copertina 4 finale.indd
advertisement
4.1 CSA-CAT-11 Intrusion System Components Cooper CSA srl • Toll Free Number 800.449433 • www.coopercsa.it Pictorial Index Micro contacts Surface-mounting magnetic contacts Long-distance magnetic contact IP 65 Series 1005 N page 26 Brass flush-mounting micro contact Series 314 page 6 Thermoplastic magnetic contact with terminals - Series 400 page 15 Aluminium surfacemounting micro contact - Series 355 page 7 Thermoplastic magnetic contact Series 403 page 16 Concealed magnetic contacts Compact metal magnetic contact Series 403 AP page 17 Indoor high-security magnetic contact Series 1000 page 30 Metal magnetic contact Series 403 AG page 18 High-security magnetic contact IP 65 Series 1000 N pag. 30 Flush-mounting high-security magnetic contact Series 1050 page 19 Flush-mounting high-security magnetic contact - Series 1050 page 31 Brass cylindrical magnetic contact Series 414 page 9 Flush or surfacemounting magnetic contact - Series 410 page 20 High-security magnetic contact IP 65 Series 1100 page 32 Brass cylindrical short magnetic contact Series 414 C page 10 Magnetic contact for garage doors Series 450 page 21 Thermoplastic cylindrical magnetic contact - Series 415 Magnetic contact for garage doors Series 450 N page 22 Concealed magnetic contacts - Series 401 page 8 Flush-mounting magnetic contacts page 11 Flush-mounting magnetic contact Series 416 page 12 Aluminium power magnetic contact Series 460 page 23 High-power magnetic contact Series 1105 page 27 High-security magnetic contacts Inertia and vibration sensors Mercury vibration sensor Series 443 page 33 Inertia sensor Series 444 page 34 Magnetic contact for armoured doors Series 423 page 13 Aluminium magnetic contact Series 460 N page 24 Inertia sensor in self-protected housing Series 446 page 35 Magnetic contact for armoured doors Series 424 page 14 Long-distance magnetic contact Series 1005 page 25 Piezoelectric contact Series 447 page 36 Pictorial Index Hammer inertia sensor Series 1440 Panic button 476 page 37 page 48 IP 65 aluminium inertia sensor Series 1447 Foot pressure mat 482 / 483 page 38 page 49 Piezoelectric detector with memory 2152 Anti-burglary button Series 484 page 39 Contacts for roller shutters Magnetic contact for roller shutters 455 page 41 Rod contact for roller shutters 470 page 50 Security key locks 491-T 496-CSA 496-I page 57 497-5K 497-I-5K 497-SBC-19 497-SBC-23 Foot-operating button Series 485 page 58 page 51 497-I-SBC-19 497-I-SBC-23 498-CSA 498-1512 499-CSA Heat and flooding detectors Multifunction detector FIRECAT page 59 Power supply units page 42 page 52 Rope contact for roller shutters 471 Switching 13,8 Vdc power supply unit Series 81000 S page 43 Flooding and moisture detector Series 1450 page 53 Rope magnetic contact for roller shutters Series 473 IP 65 flooding detector IP 65 Series 2450-N page 44 page 54 Metallic box 13,8 Vdc switching power supply unit Series 81000 SB page 61 Junction boxes and auxiliary circuits 1463-CSA 1463-FR 1465-CSA 1467-FR page 46 Anti-burglary security devices Anti-burglary reed button Series 457 page 47 Sounders and beacons Sounder with beacon ASSERTA MINI page 55 2460-B 3465-12-BIANCA 587011FULL-0110X 531044FULL-1003 page 56 page 60 Electromagnetic door holders Flush mounting power door holders Series1385 page 62 Surface-mounting power door holders Series 1390 page 63 Micro contacts Concealed magnetic contacts Flush-mounting magnetic contacts Surface-mounting magnetic contacts Series 314 Series 355 Series 401 Series 414 Series 414 C Series 415 Series 416 Series 423 Series 424 Company profile Brass flush-mounting micro contact Aluminium surface-mounting micro contact Concealed magnetic contact Brass cylindrical magnetic contact Brass cylindrical short magnetic contact Thermoplastic cylindrical magnetic contact Flush-mounting magnetic contact Magnetic contact for armoured doors Magnetic contact for armoured doors page 4 page 6 page 7 page 8 page 9 page 10 page 11 page 12 page 13 page 14 Series 400 Thermoplastic magnetic contact with terminals page 15 Thermoplastic magnetic contact Compact metal magnetic contact Compact metal magnetic contact Thermoplastic magnetic contact Flush or surface-mounting magnetic contact Magnetic contact for garage doors Magnetic contact for garage doors Aluminium power magnetic contact Aluminium magnetic contact Long-distance magnetic contact Long-distance IP 65 magnetic contact High-power magnetic contact Accessories for surface-mounting magnetic contacts Series 1000 High-security magnetic contacts Indoor high-security magnetic contact Series 1000 N IP 65 high-security magnetic contact Series 1050 Flush-mounting high-security magnetic contact Series 1100 IP 65 high-security magnetic contact 443 Inertia and vibration sensors Mercury vibration sensor 444 Inertia sensor Series 446 Inertia sensor in self-protected housing Series 447 Piezoelectric sensor 1440 Hammer inertia sensor Series 1447 IP 65 aluminium inertia sensor 2152 Piezoelectric detector with memory Accessories for inertia and vibration sensors 455 Contacts for roller shutters Magnetic contact for roller shutters 470 Rod contact for roller shutters 471 Rope contact for roller shutters Series 473 Rod magnetic contact for roller shutters Accessories for roller shutters Junction boxes and auxiliary circuits 1463-CSA / 1463-FR / 1465-CSA / 1467-FR Series 457 Security devices anti-burglary Anti-burglary reed button 476 Anti-panic button 482 / 483 Foot pressure mat Series 484 Anti-burglary button Series 485 Foot-operating button FIRECAT Heat and flooding detectors Multifunction detector Series 1450 Flooding and moisture detector Series 2450 N IP 65 flooding detector ASSERTA MINI Sounder with beacon Sounders and beacons 2460-B / 3465-12-BIANCA / 587011FULL-0110X / 531044FULL-1003 Series 491, 496 491-T / 496-CSA / 496-I Security key locks Series 497 497-5K / 497-I-5K / 497-SBC-19 / 497-SBC-23 Series 497, 498, 497-I-SBC-19 / 497-I-SBC-23 / 498-CSA / 498-1512 / 499-CSA 499 Series 81000 S Switching 13,8 Vcc power supply unit Power supply units Series 81000 Metallic box 13,8 Vcc power supply unit SB 1385 Electromagnet door holders Flush-mounting electromagnetic door holders Series 1390 Surface-mounting electromagnetic door holders Accessories for electromagnet door holders Technical specifications General terms of business Series 403 Series 403 AP Series 403 AG Series 405 Series 410 Series 450 Series 450 N Series 460 Series 460 N Series 1005 Contents Series 1005 N Series 1105 The manufacturer reserves the right to modify the contents of this catalogue without notice page 16 page 17 page 18 page 19 page 20 page 21 page 22 page 23 page 24 page 25 page 26 page 27 page 28 page 29 page 30 page 31 page 32 page 33 page 34 page 35 page 36 page 37 page 38 page 39 page 40 page 41 page 42 page 43 page 44 page 45 page 46 page 47 page 48 page 49 page 50 page 51 page 52 page 53 page 54 page 55 page 56 page 57 page 58 page 59 page 60 page 61 page 62 page 63 page 64 page 66 page 71 Index by product code CODE PAGE CODE PAGE CODE PAGE CODE PAGE 1001-CSA 29 300-K-STL 64 424-TF 14 484-I 50 1001-N 30 300-K-STU-E 64 443-CSA 33 484-ME 50 1003-CSA 29 300-K-STZ 65 444-CSA 34 485-I 51 1003-M 29 300-MA 6 446-AN 35 485-ME 51 1003-N 30 314-CSA 6 446-AVR 35 491-T 57 1005-CSA 25 314-N 6 447-B 36 496-CSA 57 1005-N 26 3465-12-BIANCA 56 447-C 36 496-I 57 1021-CSA 29 355-CSA 7 447-CM 36 497-5K 58 1021-N 30 400001FULL-0001 52 447-IP65 36 497-I-5K 58 1031-N 30 400-FR 15 447-M 36 497-I-SBC-19 59 1035-N 26 401-TF 8 448-CSA 40 497-I-SBC-23 59 1051-CSA 31 401-TF-3 8 450-CSA 21 497-SBC-19 58 1101-CSA 32 401-TF-M 8 450-FR 21 497-SBC-23 58 1103-CSA 32 401-TF-M-3 8 450-N 22 498-1512 59 1105-CSA 27 403-AG 18 450-TF-2 21 498-CSA 59 1107-CSA 32 403-AP 17 450-TFC-2 21 499-CSA 59 1121-CSA 32 403-AP-M 17 455-CSA 41 500-K-BASE 64 1384-A 63 403-STF 16 457-25-CM 47 500-K-STL 64 1385-A 62 403-TF 16 457-CSA 47 500-K-STU-E 64 1388-A 63 403-TF-4 16 460-CSA 23 500-K-STZ 65 1392-A 63 405-M 19 460-FR 23 531044FULL-1003 56 1395-A 63 405-M-M 19 460-N 24 587011FULL-0110X 56 1396-A 63 405-TF-M-BE 19 460-NDIST 24 7092263FUL-0129 55 1440-CSA 37 410-FR 20 460-NS 24 7092270FUL-0147 55 1447-A 38 410-TF 20 460-S 23 81215-S 60 1447-CSA 38 410-TF-4 20 460-TF-2 23 81215-SBG 61 1450-24-Vac 53 410-TF-M 20 461-CSA 23 81215-SBP 61 1450-CSA 53 414-CTF 10 462-M 23 81230-S 60 1450-S-CSA 53 414-CTF-2 10 462-N 24 81230-SBG 61 1463-CSA 46 414-CTF-N 10 462-NS 24 81250-S 60 1463-FR 46 414-TF 9 462-SM 23 81250-SBG 61 1465-CSA 46 414-TF-2 9 470-CSA 42 A470 45 1467-FR 46 415-STF 11 471-A 43 AG-10 28 2152-CSA 39 415-TF 11 471-CSA 43 CSA05403 50 2450-N 54 415-TF-2 11 473-CN 44 CSA06632 57 2450-NM 54 415-TF-2-M 11 473-N 44 CSA07960 59 2460-B 56 415-TF-M 11 474-CSA 45 CSA07970 58 2495-CSA 65 415-TF-M-BE 11 476-CSA 48 CSA07980 65 2498-R 65 416-TF 12 482-CSA 49 300-K-BASE 64 423-TF 13 483-CSA 49 The group Cooper Industries Founded as a small foundry in 1833 at Mount Vernon in Ohio, USA, by the brothers Charles and Elias Cooper, Cooper Industries is now a worldwide manufacturer with leadership positions in the electrical market. In the first 125 years of its history, the company was concentrated in the production of gas compression and distribution devices, as well as diesel engines for boats. In 1960 Cooper started a products portfolio diversification process with a series of takeovers and a slight international expansion. Today the product lines include equipment for the oil industry, products for electric power distribution, emergency lighting, fire and intrusion systems. The presence of Cooper in Europe must be attributed to a series of takeovers of high level brands such as CEAG, Menvier, and MTL. With a vast network of companies, Cooper Industries holds today a strong leadership in innovation, development, production, distribution and technical support in the whole world. 4 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Cooper Safety Cooper CSA When there are lives and properties to protect, It is a company of the Cooper Industries there is no room for compromises, and you group, active on the Italian market since need a partner that can support you with more than 35 years with products and tested and certified products, with capacity and solutions for the fire and intrusion security international expertise and the local support as and the emergency lighting. Cooper CSA is well. Here is where Cooper Safety comes into based in Corsico, Milano where it operates the picture. with a team of highly specialized promoters As a division of the Cooper Industries group, we and commercial officers and a network of are a global leader in solutions and technologies branches diffusely spread over the national designed to save lives and protect the territory. properties. Our products and brands, leader on Every day in contact with designers, dealers the market, are present in the most demanding and engineers, our staff is able to provide industrial, residential and commercial support in all phases of the project, from environments, where we are able to offer the development of complex technological solutions for fire detection, intrusion, emergency systems to their commissioning, with a lighting and escape route indication, traditional precise and prompt service. and LED lighting, emergency notifications. We provide safety to persons and goods with passion and competence With a enviable reputation as for innovation, quality and performance, our range of products includes brands such as CEAG systems for emergency lighting, Menvier equipment for emergency lighting, CSA - Fulleon - Wheelock components and Accessories availableeses for fire and security systems, MEDC signalling devices for dangerous areas, Scantronic wired and wireless intrusion systems. The continuous international success is the result of passion and ability of our business units that offer an excellence and innovation heritage in their respective fields of competence. Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 5 Micro contacts Brass flush-mounting micro contact •Series314 • Compliant with and under certification in accordance with EN50131-2-6 • Ultra-compact dimensions • Flush-mounting • Brass body • Suitable for aluminium, wood and PVC doors and windows • With anti-tampering wire loop It is mounted with pressure on the frame into a 6 mm diameter hole. The reed section contains a tight reed with polyurethane resin and anti-tampering loop to reduce violation risks. The item 314-N includes the flat magnet 300-MA. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for anti-tampering). Brass magnetic contact with high mechanical resistance for flush mounting. Although it is the smallest magnetic contact available, its operating distance is suitable for most applications, using of rare earth magnets and miniature reeds. Suitable to be mounted on aluminium, wood and PVC doors and windows, and in general, on all non-ferromagnetic materials (iron frames will significantly reduce operating distance). General specifications Housing material Natural brass Operation Reed contact with NC output with near magnet Type of connection Wires (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Anti-tampering wires Packaging 10 pc. / package Order codes Code D max (no iron) Connection type Max voltage Max current Max power N° wires Cable length Approvals Safety grade Environmental class Package weight 314-CSA 10 mm NC* 100 Vdc 250 mA 3W 4 0,3 m IMQ Liv I** 2 3 0,08 Kg 314-N 10 mm NC* 100 Vdc 250 mA 3W 4 0,3 m - - - 0,08 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet ** IMQ approval for outdoor use. The indicated maximum voltage data refer to the reeds inside the contacts, however the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac) 300-MA 6 10 314-N 6 10 3 (see page 28) 3 Accessories 6 2.5 2.5 Magnet 300-MA Flat magnet Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Micro contacts Aluminium surface-mounting micro contact •Series355 • Compliant with and certification pending in accordance with EN50131-2-6 • Small size • Surface mounting • Aluminium body • Suitable for aluminium, wood and PVC doors and windows • Also suitable for roller shutters • Wire connection • With anti-tampering wire loop application is to mount the magnet section onto the roller shutter (that must not be made of ferromagnetic material), so as to protect it from lifting. The reed section contains a tight reed with polyurethane resin and an anti-tampering loop to reduce violation risks. