MODUL hinges
MODUL general specifications
Hinge-to-door attachment
Mounting plate-to-cabinet
Screw-on
Press-in
Use #6 wood screws
Pre-attached dowels,
install with Blum MINIPRESS
Screw-on
Blum boring pattern
C
9.5
B
Door
35
Ø
45
Ø8
Door-to-cabinet attachment
C Cup centerpoint
20.5 21.5 22.5 23.5 24.5 25.5
13/16" 27/32" 7/8" 15/16" 31/32" 1"
3
4
5
6
7*
8*
B Bore distance
To install slide hinge on
to the mounting plate,
tighten rear fixing screw.
Loosen rear fixing screw
and pull hinge forward to
remove.
* only for use with select Blum hinges
Cup centerpoint is the MINIPRESS or MINIDRILL fence depth position.
Three-dimensional adjustment
Side adjustment
Height adjustment
Loosen screw(s) on the mounting plate.
Adjust door to position and tighten screws.
Range = ±3 mm
Loosen back screw. Adjust door to position
and tighten screw.
Range = ±2 mm
Two piece mounting plate
One piece mounting plate
Hinge dimension abbreviations
H
Minimum reveal
Hinges per door
S
W
X = Door height
100"
Y = Number of hinges
45-60
lb.
80"
1 rad
(1/32")
B
H
OL
P
R
B
OL
= Boring distance
= Mounting plate height
= Door overlay
= Door protrusion
(at max opening)
P
19
X
T
MODUL
Rotate front screw to increase or decrease
door overlay.
Range = ±2 mm
Depth adjustment
Minimum Reveal
R
S
T
W
X
= Reveal
= Hinge arm protrusion
= Door thickness
= Side panel width
= Fixed cup distance
A minimum reveal per door is required to keep the door
from binding and varies depending on door thickness
(see Minimum reveal table for each hinge). Minimum
reveal based on outside door edge with radius of 1 (1/32").
30-45
lb.
This chart can serve
as a guide for deter- 60"
mining the number
of hinges per door. 40"
Note that door weight
can also determine 20"
the number of hinges
X
required.
15-30
lb.
15
lb.
Y
2
*
3
4
5
* The distance between the top and bottom hinges must
be greater than the width of the door.
For more information on using this section see page 5.
All dimensions in millimeters (inch equivalents as shown).
53
Subject to technical modifications without notice. © 2010
MODUL 100˚ hinges
100˚
Features
Minimum Reveal
- 100˚ opening angle
- All metal hinge, nickel-plated
- Three-dimensional adjustment
- Slide-on hinge arm
Cover caps
Mounting plates
Frame cabinet applications
Overlay door
Minimum reveal table
page 59
pages 57-58
0.5
0.9
1.1
1.4
2.3
3.6
5.2
3
0.5
0.8
1.0
1.3
2.0
3.3
4.8
4
0.4
0.8
1.0
1.2
1.8
3.0
4.4
5
0.4
0.8
0.9
1.1
1.7
2.8
4.1
6
16
18
19
20
22
24
26
B
T Door thickness
Bore
Cross-reference the door
thickness and
bore distance
to assure that
doors won’t
bind when
opened.
See back cover fold out for more specifications
Panel cabinet applications
Straight-arm hinges
Overlay door
Self close
H
Screw-on
H
11
Press-in
Free swing
91M2550
90M2550
91M2580
90M2580
T
T
37
58
58
Overlay table
B
10.5
10.5
B
Overlay
0
14
15
16
17
9
20
3
11
12
13
14
12
23
6
8
9
10
11
15
26
9
5
6
7
8
18
29
H
3
4
5
6
P
S
Plate
Overlay
Clearances
B Bore distance
11 fixed distance
Partial overlay door
Half-cranked hinges (9.5 mm)
Twin overlay doors
Self close
91M2650
Screw-on
H
91M2680
11
Press-in
H
58
58
Overlay table
0
4.5
5.5
6.5
H
3
4
5
37
Plate
Partial overlay
7.5 18.5 30
6
10.5
Reveal
Overlay
0
H
Twin overlay
7
5
3
1
10
8
6
4
19
13
11
9
7
22
4
5
6
3
Plate
16
18.5 30
W
P
Self close
H
91M2750
Screw-on
Press-in
91M2780
11
T
T + 38.5
60
Reveal table
0
4
3
2
1
27
38
H
3
4
5
6
P
S
Plate
B Bore distance
10.5
- 7 fixed distance
B
Reveal
For more information on using this section see page 5.
All dimensions in millimeters (inch equivalents as shown).
54
S
Panel Clearances
B Bore distance
Full-cranked hinges (18 mm)
Inset door
Subject to technical modifications without notice. © 2010
S
1.5 fixed distance
T
T
10.5
B
P
Clearances
B Bore distance
Reveal table
B
MODUL
NOTE: 9 plate only available for panel cabinets
Clearances
MODUL 170˚ hinges
170˚
Features
Minimum Reveal
- 170˚ opening angle
- All metal hinge, nickel-plated
- Three-dimensional adjustment
- Slide-on hinge arm
Minimum reveal table
Cover caps
Mounting plates
page 59
pages 57-58
0
0
0
0
0.2
2.2
4.2
3
0
0
0
0
0
1.4
3.8
4
0
0
0
0
0
.9
2.7
5
0
0
0
0
0
0
2.2
6
0
0
0
0
0
0
1.7
7
0
0
0
0
0
0
1.3
8
16
18
19
20
22
24
26
B
T Door thickness
Frame cabinet applications
Overlay door
Cross-reference the door
thickness and
bore distance
to assure that
doors won’t
bind when
opened.
