SCHEDULE OF RATES (SOR) FOR WORKS CONTRACT TENDER

advertisement
SCHEDULE OF RATES (SOR) FOR WORKS CONTRACT TENDER FOR MECHANICAL WORKS IN CNG STATIONS AT PUNE
Part - IV
Tender No.: MNGL/C&P/2016-17/34 dated 25.08.2016
Name of the Bidder:
Service Tax
Quantity Unit Labour rate Unit material
inclusive of all rate inclusive of @15%(Rs.)
all taxes &
taxes & duties
except Service duties except
VAT (Rs.)
Tax (Rs.)
Item
No.
Description
Unit
(1)
(2)
(3)
(4)
1.0
(5)
(6)
(7)
VAT @ %
(Rs.)
(8)
Total Unit Rate Total Amount
inclusive of all inclusive of all
taxes and
taxes and duties
duties including including VAT &
VAT & Service
Service Tax
Tax (Rs.)
(Rs.)
(9)=(5)+(6)+(7)+(
8)
(10)=(4) x (9)
SECTION-A : SS TUBE LAYING & TESTING
Laying, testing and commissioning of SS
tubes along with all fittings (i.e. unions,
reducers, elbows, Tees, Front Ferrule, Back
Ferrule, NRV etc.) (all free issue items) as per
Technical Specification & Typical P & ID for
type of CNG station and scope of work
including handling, lifting, transportation from
Company's Stores to CNG Stations
1.1
1” OD X 0.120” min Wall thk. SS Tube (Refer TS
Section III - A)
RM
1024
1.2
¾” OD X 0.095” min Wall thk. SS Tube (Refer TS
Section III - A)
RM
3573
1.3
½” OD X 0.083” min Wall thk. SS Tube (Refer TS
Section III - A)
RM
396
1.4
Erection rates of following items (Refer TS Section
III - A)
1.4.1 Ball Valves ¾” Size
No.
200
1.4.2 Ball Valves ½” Size
No.
195
1.4.3 Ferrule Fittings 1” (if to be changed)
No.
32
1.4.4 Ferrule Fittings ¾” (if to be changed)
No.
77
1.4.5 Ferrule Fittings ½” (if to be changed)
No.
38
Page 1 of 8
SCHEDULE OF RATES (SOR) FOR WORKS CONTRACT TENDER FOR MECHANICAL WORKS IN CNG STATIONS AT PUNE
Part - IV
Tender No.: MNGL/C&P/2016-17/34 dated 25.08.2016
Name of the Bidder:
Service Tax
Quantity Unit Labour rate Unit material
inclusive of all rate inclusive of @15%(Rs.)
all taxes &
taxes & duties
except Service duties except
VAT (Rs.)
Tax (Rs.)
Item
No.
Description
Unit
(1)
(2)
(3)
(4)
2.0
Dismantaling of SS tubes along with all
fittings (i.e. unions, reducers, elbows, Tees,
Front Ferrule, Back Ferrule, NRV, Valves etc.)
from the existing CNG station as per
Instruction from Engineer In-Charge and
scope of work including handling, lifting,
transportation and submitting to Company's
Stores from CNG site.
SS 316 tube of 3/4" OD/ 1/2" OD / SS 304 tube of
1/2" OD (Refer TS Section III - A)
RM
235
2.1
3.0
Supply, laying, testing and commissioning of
SS 304 Tubes along with isolation valves,
reducers & fittings etc.as per Technical
Specification, Typical schematic drg. for Ins.
air line of CNG station and scope of work
including
handling,
storage,lifting,
transportation upto CNG stations. (Note:Total
no.of ferrule fittings may be considered as
one jointing ferrule at every 5.0 m)
3.1
½” OD X 0.035” min Wall thk. SS Tube (Refer TS
Section III - A)
RM
1300
3.2
SS Ball Valves ½” Size
No.
93
3.3
Reducer ½” x 1/4" Size
No.
87
3.4
Euqal Tee ½" Size
No.
75
(5)
(6)
(7)
VAT @ %
(Rs.)
(8)
Total Unit Rate Total Amount
inclusive of all inclusive of all
taxes and
taxes and duties
duties including including VAT &
VAT & Service
Service Tax
Tax (Rs.)
(Rs.)
(9)=(5)+(6)+(7)+(
8)
(10)=(4) x (9)
Page 2 of 8
SCHEDULE OF RATES (SOR) FOR WORKS CONTRACT TENDER FOR MECHANICAL WORKS IN CNG STATIONS AT PUNE
Part - IV
Tender No.: MNGL/C&P/2016-17/34 dated 25.08.2016
Name of the Bidder:
Service Tax
Quantity Unit Labour rate Unit material
inclusive of all rate inclusive of @15%(Rs.)
all taxes &
taxes & duties
except Service duties except
VAT (Rs.)
Tax (Rs.)
Item
No.