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for anti-tampering). Brass magnetic contact with high mechanical resistance for surface mounting. Despite compact size, its operating distance is suitable for most applications, using of rare earth magnets and miniature reeds. Suitable to be mounted on aluminium, wood and PVC doors and windows, and in general, on all non-ferromagnetic material (iron frames will significantly reduce operating distance). It is mounted by means of screws on the frame; an alternative General specifications Housing material Aluminium Operation Reed contact with NC output with near magnet Type of connection Wires (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Anti-tampering wires Packaging 10 pc. / package Order codes Code 355-CSA D max (no iron) Connection type Max voltage Max current Max power N° wires 10 mm NC* 100 Vdc 250 mA 3W 4 Cable length Safety grade 0,3 m 2 Environmental class Package weight 3 0,09 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet The indicated maximum voltage data refer to the reeds inside the contacts, however the product must be used within the very low voltage limits (max. voltage 74 Vdc 49 Vac) Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 7 Concealed magnetic contacts Concealed magnetic contact •Series 401 • Compliant with and certification pending in accordance with EN50131-2-6 • Concealed mounting • Only 4,5 mm thick • Suitable for Vasistas fixtures • Available in white & brown colours • Anti-tamper wire loop The reed part contains the reed encapsulated watertight with the two-component polyurethane resin in conjunction with a loop tamper in order to reduce the risk of burglary. The connection is 4 core (2 core for the NC contact with near magnet and 2 core for the tamper). The 401 is fixed to the frame using screws. The 401 concealed magnetic contact can be installed on aluminium frames, wood, PVC, iron, etc. It is especially suitable for Vasistas fixtures, in fact the minimal thickness of the contact enables installation directly onto the chassis frame where a dept of just 4,5mm is the norm. Once closed the fixture contact is concealed in the space between the frame and window. General specifications Housing material Thermoplastic Operation Reed contact with NC output with near magnet Type of connection Wires (2 for contact + 2 for anti-tampering) Operating temperature -25°C / +70°C IP Degree IP 43 Standard equipment Anti-tampering wires Packaging 10 pc. / package (5 pz. modello da 3 m) Order codes Code D max (on iron) D max (no iron) Connection type Max voltage Max current Max power N° wires Cable length Colour Safety grade Environmental Package class weight 401-TF 20 mm 20 mm NC* 200 Vdc 1A 10 W 4 1,2 m White 2 3 0,5 Kg 401-TF-M 20 mm 20 mm NC* 200 Vdc 1A 10 W 4 1,2 m Brown 2 3 0,5 Kg 401-TF- 3 20 mm 20 mm NC* 200 Vdc 1A 10 W 4 3,0 m White 2 3 0,6 Kg 401-TF-M-3 20 mm 20 mm NC* 200 Vdc 1A 10 W 4 3,0 m Brown 2 3 0,6 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet The indicated maximum voltage data refer to the reeds inside the contacts, however the product must be used within the very low voltage limits (max. voltage 74 Vdc 49 Vac). 8 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Flush-mounting magnetic contacts Brass cylindrical short magnetic contact •Series 414 • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • Wide operating distance • Suitable for aluminium, wood and PVC doors and windows • Wire connection • With anti-tampering wire loop Brass magnetic contact with high mechanical resistance for flush mounting on doors and windows. The body of the contact is galvanized for a better aesthetic result and a higher corrosion resistance. Suitable to be mounted on aluminium, wood and PVC doors and windows, and in general, on all non-ferromagnetic material (iron frames will significantly reduce operating distance). The wide operating distance allows installation on frames having large tolerances or clearances. It is mounted with pressure on the frame into an 8 mmdiameter hole. The reed section contains a tight reed bulb with polyurethane resin and an anti-tampering loop to reduce the risk of burglary. Available with cable lenght of 30cm and 2m. Connection uses 4 wires. General specifications Housing material White galvanised brass Operation Reed contact with NC output with near magnet Type of connection or changeover reed contact Operating temperature Wires (2 for contact + 2 for anti-tampering) IP Degree IP 65 Standard equipment Anti-tampering wires Packaging 10 pc. / package Order codes Code D max (no iron) Max curConnection Max power N° wires Max voltage rent type Cable length Approvals Safety grade Environmental class Package weight 414-TF 14 mm NC* 200 Vdc 1A 10 W 4 0,3 m IMQ Liv I** 2 3 0,19 Kg 414-TF-2 14 mm NC* 200 Vdc 1A 10 W 4 2,0 m IMQ Liv I** 2 3 0,58 Kg Notess Sheathed cable The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet ** IMQ approval for outdoor use The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 9 Flush-mounting magnetic contacts Brass cylindrical short magnetic contact •Series 414 C • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • Compact dimensions for thin frames • High mechanical resistance • Suitable for aluminium, wood and PVC doors and windows • With anti-tampering wire loop It is mounted with pressure on the frame into an 8 mm diameter hole. The reed section contains a tight reed bulb with polyurethane resin and an anti-tampering loop to reduce the risk of burglary. The item 414 CTF-N is equipped with a flat magnet 300-MA. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for anti-tampering). Brass magnetic contact with high mechanical resistance for flush mounting on doors and windows. Thanks to powerful rare earth magnets, magnets section is very short to be mounted onto thin-section frames. Suitable to be mounted on aluminium, wood and PVC doors and windows, and in general, on all non-ferromagnetic material (iron frames will significantly reduce operating distance). General specifications Housing material Natural brass Operation Reed contact with NC output with near magnet Type of connection Wires (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Anti-tampering wires Packaging 10 pc. / package Order codes Code 414-CTF D max (no iron) Connection type Max voltage Max current Max power N° wires Cable length Approvals Safety grade Environmental class 12 mm NC* 100 Vdc 1A 10 W 4 0,3 m IMQ Liv I** 2 3 414-CTF-2 12 mm NC* 100 Vdc 1A 10 W 4 2,0 m - 2 3 414-CTF-N 11 mm NC* 100 Vdc 1A 10 W 4 0,3 m - 2 3 Package weight Notes 0,19 Kg 0,58 Kg Sheathed cable 0,19 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet ** IMQ approval for outdoor use. The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). 2.5 Accessories available 300-MA 10 10 414-CTF-N 6 3 Magnet 300-MA (see page 28) Flat magnet Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Flush-mounting magnetic contacts Thermoplastic cylindrical magnetic contact •Series 415 • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • Long operating distance • Suitable for aluminium, wood and PVC doors and windows • With anti-tampering wire loop • White and brown colours Thermoplastic magnetic contact for flush mounting on doors and windows. Suitable to be mounted on aluminium, wood and PVC doors and windows, and in general, on all non-ferromagnetic material (iron frames will significantly reduce operating distance). Its long operating distance allows installation also on window frames with large tolerance or play. It is mounted with pressure on the frame into an 8 mm diameter hole. The reed section contains a tight reed bulb with polyurethane resin and an anti-tampering loop to reduce violation risks. Available versions include NC contact, NC-NO (changeover) contact, and different cable lengths. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for antitampering) or 5 wires with changeover reed (3 wires for reed contacts + 2 wires for anti-tampering). Available in white and brown colours. General specifications Housing material Thermoplastic in colours as from table Operation Reed contact with NC output with near magnet or changeover reed contact Type of connection Wire (2 for contact - 3 for changeover contact + 2 for anti-tampering) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Anti-tampering wires Packaging 10 pc. / package Order codes Code D max Connection Max (no iron) type voltage Max current Max power N° wires Cable length Colour Approvals Safety grade Environmental class Package weight IMQ Liv I** Vds G191596 cl.B 2 3 0,11 Kg 2 3 0,50 Kg 2 3 0,11 Kg 2 3 0,50 Kg 415-TF 15 mm NC* 200 Vdc 1A 10 W 4 0,3 m White 415-TF-2 15 mm NC* 200 Vdc 1A 10 W 4 2,0 m White 415-TF-M 15 mm NC* 200 Vdc 1A 10 W 4 0,3 m Brown IMQ Liv I** IMQ Liv I** IMQ Liv I** 15 mm NC* 200 Vdc 1A 10 W 4 2,0 m Brown 415-TF-M-BE 15 mm NC* 200 Vdc 1A 10 W 4 0,3 m Brown INCERT N° B-630-0001 2 3 0,11 Kg 3W 5 0,3 m White - 2 3 0,11 Kg 415-TF-2-M 415-STF 9 mm changeover 100 Vdc 300 mA Notes Sheathed cable Sheathed cable Accessories available 300-MA 10 6 The indicated maximum voltage data refer to the reed bulbs inside the contacts. il prodotto deve comunque essere utilizzato entro i limiti di bassissima tensione (tensione max 74 Vdc - 49 Vac) 3 The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet 2.5 ** IMQ approval for outdoor use. Magnet 300-MA (see page 28) Flat magnet Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 11 Flush-mounting magnetic contacts Flush-mounting magnetic contacts •Series 416 • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting version of the reed • Surface-mounting version of the magnet • Long operating distance • Suitable for aluminium, wood and PVC doors and windows • Wire connection • With anti-tampering wire loop The reed section is mounted with pressure on the frame into an 8 mm diameter hole, while the magnet section is screwed. The reed section contains a tight reed with polyurethane resin and an anti-tampering loop to reduce violation risks. Available versions include NC contact, NC-NO (changeover) contact, and different cable lengths. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for anti-tampering). Thermoplastic magnetic contact with flush-mounting reed section on the window frame. It is similar to series 415, with the only difference that the magnet section is surface-mounting on the wing. Suitable to be mounted on aluminium, wood and PVC doors and windows, and in general, on all non-ferromagnetic material (iron frames will significantly reduce operating distance). Its long operating distance allows installation also on window frames with large tolerance or play. General specifications Housing material reed White colour thermoplastic Housing material magnete Nickel-plated brass Operation Reed contact with NC output with near magnet Type of connection Wires (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Anti-tampering wires Packaging 10 pc. / package Order codes Code 416-TF D max (no iron) Connection type Max voltage Max current Max power N° wires Cable length Safety grade Environmental class Package weight 15 mm NC* 200 Vdc 1A 10 W 4 0,3 m 2 3 0,13 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance. * With near magnet The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). 12 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Flush-mounting magnetic contacts Magnetic contact for armoured doors •Series 423 • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • Long operating distance • Suitable for doors and windows of any material • Wire connection • With anti-tampering wire loop Typical applications include: armoured doors, iron doors and gates. It is pressure mounted into a 22 mm diameter hole. The reed section contains a tight reed bulb with polyurethane resin and an anti-tampering loop to reduce violation risks. Thermoplastic magnetic contact for flush mounting on the window frame. It is suitable for any kind of door/window, even of ferromagnetic material (iron). Thanks to a phosphor bronze spring, the contact stays away from the frame material, thus minimizing the reduction of the magnetic field caused by ferrous materials, while preserving a good operating distance. General specifications Housing material White colour thermoplastic Spring material Phosphor bronze Operation Reed contact with NC output with near magnet Type of connection Wires (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Anti-tampering wires Packaging 2 pc. / package Order codes Code 423-TF D max (no iron) D max (on iron) Connection type Max voltage Max current Max power N° wires Cable length Approvals Safety grade Environmental class Package weight Notess 23 mm 12 mm NC* 200 Vdc 1A 10 W 4 1,2 m IMQ Liv I** 2 3 0,12 Kg Sheathed cable The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet ** IMQ approval for outdoor use. The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 13 Flush-mounting magnetic contacts Magnetic contact for armoured doors •Series 424 • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • Suitable for doors and windows of any material • Wire connection • With anti-tampering wire loop doors and gate. It is pressure mounted into 20 mm diameter hole. The reed section contains a tight reed bulb with polyurethane resin and an anti-tampering loop to reduce violation risk. Wired connection. Brass magnetic contact for flush mounting into window frame. It is suitable for any kind if door/window, even ferromagnetic material (iron). Thanks to a special knurling, the contact sticks perfectly where necessary. Typical applications include: armoured doors, iron General specifications Housing material Brass Operation Reed contact with NC output with near magnet Type of connection Wire (2 for contact, 2 for anti-tamper) for TF models Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Anti-tampering wires Packaging 2 pc. / package Order codes Code 424-TF D max (no iron) D max (on iron) Connection type Max voltage Max current Max power N° wires Cable length Approvals Safety grade Environmental class Package weight 20 mm 12 mm NC* 200 Vdc 1A 10 W 4 1,2 m IMQ Liv I** 3 3 0,18 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet ** IMQ approval for outdoor use. The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). 14 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Surface-mounting magnetic contacts Thermoplastic magnetic contact with terminals •Series 400 • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • Suitable for doors and windows of any material • Terminal connection • Protection against cover opening and removal from the wall Simple installation thanks to terminal connection (clamping screws) and application by means of screws or two-sided tape. Thermoplastic magnetic contact for surface mounting. It is suitable for door/window frames of any material: aluminium, wood, PVC, iron etc. It is protected against removal from the wall and cover opening. General specifications Housing material Thermoplastic in colour as from table Operation Reed contact with NC output with near magnet Type of connection Wires (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +70°C IP Degree IP 40 Standard equipment Two-sided tape, anti-tampering Packaging 10 pc. / package Order codes Code 400-FR D max (no iron) D max (on iron) Connection type Max voltage Max current Max power Colour Approvals Safety grade Environmental class Package weight 15 mm 11 mm NC* 200 Vdc 1A 10 W White NF A2P TYPE 3 2 2 0,31 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 15 Surface-mounting magnetic contacts Thermoplastic magnetic contact •Series 403 • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • Suitable for aluminium, wood and PVC doors and windows • Wire connection • Anti-tamper wire loop • Good quality/price level Thermoplastic magnetic contact for surface mounting with good quality/price ratio. Suitable to be mounted on aluminium, wood and PVC doors and windows, and in general, on all nonferromagnetic materials (iron frames will significantly reduce operating distance). The reed section contains a tight reed bulb with polyurethane resin and an anti-tampering loop to reduce violation risks. