Installation Guide for EcoBrite™ LED Light Fixtures BEFORE YOU BEGIN INSTALLATION Read these instructions carefully. Failure to follow these instructions will invalidate the warranty on this product. WARNING CAUTION Risk of electrical shock. Disconnect power Use caution when handling a power tool. Always wear protective eyewear. before installing or servicing product. 1 EcoBrite Installation Guide, Rev. 2.2, Date: 04/09/10 Thank you for purchasing our EcoBrite™ LED Light Fixtures. Please read the instructions completely before installation. Refer to page 7 for information regarding our warranty. Required tools and components 1.
2.
3.
4.
5.
6.
7.
8.
#8 x 1/2” sheet metal screws (4) ‐pan head or hex head Tape measure Pencil Drill Phillips screw bit or screwdriver 1/8” drill bit Regulated 12VDC Class 2 Power Supply (PN 750‐9990) Wire nuts or appropriate wire connectors Included Parts
EcoBrite™ Light Fixture (PN 750/1‐XXXX, 760/1‐XXXX) EcoBrite™ Mounting Clips (PN 750‐9910) Accessories EcoBrite™ 15 degree Mounting Shim (PN 750‐9911) Vertical Installation: 1.
Use a pencil to mark the pilot holes on mounting surface. See the drawing at the right and chart below to determine the hole spacing for the light you are installing. Allow at least 4 inches above the top mounting hole for the top end of the light and wiring. Two mounting clips are required for all lengths of EcoBrite™ lights. An optional center mounting clip may be installed when mounting 5 and 6 foot lights. Only one screw is necessary for each clip but optional 2nd pilot hole mark may be made ½ inch below the first mark if two mounting screws are used to fasten the mounting clips. Note: Prior to drilling, ensure that there are no components behind the mounting surface in the areas marked off for the designated holes
EcoBrite™ Light Length (feet) Recommended Distance “A” Recommended Distance “B” 1 2 3 4 5 6 9 19
29 40 50 60 Not needed Not needed
Not needed
20 (Optional) 25 (Optional) 30 (Optional) 2 EcoBrite Installation Guide, Rev. 2.2, Date: 04/09/10 2.
3.
4.
Drill a 1/8” diameter pilot hole into the mounting surface at each of the marks made in step 1. Fasten the clips to the surface with a #8 sheet metal screws. Snap the back side of the EcoBrite™ light into the mounting clips. 5.
Connect to a Regulated, 12V DC, Class 2 power supply to operate. See page 4 for wiring information. Tilted Installation: EcoBrite™ Mounting Shims may be used to securely install the EcoBrite™ light in a tilted orientation. To install the EcoBrite™ light with mounting shims, follow the standard horizontal or vertical installation instructions 1 and 2, but drill two pilot holes ½ inch apart for each clip used. In step 3, place the mounting shim behind the mounting clip as shown in the image at the right. Then, fasten both parts to the mounting surface with two screws. Fasten the remaining mounting shims and clips to the mounting surface. Continue with the rest of the standard installation instructions. 3 EcoBrite Installation Guide, Rev. 2.2, Date: 04/09/10 Wiring Information: EcoBrite™ lights must be connected to a Regulated, 12V DC, Class 2 power supply to operate using wire nuts or appropriate wire connectors. Red Wire ‐ Connect to (+) positive output of the 12V DC power supply. Green/Yellow wire ‐ Connect to (‐) negative output of the 12V DC power supply. Optional Dimming Control: Connect the Blue wire to the output of a “Normally Closed” isolated relay controlled by an occupancy sensor. Connect the input of this relay to the (+) positive output of the 12V DC power supply. The light is dimmed when the blue wire receives +12V DC with respect to the green/yellow wire. Protect wire end with a wire nut if not in use. All wiring must be in compliance with NEC and local codes. This light fixture is suitable for damp locations. When used in a damp location, ensure that all connection points are sealed for damp location using the appropriate method per the NEC or local electrical code. Removal Information If you need to remove the light fixture, place a slotted screwdriver between the rail and the side of the clip. Gently press the screwdriver handle towards the light to release the light. Do this for all clips. Refer to the image at the right. 4 EcoBrite Installation Guide, Rev. 2.2, Date: 04/09/10 Cleaning If the EcoBrite™ lights require cleaning, follow the procedure bellow. ‐ Switch off or disconnect the power to the EcoBrite™ lights. ‐ Remove the EcoBrite™ lights from the mounting clips if necessary. ‐ Wipe surfaces with a clean, soft cloth lightly dampened in a mixture of warm water and mild dish soap. ‐ Wipe surfaces again with a clean, soft cloth lightly dampened in warm water. ‐ Dry all surfaces completely with a clean, soft cloth. ‐ Reattach the lamp to the mounting clips and switch on/reconnect power. Do not use abrasive cleaners, scouring pads, or paper towels to clean or dry the lamp. Do not use bleach, alcohol, or other chemicals to clean the lamp. Some chemicals and abrasive products may scratch and damage the surfaces. Do not submerge the lamp or use overly wet cloths as it may cause damage to internal electrical components. 5 EcoBrite Installation Guide, Rev. 2.2, Date: 04/09/10 6 EcoBrite Installation Guide, Rev. 2.2, Date: 04/09/10 Purchase Date: ________________________ Warranty Expiration Date: _______________ Thank you for your purchase of EcoBrite™ LED Light Fixtures. Please keep the top portion of this page for your records and mail the bottom portion to the address provided to register your product. WARRANTY INFORMATION Innovative Lighting Inc. (ILC) Limited Product Warranty is FIVE (5) YEARS from date of purchase on EcoBrite™ LED Light Fixtures and their components. Any product developing such defect in material or workmanship within this period will be repaired or replaced with a like product, at our option (ILC) providing it is sent to us, transportation charges prepaid. Proof‐of‐Purchase date must accompany return to ILC at our Roland, Iowa facility. ILC does not warrant contractor’s installation work or performance. This warranty is void if the product warranted has been damaged by accident or unreasonable use, neglect, improper installation or service, or other cause not arising out of defects in material or workmanship. This FIVE (5) YEAR limited product warranty is not transferable and applies to the original installation of the EcoBrite™ LED Lighting System for as long as the original purchaser owns them. SHIPPING DAMAGE EcoBrite™ LED Light Fixtures should be examined for shipping damage upon receipt. These fixtures have been carefully inspected before shipment. Any claim for loss or damage must be made to the carrier. The carrier will provide any necessary inspection reports and/or claim forms. PRODUCT REGISTRATION PRODUCT INFORMATION EcoBrite™ LED Light Fixture Model: _______________ EcoBrite™ LED Light Fixture Date Code: ____________ Date of Purchase: _______ Number of units purchased:_______ OWNER INFORMATION Name: _________________________________________ Company: ______________________________________ Address: _______________________________________ City: __________________________________________ State: ___________________________ Zip: __________ Phone: _________________________________________ Fax: ___________________________________________ E‐mail: ________________________________________ Mail to: Innovative Lighting, Inc., P.O. Box 366, Roland, Iowa 50236 7 EcoBrite Installation Guide, Rev. 2.2, Date: 04/09/10