Description
Unit
(1)
(2)
(3)
(4)
SECTION-B (i)
EQUIPMENT
:
ERECTION
OF
(5)
(6)
(7)
VAT @ %
(Rs.)
(8)
Total Unit Rate Total Amount
inclusive of all inclusive of all
taxes and
taxes and duties
duties including including VAT &
VAT & Service
Service Tax
Tax (Rs.)
(Rs.)
(9)=(5)+(6)+(7)+(
8)
(10)=(4) x (9)
MECH.
1.0
Handling (including lifting and transportation
from Company's store to CNG stations) and
erecting in position, the following equipment
either on the foundation at Ground level or on
roof at 3.5 m above ground level. Contractor's
scope shall include supply of all material and
accessories including but not limited to any
fixtures, clamps, gasket, nut bolts, etc.:
1.1
Cascade 4500 L water capacity. Erection at + 3.5
M level (Refer TS Section III - B)
No.
1
1.2
Cascade 3000 L water capacity. Erection at + 3.5
M level (Refer TS Section III - B)
No.
23
1.3
Cascade 2250 L water capacity, Erection upto +
3.5 M level (Refer TS Section III-B)
No.
6
Page 3 of 8
SCHEDULE OF RATES (SOR) FOR WORKS CONTRACT TENDER FOR MECHANICAL WORKS IN CNG STATIONS AT PUNE
Part - IV
Tender No.: MNGL/C&P/2016-17/34 dated 25.08.2016
Name of the Bidder:
Service Tax
Quantity Unit Labour rate Unit material
inclusive of all rate inclusive of @15%(Rs.)
all taxes &
taxes & duties
except Service duties except
VAT (Rs.)
Tax (Rs.)
Item
No.
Description
Unit
(1)
(2)
(3)
(4)
No.
4
SECTION-B
(ii)
:
TRANSPORTATION
&
MECHANICAL EQUIPMENT
(5)
(6)
(7)
VAT @ %
(Rs.)
(8)
Total Unit Rate Total Amount
inclusive of all inclusive of all
taxes and
taxes and duties
duties including including VAT &
VAT & Service
Service Tax
Tax (Rs.)
(Rs.)
(9)=(5)+(6)+(7)+(
8)
(10)=(4) x (9)
UNLOADING,
LOADING
OF
1.0
Unloading from existing position (including
Compressed natural Gas venting from cascade
if necessary), handling including lifting and
transportation
from
CNG
stations
to
Company's store / erecting on civil foundation
at or above ground level in other CNG stations
if required. Contractor's scope shall include
supply of all material and accessories
including but not limited to any fixtures,
clamps, gasket, nut bolts, etc. :
1.1
Cascade 2250 L water capacity, Erection upto +
3.5 M level (Refer TS Section III-B)
Page 4 of 8
SCHEDULE OF RATES (SOR) FOR WORKS CONTRACT TENDER FOR MECHANICAL WORKS IN CNG STATIONS AT PUNE
Part - IV
Tender No.: MNGL/C&P/2016-17/34 dated 25.08.2016
Name of the Bidder:
Service Tax
Quantity Unit Labour rate Unit material
inclusive of all rate inclusive of @15%(Rs.)
all taxes &
taxes & duties
except Service duties except
VAT (Rs.)
Tax (Rs.)
Item
No.
Description
Unit
(1)
(2)
(3)
(4)
No.
6
(5)
(6)
(7)
VAT @ %
(Rs.)
(8)
Total Unit Rate Total Amount
inclusive of all inclusive of all
taxes and
taxes and duties
duties including including VAT &
VAT & Service
Service Tax
Tax (Rs.)
(Rs.)
(9)=(5)+(6)+(7)+(
8)
(10)=(4) x (9)
SECTION-B (iii) : UNLOADING & LOADING OF
MECHANICAL EQUIPMENT (CASCADE)
1.0
Unloading from existing position (including
Compressed natural Gas venting from cascade
if necessary) at Ground level or on roof at 3.5
m above ground level, lifting & erecting on
foundation at ground level in the same CNG
stations. Again the same cascade is to be
shifted to new foundation within the same
CNG station. Contractor's scope shall include
supply of all material and accessories
including but not limited to any fixtures,
clamps, gasket, nut bolts, etc.
1.1
Cascade 2250 / 3000 L water capacity (Refer TS
Section III - B)
Page 5 of 8
SCHEDULE OF RATES (SOR) FOR WORKS CONTRACT TENDER FOR MECHANICAL WORKS IN CNG STATIONS AT PUNE
Part - IV
Tender No.: MNGL/C&P/2016-17/34 dated 25.08.2016
Name of the Bidder:
Service Tax
Quantity Unit Labour rate Unit material
inclusive of all rate inclusive of @15%(Rs.)
all taxes &
taxes & duties
except Service duties except
VAT (Rs.)
Tax (Rs.)
Item
No.