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for anti-tampering) or 5 wires with changeover reed (3 wires for reed bulb contacts + 2 wires for anti-tampering). It is mounted onto the frame by means of screws. General specifications Housing material White colour thermoplastic Operation Reed contact with NC output with near magnet or changeover reed contact Type of connection Wire (2 for contact - 3 for changeover contact + 2 for anti-tampering) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Anti-tampering wires Packaging 10 pc. / package Order codes D max (no iron) Connection type Max voltage Max current Max power N° wires Cable length Approvals Safety grade Environmental class 403-TF 15 mm NC* 200 Vdc 1A 10 W 4 0,3 m IMQ Liv I** 2 3 0,14 Kg 403-TF-4 15 mm NC* 200 Vdc 1A 10 W 4 4,0 m IMQ Liv I** 2 3 0,92 Kg 403-STF 9 mm scambio 100 Vdc 300 mA 3W 5 0,3 m - 2 3 0,15 Kg Code Package weight Notess Sheathed cable The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet ** IMQ approval for outdoor use. The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). 16 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Surface-mounting magnetic contacts Compact metal magnetic contact •Series 403 AP • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • High mechanical resistance • Suitable for doors and windows of any material • Wire connection • Anti-tamper wire loop resin and an anti-tampering loop to reduce violation risks. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for anti-tampering). It is mounted onto the frame by screws. Metal magnetic contact for surface mounting with high mechanical resistance. It is suitable to be mounted on door/window frames of any material: aluminium, wood, PVC, iron etc. The reed section contains a tight reed bulb with polyurethane General specifications Housing material Metal alloy Operation Reed contact with NC output with near magnet Type of connection Wires (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Anti-tampering wires Packaging 10 pc. / package Order codes Code D max (no iron) D max (on iron) Connection type Max voltage Max current Max power N° wires Cable length Colour Safety grade Environmental class Package weight 403-AP 18 mm 7 mm NC* 200 Vdc 1A 10 W 4 1,2 m Aluminium 2 3 0,28 Kg 403-AP-M 18 mm 7 mm NC* 200 Vdc 1A 10 W 4 1,2 m Brown 2 3 0,28 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 17 Surface-mounting magnetic contacts Metallic magnetic contact •Series403 AG • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • High mechanical resistance • Long operating distance • Suitable for doors and windows of any material • Wire connection • Anti-tamper wire loop The reed section contains a tight reed bulb with polyurethane resin and an anti-tampering loop to reduce violation risks. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for anti-tampering). It is mounted onto the frame by screws. Metal magnetic contact for surface mounting with high mechanical resistance. It is suitable to be mounted on door/window frames of any material: aluminium, wood, PVC, iron etc., even with large tolerance or play thanks to the long operating distance. General specifications Housing material Metal alloy, aluminium colour Operation Reed contact with NC output with near magnet Type of connection Wires (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Anti-tampering wires Packaging 5 pc. / package Order codes Code 403-AG D max (no iron) D max (on iron) Connection type Max voltage Max current Max power N° wires Cable length Safety grade Environmental class Package weight Notess 22 mm 10 mm NC* 200 Vdc 1A 10 W 4 1,2 m 2 3 0,55 Kg Sheathed cable The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). 18 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Surface-mounting magnetic contacts Thermoplastic magnetic contact • Series 405 • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • Suitable for doors and windows of any material • Terminal connection • White and brown colours The wire versions have an anti-tampering loop to reduce violation risks. Available in white and brown colour. Thermoplastic magnetic contact for surface mounting. It is suitable for door/window frames of any material: aluminium, wood, PVC, iron etc. Wire (mod. TF) or terminal connection (M models). General specifications Housing material Thermoplastic in colours as from table Operation Reed contact with NC output with near magnet Type of connection Wire (TF models) or terminal (M models) Operating temperature -25°C ÷ +70°C IP Degree IP 40 Packaging 10 pc. / package Order codes Max current Max power N° wires Cable length Colour Safety grade 200 Vdc 1A 10 W 4 0,3 m Brown 2 2 0,24 Kg NC* 200 Vdc 1A 10 W 2 mors. - White 2 2 0,19 Kg NC* 200 Vdc 1A 10 W 2 mors. - Brown 2 2 0,19 Kg Code D max (no iron) D max Connection Max (on iron) type voltage 405-TF-M-BE 15 mm 11 mm NC* 405-M 15 mm 11 mm 405-M-M 15 mm 11 mm Environmental Package class weight Notes Approval INCERT N° B-630-0001 The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 19 Surface-mounting magnetic contacts Flush or surface-mounting magnetic contact •Series 410 • Compliant with and certification pending according EN50131-2-6 • Exceptional versatility: flush or surface mounting • Suitable for aluminium, wood and PVC doors and windows • Wire connection • With anti-tampering wire loop Thermoplastic magnetic contact for flush or surface mounting. Maximum installation versatility (ideal for ready-to-use antitheft kits). It can be flush mounted by inserting the cylindrical bodies into 8 mm diameter holes, or surface-mounted using the supplied adapters with hidden screws. Suitable to be mounted on aluminium, wood and PVC doors and windows, and in general, on all non-ferromagnetic material (iron frames will significantly reduce operating distance). The reed section contains a tight reed bulb with polyurethane resin and an anti-tampering loop to reduce violation risks. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for anti-tampering). General specifications Housing material Thermoplastic in colours as from table Operation Reed contact with NC output with near magnet Type of connection Sheathed wire (2 for contact + 2 for tamper) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Shims, anti-tampering wires Packaging 10 pc. / package Order codes Code D max Connection (no iron) type Max voltage Max current Max power N° wires Cable length Colour Approvals Safety grade Environmental class Package weight White IMQ Liv. I** Vds G191588 Cl.B 2 3 0,59 Kg 410-TF 15 mm NC* 200 Vdc 1A 10 W 4 2,0 m 410-TF-4 15 mm NC* 200 Vdc 1A 10 W 4 4,0 m White IMQ Liv. I** 2 3 1,00 Kg 410-TF-M 15 mm NC* 200 Vdc 1A 10 W 4 2,0 m Brown IMQ Liv. I** 2 3 0,59 Kg 410-FR 15 mm NC* 200 Vdc 1A 10 W 4 2,0 m White NF A2P TYPE 3 2 3 0,59 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet ** Omologato IMQ per utilizzo interno. The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). 20 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Surface-mounting magnetic contacts Magnetic contact for garage doors •Series 450 • Compliant with and certification pending in accordance with EN50131-2-6 • Floor mounting • Die-cast aluminium housing • Wire connection • With anti-tampering wire loop • Steel sheath The reed section contains a tight reed bulb with polyurethane resin and an anti-tampering loop to reduce violation risks. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for anti-tampering), protected by a steel sheath, and covered by black PVC. Contact 450-TFC-2 is magnetically balanced to reduce the risk of violation through an external magnet. Aluminium magnetic contact for garage or sliding/folding doors. The strong housing construction of die-cast aluminium ensures maximum resistance under the wheels of heavy-load vehicles, fork-lift trucks etc., making it suitable for heavy-duty applications. The reed part is fixed to the ground with three screws, while the magnet is mounted on the door (6 mounting holes available). Its long operating distances allow efficient operation also with doors of large gap. General specifications Housing material Die-cast aluminium Operation Reed contact with NC output with near magnet Type of connection Wires (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +55°C IP Degree IP 65 Standard equipment Cable protection sheathing, 10 mm diameter, 1 m length, steel with black PVC coating; antitampering wires Packaging 1 pc. / package Order codes Code 450-CSA Y max/X max (no iron) Y max (on iron) Max voltage Max current Max power N° wires Cable length Approvals Safety grade Environmental class Package weight 35/25 mm 20 mm 200 Vdc 1A 10 W 4 1,2 m IMQ Liv. I* Vds G191589 Cl.B 2 3 0,24 Kg 0,19 Kg 450-FR 35/25 mm 20 mm 200 Vdc 1A 10 W 4 1,2 m NF A2P TYPE 3 3 4 450-TF-2 35/25 mm 20 mm 200 Vdc 1A 10 W 4 2,0 m IMQ Liv. I* 2 3 13-18/16 mm 16 mm 100 Vdc 300 mA 3W 4 2,0 m Vds G198067 Cl.C 3 4 450-TFC-2 0,19 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. Y max: maximum vertical installation distance; X max: maximum horizontal installation distance (see diagram below). * IMQ approval for outdoor use The indicated maximum voltage data refer to the reed bulbs inside the contacts. , However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac) Accessories available AG-10 Diagram of Y and X distances (see page 28) Black PVC-coated steel sheath - 10 m Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 21 Surface-mounting magnetic contacts Magnetic contact for garage doors •Series 450 N • Compliant with and certification pending in accordance with EN50131-2-6 • Floor mounting • Die-cast aluminium housing • Long operation distance • With anti-tampering wire loop • Steel sheath fork-lift trucks etc., making it suitable for heavy-duty applications. Its long operating distances allow efficient operation also with doors with large play. The reed section contains a tight reed bulb with polyurethane resin and an anti-tampering loop to reduce violation risks. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for anti-tampering), protected by a steel sheath, and covered by black PVC. Aluminium magnetic contact for garage or sliding/folding doors. It is a new version of contact series 450 with the following enhancements: new look, longer operating distances, reed part mounting with only two screws that can be protected by special metal caps, possibility of cable entrance from the ground, magnet part with smaller vertical hole distance for simpler mounting on the door. The sturdy housing construction of die-cast aluminium ensures maximum resistance under the wheels of heavy-load vehicles, General specifications Housing material Die-cast aluminium Operation Reed contact with NC output with near magnet Type of connection Wire (2 for contact + 2 for tamper) Operating temperature -25°C ÷ +55°C IP Degree IP 34 Standard equipment Cable protection sheathing, 10 mm diameter, 1 m length, steel with black PVC coating; anti-tampering wires, caps Packaging 1 pc. / package Order codes Code 450-N Y max/X max (no iron) Y max (on iron) Connection type Max voltage Max current Max power N° wires Cable length Approvals Safety grade Environmental class Package weight 27/23 mm 20/7 mm NC* 200 Vdc 1A 10 W 4 1,2 m IMQ Liv. I** 2 4 0,34 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. Y max: maximum vertical installation distance; X max: maximum horizontal installation distance (see diagram below). * With near magnet ** IMQ approval for outdoor use The indicated maximum voltage data refer to the reed bulbs inside the contacts. , However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac) Accessories available AG-10 22 Diagram of Y and X distances (see page 28) Black PVC-coated steel sheath - 10 m Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Surface-mounting magnetic contacts Aluminium power magnetic contact •Series 460 • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • Die-cast aluminium housing • Long operation distance • Suitable for doors and windows of any material tight reed bulb with polyurethane resin and an anti-tampering loop to reduce violation risks. The terminal connected version is provided with tear-off protection and a printed circuit board that can house balancing resistors. Arranged to be protected with a 10 mm diameter black PVC coated steel cable sheath (not included). Aluminium magnetic contact for surface mounting. Thanks to its solid die-cast aluminium structure, it is suitable for applications in factories, shopping malls, etc. Its long operating distance allows the use on frames of any material and with large play. Available with wire and terminal connection (462 model). The wire connected version has a reed section that contains a General specifications Housing material Die-cast aluminium Operation Reed contact with NC output with near magnet or changeover reed contact Type of connection Wire or terminals (2 for contact - 3 for changeover contact + 2 for anti-tampering) Operating temperature -25°C ÷ +55°C IP Degree IP 65 (only for version with wire connection) Standard equipment Tamper-proof caps, cable gland, anti-tampering wires, plastic spacer (not for models 462) Packaging 2 pc. / package Order codes D max (no iron) D max (on iron) Connection type Max voltage Max current Max power N° wires Cable length Approvals Safety grade Environmental class Package weight 460-CSA 21 mm 14 mm NC* 200 Vdc 1A 10 W 4 1,2 m IMQ Liv. I** Vds G191590 Cl.B 2 4 0,30 Kg 460-FR 21 mm 14 mm NC* 200 Vdc 1A 10 W 4 1,2 m NF A2P TYPE 3 2 4 0,30 Kg 460-S 15 mm 10 mm scambio 100 Vdc 300 mA 3W 5 1,2 m - 2 4 0,30 Kg 0,35 Kg Code 460-TF-2 21 mm 14 mm NC* 200 Vdc 1A 10 W 4 2,0 m IMQ Liv. I** 2 4 462-M 20 mm 15 mm NC* 200 Vdc 1A 10 W 4 mors. - IMQ Liv. I** 2 2 0,25 Kg 462-SM 14 mm 10 mm scambio 100 Vdc 300 mA 3W 5 mors. - - 2 2 0,25 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet ** IMQ approval for outdoor use The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits max 74 Vdc - 49 Vac) Accessories available 462-M (see page 28) 461-CSA Plastic spacer for 460 – 462 AG-10 Black PVC-coated steel sheath - 10 m Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 23 Surface-mounting magnetic contacts Aluminium magnetic contact •Series 460 N • Compliant with and certification pending in accordance with EN50131-2-6 • Flush mounting • Die-cast aluminium housing • Long operation distance • Suitable for doors and windows of any material • Simplified installation Available with wire and terminal connection. The version with wire connection has a reed section that contains a tight reed with polyurethane resin and an antitampering loop to reduce violation risks. The version with terminal connection is provided with tear-off protection