SENTRY Series
Gasketed Enclosure
SENTRY Series
For Wet and Damp Locations
Description
A.L.P. Lighting Components, Inc. offers the finest manufactured
Gasketed Enclosures, which are totally dust and moisture
resistant. The enclosure is constructed of a fiberglass upper body
and an acrylic, crepe pattern diffuser securely positioned in a
permanent poured in place sealing gasket. The diffuser and
upper components are locked into place by retaining latches,
assuring a secure, tight seal.
The Gasketed Enclosure is a U.L. recognized component,
certified by the NSF International and has the CSA Component
acceptance mark.
By installing a U.L. listed fluorescent strip light or channel type
lighting fixture into the Sentry Series Gasketed Enclosure and
submitting the entire unit to Underwriters Laboratories, a U.L.
Listed fixture suitable for use in wet or damp locations can be
realized.
Approvals and/or Listings
Underwriters Laboratories
NSF International
U.S. Department of Agriculture
Canadian Standards Association
Sentry
Series
Applications
Food Processing Facilities
Kitchens
Parking Garages
Car Washes
Schools
Government Facilities
Industrial Facilities
Public Areas
Features:
STRUCTURALLY RIGID FIBERGLASS BODY
Fiberglass is reinforced polyester and self-extinguishing (ASTM
D635-74). This type of construction does not allow the body
to flex during handling and installation.
GASKETED DIFFUSER RETENTION SLOT
The gasketed inverted U-slot provides a positive continuous
seal between body and diffuser.
BRASS FIXTURE MOUNTING STUD
The fixture studs are integrally molded into the body to
facilitate lighting fixture installation.
HIGH IMPACT ACRYLIC/DR DIFFUSER
Internal crepe pattern allows a smooth exterior surface for
ease of cleaning.
DIFFUSER
The diffuser flange fits snugly into the gasketed retention slot
forming a continuous seal.
En-Seal™
*Consult Factory for IP
Documentation and
required Product
Configurations
To Place an Order or for Additional Information Contact Customer Service
Some Products are Subject to Special Ordering Requirements, Consult Factory
Features and Benefits
FEATURE:
FEATURE:
Continuous poured gasket
One piece construction
BENEFIT:
BENEFIT:
No start or end point to separate
Seal cannot shift
Locks diffuser securely in place
Completely fills channel for
maximum seal integrity
No seams to crack, break or leak
FEATURE:
Fiberglass body
BENEFIT:
FEATURE:
Continuous formed perimeter on
diffuser
BENEFIT:
Virtually unbreakable with superior
corrosion resistance
Maintains true and parallel sides
Provides for positive seal
FEATURE:
FEATURE:
Internal brass studs
Suitcase style standard latch
BENEFIT:
BENEFIT:
Accepts most strip lighting fixtures
No holes are required for
mounting, protecting the integrity
of the housing
Secures positive seal between
housing, gasket and diffuser
FEATURE:
FEATURE:
White polyethylene molded end
plugs
Integral Molded Latch retention
pockets
BENEFIT:
BENEFIT:
Securely locks in latches
Snaps and locks tight to maintain
tight seal of unused end holes
FEATURE:
FEATURE:
High impact acrylic / DR material
diffuser composition
Widest range of materials in industry
External brass studs and optional
stainless steel bracket
BENEFIT:
BENEFIT:
For chain or flush mounting
indoors and out corrosion
resistant
Provides clarity and long life with
impact protection
Standard Assembly consists of fiberglass housing with poured, continuous gasketing, latches, sealing end plugs and high impact acrylic / DR
.
diffuser. Individual components may be purchased separately
2 Foot Enclosure
Shallow Unit
Hole each end .88" DIA (7/8") or
1.125" DIA (1-1/8")
1-1/2"
3-3/16"
5-3/16"
2-1/8"
6-5/8"
External Top View
7"
1/4 - 28 Brass Studs
17-1/2”
Opt. Back Hub Loc.
14-3/4” Stud
3-3/16"
6-5/8”
25-7/8"
25-7/8”
Note: Brass Studs on Inside of Unit are 10-32
4 Foot Enclosure
External Top View
41-1/2”
Opt. Back Hub Loc.
38-3/4” Stud
6-5/8”
50”
Shallow Unit
1/4 - 28 Brass Studs
Hole each end .88" DIA (7/8") or
1.125" DIA (1-1/8")
1-1/2"
3-3/16"
3-3/16"
5-3/16"
2-1/8"
50"
6-5/8"
7"
Deep Unit
Hole each end .88" DIA (7/8") or
1.125" DIA (1-1/8")
1/4 - 28 Brass Studs
1-1/2"
3-3/16"
3-3/16"
5-7/8"
3"
50"
6-5/8"
7"
Note: Brass Studs on Inside of Unit are 10-32
8 Foot Enclosure
External Top View
89-1/2”
Opt. Back Hub Loc.
86-3/4” Stud
5-1/8”
Stud
6-5/8”
98”
Shallow Unit
Hole each end .88" DIA (7/8") or
1.125" DIA (1-1/8")
1/4-28 Brass Studs
1-1/2"
3-3/16”
3-3/16"
5-3/16"
2-1/8"
98”
6-5/8"
7"
Deep Unit
Hole each end .88" DIA (7/8") or
1.125" DIA (1-1/8")
1/4-28 Brass Studs
1-1/2"
3-3/16"
3-3/16”
5-7/8"
3"
98”
6-5/8"
7"
SENTRY SERIES DATA
SENTRY Series
Specifications
Gasketed Enclosures, as manufactured
by A.L.P. Lighting Components, Inc.
shall be U.L. recognized components
for wet and damp locations and have
the CSA component acceptance mark.