Description
Unit
(1)
(2)
(3)
(4)
No.
4
(5)
(6)
(7)
VAT @ %
(Rs.)
(8)
Total Unit Rate Total Amount
inclusive of all inclusive of all
taxes and
taxes and duties
duties including including VAT &
VAT & Service
Service Tax
Tax (Rs.)
(Rs.)
(9)=(5)+(6)+(7)+(
8)
(10)=(4) x (9)
SECTION-B
(iv)
:
UNLOADING,
TRANSPORTAION & LOADING OF BOOSTER
COMPRESSOR
1.0
Unloading from existing position (including
dismantaling of connection, packaging of
booster Compressor package), handling
including lifting and transportation from CNG
stations to Company's store / erecting on civil
foundation at or above ground level in other
CNG station site if necessary. Contractor's
scope shall include supply of all material and
accessories including but not limited to any
fixtures, clamps, wire rope, gasket, nut bolts,
etc. :
1.1
250 SCMH Hydraulic Booster Compressor (Refer
TS Section III - B)
Page 6 of 8
SCHEDULE OF RATES (SOR) FOR WORKS CONTRACT TENDER FOR MECHANICAL WORKS IN CNG STATIONS AT PUNE
Part - IV
Tender No.: MNGL/C&P/2016-17/34 dated 25.08.2016
Name of the Bidder:
Service Tax
Quantity Unit Labour rate Unit material
inclusive of all rate inclusive of @15%(Rs.)
all taxes &
taxes & duties
except Service duties except
VAT (Rs.)
Tax (Rs.)
Item
No.
Description
Unit
(1)
(2)
(3)
(4)
No.
1
1.2.1 DCP -75 Kg
No.
8
1.2.2 DCP -9 Kg
No.
32
1.2.3 CO2 – 4.5 Kg
No.
5
1.2.4 Sand Bucket Set (6 Nos. on each stand)
No.
7
(5)
(6)
(7)
VAT @ %
(Rs.)
(8)
Total Unit Rate Total Amount
inclusive of all inclusive of all
taxes and
taxes and duties
duties including including VAT &
VAT & Service
Service Tax
Tax (Rs.)
(Rs.)
(9)=(5)+(6)+(7)+(
8)
(10)=(4) x (9)
SECTION - C : SUPPLY, ERECTION &
COMMISSIONING OF MISCELLANEOUS ITEM
1.0
Supply, erection & commissioning of
following miscellaneous items as per technical
specification and at locations (within the
stations) as directed by EIC
1.1
Water cooler (Refer TS Section III - C)
1.2
Fire fighting Equipments (Refer TS Section III - C)
Page 7 of 8
SCHEDULE OF RATES (SOR) FOR WORKS CONTRACT TENDER FOR MECHANICAL WORKS IN CNG STATIONS AT PUNE
Part - IV
Tender No.: MNGL/C&P/2016-17/34 dated 25.08.2016
Name of the Bidder:
Service Tax
Quantity Unit Labour rate Unit material
inclusive of all rate inclusive of @15%(Rs.)
all taxes &
taxes & duties
except Service duties except
VAT (Rs.)
Tax (Rs.)
Item
No.
Description
Unit
(1)
(2)
(3)
(4)
(5)
(6)
(7)
VAT @ %
(Rs.)
(8)
Total Unit Rate Total Amount
inclusive of all inclusive of all
taxes and
taxes and duties
duties including including VAT &
VAT & Service
Service Tax
Tax (Rs.)
(Rs.)
(9)=(5)+(6)+(7)+(
8)
(10)=(4) x (9)
SECTION - D : FABRICATION OF CANOPY &
LOCALISED SHED FOR AIR COMPRESSOR
1.1
Supply & Installation of Canopy on Dispenser
(Size 13.5' x 13.5' x 12')
No.
10
1.2
Supply & Installation of Canopy on Air
Compressor (Size 12' x 10' x 10')
No.
10
Note: The quantities given above against
individual items are indicative and shall not be
considered to be binding. The quantities may
increase or decrease at site at the time of actual
execution and as per the discretion of Owner/
Engineer-in-charge. The unit rate shall be
operated to work out the final payment due to
Contractor.
Total Amount inclusive of all Taxes & Duties (in Rs.) (in Figure)
Total Amount inclusive of all Taxes & Duties (in Rs.)
(in Words)
Note:
1
2
3
4
The quantities of individual item can vary as per site requirement. The payment will be made as per actual certified measurement at site only.
For Item to be procured by Contractor, prior approval has to be taken from Engineer-in-charge.
All SOR item shall be quoted by the bidder in the price part of the bid other-wise bid will be rejected.
Prices quoted shall be inclusive of all taxes/duties and nothing extra shall be payble by the owner except for statutory variation in VAT &
Service Tax rate.
Place : _________________
Signature of Authorised Signatory
Date : _________________
Name :
Designation :
Seal :
Page 8 of 8
Download