and a printed circuit board able to house eventual balancing resistors. Arranged to be protected with a Ø 10 mm black PVC coated steel cable sheath (not included). Aluminium magnetic contact for surface mounting. It is the new version of contact series 460, with the following enhancements: renewed aesthetics, fixing symmetry, extremely simplified installation for the version with terminal connection thanks to the circuit’s snap mounting. Thanks to its solid die-cast aluminium structure, it is suitable for applications in factories, shopping malls, etc. Its long operating distance allows the use on frames of any material and with large play. for sheath 10mm General specifications Housing material Die-cast aluminium Operation Reed contact with NC output with near magnet or changeover reed contact Type of connection Wire or terminals (2 for contact - 3 for changeover contact + 2 for anti-tampering) Operating temperature -25°C ÷ +55°C IP Degree IP 34 (only for version with wire connection) Standard equipment Tamper-proof caps, cable gland, anti-tampering wires Packaging 2 pc. / package Order codes Code D max (no iron) D max (on iron) Connection type Max voltage Max current Max power N° wires Cable length Approvals Safety grade Environmental class Package weight 460-N 20 mm 12 mm NC* 200 Vdc 1A 10 W 4 1,2 m IMQ Liv. I** 2 4 0,30 Kg 460-NS 15 mm 10 mm changeover 100 Vdc 300 mA 3W 5 1,2 m - 2 4 0,30 Kg 462-N 30 mm 25 mm NC* 200 Vdc 1A 10 W 4 term. - IMQ Liv. I** 2 2 0,25 Kg 462-NS 14 mm 10 mm changeover 100 Vdc 300 mA 3W 5 term. - - 2 2 0,25 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet ** IMQ approval for outdoor use 462-N The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac) Accessories available (see page 28) 460-NDIST Plastic spacer for 460 – 462 AG-10 Black PVC-coated steel sheath - 10 m 24 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Surface-mounting magnetic contacts Long-distance magnetic contact •Series 1005 • Compliant with and certification pending in accordance with EN50131-2-6 • Surface mounting • Very long operation distance • Indoor use • Suitable for frames of any material • Wire connection • With anti-tampering wire loop Aluminium magnetic contact for surface mounting. It derives from the High-Security series 1000, featuring the same look, but it was developed to have a very long operating distance for all those applications where the frames have large play and tolerances, and therefore a normal magnetic contact could cause false alarms. It can be applied to frames of any material, also iron. The connection is with anti-tampering wire loop and cable sheathing of plasticized steel. General specifications Housing material Anodized aluminium Operation Reed contact with NC output with near magnet Type of connection Wire or terminal (2 for contact + 2 for anti-tampering) Operating temperature -15°C ÷ +55°C IP Degree IP 40 Standard equipment Tamper-proof caps, cable protection sheathing with 10 mmdiameter, 1.7 m length, steel with black PVC coating; anti-tampering wires Packaging 1 pc. / package Order codes Code 1005-CSA D max (no iron) D max (on iron) Connection type Max voltage Max current Max power N° wires Cable length Safety grade Environmental class Package weight 55 mm 30 mm NC* 200 Vdc 1A 10 W 4 2,0 m 2 2 0,56 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Accessories available AG-10 (see page 28) Black PVC-coated steel sheath - 10 m Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 25 Surface-mounting magnetic contacts Long-distance magnetic contact IP 65 •Series 1005 N • Compliant with and certification pending in accordance with EN50131-2-6 • Indoor or outdoor use • Small dimensions • Suitable for frames of any material • Protection against violation • Very long operation distance avoiding the addition of junction boxes and its cap with umbrella structure detects any type of mechanical violation. Available version 1035-N with remote test facility. Supplied with plastic cable gland M16 and tamper for cap removing detection. Aluminium magnetic contact for surface mounting. It derives from series 1000-N High Security, and is suitable for any surface installation. It keeps its ingress protection IP 65 and maintains nice beauty with high operating distance. The terminal block connection makes installation easier General specifications Housing material Metal annealed epoxy white painting Operation Reed contact with NC output with near magnet Type of connection By terminals (1,5 sq mm) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Mounting template, IP 65 cable glands Packaging 1 pc. / package Order codes D max (no iron) D max (on iron) Connection type Max voltage Max current Max power Safety grade Environmental class Package weight 1005-N 63 mm 40 mm NC* 100 Vdc 500 mA 10 W 2 4 0,65 Kg 1035-N 63 mm 40 mm NC* 100 Vdc 500 mA 10 W 2 4 0,65 Kg Code Notess Tear-off protection for reed and magnet with connection for remote testing The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Accessories available AG-10 26 (see page 28) Black PVC-coated steel sheath - 10 m Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Surface-mounting magnetic contacts Long-distance magnetic contact •Series 1105 • Compliant with and certification pending in accordance with EN50131-2-6 • Surface mounting • Very long operation distance • High electric power • Suitable for frames of any material • Terminal connection • Protection against cover opening Reed bulbs are high-power devices and also the version with changeover reed bulb is available. Protected against cover opening through an internal micro switch. Simplified installation thanks to the 3/8 gas cable entrance hole (cable gland included) and the terminal connection. Aluminium magnetic contact for surface mounting. It derives from the High-Security series 1100, featuring the same look, but it was developed to have a very long operating distance for all those applications where the frames have large play and tolerances, and therefore a normal magnetic contact could cause false alarms. It can be applied to frames of any material, also iron. Thanks to the high IP degree, it can be installed in any indoor and outdoor environment. General specifications Housing material Die-cast aluminium, white epoxy painting Operation Reed contact with NC output with near magnet Type of connection Terminal (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +55°C IP Degree IP 65 Standard equipment Tamper-proof caps, IP 65 cable gland Packaging 1 pc. / package Order codes Code 1105-CSA D max (no iron) D max (on iron) Connection type Max voltage Max current Max power N° terminals Safety grade Environmental class Package weight 55 mm 35 mm NC* 400 Vdc 3A 100 W 4 2 3 0,87 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance * With near magnet The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Accessories available AG-10 (see page 28) Black PVC-coated steel sheath - 10 m Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 27 Accessories for surface mounting magnetic contacts 461 • Spacerfor460series • Itismountedunderthereedofseries460soastobealigned with the corresponding magnetic part • Madeofgreythermoplasticmaterial AG-10 • BlackPVC-coatedsteelsheath • Itmechanicallyprotectscablesagainstbothaccidentalimpact and cutting • Externaldiameter10mm,length10m • Suitableforcableswithadiameterupto5mm • Itcanbecut-to-sizewithahacksaw Order codes Code Description Pc./package. Package weight Applicability 461-CSA Plastic spacer for 460-462 10 0,06 Kg Series 460 460-NDIST Plastic spacer for 460 N 10 0,06 Kg Series 460 N AG-10 Black PVC-coated steel sheath - 10 m 1 1,0 Kg 28 Series 450 - 450 N - 460 - 460 N - 1000 - 1005 - 1105 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Contatti magnetici ad alta sicurezza Indoor high-security magnetic contact •Series 1000 • Compliant with and certification pending in accordance with EN50131-2-6 • Indoor surface mounting • Annealed aluminium housing • Suitable for frames of any material • Wire connection • Protection against violation Magnetic contact for indoor surface mounting with high security standard. Series 1000, in an elegant annealed aluminium case, is a standard equipment for security systems in banks, shopping malls and all those facilities that require most security in external protection. It is equipped with protection against magnetic, electric and mechanical violation. The double or triple balancing magnetic circuits, where all different reeds interlace to the magnetic fields generated by magnet batteries, are unbalanced by the application of an external magnet, triggering the alarm as a consequence. Wire protection is ensured by an anti-tampering loop and a plasticized steel sheath. Versions 1021 and 1031 offer maximum security with tear-off protection through micro switch and antitampering loop for the reed section and the magnet part (4 wires on the magnet part); moreover, the version 1031 is linked to the central control unit for remote testing (6 wires on the reed part). M versions (without cable) are provided with a window and related cover to directly access the circuit board on which the operator can mount one or more resistors, in series or parallel to the contact. Equipped with iron anti-tamper caps. General specifications Housing material Annealed aluminium Operation Reed contact with NC output with near magnet Type of connection Wire (except 1003 M) Operating temperature -15°C ÷ +55°C IP Degree IP 40 Standard equipment Tamper-proof caps, cable protection sheathing - 10 mm diameter, 1.7 m length - made of steel with black PVC coating; anti-tampering wires, mounting templates Packaging 1 pc. / package Order codes Code D max D max Max vol- Max cur(no iron) (on iron) tage rent Max power N° wires Cable length Approvals Safety grade Envir. class Package weight Notes 1001-CSA 14 mm 9 mm 100 Vdc 300 mA 3W 4 2,0 m IMQ Liv. I* 3 2 0,55 Kg Triple balancing 1003-CSA 21 mm 15 mm 100 Vdc 300 mA 3W 4 2,0 m IMQ Liv. I* 2 2 0,52 Kg Double balancing, 1003-M 21 mm 15 mm 100 Vdc 300 mA 3W - - - 2 2 0,50 Kg Double balancing, with opening, no cable 1021-CSA 14 mm 9 mm 100 Vdc 300 mA 3W 4+4 2,0 m IMQ Liv. II* 3 2 0,79 Kg Triple balancing with tear-off protection for reed and magnet part The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance; as the contacts are balanced, the minimum installation distance must be complied with as specified in the instruction sheet * IMQ approval for indoor use. The indicated maximum voltage data refer to the reed bulbs inside the contacts. , However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac) Accessories available AG-10 1003-M 1021-CSA (see page 28) Black PVC-coated steel sheath - 10 m Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 29 Contatti magnetici ad alta sicurezza High-security magnetic contact IP 65 •Series 1000 N • Compliant with and certification pending according EN50131-2-6 • Indoor or outdoor use • Small dimensions • Suitable for frames of any material • Terminal connections • Protection against violation Magnetic contact for indoor and outdoor surface mounting with high security standards. The nice and sober design of the metallic case links installation practicality and robustness. Series 1000 N is suitable for security system in a bank (many models are IMQ I or II level certified), in a shopping centre and public office; the internal magnetic circuits are designed for having double and triple balancing, for assuring a protection against any type of violation (mechanical, electrical and magnetic). All models don’t need any junction box considering the internal terminal connections. Each model has tamper protection against cap opening. The fixing nut housing into container is arranged to accept cable or tube gland 16mm and cable till 10mm of diameter (as standard accessory there is a M16 cable gland). Version 1021 N offers maximum security with tear-off protection through micro switch for reed and magnet part and triple balancing, ensuring the maximum security. General specifications Housing material Metal annealed, epoxy white painting Operation Reed contact with NC output with near magnet. Type of connection By terminals (1,5 sq mm) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Standard equipment Mounting template, IP 65 cable glands Packaging 1 pc. / package Order codes Code D max D max (no iron) (on iron) Max voltage Max current Max power Approvals Safety grade Environmental class Package weight Notes 1001-N 15 mm 13 mm 100 Vdc 300 mA 3W IMQ Liv. I* 3 4 0,65 Kg Triple balancing 1021-N 15 mm 13 mm 100 Vdc 300 mA 3W IMQ Liv. II* 3 4 0,65 Kg Triple balancing with tear-off protection for reed and magnet 1031-N 15 mm 13 mm 100 Vdc 300 mA 3W IMQ Liv. II* 3 4 0,65 Kg Like 1021 N but with link for remote test 1003-N 27 mm 20 mm 100 Vdc 300 mA 3W IMQ Liv. I* 3 4 0,65 Kg Double balancing The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance; as the contacts are balanced, the minimum installation distance must be complied with as specified in the instruction sheet. * IMQ approval for indoor use. The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Accessories available AG-10 30 (see page 28) Black PVC-coated steel sheath - 10 m Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it High-security magnetic contacts Flush-mounting high-security magnetic contact •Series 1050 • Compliant with and certification pending according EN50131-2-6 • Indoor flush mounting • Suitable for frames of any material • Wire connection • Protection against violation Magnetic contact for indoor flush mounting with high security level. The double or triple balancing magnetic circuit boards, where all different reeds interlace to the magnetic fields generated by magnet batteries, are unbalanced by the application of an external magnet, triggering the alarm as a consequence. Wire protection is ensured by an anti-tampering loop. It is screwed to the frame after having created a recess opening of adequate dimensions. General specifications Housing material Annealed aluminium Materiale placca Nickel-plated brass Operation Reed contact with NC output with near magnet. Type of connection Wire Operating temperature -25°C ÷ +55°C IP Degree IP 40 Packaging 1 pc. / package Mounting holes Order codes Code D max (no iron) D max (on iron) Max voltage N° Max curMax power wires rent Cable length Approvals Safety grade Environmental class Package weight Notess 1051-CSA 12 mm 8 mm 100 Vdc 300 mA 1,2 m IMQ Liv. II* 3 2 0,42 Kg Triple balancing 3W 4 The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance; as the contacts are balanced, the minimum installation distance must be complied with as specified in the instruction sheet. * IMQ approval for indoor use. The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 31 High-security magnetic contacts High-security magnetic contact IP 65 •Series 1100 • Compliant with and certification pending according EN50131-2-6 • Outdoor flush mounting • Suitable for frames of any material • Terminal connection • Protection against violation for the reed part, and opening and tear-off protection for the magnet part, and