CAUTION READ BEFORE INSTALLATION
®
NXT PENDANT
Installation Instructions for LNRP3 Surface Mount
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
THIS PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED, IN ACCORDANCE WITH THE APPLICABLE NEC CODE.
• Switch off main power before installation or maintaining fixture.
• Fixtures must be installed in applications where the ambient temperature does not exceed 40°C during normal operation.
• DO NOT connect or disconnect LED board wire connector when fixture is energized, as this may result in permanent damage to
the LED array.
• We will not accept any warranty claims if incorrect driver or light engine is used.
J Box
(By others)
SURFACE MOUNT INSTALLATION
4" octagon J Box
(By others)
3/16"
Max
Spacer
Mounting
Screws
Spacer
1. Attach cross bar to junction box (by others) with 2 flat
head screws provided.
Cross Bar
Mounting
Screws
2
Cross Bar
1
Cross
Bar
2. If the J Box is below the ceiling
panel, spacers on the cross bar
can be removed to compensate.
Remove 2 screws and 2 spacers,
from the cross bar and mount
cross bar to J box. J box maximum
overlap is 3/16"
Wire-nuts
Safety
Cable
3
4
2. Attach Safety cable to slot
in cross bar.
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
4. Make wire connection
with wire-nuts (by others).
Push wire-nuts into
junction box.
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
5
5. Push fixture to ceiling
and lock with clockwise 1/4
turn. Make sure fixture is in
locked position
© 2013. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-207
®
NXT PENDANT
CAUTION READ BEFORE INSTALLATION
Installation Instructions for LNRP3 Surface Mount
IMPORTANT
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
THIS PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND
THE HAZARDS INVOLVED, IN ACCORDANCE WITH THE APPLICABLE NEC CODE.
• Switch off main power before installation or maintaining fixture.
• Fixtures must be installed in applications where the ambient temperature does not exceed 40°C during normal operation.
• DO NOT connect or disconnect LED board wire connector when fixture is energized, as this may result in permanent damage to
the LED array.
• We will not accept any warranty claims if incorrect driver or light engine is used.
Light Engine Replacement
LED power
connector
board part
Reflector
Replacement
Depress small
tab and pull to
release
Light
Engine
Reflector
Alignment Ring
Reflector
Alignment
Ring
1. Unscrew pendant
bottom.
2. Replace reflector.
Note that reflector alignment
ring is only used for 25°, 35°
and 50° reflector.
Pendant
Bottom
1. Unscrew pendant bottom.
2. Remove reflector.
3. Remove reflector alignment ring
(for 25°, 35° and 50° reflector only).
4. Remove LED board connector.
5. Remove 3 screws.
6. Remove light engine.
7. Install new light engine.
Install in reverse order.
3. Screw pendant bottom back in place.
Top Plate
Driver Replacement
LED Driver
LED Driver Plate
2. Disconnect wire-nuts
1. Counter clockwise
1/4 turn to remove
fixture.
3. Disconnect safety cable
4. Remove three screws.
5. Remove top plate.
6. Remove LED driver plate.
7. Remove 2 screws from
LED driver.
8. Replace LED driver.
9. Install new LED driver.
10. Assemble in reverse order.
USAI
Lighting
®
www.usailighting.com
info@usailighting.com
1126 River Road
New Windsor, NY 12553
T 845–565–8500
F 845–561–1130
© 2013. USAI, LLC.
All rights reserved.
All designs protected by copyright.
I2-207