks. Fits
different types of cables:
y Telecommunications
- Plastic coated copper cables;
- Fiber optic cables / for closure type MAM /.
y Electric/power cables
- Up to 1000 Volt
Benefits:
y Quick and easy installation;
y No special tools needed;
y For multiple use;
y For aerial and underground installations.
One closure kit consists of two symmetrical half-shells with a foamed rubber length seal fixed in the top shell
/ excluding FDM1 and FDM2, where the design is type “Jar”/. Entry seals keep the closure absolute
watertight. The shells are screwed together with nuts and bolts, made of stainless steel.
“BORIMA”-EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
MECHANICAL IN – LINE CLOSURE FOR CONVENTIONAL COPPER
CABLES TYPE MVM
One closure kit consists of:
y
y
y
y
y
Two symmetrical half-shells, made of material polypropylene - colour yellow (RAL1023);
Foamed rubber length seal of the shell;
Rubber seals between the two halves at closure installation;
Bolt splices for mechanical connection of the shells;
Cable holders
Types:
y
In-Line mechanical closure MVM 23 / 200 - suitable for 2 pcs. of cable with diameter up
to 23 mm;
Part No
Type of the
closure
Max. number
pair
8360
MVM
23/ 200
30
Outer diameter of
the cable
2 ɯ8
23
Splice opening
length (mm)
Dimension of the
closure
DxWxH
200
470ɯ133ɯ90
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
MECHANICAL BRANCH-OFF CLOSURE TYPE MAM FOR
CONVENTIONAL COPPER CABLES AND OPTICAL FIBERS
One closure kit is the same as the In-Line closure type MVM
Type MAM is with two entrances and with two outlets.
Types:
y
Mechanical Branch-off closure type MAM 23 / 200 - suitable for 4 pcs of cable with diameter up
to 23 mm
Part No
Type of the
closure
Max. number
pair
8358
ɆȺɆ 23/ 200
50
Outer diameter of
the cable
4 ɯ8
23
Splice opening
length (mm)
Dimension of
the closure
DxWxH
200
470ɯ223ɯ104
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
MECHANICAL CLOSURE TYPE FDM
The closures type FDM are type “Jar” for making of In-Line and Branch-off connections
One closure kit consists of:
y
Body - made of material polypropylene
y
Cover - made of material polypropylene - black ( RAL 8022 );
y
Rubber seal;
y
Former (schablone) and keys (for FDM 2).
Types:
y
y
Mechanical closure FDM 1 - suitable for 4 pcs of cable from
Mechanical closure FDM 2 - suitable for 4 pcs of cable from
6 to
6 to
14 mm
25 mm
Part No
Type of the
closure
Max. number
pair
Outer diameter of
the cable (mm)
Splice opening
length (mm)
Dimension of
the closure
( x L)
8362
FDM 1
30
4 x 6 - 14
230
75 x 170
8363
FDM 2
70
4 x 6 - 23
120
100 x 280
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
FIBER – OPTIC CLOSURE– 23 / 200 F
The fiber optic closure is designed to connect optical cables with metal elements or dielectric in the
following cases:
y
In–Line and In–Line–Branch–off closure - 1 : 1; 1 : 2; 1 : 3 at maximum
8 pcs of cassettes for organization of the welding;
y
End closure - 1 : 1 to 1 : 2;
y
Branched-Transit closure - 1 : 1; 1 : 2 (without cutting-off the base cable).
The closure is designed for optical cables with outer diameters from 6 to 23 mm.
Installation:
At environment temperature -from - 5 C to +50 C and relative humidity to 98 % without condense humidity.
Part No
with / without
heat shrinkable
splice
protection
Type of the
closure
Fiber optic
splice
cassette
8353 / 8353 ɚ
ɆȺɆ 23/ 200 FO 12 fibers
2
4 ɯ8
8354 / 8354 ɚ
ɆȺɆ 23/ 200 FO 24 fibers
3
8355 / 8355 ɚ
ɆȺɆ 23/ 200 FO 48 fibers
8356 / 8356 ɚ
ɆȺɆ 23/ 200 FO 72 fibers
Splice
opening
length
(mm)
Dimension of the
closure
DxWxH
23
200
470ɯ223ɯ104
4 ɯ8
23
200
470ɯ223ɯ104
5
4 ɯ8
23
200
470ɯ223ɯ104
7
4 ɯ8
23
200
470ɯ223ɯ104
Outer diameter of
the cable
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
METAL NICHE TYPE CABINET
Distribution Metal Niche (Type Cabinet)
The Distribution Metal Niche is designed to be used for indoor telephone installations, located in
buildings and it connects the incoming cable from the cable network with terminal devices.
yThe Distribution Metal Niche is made of metal sheets with thickness 1.5 mm;
yThe Coating is powder painted with colour RAL 7035 or according to the request of the customer;
yTypes:
- with one door;
- with two doors;
yThey are equipped with safety locks with one and the same combination.