it is provided with a link for remote testing. Versions 1103-CSA have high-power contacts reed bulbs, while version 1107-CSA offers further protection thanks to an incorporated thermal sensor set at 60° C to detect violation through oxyhydrogen flame) and an inertial sensor (it must be interfaced with the analysis card 448-CSA). Simplified installation thanks to the 3/8 gas cable entrance hole (cable-gland included) and the terminal connection. Magnetic contact for indoor or outdoor surface mounting with high security level. Made of solid cast-die aluminium with epoxy white painting, it is equipped with protection against magnetic, electric and mechanical violation. The double-balancing or interlaced-flow magnetic circuits, where all different reed bulbs interlace to the magnetic fields generated by magnet batteries, are unbalanced by the application of an external magnet, triggering the alarm as a consequence. All contacts are protected against cap opening on the reed part. The high-security version 1121-CSA also features tear-off protection General specifications Housing material Metal annealed, epoxy white painting Operation Reed contact with NC output with near magnet. Type of connection Terminal Operating temperature -25°C ÷ +55°C IP Degree IP 65 Standard equipment IP 65 cable gland, mounting templates Packaging 1 pc. / package Order codes Code D max D max (no iron) (on iron) Max voltage Max current Max power Approvals Safety grade Environmental class Package weight Notes 1101-CSA 14 mm 9 mm 200 Vdc 1A 10 W IMQ Liv. I* 3 3 0,85 Kg Interlaced flow 1103-CSA 28 mm 19 mm 500 Vdc 500 mA 30 W IMQ Liv. I* 2 3 0,80 Kg Double balancing 1107-CSA 14 mm 9 mm 200 Vdc 1A 10 W - 3 3 0,88 Kg Interlaced flow with inertial and thermal sensor 1121-CSA 14 mm 9 mm 200 Vdc 1A 10 W IMQ Liv. III* 3 3 0,90 Kg Interlaced flow with protection against opening and tear-off on reed and magnet, remote testing The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance; as the contacts are balanced, the minimum installation distance must be complied with as specified in the instruction sheet. * IMQ approval for indoor use The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac) Accessories available AG-10 32 1121-CSA (see page 28) Black PVC-coated steel sheath - 10 m Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Inertia and vibration sensors Mercury vibration sensor •443 • Surface mounting • Thermoplastic body • Inclination detection • Wire connection It is normally used on glass knockout cabinets, garage doors, top hinged windows, etc. to report a status or position change. 4-wire connection, 2 for contact and 2 for the antitampering loop. It is fixed with two-sided tape (included). NC or NO contact that switches according to the inclination of the object on which it is fixed. It is possible to calibrate the contact sensitivity by adequately rotating the body holding the mercury reed bulb. According to the fixed position, it has a closed or open contact. General specifications Housing material Thermoplastic, white colour Operation Mercury contact with NC or NO output (according to position) Type of connection Wire Operating temperature -25°C ÷ +55°C IP Degree IP 43 Standard equipment Two-sided tape for application Packaging 10 pc. / package Order codes Code 443-CSA Connection type Max voltage Max current Max power N° wires Cable length Contact resistance Package weight NC o NA* 200 Vdc 500 mA 20 W 4 1,2 m 0,05 Ohm 0,38 Kg D max: maximum installation distance. * With near magnet The indicated maximum voltage data refer to the mercury bulb included in the device. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 33 Inertia and vibration sensors Sensore inerziale •444 • Surface mounting • Impact detection • Gold-plated contacts • Wire connection • Anti-tampering wire loop Inertia sensor for impact detection. It incorporates goldplated contacts which, in case of impact onto the mounting surface, open the contact (NC in normal conditions) for a time proportional to the impact strength It is normally used on doors, windows and wherever it is necessary to detect impact. It must be interfaced by shielded cable to an analysis board, such as 448, which features adjustable sensitivity and can be connected to several sensors in series. 4-wire connection, 2 for contact and 2 for the anti-tampering loop with shielded cable. It is fixed with screws or two-sided tape. General specifications Housing material Thermoplastic, white colour Operation Multiple gold-plated contacts with NC output Type of connection Wire (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +55°C IP Degree IP 54 Standard equipment Anti-tampering wires Packaging 5 pc. / package Order codes Code 444-CSA Connection type Max voltage Max current Max power N° wires Cable length Package weight NC 100 Vdc 100 mA 3W 4 2,0 m 0,40 Kg However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Accessories available 448-CSA 34 (see page 40) Analysis card for inertia sensors Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Inertia and vibration sensors Inertia sensor in self-protected housing •Series 446 • Indoor surface mounting • Impact detection • Gold-plated contacts • Protection against cover opening • Incorporated analysis card • Microprocessor technology Inertia sensor for impact detection in self-protected housing. It incorporates gold-plated contacts which, in case of any perpendicular impact onto the mounting surface, open the contact (NC in normal conditions) for a time proportional to the impact strength. It is normally used on doors, windows and wherever it is necessary to detect impact. The series 446 is provided in two versions: the 446-AN is provided with incorporated analysis card with sensitivity adjustment for the inertia sensor through a trimmer, selectable NC-NO relay output and LED memory. Version 446-AVR is on the contrary suitable for connection with radio transmitters and presents a very low draw open-collector output. Both versions are supplied with terminal connection and micro switch protection against cover opening included. General specifications Housing material Termoplastico Colour bianco Materiale sensore Contatti multipli dorati Type of connection Terminals Operating temperature -25°C ÷ +70°C IP Degree IP 30 Packaging 1 pc. / package Order codes Connection type Rated voltage 446-AN NC/NA 446-AVR Open Collector Code Rated current Max relay current Pc./package. Package weight 10-15 Vdc 4-24 mA 1A 1 0,11 Kg 2,5-5 Vdc 16-400 µA - 1 0,11 Kg Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 35 Inertia and vibration sensors Piezoelectric sensor •Series 447 • Version with magnetic contact available • White or brown colour • Double Knock feature • Connection by terminals • Tamper protection • Sensitivity control • LED memory • IP 65 model available All models offer a latching Led indication that can be remotely reset of left illuminated to act as deterrent. Sensitivity is controlled by a variable potentiometer coupled with a Dual Sensitivity link – so offering fine adjustment possibilities. Available with or without magnetic contact, in white or brown colour, is also available in an outdoor installation model IP 65 in white colour. Piezoelectric sensor for the detection of vibrations and impacts. The sensors 447 have been designed using advanced CMOS technology, to offer a product that will out perform immunity to false alarm. The very robust design with no moving parts is non-gravity dependent therefore allowing installation in any position over a flat surface. General specifications Housing material Thermoplastic white or brown colour. IP 65 version Metal annealed, epoxy white painting Operation Shock sensor with relay output NC. In the contact version there is reed switch connected in series with shock sensor to signal also door opening. To be installed on strong-box and window. Type of connection By terminals (2 for switch output – 2 for tamper – 2 for power supply – 1 for remote control – 1 for First to Alarm bus) Operating temperature -10°C ÷ +50°C IP Degree IP 40 (IP 65 version 447-IP65) Standard equipment Fixing screws. IP 65 version cable-gland Packaging 1 pc. / package Order codes Magnetic contact Protection grade White no IP 40 0,07 Kg White Yes IP 40 0,08 Kg Brown No IP 40 0,07 Kg Brown Yes IP 40 0,08 Kg White No IP 65 0,35 Kg Connection type Max voltage Max current N° terminals Colour 447-B NC 9,5 - 15 Vdc 8 mA 8 447-C NC 9,5 - 15 Vdc 8 mA 8 447-M NC 9,5 - 15 Vdc 8 mA 8 447-CM NC 9,5 - 15 Vdc 8 mA 8 447-IP65 NC 9,5 - 15 Vdc 8 mA 8 Code 447-IP65 36 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Package weight Inertia and vibration sensors Hammer inertia sensor •1440 • Indoor surface mounting • Impact detection through a hammer • Adjustable sensitivity • Protection against tear-off from the surface and opening Inertia sensor for the detection of any surface impact through a small hammer with screw-adjustable sensitivity. The sensor can be applied onto any surface subject to impact, such as glass sheets, movable partition walls, doors, windows etc. High reliability ensured by silver-plated contacts. Protection against tear-off from the mounting surface and cover opening. Simplified installation thanks to clamping screw connections and two-sided tape application (included). General specifications Housing material Thermoplastic, white colour Operation Selectable NC or NO output contact Type of connection Clamping screws Operating temperature -25°C ÷ +70°C IP Degree IP 20 Packaging 10 pc. / package Order codes Code 1440-CSA Connection type Max voltage Max current Max power Package weight NC o NA 100 Vdc 100 mA 3W 0,03 Kg The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 37 Inertia and vibration sensors IP 65 aluminium inertia sensor •Series Series 1447 • Outdoor surface mounting • Impact detection • Gold-plated contacts • Terminal connection • Protection against cover opening • Version with incorporated analysis card Inertia sensor for impact detection designed for outdoor installation. It incorporates multiple gold-plated contacts which, in case of impact onto the mounting surface, open the contact (NC in normal conditions) for a time proportional to the impact strength. It is normally used on doors, windows and wherever it is necessary to detect impact, also outdoors or in indoor environments laden with moisture or dust. Version 1447-CSA must be interfaced by shielded cable to an analysis board, such as 448-CSA, which features adjustable sensitivity and can be connected to several sensors in series. Version 1447-A is provided with incorporated analysis card with double sensitivity adjustment for the inertial sensor through a trimmer, selectable NC-NO relay output. Terminal connection and 3/8 gas cable entry. Micro switch protection against cover opening. Available, bracket for installation on wire mesh. General specifications Housing material Annealed aluminium, white epoxy painting Operation NC output contact (1447) Type of connection Terminals Operating temperature -25°C ÷ +55°C IP Degree IP 65 Standard equipment Hole cap Packaging 1 pc. / package Order codes Code Connection type Voltage Current Max power Package weight Notes 1447-CSA NC 100 Vdc max 1447-A NC 10-15 Vdc 100 mA max 3W 0,44 Kg Needs analysis card 448-CSA 2-30 mA Relè 1A max 0,46 Kg The product must be used within the very low voltage limits (max. 74 Vdc - 49 Vac). Accessories available 448-CSA 38 1447-A (see page 40) Analysis card for inertia sensors Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Inertia and vibration sensors Piezoelectric detector with memory •2152 • Outdoor surface mounting • Detection of typical glass crashing frequencies • With LED memory Piezoelectric sensor able of detecting the typical frequency of glass breaking, while remaining insensitive to impact or other vibration. It is provided with dual connection (2+2 wires) to shunt the connections for other sensors. The contact is normally open (NO) and closes when the glass breaking/cutting frequency is detected. It must be interfaced to an analysis board, such as 448-CSA, which features relay output and controls the sensor with balanced line. Each analysis card can be connected to several sensors in parallel. LED alarm memory. It is applied to the glass with a specific adhesive (twocomponent iron-glass glue is recommended, such as Loctite 317 with 736NF activator). Operating reach: 2 m approx. It is not suitable for bullet-proof glass. General specifications Housing material Thermoplastic, white colour Operation NO output Type of connection Wire (2+2 cores) Operating temperature -10°C ÷ +70°C IP Degree IP 67 Packaging 1 pc. / package Order codes Code Connection type Supply voltage Current draw N° wires Wire Lenght Approvals Package weight NA 3÷16 Vdc 8 mA* 2+2 2,0 m Vds n. G196614B 0,08 Kg 2152-CSA * In alarm; 1µA at rest. Accessories available 448-CSA (see page 40) Analysis card for inertia sensors Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 39 Accessories for inertia and vibration sensors 448 • Analysiscardforinertiaorvibrationsensors • Processingofsensorsignalswithadjustablealarmthreshold and selectable NO-NC relay output • 10-15Vdcpowersupply • 2mAconsumption,30mAwithexcitedrelay • Doubleadjustmentrangeforoperatingsensitivity • 2200Ohmbalancedlineinput • Dimensions:80x40mm • Equippedwithadhesivesupportsforquickinstallation Order codes Code 448-CSA 40 Description Pc./package Package weight Applicability Analysis card for inertia sensors 2 0,12 Kg Series 444, 446, 1447, 2152, 1107 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Contacts for roller shutters Magnetic contact for roller shutters •455 • Compact dimensions • Suitable for frames of any material • Wire connection • With anti-tampering wire loop resin and an anti-tampering loop to reduce violation risks. Connection uses 4 wires (2 wires for NC contact with near magnet and 2 wires for anti-tampering). It is mounted by screws. Low-thickness magnetic contact. Suitable for installation on frames of any material: aluminium, wood, PVC, iron, etc. The low thickness of the magnet part makes it particularly suitable for application onto roller shutters or gates. The reed section contains a tight reed bulb with polyurethane General specifications Housing material reed Nickel-plated brass Housing material magnete Nickel-plated iron and brass Operation Reed contact with NC output with near magnet Type of connection Wire (2 for contact + 2 for anti-tampering) Operating temperature -25°C ÷ +70°C IP Degree IP 65 Packaging 2 pc. / package Order codes Code 455-CSA D max (no iron) D max (on iron) Connection type Max voltage Max current Max power N° wires Cable length Approvals Safety grade Environmental class Package weight 30 mm 20 mm NC* 200 Vdc 1A 10 W 4 1,2 m IMQ Liv. I** 2 4 0,20 Kg The “Safety grade” and “Environmental Class” are two new classifications introduced by the EN50131 regulation, for further information see on page 66. D max: maximum installation distance. * With near magnet. ** IMQ approval for outdoor use. The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 41 Contacts for roller shutters Rod