The housing shall be one piece
compression molded from U.L.
recognized fiberglass reinforced
polyester. It shall have integral brass
mounting studs for accepting a strip
lighting fixture internally and mounting
brackets externally.
The SURESEAL™ gasket shall be
continuous, poured in place, with no
visible starting or ending points. The
gasket shall fill the perimeter channel of
the housing and provide a continuous
seal between the housing and diffuser.
The diffuser shall be a high impact
acrylic / DR material composition with
an internal crepe pattern to provide a
general lamp obscurity. The diffuser
shall contain a smooth external surface
with a continuously formed perimeter
which maintains true and parallel sides
while providing a positive and
continuous seal.
The full assembly shall have the USDA
and NSF International (Non-Food Zone)
acceptance.
LIGHTING COMPONENTS, INC.
CORPORATE HQ: CHICAGO, IL U.S.A.
CATALOG
CTN
No.
DESCRIPTION
WT
GASKETED ENCLOSURES ASSEMBLIES CONSIST OF:
Housing with (2) 7/8" diameter end holes, High impact Acrylic/DR
Crepe Diffuser, Celcon Latches and end plugs.
F22002*
2' Shallow Gasketed Enclosure Assembly
F240-2*
4' Shallow Gasketed Enclosure Assembly
F240D-2* 4' Deep Gasketed Enclosure Assembly
F296-2*
8' Deep Gasketed Enclosure Assembly
*Add "A" to catalog No. for housing containing 1-1/8" holes
HOUSING ENCLOSURE WITH FOAM GASKETING
2F-0**
70
2' Fiberglass Housing (no holes)
4F-0**
123
4' Fiberglass Housing (no holes)
8F-0**
219
8' Fiberglass Housing (no holes)
2F-1**
70
2' Fiberglass Housing (1 holes 7/8")
4F-1**
123
4' Fiberglass Housing (1 holes 7/8")
8F-1**
219
8' Fiberglass Housing (1 holes 7/8")
2F-2**
70
2' Fiberglass Housing (2 holes 7/8")
4F-2**
123
4' Fiberglass Housing (2 holes 7/8")
8F-2**
219
8' Fiberglass Housing (2 holes 7/8")
2F-1L**
70
2' Fiberglass Housing (1 holes 1-1/8")
4F-1L**
123
4' Fiberglass Housing (1 holes 1-1/8")
8F-1L**
219
8' Fiberglass Housing (1 holes 1-1/8")
2F-2L**
70
2' Fiberglass Housing (2 holes 1-1/8")
4F-2L**
123
4' Fiberglass Housing (2 holes 1-1/8")
8F-2L**
219
8' Fiberglass Housing (2 holes 1-1/8")
**Add "GT" suffix to catalog No. for Gear Tray Housing
SHALLOW DIFFUSERS
2' Acylic / Shallow / Crepe / High Impact
2ARS00
2' Acrylic / DR / Shallow / Crepe
2ARS15
2' Polycarbonate / Shallow / Clear Prismatic
2PPS00
4' Acylic / Shallow / Crepe / High Impact
4ARS00
4' Acylic / DR / Shallow / Crepe
4ARS15
4' Polycarbonate / Shallow / Clear Prismatic
4PPS00
4' Tapered Acrylic Medium Linear Prismatic
4TARSMI
8' Tapered Acrylic Medium Linear Prismatic
8TARSMI
DEEP DIFFUSERS
4' Acylic / Deep / Crepe / High Impact
4ARD00
4' Acylic / DR / Deep / Crepe
4ARD15
4' Polycarbonate / Deep / Clear Prismatic
4PPD00
8' Acylic / Deep / Crepe / High Impact
8ARD00
8' Acylic / DR / Deep / Crepe
8ARD15
8' Polycarbonate / Deep / Clear Prismatic
8PPD00
CTN
QTY
-
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
49
49
49
30
30
30
30
30
30
30
30
30
30
49
49
49
88
88
88
30
30
30
30
30
30
Note: LCW white latches and FEPW white end plugs are available upon
request. Polycarbonate latches and tamper proof latches are also
available. Other replacement diffusers are available (Opal, Prismatic,
Polycarbonate, 100% DR). Contact A.L.P. with requirements.
BRKT 1
LCW
LPC
LCWTP
LPCTP
LSS
LSSTP
DC 2
DC 3
DC 4
FEPW
1125
FEPW
TAMPER BITS
Bracket Assembly Kit (2 Kits Required For 8' Unit)
Celcon Latch
Polycarbonate Latch
Tamper Proof Celcon*
Tamper Proof Polycarbonate Latch*
White End Plug
Stainless Steel Latch
Stainless Steel Tamper Proof Latch with #8-32 x 5/8" T.P. Screws
7/8" Fitting Assembly for 1/2" rigid conduit, with nut
1-1/8" Fitting Assembly for 1/2" rigid conduit with nut
1-1/8" Fitting Assembly for 1/2" rigid conduit without nut
For Customer Support and Service Contact us at:
(877) ALP-LTG1 • FAX: (800) 438-2500 • www.alplighting.com
© 2006 A.L.P. LIGHTING COMPONENTS, INC., PRINTED IN THE U.S.A., GE SENTRY 0806