LINCOLNWELD WTX & WTX-TR
SUBMERGED ARC (SAW) WELDING FLUX
Accuracy and
Consistency
At a High Level
If you’re building wind towers, precision is crucial. Get the most
consistent and quantifiable welds – on time and on budget –
with WTX™ fluxes. Designed for submerged-arc welding with
Lincolnweld® L-61® wire, and engineered to pass a broad range
of testing standards, WTX fluxes deliver a high level of quality
and far surpass all mechanical properties requirements of the
industry. WTX fluxes are low hydrogen, right out of the bag. No
need for conditioning, which means less risk of hydrogen failures.
Just open the bag and use it. Choose WTX for multi-pass welding
and WTX-TR for extensive two-run work.
• Consistent bead shape and appearance results in better looking welds
• WTX optimized for multi-pass welding and excellent slag removal
• Two-run toughness with WTX-TR far exceeds competitive fluxes
Lower Diffusible Hydrogen
8
7
mL/100g weld metal
Diffusible
Hydrogen Levels
6
5
8.0
4
3
2
3.4
4.0
Diffusible hydrogen increases the risk of weld cracking and
failure. Lincolnweld WTX-TR and WTX when used with
Lincolnweld L-61 electrodes produce welds with an average
of 3mL/100g weld metal of diffusible hydrogen. This is 50%
less than our competitor’s received flux, and Lincoln Electric
does it with no baking required, saving you time and money.
1
0
Multi-run Application
Lincolnweld
WTX
Lincolnweld
WTX-TR
ESAB®
OK Flux 10.72™
Our wind tower fluxes are designed for optimal performance
in both 2-run and multi-run applications. Choose WTX for
multi-pass applications where toughness exceeds 80 ft-lb
@ -80°F, and choose WTX-TR in two run applications where
toughness exceeds 130 ft-lb @ -40°F.
ft. · lbf. @ -80°F
100
75
50
84
ft. · lbf. @ -80°F
25
32
ft. · lbf. @ -80°F
0
Two-Run Application
Lincolnweld
WTX
ESAB
OK Flux 10.72
160
ft. · lbf. @ -40°F
140
120
100
80
60
132
ft. · lbf. @ -40°F
40
20
0
Better Toughness
21
ft. · lbf. @ -40°F
Lincolnweld
WTX-TR
ESAB
OK Flux 10.72
PACKAGING
Product Name
50 lb (22.7 kg) Plastic Bag
2200 lb (998 kg) Bulk Bag
Lincolnweld WTX
ED032990
ED033903
Lincolnweld WTX-TR
ED035463
ED035845
MECHANICAL PROPERTIES FLUX(1)/ WIRE COMBINATION
Charpy V-Notch
AWS Classification
Yield Strength
MPa (ksi)
Tensile Strength
MPa (ksi)
Elongation
%
J (ft•lbf)
@°C (°F)
Lincolnweld WTX/ L-61
F7A8-EM12K-H8
400 (58)
510 (74)
29
143 (106)
-62 (-80)
Lincolnweld WTX/L-70
F8A4-EA1-A3-H8
470 (68)
570 (83)
25
58 (43)
-40 (-40)
Multi-Pass
MECHANICAL PROPERTIES FLUX(1)/ WIRE COMBINATION
Charpy V-Notch
Two-Run
AWS Classification
Yield Strength
MPa (ksi)
Tensile Strength
MPa (ksi)
Elongation
%
J (ft•lbf)
@°C (°F)
Lincolnweld WTX-TR/L-61
F7TA4-EM12K-H8
560 (81)
640 (93)
23
160 (118)
-40 (-40)
FLUX COMPOSITION
%SiO₂
%MnO
%MgO
%CaF₂
%Na₂O
%Al2O3
%CaO
%ZrO₂
%FeO
%K2O
%TiO2
Lincolnweld WTX
21
9
23
13
2
25
5
1
2
1
1
Lincolnweld WTX-TR
17
18
22
13
2
25
4
2
3
1
3
PRODUCT INFORMATION
Product Name
(1)
Basicity Index
Density
Lincolnweld WTX
1.4
1.2
Lincolnweld WTX-TR
1.5
1.2
See test results disclaimer on back page. ESAB® and ATOM ARC™ are a registered trademarks of ESAB Welding & Cutting Products.
TES T R ES U LTS
Test results for mechanical properties, deposit or electrode composition and diffusible hydrogen levels were obtained from a weld produced and tested according to prescribed standards, and should not be assumed to be the expected results in a particular application or weldment.
Actual results will vary depending on many factors, including, but not limited to, weld procedure, plate chemistry and temperature, weldment design and fabrication methods. Users are cautioned to confirm by qualification testing, or other appropriate means, the suitability of any
welding consumable and procedure before use in the intended application.
C U S TO M E R A S S I S TA N C E P O L I C Y
The business of The Lincoln Electric Company is manufacturing and selling high quality welding equipment, consumables, and cutting equipment. Our challenge is to meet the needs of our customers and to exceed their expectations. On occasion, purchasers may ask Lincoln Electric for information
or advice about their use of our products. Our employees respond to inquiries to the best of their ability based on information provided to them by the customers and the knowledge they may have concerning the application. Our employees, however, are not in a position to verify the information
provided or to evaluate the engineering requirements for the particular weldment. Accordingly, Lincoln Electric does not warrant or guarantee or assume any liability with respect to such information or advice. Moreover, the provision of such information or advice does not create, expand, or alter
any warranty on our products. Any express or implied warranty that might arise from the information or advice, including any implied warranty of merchantability or any warranty of fitness for any customers’ particular purpose is specifically disclaimed.
Lincoln Electric is a responsive manufacturer, but the selection and use of specific products sold by Lincoln Electric is solely within the control of, and remains the sole responsibility of the customer. Many variables beyond the control of Lincoln Electric affect the results obtained in applying these
types of fabrication methods and service requirements.
Subject to Change – This information is accurate to the best of our knowledge at the time of printing. Please refer to www.lincolnelectric.com for any updated information.
Publication C5.10.43b | Issue Date 04/15
© Lincoln Global, Inc. All Rights Reserved.
www.lincolnelectric.com
The Lincoln Electric Company
22801 St. Clair Avenue
Cleveland, OH 44117-1199 U.S.A.