contact for roller shutters •470 • Installation in the roller shutter box • With reed contact • Insensitive to moisture and dust • Wire connection Rod contact to detect the lifting of roller shutters or gates. It is mounted inside the box, pushing the rod against the roller shaft. When the roller shutter is lifted, the roll thickness increases, so that the rod rotates around a cam that actuates a reed button, triggering the alarm. Thanks to the reed button, the system is highly reliable also in humid and dusty environments. Cost-effective installation is ensured by the fact that no contact analysis card is required. Connection uses 2 wires (NC contact with lowered roller shutter). General specifications Housing material Thermoplastic, black colour Materiale asta Aluminium Operation Reed contact with NC output with lowered roller shutter Type of connection Wire (2 per contact) Operating temperature -25°C ÷ +55°C IP Degree Indoor use Packaging 5 pc. / package Order codes Code 470-CSA Connection type Max voltage Max current Max power N° wires Cable length Rod lenght Package weight NC* 200 Vdc 1A 10 W 2 0,2 m 0,4 m 1,2 Kg * With lowered roller shutter. The indicated maximum voltage data refer to the reed bulbs inside the contacts. However the product must be used within the very low voltage limits (max. voltage 74 Vdc - 49 Vac). Accessories available A470 42 (see page 45) Burnished steel rod for 470 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Contacts for roller shutters Rope contact for roller shutters •471 • Installation in the roller shutter box • Detection of all movements of the roller shutter • Wire connection • Requires analysis card 471-A Rope contact to protect roller shutters and gates against tearoff, cutting and lifting. It is mounted inside the box, and it is completely invisible. The rope is hooked to the roller shutter and transmits motion to an internal cam that drives an NC micro-switch. It is necessary to interface the contact to an analysis card, code 471-A, with a relay output, with which it is possible to program the number of pulses for the alarm generation, avoiding false alarms caused, for instance, by the shutters’ slow sliding. It is possible to connect several sensors to the same analysis card. The contact must be installed next to the shutter edge of the box. In order to enhance installation, an extension slide, code 474, is available. The contact is fixed to the roller shutter box through screws or tape (not included). General specifications Housing material Thermoplastic, white colour Operation Micro-switch contact with NC output Type of connection Wire Operating temperature -25°C ÷ +70°C IP Degree IP 40 Packaging 2 pc. / package Order codes Code Connection type Max voltage Max current Max power N° wires Cable length Rope lenght Package weight 471-CSA NC* 75 Vdc 3A 100 W 2 0,2 m 3,1 m 0,26 Kg * With roller shutter stopped. Accessories available (see page 45) 471-A Analysis card for rope contacts 474-CSA Extension slide for rope contacts Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 43 Contacts for roller shutters Rope magnetic contact for roller shutters •Series 473 • Installation in the roller shutter box • Detection of movements of the roller shutter • Integrated analysis card • Utmost reliability thanks to reed contacts • Wire connection • Radio line version Rope magnetic contact to protect roller shutters and gates against tear-off, cutting and lifting. It is mounted inside the box, and it is completely invisible. The rope is hooked to the roller shutter and transmits motion to an internal magnetic cam that drives the reeds. The signal from the reed bulbs is processed by an integrated analysis card. Two different versions are available according to the required application. Version 473-N has a changeover relay output, while version 473-CN has an open-collector output for interfacing with radio transmitters. The contact must be installed next to the shutter edge of the box. In order to enhance installation, an extension slide, code 474CSA, is available. The contact is fixed to the roller shutter box through screws or tape (not included). General specifications Housing material Thermoplastic, white colour Type of connection Wire (6 coloured wires for 473-N, 4 coloured wires for 473-CN) Operating temperature -25°C ÷ +70°C IP Degree IP32 Packaging 1 pc. / package Order codes Code Output Nominal voltage Stand-by current Alarm current Output activation time Cable length Package weight 473-N Relè NC/NA 10.5 - 13,8 Vdc 3mA min 30mA max 14mA min 20mA max 2,0s 0,3m 0,85 Kg 473-CN CMOS (open collector) 2,5 - 5,5 Vdc 1 µA @3,6V 100 µA @3,6V 2,5s 1,5m 0,90 Kg Accessories available 474-CSA 44 (see page 45) Extension slide for rope contacts Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Accessories for roller shutters contacts A470 • Spare rod for 470 contact • Material: Burnished steel • Length: 40 cm 471-A • Analysis card to detect pulses of the 471-CSA rope contact • Generates an alarm above 0.5 s with a number of pulses equal to or higher than the set value (from 1 to 15) or if the rope sensor connection is interrupted • LED for pulse/alarm signalling • Relay changeover output max. 1 A, 75 Vdc • 12 Vdc ±20% power supply; 3.3 mA consumption with relay at rest, 20 mA with excited relay • It is suggested not to connect more than 5 sensors to simplify research in case of alarm • Dimensions: 55x37x20 mm • Adhesive supports included 474-CSA • Extension slide for rope contacts • Simplifies installation as it enables to fix rope contact towards the back of the box • In galvanized steel 5 holes 4mm diameter Order codes Code Description Pc./package. Package weight Applicability A470 Burnished steel rod for 470 1 0,07 Kg 470-CSA 471-A Analysis card for rope contacts 1 0,03 Kg 471-CSA 474-CSA Extension slide for rope contacts 1 0,12 Kg Series 471, 473 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 45 Junction boxes and auxiliary circuits 1463-CSA/1463-FR • Self-protected6-polesjunctionboxtoconnectsensorsto the line • Housingmaterial:aluminium • Micro-switchprotectionagainstopening • Terminalconnectionwith2.5sqmmmax.section:6poles + 2 poles for protection against opening • Entryforhose/sheathdiam.16mmor3/8gascablegland PG9 - exit for hose/sheath diam. 10 mm • IPDegreeIP54 • Operatingtemperature:-25°Cto+70°C • Code1463-FRapprovedNFA2PTYPE3,IP43 • Standardequipment:2cableglandsPG9for1463-CSA; 1cable-gland PG9 + 1 3/8 gas nut for 1463-FR 1465-CSA • Self-protected20-polesjunctionboxtoconnectseverallines and/or sensors • Housingmaterial:aluminium,epoxywhitepainting • Micro-switchprotectionagainstopening • Terminalconnectionmaxsection2.5sqmm:6single,4 double, 2 triple poles, 2 anti-tampering poles • 43/8gasthreadedentries • IPDegreeIP54 • Operatingtemperature:-25°Cto+70°C • Standardequipment: 2 3/8 gas threaded caps, cable legend, drilling template 1467-FR • Self-protected3-polesjunctionboxtoconnectsensorsto the line • Housingmaterial:thermoplastic,whitecolour • Protectionagainstopeningandtear-off • Clampingscrewconnections:3singlepoles(withthe possibility of soldering terminals) + 2 poles for protection • IPDegreeIP43 • Operatingtemperature:-25°Cto+70°C • ApprovalNF2APTYPE3 Order codes Code Description Pc./package Package weight 1463-CSA Self-protected 6-poles junction box 1 0,17 Kg 1463-FR Self-protected 6-poles junction box NF approved 1 0,17 Kg 1465-CSA Self-protected 20-poles shunting box 1 0,45 Kg 1467-FR Self-protected 3-poles junction box NF approved 1 0,02 Kg 46 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Security devices anti burglary Anti-robberyreedbutton•Series457 • Flush mounting • Silent reed contact • For several functions several applications or devices. Flush mounting with a 13 mm diameter hole. Version with welding terminals and a 25 cm long cable. Anti-robbery reed button. By pushing the button, a magnet gets silently close to the reed bulb, closing the contact. It can be used also as a mechanically-driven reed contact in General specifications Housing material: Thermoplastic, black colour Type of connection: Welding terminals (457-CSA), wire (457-25-CM) Operating temperature -25°C÷+70°C IP Degree IP40 Packaging 25 pc. / package Order codes Tipo di contatto Max voltage Max current Max. power Connection 457-CSA NO 75 Vdc 1A 10W Welding terminals 0,25 Kg 457-25-CM NO 75 Vdc 1A 10W 25 cm wire 0,35 Kg Code Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Package weight 47 Security devices anti burglary Anti-panic button •476 • Micro-switch protection against opening • Protection cover, possibility of sealing Anti-panic button to signal alarms. Button pushing causes the breaking of paper membrane showing alarm activation, and moves the changeover microswitch. Protected against opening by an internal changeover microswitch. Equipped with transparent protection cover that can be sealed with lead. The high security of this button is certified by the IMQ Level III and Vds class C. General specifications Housing material Thermoplastic, colours according to table Cover material Thermoplastic transparent Type of connection Clamping screws (3 for protection contact against opening, 3 for button contact) Operating temperature +5°C÷+40°C IP Degree IP 32 Standard equipment N° 4 paper membranes Packaging 1 pc. / package Order codes Code 476-CSA 48 Contacts Contacts max voltage Contacts max current Colour Opening protection Approvals Package weight 1 changeover 75 Vdc 3A White Yes IMQ Liv. III Vds n. G192028 0,18 Kg Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Security devices anti burglary Foot pressure mat •482 / 483 • Impact detection • Minimum operating pressure 1.5 Kg • Only 3.5 mm thick Foot pressure mat that, thanks to its very low thickness, can be placed under carpets, runners, deep-pile carpets, etc. It is made of several layers of hardened and tinned steel strips divided by a thin insulating layer. When the mat detects a localized pressure higher than 1.5 Kg, it closes the output contact. Wire connections. Version 482-CSA is provided in 5 m long rolls that can be cut according to the required length. General specifications Mat material PVC, colours according to table Contact elements material Hardened and tinned steel Operation NO contact Type of connection Wire Operating temperature -15°C÷+55°C IP Degree (indoor use) Packaging 1 pc. / package Order codes Contatti Max voltage Max current Lenght A 482-CSA NO 75 Vdc 500 mA 5000 mm 483-CSA NO 75 Vdc 500 mA 745 mm Code Width Connection Colour Package weight 740 mm 3,0 mm Welding terminals Transparent 3,43 Kg 425 mm 3,5 mm 2 wires 0,7 m Black 0,56 Kg Lenght B Notes Reinforced PVC 482-CSA Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 49 Security devices anti burglary Anti-panic button •Series484 • Silent operation • Protection against opening • Version with LED memory Reed button designed for the silent signalling of robberies in action. By pushing the button, a magnet gets close to the internal reed and opens the contact, thus triggering the alarm. Self-protection against opening through internal reed. Internal reeds are designed for NC operation. Simplified installation thanks to the two-sided tape included. The button is approved IMQ Lev. III and PPTT. Version 484-I is equipped with self-retaining button. To reset, a specific key included in the package is necessary. 4-terminal connection: 2 for contact and 2 for anti-tampering. Version 484-ME: LED memory with central reset (by cutting power supply), button with spring return. 6-terminal connection: 2 for contact, 2 for anti-tampering, 2 for 12 Vdc power supply. General specifications Cover material Anodized steel Housing material Thermoplastic, white colour Operation NC reed contact Type of connection Terminals Operating temperature +5°C÷+40°C IP Degree IP 32 Standard equipment Two-sided fixing tape. Reset key for 484-I Packaging 1 pc. / package Key recovery model only 484-I Model only Leds 484-ME Order codes Connection type Max voltage Max current Max power 484-I NC 75 Vdc 1A 10 W 484-ME NC 75 Vdc 1A 10 W Code LED memory Connections Approvals Package weight - No 4 terminals PPTT - IMQ Liv. III 0,07 Kg Key reset 12 Vdc - 10 mA Yes 6 terminals PPTT - IMQ Liv. III 0,07 Kg Central reset Power supply 484-ME Accessories available CSA05403 50 Spare key for 484-I Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Notes Security devices anti burglary Foot-operating button •Series 485 • Operated by lifting the foot tip • Silent operation • Protection against opening • Version with LED memory 4-terminal connection: 2 for contact and 2 for anti-tampering. Version 485-ME: LED memory with central reset (by cutting power supply). 6-terminal connection: 2 for contact, 2 for anti-tampering, 2 for 12 Vdc power supply. Foot-operating button silently actuated by slightly raising the foot. The internal reed contact is designed for NC operation. The mechanically high-resistance steel case is self-protected against opening. Version 485-I is equipped with self-retaining pedal. To reset, a specific key included in the package is necessary (keys are different for each product). General specifications Housing material Sheet steel, epoxy grey painting Front material Sheet steel, epoxy white painting Operation NC reed contact Type of connection Terminals Operating temperature -15°C÷+55°C IP Degree IP 40 Standard equipment Set with 2 reset keys (excluding 485-ME) Packaging 1 pc. / package Order codes Connection type Max voltage Max current Max power 485-I NC 75 Vdc 1A 10 W 485-ME NC 75 Vdc 1A 10 W Code Power supply LED memory Connections Package weight - No 4 terminals 1,92 Kg Key reset 12 Vdc - 10 mA Yes 6 terminals 1,75 Kg Central reset Notes 485-ME Accessories available CSA06632 Spare key for 485-I Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 51 Heat and flooding detectors Multipurpose detector •FIRECAT • Optical, optical-heat, rate of rise heat or fixed temperature heat sensor • Relay output • Dual LED indicator • Base can be locked against detachment Conventional multi-purpose detector that can be operated as either an optical, optical-heat, rate of rise heat or fixed temperature heat sensor at 77° with dip-switch adjustment. Suitable for direct connection with most conventional third party central stations. The detector is equipped with a 12V relay base and can be configured to store the alarm condition in memory or to restore automatically. The detector is equipped with a dual LED indicator: fixed red LED indicating the alarm/fault condition, blinking red LED indicating normal conditions, blinking yellow LED indicating smoke detection, some fault in the analysis chamber or the achievement of the maximum compensation capacity at the contamination site. General specifications Housing material Thermoplastic, white colour Type of connection NC (open when alarmed) Operating temperature -10°C ÷ +45°C IP Degree IP 40 Packaging 1 pc. / package Order codes Code Connection type Nominal voltage Nominal current Relay power Package weight 400001FULL-0001 NC (open when alarmed) 10-16 Vdc 0.5mA in standby 14mA in alarm 1A, 30V max 0,08 Kg 52 