Bore
See back cover fold out for more specifications
Panel cabinet applications
Straight-arm hinges
Overlay door
Self close
H
91A6550
Screw-on
W
H
18
Press-in
91A6580
T
T
37
69
69
Overlay table
B
11
11
B
Overlay
0
14
15
16
17
18
19
1.5
65
3
11
12
13
14
15
16
4.5
68
7.5
71
6
8
9
10
11
12
13
9
5
6
7
8
9
10 10.5 74
H
3
4
5
6
7
8
Plate
P
S
Clearances
B Bore distance
11 fixed distance
Overlay
NOTE: 9 plate only available for panel cabinets
Half-cranked hinges (9.5 mm)
Twin overlay doors
Self close
91A6650
Screw-on
W
H
H
18
Press-in
H
91A6680
37
69
69
Overlay table
4.5
5.5
6.5
7.5
8.5
9.5
11
75
H
3
4
5
6
7
8
P
S
Plate
Clearances
B Bore distance
1.5 fixed distance
Reveal table
B
11
B
Partial overlay
0
T
0
Reveal
Overlay
H
Twin overlay
7
5
3
1
-
-
16
10
8
6
4
2
0
19
13
11
9
7
5
3
22
3
4
5
6
7
8
Plate
W
11
75
P
S
Panel Clearances
B Bore distance
Half-cranked hinges (9.5 mm)
Inset door
Use half-cranked hinge
Any 9 mm plate
H
Self close
91A6650
Screw-on
18
Press-in
91A6680
T + 38.5
71
Reveal table
T
9
4.5
3.5
H
3
4
Plate
2.5 1 .5 0.5
5
6
B Bore distance
7
-
20
84
8
P
S
Clearances
- 7.5 fixed distance
B
11
11
T
MODUL
Partial overlay door
Reveal
For more information on using this section see page 5.
All dimensions in millimeters (inch equivalents as shown).
55
Subject to technical modifications without notice. © 2010
56
MODUL
MODUL mounting plates
One piece wing mounting plate
H
-
*
Cover caps
Mounting plates
pages 59-60
*
32
Steel, nickel-plated
Attached with wood screws #6 x 5/8"
Height adjustment ±3 mm
*Add additional
wood screw if used with wide angle hinges
page 61
37
Wood screws
(H) Height 0
606N or 606P
193L6100
-
8.5
H
One piece wing mounting plate
*
Steel, nickel-plated
Attached with pre-mounted system screws Ø5 mm (668.1450.EH)
Height adjustment ±3 mm
*Add additional wood screw if used with wide angled hinges
5
32
*
System screws
Pre-mounted
37
(H) Height 0
Two piece mounting plate
H
-
*
*
Zinc die-cast, nickel-plated
Attached with wood screws #6 x 5/8"
Height adjustment ±2 mm
*Add additional wood screw if used with wide angled hinges
32
MODUL
193L8100
37
Wood screws
(H) Height 0
(H) Height 9
606N or 606P
195H7100
195H7190
For more information on using this section see page 5.
All dimensions in millimeters (inch equivalents as shown).
57
Subject to technical modifications without notice. © 2010
MODUL mounting plates
H
11.5
Two piece wing mounting plate
*
5
Cover caps
Mounting plates
-
pages 59-60
32
*
Zinc die-cast, nickel-plated
Attached with #7 x 9/16" wood screw or Ø6 x 14.5 mm system screws
Height adjustment ±2 mm
*Add additional
screw if used with wide angle hinges
page wood
61
37
Wood screw or System screws
707N
661.1450.HG
(H) Height 0
195H9100
Face frame adapter plate
Zinc die-cast, nickel-plated
Attached with wood screws #7 x 3/4"
Height adjustment ±2 mm
Use of the PlateMate recommended for proper installation
(see page 78)
Wood screws
7074N
12.5
(H) Height 0
(H) Height 6
198.6600.22
198.6660.22
Recessed frame adapter plate
-
15
8.5
35
45
For more information on using this section see page 5.
All dimensions in millimeters (inch equivalents as shown).
Subject to technical modifications without notice. © 2010
Zinc die-cast, nickel-plated
Attached with wood screws #6 x 5/8"
Height and side adjustment ±2 mm
For overlays of 24 mm (15/16") to 27 mm (1-1/16")
58
Wood screw
(H) Height 0
606N or 606P
199.0100.02
MODUL
32
-
a
MODUL cover caps
Nylon (black or white)
90M2103
80.6107
90M2103.22
(Blum logo)
94M3203
MODUL cover caps
Nylon
MODUL 100˚ hinges
90M2103
94M3203
Straight-arm
Cranked-arm
MODUL 170˚ hinges
80.6107
MODUL Blind corner hinges
Straight-arm
90M2103
NOTE: Custom logo available in nylon (black or white). Consult your Blum representative for minimum quantities and lead times on custom logos.
MODUL
59
Subject to technical modifications without notice. © 2010