Installation Instructions IML6 / ILC6 6” LED Light

advertisement
1 of 2
Installation Instructions
IML6 / ilc6 6” LED Light Commercial Downlight
IS-R1000R1
Important safety instructions
–– Read all installation instructions before installing. It is important to save these instructions.
–– Observe and follow all label information and instructions regarding dry, damp and wet location listings, proper Intense LED module, warnings of installation near combustible materials
and/or insulation.
–– Turn off power at circuit breaker before attempting to install or perform maintenance on the fixtures.
–– Be sure to connect ground wire to prevent electric shock or other potential hazards.
–– The product must be installed in a manner consistent with the intended use and in compliance with the national electrical codes and local codes.
–– Do not block the trim aperture as this may cause unsafe operating conditions.
–– Warning: risk of fire. Non-IC fixture requires that insulation must be kept at least 3” away from all sides of the fixture. Minimum of 90°C supply conductors. Consult a qualified
electrician before installation.
Warning: Use only Intense Lighting trims listed for use with this fixture. Use of trims other than those listed by Intense Lighting is a violation of n.E.C 110-3(b) and voids all warranties.
Installation in new constructions
1. Locate fixture between joists (Fig. 1).
2. Extend bar hangers to fit between joists. Align bar hanger with the bottom of each joist and hammer nails into joists (Fig. 2).
3. Remove junction box cover plate. Remove desired knockout, the junction box will accept metal conduit or non-metallic cable.
4. Connect black wire from fixture to black (hot) supply wire, white wire from fixture to white (neutral) supply wire and connect the ground from fixture to green (ground) supply
wire. Use UL listed connectors or wire nuts to make the connections (not included) (Fig. 3).
5. Make connections in junction box and replace cover plate.
Fig. 1
Fig. 2
Fig. 3
Black
Joist
Align bottom
of bar hanger
to joist
Ceiling Line
White
Green
Junction box
cover plate
Hammer all four
nails into joist
Installation in T-BAR ceilings
1. Cut appropriately sized hole in ceiling tile at the position desired and place ceiling tile in grid (Fig. 4).
2. Place frame on top of ceiling tile perpendicular to ceiling grid and extend bar hangers over T-bar grid with notch (Fig. 5).
3. Remove junction box cover plate. Remove desired knockout, the junction box will accept metal conduit or non-metallic cable.
4. Connect black wire from fixture to black (hot) supply wire, white wire from fixture to white (neutral) supply wire and connect the ground from fixture to green (ground) supply
wire. Use UL listed connectors or wire nuts to make the connections (not included) (Fig. 6).
5. Make connections in junction box and replace cover plate.
Fig. 4
Fig. 6
Fig. 5
Black
White
Green
Junction box
cover plate
led Module installation
1. Place female quick connect from housing through frame-in aperture (Fig. 7).
2. Lift locking feature on female quick connect and insert male connect from reflector, then lock connection with locking feature (Fig. 8)
3. Push LED module and reflector into frame-in aperture ensuring the trim is flush to the ceiling (Fig. 9).
4. Once all fixtures have been installed, power at the breaker can be restored.
Fig. 7
Fig. 8
Female Quick Connect
Male Quick Connect
Fig. 9
Locking
Feature
INSTRUCTIONS L/M-09132013 P-16
Intense Lighting | 2861. E La Palma Ave. | Anaheim, CA 92806 | Phone: 1.800.961.5321 | Fax: 1.800.961.5322 | www.intenselighting.com
Note: Instructions and dimensions subject to change without notice.
2 of 2
INTENSE LIGHTING WARRANTY
INTERIOR LED PRODUCTS: 10-YEAR LIMITED WARRANTY
Intense Lighting warrants the LED electronics and components of its properly installed INTERIOR LED products
listed below, to be free of defects in material and workmanship in normal use, for a period of 10 years from the
date of our shipment or 50,000 hours of operation, whichever occurs first. Intense Lighting will repair or replace,
at its option, any warranted product returned to it that it determines to be defective. Usage documentation may
be requested to validate hours. This limited warranty does not include installation or removal, nor does it extend
to the LED drivers which are warranted for five years. For the first year after the date of shipment, Intense Lighting
will provide personnel to make field repairs for defective recessed fixtures only. Track fixtures must be sent back to
factory for testing and evaluation. In addition to complete failure, defects include lumen depreciation to levels below
70% of initial lumen output within warranty period and/or color shift beyond that which is set forth in the Energy Star
Program Requirements for SSL – Version 1.1 within warranty period.
Defects do not include improper installation or operation, alterations, power surges or overheating due to external
conditions. To receive credit for defective merchandise, product must undergo quality inspection prior to the
processing of credit. If the product is found defective, you will be issued a credit. Product in good working condition
will not receive a credit. Please inform your accounting department not to short pay or issue any debits to our
company regarding a return. Testing and evaluation can take approximately 1-2 weeks based on quantity. At that
time you will be notified if credit is granted for your warranty return.
THE ABOVE EXPRESS WARRANTY STATES THE FULL AND COMPLETE OBLIGATION OF INTENSE LIGHTING. ALL
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE LIMITED IN DURATION
TO THE TERM OF THE EXPRESS WARRANTY. UNDER NO CIRCUMSTANCES WILL INTENSE LIGHTING ACCEPT LIABILITY
FOR ANY CONSEQUENTIAL SPECIAL OR INDIRECT DAMAGES WHETHER ARISING OUT OF CONTRACT, TORT, OR
STRICT LIABILITY.
INSTRUCTIONS L/M-09132013 P-17
Intense Lighting | 2861. E La Palma Ave. | Anaheim, CA 92806 | Phone: 1.800.961.5321 | Fax: 1.800.961.5322 | www.intenselighting.com
Note: Instructions and dimensions subject to change without notice.
Download