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Heat and flooding detectors Flooding and moisture detector •Series 1450 • Compact dimensions • Detection of water and moisture • Terminal connection • 1450 with relay output Sensor detecting water through 4 gold-plated supporting feet. It is normally used for the protection against the flooding of computing centres, boiler rooms, offices, laboratories, etc. It cannot be used with inflammable liquids. Version 1450-CSA, available with 12 or 24 Vdc power supply, is equipped with changeover relay output to control telephone combiners, alarm sirens, etc. In addition, it can be connected to several external probes 1450S-CSA (up to 10). For higher protection, it is also equipped with a moisture detector, whose sensitivity can be regulated with internal trimmer. Version with 24 Vac power supply is available. General specifications Housing material Thermoplastic, colours according to table Operation Detection of resistance between feet and internal coil Type of connection Terminals (2 for external feelers, 2 for power supply, 3 for relay output) Operating temperature +5°C ÷ +50°C IP Degree IP 40 Packaging 2 pc. / package Order codes Code 1450-CSA 1450-24-Vac 1450-S-CSA Power supply voltage Max. Current draw Relay power Colour Package weight Notes 12/24 Vdc 30 mA Changeover relay max 1 A, 30 Vdc White 0,16 Kg Can be connected to external probes code 1450-S-CSA 24 Vac 30 mA Changeover relay max 1 A, 30 Vdc White 0,16 Kg Can be connected to external probes code 1450-S-CSA 0,14 Kg External probe for 1450 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 53 Heat and flooding detectors IP 65 liquid detector •Series 2450 N • High mechanical resistance • Low consumption • Corrosion-proof system • Wire or terminal connections • Alarm signal LED • Relay output Sensor detecting water on the floor through 2 gold plated supporting feet. It is normally used for protection against the flooding of computing centres, boiler rooms, offices, laboratories, etc. The sensor contained into aluminium case epoxy white painting is equipped with a steel support that allows to detect liquid at height ranging form 0 to 11 mm according to specific needs. In alarm condition, relay changes its status and led lights. Remote testing and inhibition functions. The circuit is oscillating to prevent electrolysis and corrosion problem. 7 wire connection for 2450-N and terminal for 2450-NM: 2 power terminals, 3 terminal for changeover relay output, 1 for remote test, 1 terminal for inhibition. Version 2450-N offers a protection degree IP 67 thanks to full epoxy resin encapsulation. Trimmer adjustable alarm threshold for the resistor in version 2450-NM. It can not be used with inflammable liquids. General specifications Housing material Die-cast aluminium, epoxy white painting Operation Detection of resistance between feet. Changeover relay output Type of connection Wire or terminal Operating temperature -15°C ÷ +70°C Standard equipment Mounting bracket. 3/8”, Press hose M16 IP Degree See table Packaging 1 pc. / package Order codes Code 2450-N 2450-NM 54 N° wires Cable lenght IP Degree Package weight Changeover relay max 1 A, 30 Vdc 7 4,0 m IP 67 0,79 Kg Changeover relay max 1 A, 30 Vdc 7 terminals - IP 65 0,50 Kg Supply voltage Consumption in standby Consumption in alarm Outputs 12/24 Vdc 10 mA @ 12 Vdc 13 mA @ 24 Vdc 25 mA @ 12 Vdc 32 mA @ 24 Vdc 12/24 Vdc 10 mA @ 12 Vdc 13 mA @ 24 Vdc 25 mA @ 12 Vdc 32 mA @ 24 Vdc Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Notess Adjustable sensitivity Sounders and beacons Sounderwithbeacon•ASSERTAMINI • Tamper protection against opening • High sound power • Xeno flashlight • 32 selectable tones * • Dual tone alarm • High IP Degree IP 66 Electronic sounder with xeno flashlight and a high sound power. Suited for installation in outdoor environment thanks to the high IP Degree IP66. Possibility to include a tamper card against the opening (available as accessory). Wide range of power supply from 9 to 60 Vdc. Volume control. General specifications Housing material Thermoplastic, white colour Materiale calotta Thermoplastic, amber colour Type of connection Terminals Operating temperature -25°C ÷ +70°C IP Degree IP 66 Packaging 1 pc. / package Order codes Code Nominal voltage Nominal current Sound power Blinking frequency Package weight 7092270FUL-0147 9-60 Vdc 118-224 mA 113db** 1 Hz 0.43 Kg * For a list of selectable tones please refer to the Fire Alarm System Components catalogue. ** with tone n.6. Accessories available 7092263FUL-0129 Tamper card for Asserta mini sounder Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 55 Sounders and beacons 2460-B • Acousticsounderforindooruse • Compactdimensionsandlowconsumption • Housingmaterial:thermoplastic,whitecolour • 3to24Vdcpowersupply–consumption15mA@12Vdc,27 mA @ 24 Vdc • Intermittentsound3200Hz0.25sON,0.25sOFF;98dB@12 Vdc – 105 dB @ 24 Vdc at 1 m • Wireconnection • Operatingtemperature:-20°Cto+60°C 3465-12-BIANCA • Dual-tonepiezoelectricsirenforindooruse • Highsoundpower • Housingmaterial:thermoplastic,whitecolour • Domematerial:thermoplastic,transparent • Dual-tonesound2800-3100Hz0.5s/0.5s;110dB@1m • Xenoflashlight:60flash/min • Microswitchprotectionagainstopening • Terminalconnections-Operatingtemperature:-20°C÷+60°C • 12Vdcpowersupply–290mAconsumption 587011FULL-0110X • Electronicceiling-mountsounderSQUASHNIMicro-IP42for indoor use • 4selectabletones(forinformationseetheFireAlarmSystem Components catalogue) with a second pre-alarm tone • Housingmaterial:ABS,whitecolour. • 9-30Vdcpowersupply–consumption15mA@24Vdc • 97dBat1m • Terminalconnections–Operatingtemperature:-25°C÷+70°C 531044FULL-1003 • Xenobeaconwithanti-tampering-IP54:indoorandoutdoor use • Housingmaterial:ABS,whitecolour. Cover material: amber polycarbonate • Micro-switchprotectionagainstopening • Xenoflashlight:10cd,60flashes/min. • 9-60Vdcpowersupply,consumption88mA@24Vdc •Terminalconnection(6term.)-Operatingtemp.-20°C÷+70°C Order codes Code Description Pcs./package. Package weight 2460-B Acoustic sounder 1 0,14 Kg 3465-12-BIANCA Piezoelectric siren with flashlight 1 0,32 Kg 587011FULL-0110X Piezoelectric ceiling mount siren SQUASHNI Micro 1 0,16 Kg 531044FULL-1003 Xeno flashlight with tamper 1 0,30 Kg 56 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Security key locks 491-T • Mechanicalprotectionforelectrickeylocks • Itcanbeeasilyinstalledtoprotectelectricinserters,like Bticino “Magic” • Anti-tamperingcoverdesignedtoallowfreeaccessto buttons or other elements coupled to the electric key lock • Material:steel,epoxywhitepainting • Keylock • NCreedcontact • Pairofkeysincluded • CodeCSA-06632:keylockfor491-T 496-CSA • Inserterforsurface-mountingwithoutkeyblock • ForYALEorsimilarlocksets • Housingmaterial:die-castaluminium,epoxywhitepainting. Front material: annealed aluminium • Centralpositionand90°rotationtotherightandleft • Twochangeovercontactswithstablepositions,possible conversion to unstable positions • ThreesignallingLEDsandbuzzer–12Vdcpowersupply,10 mA for each element • Terminalconnections • Protections:keyblockremoval,frontdrilling,coverremoval, tear-off 496-I • Inserterforflush-mountingwithoutkeyblock • ForYALEorsimilarlocksets • Housingmaterial:galvanizedsteel.Frontmaterial:annealed aluminium • Centralpositionand90°rotationtotherightandleft • Twochangeovercontactswithstablepositions,possible conversion to unstable positions • ThreesignallingLEDsandbuzzer–12Vdcpowersupply,10 mA for each element • Terminalconnections • Protections:keyblockremoval,frontdrilling,coverremoval Order codes Code Description Pcs./package. Package weight 491-T Mechanical protection for electric key lock 1 0,40 Kg 496-CSA Inserter for surface-mounting without key block 1 0,63 Kg 496-I Inserter for flush-mounting without key block 1 0,37 Kg Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 57 Security key locks 497-5K • Keylockforflush-mountingwithroundkey • Housingmaterial:die-castaluminiumwithwhiteepoxy varnishing. Front material: annealed aluminium • TwoON/OFFcontactsthatcanbeturnedintochangeover contacts • ThreesignallingLEDs–12Vdcpowersupply,10mAforeach element • Terminalconnections • Protections:coverremoval,tear-off,violentblows • With5differentkeysdependingoneachproduct • IP50 • CodeCSA07970:sparekeysetfor497-5K 497-I-5K • Keylockforflush-mountingwithroundkey • Housingmaterial:thermoplastic.Frontmaterial:annealed aluminium • TwoON/OFFcontactsthatcanbeturnedintochangeover contacts • ThreesignallingLEDs–12Vdcpowersupply,10mAforeach element • Terminalconnections • Protections:coverremoval,violentblows • With5differentkeysdependingoneachproduct • CodeCSA07970:sparekeysetfor497-I-5K 73 497-SBC-19 / 497-SBC-23 • Inserterforsurface-mountingwithoutkeyblock • Housingmaterial:die-castaluminium,epoxywhitepainting. Front material: annealed aluminium • TwoON/OFFcontactsthatcanbeturnedintochangeover contacts • ThreesignallingLEDs–12Vdcpowersupply,10mAforeach element • Terminalconnections • Protections:coverremoval,tear-off,violentblows • Code497-SBC-19:forroundkeyblockwith19mmdiameter (like ABLOY, MEDECO, MINIKABA, etc.) • Code497-SBC-23:forroundkeyblockwith23mmdiameter (like KABA8/20) Order codes Code Description Pcs./package. Package weight 497-5K Key lock for surface-mounting 1 0,70 Kg 497-I-5K Key lock for flush-mounting 1 0,30 Kg 497-SBC-19 Inserter for surface-mounting without key block 1 0,61 Kg 497-SBC-23 Inserter for flush-mounting without key block 1 0,61 Kg 58 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Security key locks 497-I-SBC-19 / 497-I-SBC-23 • Inserterforflush-mountingwithoutkeyblock • Housingmaterial:thermoplastic.Frontmaterial:annealedaluminium • TwoON/OFFcontactsthatcanbeturnedintochangeover contacts • ThreesignallingLEDs–12Vdcpowersupply,10mAforeach element • Terminalconnections • Protections:coverremoval,violentblows • Code497-I-SBC-19:forroundkeyblockwith19mmdiameter (like ABLOY, MEDECO, MINIKABA, etc.) • Version497-I-SBC-23:forroundkeyblockwith23mm diameter (like KABA8/20) 498-CSA / 498-1512 • Keylockforsurface-mounting • Housingmaterial:die-castaluminium,epoxywhitepainting • Doublechangeovercontact • TwosignallingLEDs–12Vdcpowersupply,10mAforeach element • Wireterminalconnections • Protections:frontcoverremoval • Code498-CSA:with5keys(differentforeachproduct) • Code498/1512:with3keys,alwaysidenticalforallproducts • IP65 • Code07970:sparekeysetfor498 • Code07960:sparekeysetfor498/1512 499-CSA • Stainlesssteelinserterforsurface-mountingwithoutkeyblock • ForYALEorsimilarlocksets • Housingmaterial:die-castaluminium,epoxywhitepainting. Front material: stainless steel • Centralpositionand90°rotationtotherightandleft • Twochangeovercontactswithstablepositions,possibleconversion to unstable positions • ThreesignallingLEDsandbuzzer • 12Vdcpowersupply,10mAforeachelement • Terminalconnections • Protections:keyblockremoval,frontdrilling,coverremoval, tear-off Order codes Code Description Pcs./package. Package weight 497-I-SBC-19 Inserter for flush-mounting without key block 1 0,25 Kg 497-I-SBC-23 Inserter for flush-mounting without key block 1 0,25 Kg 0,51 Kg 498-CSA Key lock for surface-mounting 1 498-1512 Key lock for surface-mounting with identical keys 1 0,51 Kg 499-CSA Key lock for surface-mounting with identical keys 1 0,68 Kg Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 59 Power supply units Switching power supply unit 13,8 Vdc •Series 81000 S • Switching technology • Output voltage 13,8 Vdc • Compact size • High efficiency • Surface version • Lead battery charging UNI EN 60950 High quality switching power supply unit with 13.8 Vdc and currents at 1.5 A, 3 A and 5 A. Thanks to switching technology, it has small dimension, high efficiency and reduces at the least heating dissipation. High protection degree: overload, polarity inversion and short circuit. The mains power status is indicating by green LED. Indicated especially in small to medium size systems that need additional power supply. It can be installed into false ceilings or boxes suitable to house concentrators or junction boards. The most common use is supplying electromagnetic door holders (in access control systems) or connecting electric key locks, with high consumption, to release emergency exit doors, gates, etc. A B C 81215-S 98 135 40 81230-S 98 135 40 81250-S 98 165 42 General specifications Housing material Galvanised plate Type of connection Terminals Power supply 230 Vac -15+10%, 50÷60 Hz Lines Voltage input, battery output, load output Electric protection Earth fuse, overload, over voltage output, short circuit Operating temperature +5°C÷+40°C Insulation class Class I Packaging 1 pc. / package Order codes Code Nominal voltage Nominal current Output voltage Number and type of compatible batteries Package weight Notes 81215-S 20 W 1,5 A 13,8 Vdc 1 x 12V 7A 0,4 Kg Model A 81230-S 42 W 3A 13,8 Vdc 1 x 12V 17A 0,5 Kg Model B 81250-S 70 W 5A 13,8 Vdc 1 x 12V 42A 0,6 Kg Model C 60 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Power supply units Metallic box switching power supply unit 13,8 Vdc •Series 81000 SB • Switching technology • Output voltage 13,8 Vdc • High efficiency • Small or big metallic box • Lead battery charging UNI EN 60950 High quality power supply unit with 13.8 Vdc in a switching version with current at 1.5 A, 3 A and 5 A. Thanks to switching technology, it has high efficiency and reduces at the least heating dissipation. High protection degree: overload, polarity inversion and short circuit. 4 LEDs indicate power supply status: mains power (green), battery recharging (green), battery discharged (red), fault (red). All LEDs are visible and intelligible thanks to printed door. Indicated especially in small to medium size systems that need an additional power supply. For large systems, their use avoids long power supply cable runs, simplifying installation. Double box dimensions makes this product suitable for civil (small box) and industrial installations (large box). Wide space is available in the large box to insert expansion boards, concentrators junctions or any type of auxiliary cards. General specifications Housing material Epoxy painting plate Type of connection Terminals Power supply 230 Vac -15+10%, 50÷60 Hz Lines Voltage input, battery output, load output, open collector output for remote signals, general alarm output by relay contacts, opening door alarm Electric protection Earth and battery fuses, overload, short circuit, polarity battery inversion, opening box tamper Operating temperature +5°C÷+40°C Insulation class Class I IP Degree IP 30 Standard equipment 2 keys for lock Packaging 1 pc. / package A B C BOX A 290 250 180 BOX B 450 260 205 Order codes Code Nominal power Output current Output voltage Number and type of compatible batteries Package weight Notes 81215-SBP 20 W 1,5 A 13,8 Vdc 1 x 12V 7A 4,0 Kg Type A container (batteries not supplied) 81215-SBG 20 W 1,5 A 13,8 Vdc 1 x 12V 7A 6,2 Kg Type B container (batteries not supplied) 81230-SBG 42 W 3A 13,8 Vdc 1 x 12V 17A 6,4 Kg Type B container (batteries not supplied) 81250-SBG 70 W 5A 13,8 Vdc 1 x 12V 42A 6,6 Kg Type B container (batteries not supplied) Power supply unit with door open. N.B. Battery not supplied Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 61 Electromagnetic door holders Flush mounting electromagnetic door holder •1385 • Holding force 300 Kg • Counter plate included • 12-24 Vdc selectable • IP 40 version Flush mounting electromagnetic door holder to block emergency, anti-panic, access and passage doors. The high holding force allows to keep doors closed under normal condition. In case of emergency, the electromagnet unit is released, allowing door opening. Fail safe operation: the door is released in case of power drop, enabling the safe passage of people. General specifications 12 or 24 Vdc power supply, selectable through internal jumper. Thanks to wide range of auxiliary brackets, they can be mounted in several applications including glazed doors. These door holder units can be released by emergency buttons or specific control panels. 