“BORIMA”-EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
METAL NICHE – TYPE CABINET
TECHNICAL DATA
Part No
8390
8391
8392
8393
8394
•
•
H, mm
350
400
500
600
800
W, mm
350
400
500
700
700
D, mm
100
100
100
200
200
According to an order they can be produced with dimensions specified by the customer.
The Equipment – chrome-nickel back mount frames for modules type “Borima” or according to the
order of the customer.
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
GROUNDING KITS series SG
Grounding kits series SG are designed to meet the most severe grounding system requirements for
wireless communication systems. A well designed transmission line system uses grounding kits to provide
a bond between the cable and the tower / earth ground system to protect radio components from lightning
transients. One grounding kit is recommended at tower top, tower bottom, at 200 ft
(60 m) intervals (where applicable), and at the entrance to the equipment shelter. Grounding kits are
designed for fast, easy installation on coaxial cable. They utilize a copper clip for easy snap-on installation
to the cable's outer conductor.
A Kit includes:
• Copper clip, riveted to the grounding wire;
• Fasteners for fixing to the tower;
• Two-part weatherproofing tapes.
“BORIMA”-EAD; Tel.: 359//670//6 40 71; Fax: 359//670//6 29 95; e-mail: office@borima-bg.com
GROUNDING KITS series SG
Characteristics
Material
Clip
Copper
Bail
Stainless Steel
Rivets
Copper
Cable shoes
Tin Plated Copper
Bonding Conductor
7-Strand Copper Wire Cross-Sectional Area
16ɦɦ2
Mechanical
Part No
Fits cable diameters According customer
request
According customer
request
According customer
request
8549
Cable shoes clearance holes
SG 1 5/8" 49.0 mm to 50.8 mm
3/8 – 16 or Ɇ10 screws
Bail closure force
Maximum of 11 kg.
SG 1/2"
15.37 mm to 16.83 mm
SG 7/8"
26.7 mm to 28.7 mm
SG 1 1/4"
38.4 mm to 40.1 mm
Environmental
Operating Temperature
-45° to +85°Ñ
Storage Temperature
-45° to +85°Ñ
Weather Resistant *
Salt Spray, Rain, Ice, Wind, UV
* GROUNDING KIT series SG is supplied with weatherproofing material which must be installed properly to insure optimum performance in these
conditions.
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
FIXING CABLE CLAMPS
The fixing cable clamps are used for fixing and strengthening of cables and tubes with different
function.
They are made of corrosion-proof metal elements and calibrated shells from polyamide, UV and ageing
resistant.
The protection of the cable or the tube against possible damage is ensured with the help of the strong
polyamide shells, combined with tightening bolt.
An additional reliable catching achieved, using self-locking nut.
They give possibility for installation at:
• Flat profiles with thickness maximum to 10 mm (Fig.1);
• Tubes with diameter maximum to 18 mm (Fig.2);
• Metal ropes with diameter maximum to 18 mm (Fig.3).
“BORIMA” - EAD; Tel.: 359//670//6 40 71; Fax: 359//670//6 29 95; e-mail: office@borima-bg.com
FIXING CABLE CLAMPS
Fig.1
Fig.2
Fig.3
Material
Metal part of the clamp
Stainless steel
Shells
Polyamide, black
Connecting elements
Stainless steel
Types:
The types are according to the dimensions of the outer diameter of the cable or the tube, which
they fix.
Part No
Fixing cable clamp
Fixing cable clamp
Fixing cable clamp
Fixing cable clamp
Fixing cable clamp
1 ǫ”
1 ¼”
Ǭ“
½”
R8
Single
According customer
request
According customer
request
According customer
request
According customer
request
According customer
request
Double
Triple
8450
8548
8493
8547
8452
8546
8451
8545
8453
-
The types are according to the number of cables or the number of tubes, which they fix.
Single
With two polyamide shells
Double
With four polyamide shells
Triple
With six polyamide shells
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
TECHNICAL DEVICES FOR MECHANICAL MOUNTING
The technical devices for mechanical mounting are used for building and operation of aerial cable
communication lines, which are done through communication cables with a self carrying rope. They are made of
steel and anti-corrosive coating.
Types:
•
•
•
•
•
•
•
Carrier horizontal for concrete poles;
Carrier horizontal for wooden poles;
Tie-bar with thread M8; M10; M12;
Carrier transitional 16;
Clamp three layered;
Clamp transitional
5.5;
Clamp transitional
7.
“BORIMA” - EAD; Tel.: 359//670//6 40 71; Fax: 359//670//6 29 95; e-mail: office@borima-bg.com
TEHNICAL DEVICES FOR MECHANICAL MOUNTING
The technical devices for mechanical mounting
Carrier horizontal for concrete poles
Part No - 8495
Carrier horizontal for wooden poles
Part No - 8463
Carrier transitional
Part No
8496
8497
16
L, mm
310 ±2
400 ±2
N, mm
206 ±1
305 ±1
Tie-bar with thread Ɇ8; Ɇ10; Ɇ12
Part No – according customer request
L
min
max
D
R
Ɇ8
290
380
20
10
Ɇ10
365
455
20
10
Ɇ12
395
490
24
12
Clamp three layered
Part No - 8464
Clamp transitional
Part No - 8465
5.5
Clamp transitional
Part No - 8462
7
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
ROLL LINEAR
Roll linear is used for mechanical laying of the cables at building of cable traces. It assists the cables stringing
for getting of their maximum permissible length and the usage of minimum number of joint closures. It is made of
polyamide.
The roll linear consists of:
• A base made of polyamide, on which there are four openings for fixing to a foundation.
• A roll fixed with a shaft and bearings to the base.
“BORIMA” - EAD; Tel.: 359//670//6 40 71; Fax: 359//670//6 29 95; e-mail: office@borima-bg.com
ROLL LINEAR
Part No
8449
Base
Roll
MATERIAL
Polyamide, white
Polyamide, white
TECHNICAL DATA
Height, mm
Width, mm
Length, mm
Environment temperature
190
218
277
-40° to +70°Ñ
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
METAL BOXES
The metal boxes can be used according to the needs of the customers. They are made of sheet material with
thickness from 1 to 1.5 mm.
The thickness of the sheet material and overall dimensions of the boxes can be manufactured according to
customers' request.
The coating is made of powder painting with a colour in compliance with the customers' request.
They are equipped with secret locks.
“BORIMA” - EAD; Tel.: 359//670//6 40 71; Fax: 359//670//6 29 95; e-mail: office@borima-bg.com
METAL BOXES
Part No
8469
8475
8476
8474
H,
mm
244
400
450
550
W,
mm
196
400
350
400
D,
mm
115
250
250
250
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
TERMINAL FIBER OPTIC BOX
The Terminal Fiber Optic Box serves to organize and protect the fiber optic cable joints from dust and
mechanical damages.
The design allows easy access to all joints and connections.
It is made of metal sheets with 0.8 mm thickness.
The coating is powder paint - color is according to customer's request.
The Terminal Fiber Optic Box is designed for four pieces of optical fibers.
The Terminal Fiber Optic Box consists of:
• Body ;
• Cover;
The Terminal Fiber Optic Box can be made with or without equipment.
The equipment includes:
• Heat shrinkable protective sleeve Holder 1 piece;
• SC duplex adapter 2 pieces;
• Connectors 2 pieces;
• Heat shrinkable protective sleeves 4 pieces;
The Terminal Fiber Optic Box's dimensions and type of equipment can be made according to
customer's request.
“BORIMA”-EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
TERMINAL FIBER OPTIC BOX
Part No
W,
mm
W 1,
mm
H,
mm
D,
mm
8309
155
200
110
33
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
ODF DISTRIBUTOR
ODF Distributor serves to organize and protect fiber optic connections from dust and mechanical
damages.
The design allows easy access to all connections and joints.
It is made of metal sheets with 1 mm thickness.
The coating is powder paint - color is according to customer's request.
Types of ODF Distributors according to their capacity.
• For 12 optical fibers;
• For 24 optical fibers;
• For 48 optical fibers;
• For 96 optical fibers;
ODF Distributor consists of :
• Body ;
• Cover;
• Locks 2 pieces - according to customer's request;
• Leads - according to customer's request.
ODF can be made with or without equipment.
The equipment includes:
• Splice cassettes - their number depend on the capacity;
• SC duplex adaptor - the number depends on the capacity;
• Connectors - the number depends on the capacity;
• Heat shrinkable protection sleeves - the number depends on the capacity;
The ODF - Distributor's dimensions and type of equipment
can be made according to customer's request.
“BORIMA”-EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
ODF DISTRIBUTOR
Part No
Type
H,mm
8498
8499
8311
8312
8313
8314
ODF1
ODF2
ODF 12 Ɉȼ
ODF 24 Ɉȼ
ODF 48 Ɉȼ
ODF 96 Ɉȼ
44
90
44
44
44
90
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
WALL TELECOMMUNICATION CABINET 6 U
The Wall Telecommunication Cabinet 6U is designed for installation of 6 ODF distributors.
The Wall Telecommunication Cabinet 6U consists of:
• Assembly Columns - 1.2 mm sheet steel;
• Upper and Lower Panels - 1.2 mm sheet steel;
• Side opening Panels - 1.2 mm sheet steel;
• Rear Panel - 1.2 mm sheet steel;
• Door metal frame made of plexiglas or sheet steel 1.2 mm ;
• 19” mounting rail - two pieces, 1.2 sheet steel;
• Safety lock;
The coating is powder paint and color is according to customer's request.
It is designed for indoor installation.
There is a possibility for a fan to be mounted inside the Cabinet.
The design allows easy access to all ODF distributors.
The Wall Telecommunication Cabinet can be made to 45 U according to customer's request.
“BORIMA”-EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
WALL TELECOMMUNICATION CABINET 6 U
Part No
W,
mm
H,
mm
D,
mm
8310
570
470
320
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
FIBER OPTIC CLOSURE
The Fiber Optic Closure is designed to provide protection for all types of joints of fiber optic cables
from mechanical effects and environment influences.
The closure may be used in underground, buried, ground or aerial installation.
The fiber optic closure consists of:
• A Body - made of polyamide;
• A Base with four round and one oval entry port - made of polyamide;
• Closing clamp which is easy to work with when you open and lock the closure - made of polyamide;
• Holder for splice cassette - made of polyamide;
• Splice cassette and cover - made of ABS ;
• Rubber sealing ring placed between the body and base;
The types of Fiber Optic Closure are according to their capacity:
• For 12 optical fibers;
• For 24 optical fibers;
• For 48 optical fibers;
• For 96 optical fibers;
Equipment:
• Heat shrinkable protective sleeves - their number depends on the capacity, they serve to protect the
joint optical fibers;
• Heat shrinkable sleeve - 5 pieces, which seals the incoming cables;
• Branch-off clip - 1 piece is used for branching cables;
• Aluminium foil;
• Spanner;
• Grounding cable;
• Pig tails;
• Metal Holder - 1 piece is used for ground closure installation ;
“BORIMA”-EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
FIBER OPTIC CLOSURE
The closure is designed for fiber optic cables with outer diameter up to 18 mm.
The closure is made of black impact resistant polyamide and flammability class V0 in compliance with
UL 94.
Installation:
When the temperature of the environment is from - 5°C
condensed moisture.
Part No
Type of Closure
8315
8316
8317
8318
For 12 optical fibers
For 24 optical fibers
For 48 optical fibers
For 96 optical fibers
to +50°C and relative humidity is to 98 %
Number of cassettes for
optical fibers
1
1
2
4
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
BRANCH OFF KIT FOR CABLE BRANCHING SYSTEM (BOKT)
Branch off kits are designed for branching cables of heat shrinkable closures. The three types of Branching
kits (BOKT) cover all sizes of cables. Three-finger construction helps in perfect branching and reliable sealing,
as the middle finger is coated with hot melt adhesive. It is supplied in kit form with all necessary components for
branching.
One Branching kit (BOKT) is required for branching two cables at one end.
The KIT contains:
• Branch off clip
• Cleaning tissue
• Aluminium cable foil
• Shield continuity wire
• Abrasive strip
Types:
• Two-finger clip
• Three-finger clip Medium
• Three-finger clip Small
“BORIMA” - EAD; Tel.: 359//670//6 40 71; Fax: 359//670//6 29 95; e-mail: office@borima-bg.com
BRANCH OFF KIT FOR CABLE BRANCHING SYSTEM (BOKT)
Branch off kits
Types
The two-finger clip consists of two details with teeth in
their joint parts. It is made of polyamide.
Part No - 8202
Three-finger clip – Medium is made of aluminium alloy
and it is with epoxy-polyester coating. The middle
finger is coated with hot melt adhesive.
Part No - 8206
Three-finger clip – Small is made of aluminium alloy
and it is with epoxy-polyester coating. The middle
finger is coated with hot melt adhesive.
Part No - 8207
“BORIMA” - EAD; tel.: 359//670//6 40 71; fax: 359//670//6 29 95; e-mail: office@borima-bg.com
TELEPHONE BOOTH
The Telephone Booth is designed for mounting telephones sets and as advertising facility.
There is a possibility for setting two telephones on left or right side, in accordance with the
requirements of the customer.
On the Telephone Booth there is also an advertising part on which can easily be put and
respectively replace advertising posters. The advertising part is lit up by light-emitting diodes (LED).
It is made of section steel with hot galvanized coating. It is painted in accordance with the
requirement of the customer.
It is mounted on reinforced concrete foundation.
“BORIMA”-EAD; tel. 359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com
TELEPHONE BOOTH
Part No
8525
H,
mm
2450
W,
mm
1500
D,
mm
9555
“BORIMA” - EAD; tel.359//670//6 40 71; fax 359//670//6 29 95; e-mail: office@borima-bg.com