1385-A Body material Annealed aluminium Magnetic part material Galvanized steel Operation Release without power supply Type of connection Wire Operating temperature -10°C÷+55°C Standard equipment Galvanized steel counter plate, screws and mounting accessories Packaging 1 pc. / package A B C D 26 187 227 38 Order codes Code 1385-A 62 Holding force ±15 % Nominal voltage Nominal current Door status Mounting IP Degree Package weight Notess 300 Kg / 2490 N 12-24 Vdc 500 mA @ 12 Vdc 250 mA @ 24 Vdc Yes Flush mounting IP 40 1,82 Kg Damping counter plate Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Electromagnetic door holders Surface mounting electromagnetic door holders •Series 1390 • Flush mounting • Holding force 150 - 300 - 500 Kg • Damping counter plate included • 12-24 Vcc selectable • IP 40 and IP 65 protection Outdoor version available. 12 or 24 Vcc power supply, selectable through internal jumper. Thanks to the wide range of auxiliary brackets, they can be mounted in several applications including glazed doors. These door holder units can be released by emergency buttons or specific control panels. Series of surface mounting electromagnetic door holders to block emergency, anti-panic, access and passage doors. The high holding force allows to keep doors closed under normal condition. In case of emergency, the electromagnetic unit is released, allowing door opening. Fail safe operation: the door is released in case of power drop, enabling the safe passage of people. A B C 210 39 22 1388-A 250 48 25 1392-A 265 76 40 1395-A 532 76 40 1384-A General specifications Body material Annealed aluminium Magnetic part material Galvanized steel Operation Release without power supply Type of connection Terminals Operating temperature -10°C÷+55°C Standard equipment Galvanized steel counter plate, screws and mounting accessories Packaging 1 pc. / package Order codes Forza di tenuta ±15 % Tensione nominale Corrente nominale Stato porta Montaggio Grado di protezione Package weight 1384-A 150 Kg / 1470 N 12-24 Vdc 300 mA @ 12 Vdc 150 mA @ 24 Vdc si a vista IP 40 1,80 Kg Con LED 1388-A 300 Kg / 2490 N 12-24 Vdc 500 mA @ 12 Vdc 250 mA @ 24 Vdc si a vista IP 40 2,02 Kg Con LED si a vista IP 40 4,26 Kg Con LED Code Notes 1392-A 500 Kg / 4900 N 12-24 Vdc 500 mA @ 12 Vdc 250 mA @ 24 Vdc 1395-A 2 x 500 Kg / 9800 N 12-24 Vdc 1 A @ 12 Vdc 500 mA @ 24 Vdc si a vista IP 40 8,60 Kg N° 2 controplacche in dotazione 1396-A 500 Kg / 4900 N 12-24 Vdc 500 mA @ 12 Vdc 250 mA @ 24 Vdc no a vista IP 65 4,20 Kg Da esterno in acciaio inox, collegamento a fili 1396-A Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 63 Accessories available for electromagnetic door holders 300-K-BASE • Basefor300Kgelectromagneticcounterplate • Formountingthecounterplateonfirebarrierdoors • Material:die-castaluminium • ProvidedwithM8screwwithdampingwasher 500-K-BASE • Basefor500Kgelectromagneticcounterplate • Formountingthecounterplateonfirebarrierdoors • Material:die-castaluminium • ProvidedwithM8screwwithdampingwasher 300-K-STL • “L”shapedbrackettomount300Kgelectromagnets • Formountingtheelectromagnetonverticalsurfacesofthe door frame • Material:annealedaluminium 500-K-STL • “L”shapedbrackettomount500Kgelectromagnets • Formountingtheelectromagnetonverticalsurfacesofthe door frame • Material:annealedaluminium 300-K-STU-E • “U”shapedbracketfor300Kgcounterplate–anodized aluminium • Formountingthecounterplateon10-14mmthickglazedfixed doorframes • RequiresalsoLshapedbracketcode300KSTLfor300Kg electromagnet door holder • Providedwith:3mountingdowels,5M5screws,galvanized steel protection plate, 2 rubber seals, socket head screw 500-K-STU-E • “U”shapedbracketfor500Kgcounterplate–anodized aluminium • Formountingthecounterplateon10-14mmthickglazedfixed doorframes • RequiresalsoLshapedbracketcode500KSTLfor500Kg electromagnet door holder • Providedwith:3mountingdowels,5M5screws,galvanized steel protection plate, 2 rubber seals, socket head screw Order codes Code Description Pcs./package. Package weight Applicability 300-K-BASE Base for 300 Kg electromagnet counter plate 1 0,22 Kg 500-K-BASE Base for 500 Kg electromagnet counter plate 1 0,32 Kg 1392-A, 1395-A, 1396-A 300-K-STL L-shaped bracket to mount 300 Kg electromagnets 1 0,27 Kg 1388-A 500-K-STL L-shaped bracket to mount 500 Kg electromagnets 1 0,39 Kg 1392-A, 1395-A 300-K-STU-E U Bracket to mount 300 Kg electromagnets on glazed doors 1 0,56 Kg 1388-A 500-K-STU-E U Bracket to mount 500 Kg electromagnets on glazed doors 1 0,70 Kg 1392-A, 1395-A, 1396-A 64 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 1388-A Accessories available for electromagnetic door holders 300-K-STZ • “Z”shapedbracketfor300Kgelectromagnetdoorholder complete with “L” shaped bracket – anodized aluminium • Formountingtheplatewithelectromagnetplacedoutsidethe door opening (e.g. with “L” shaped bracket) • Consistingof2Lshapedbrackets • Providedwith:6M5screws,M8screwwithdampingwasher 500-K-STZ • “Z”shapedbracketfor500Kgelectromagnetdoorholder complete with “L” shaped bracket – anodized aluminium • Formountingtheplatewithelectromagnetplacedoutsidethe door opening (e.g. with “L” shaped bracket) • Consistingof2Lshapedbrackets • Providedwith:6M5screws,M8screwwithdampingwasher 2495-CSA • Universalglassbreakemergencybutton • Suitabletoreleaseelectromagnetdoorholders • Dualchangeovercontact • IPDegreeIP54 • Material:thermoplastic,whitecolour • Connection:clampingscrews • Providedwithleadsealabletransparentprotectioncover • Availableingreencolour,code2495-V • Spareglasscode2472-U 2498-R • Controlboardforemergencydoorswithtimer • Settabletimercardfrom0.5to120s,withdelayedrelayupon release or excitation through external command • Powersupply12-24Vdc • Consumptionfrom3to20mAwithexcitedrelay(@12Vdc) • Emergencybuttonincluded,type2495-CSAwithdual changeover contact • SparekeysetcodeCSA-07980 • Code07980:keylockspare Order codes Code Description Pcs./package Package weight Applicability 300-K-STZ “Z”brackettomount300Kgcounterplate 1 0,60 Kg 1388-A 500-K-STZ “Z”brackettomount500Kgcounterplate 1 0,60 Kg 1392-A, 1395-A, 1396-A 2495-CSA Glass break emergency button 1 0,18 Kg All electromagnetic door holders 2498-R Control board with timer 1 0,78 Kg All electromagnetic door holders Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 65 Technical information STANDARDS Standards and regulations for security systems and for the products featured in the catalogue are the domain of CEI (Italian Electro technical Committee) Technical Committee (TC) 79 and of CENELEC Technical Committee 79. For the realization of such systems the CEI 64-8 holds. Italian standards CEI 79-2 Intruder, hold up and anti attack alarm systems: Specific requirements for apparatus CEI 79-3 Intruder, hold up and anti attack alarm systems: Specific requirements for intruder installations CEI 79-4 Intruder, hold up and anti attack alarm systems: Specific requirements for access control CEI 79-16 Intruder, hold up and anti attack alarm systems: Specific requirements for radio wireless system CEI 64-8 Electric systems with rated voltage not above 1000 Vac and 1500 Vdc IMQ Alarm Certification. The Italian quality certification institute IMQ (Istituto Italiano del Marchio di Qualità) issues CEI compliance certifications and the relevant authorization to apply the IMQ brand. IMQ-certified equipment is controlled both during certification and production. Performance standards. CEI 79-2 and 79-3 standards attribute three security levels to each component: the highest level is the highest security. These levels determine the overall security standard of the system. New European Standards CENELEC received from the European Union (EU) the mandate for developing a series of standards including those named EN 50131: Alarm systems - Intrusion and hold-up systems. Once ratified, all the EN standards must be implemented by the national committee, and to this aim they have a deadline date for any conflicting national standards to be either withdrawn or amended. As a consequence the series of standards EN 50131, will gradually replace or amend the national standards CEI 79-2, 79-3, etc. The table below lists the main standards already published or in course of publication Standard Title Deadline date for the EN to be implemented Deadline date for the national standards contrasting the EN must be withdrawn at the national level through the publication of an identical national standard or by adopting it 01/05/2012 EN 50131-1:2006/A1:2009 Alarm systems - Intrusion and hold-up systems - Part 1: System requirements EN 50131-2-2:2008 Alarm systems - Intrusion and hold-up systems - Part 2-2: Intrusion detectors - Passive infrared detectors 01/12/2008 01/12/2010 EN 50131-2-3:2008 Alarm systems - Intrusion and hold-up systems - Part 2-3: Requirements for microwave detectors 01/05/2009 01/05/2011 EN 50131-2-4:2008 Alarm systems - Intrusion and hold-up systems - Part 2-4: Requirements for combined passive infrared and microwave detectors 01/12/2008 01/12/2010 EN 50131-2-5:2008 Alarm systems - Intrusion and hold-up systems - Part 2-5: Requirements for combined passive infrared and ultrasonic detectors 01/05/2009 01/05/2011 EN 50131-2-6:2008 Alarm systems - Intrusion and hold-up systems - Part 2-6: Opening contacts (magnetic) 01/05/2009 01/05/2011 prEN 50131-2-7-1 Alarm systems - Intrusion and hold-up systems - Part 2-7-1: Intrusion detectors - Glass break detectors (acoustic) - - prEN 50131-2-7-2 Alarm systems - Intrusion and hold-up systems - Part 2-7-2: Intrusion detectors - Glass break detectors (passive) - - prEN 50131-2-7-3 Alarm systems - Intrusion and hold-up systems - Part 2-7-3: Intrusion detectors - Glass break detectors (active) - - prEN 50131-2-8 Alarm systems - Intrusion and hold-up systems - Part 2-8: Intrusion detectors - Shock detectors - - EN 50131-3:2009 Alarm systems - Intrusion and hold-up systems - Part 3: Control and indicating equipment 01/02/2010 01/02/2012 The new European standards introduce two new concepts based on which the equipment is classified: Protection Grade and Environmental Class, both articulated in 4 levels, with examples provided in the following tables: 66 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Technical information Nomenclature: I&HAS – Intrusion and Hold-up Alarm Systems IP Degree Risk Description I Low Intruders or robbers are expected to have a low understanding of the I&HASs and are equipped with a limited range of tools that are easily available. II Medium low Intruders or robbers are expected to have a limited understanding of the I&HASs and are able to use a generic range of tools and portable instrumentation (e.g. a multimeter). III Medium high Intruders or robbers are expected to be experienced with I&HASs and have a complete range of instrument and portable electronic equipment available. IV High To be used when security has the priority on all other factors. Intruders or robbers are expected to have the capability or the resources to have planned in details the intrusion or robbery action, and have a comprehensive range of equipment available, including means for replacement of I&HAS components. Environmental class Risk Description I Indoor Environmental Influences commonly existing in indoor rooms, where temperature is fully controlled (e.g. in residential or commercial premises). Notes: Temperature is expected to range between +5 °C and +40 °C, with an average relative humidity of about 75% and not subject to condensation. II Indoor General Environmental Influences commonly existing in indoor rooms, where temperature is not fully controlled (e.g. in corridors, halls or stairways, where condensation can start forming on windows and non-heated areas used for storage or in warehouses where heating is intermittent). Notes: Temperature is expected to range between –10 °C and +40 °C, with an average relative humidity of about 75% and not subject to condensation. III Outdoor sheltered or indoor in extreme conditions Environmental Influences commonly existing outdoor, when the I&HAS components are not completely exposed to atmospheric conditions or indoor, under extreme environmental conditions. Notes: Temperature is expected to range between –25 °C and +50 °C, with an average relative humidity of about 75% and not subject to condensation. For 30 days per year it is accepted that the relative humidity can vary between 85% and 95% being not subject to condensation. IV Outdoor General Environmental Influences commonly existing outdoor, when the I&HAS components are completely exposed to atmospheric conditions. Notes: Temperature is expected to range between –25 °C and +60 °C, with an average relative humidity of about 75% and not subject to condensation. For 30 days per year it is accepted that the relative humidity can vary between 85% and 95% being not subject to condensation. IP GRADE The ingress protection for cases/enclosures, according to CEI standards, is indicated by the IP (Ingress Protection) followed by two digits that respectively indicate protection against the penetration of solid bodies (first digit) and water (second digit). If a case is classified only for one kind of protection, the missing digit is replaced by an X (e.g. IP 3X). Description of IP degree First digit protection against the ingress of solid bodies and contact with live components Second digit protection against the ingress of liquids 0 No specific protection. 0 No specific protection. 1 Protected from solid objects larger than 50 mm, e.g. hands 1 Protected from vertically dripping water 2 Protected from solid objects larger than 12 mm, e.g. fingers 2 Protected from 75° to 90° dripping water 3 Protected from solid objects larger than 2,5 mm, e.g. tools 3 Protected from rain at max 60° angle 4 Protected from solid objects larger than 1 mm, e.g. wires or ribbons 4 Protected from water splashes on all sides 5 Protected from the ingress of dust in quantities that might damage the equipment 5 Protected from water jets on all sides 6 Totally dust tight 6 Protected from sea waves or powerful splashing 7 Tight to immersion, it must prevent the ingress of water in quantities that might cause damage 8 Tight to submersion, the equipment is constantly under water In IEC standards, environments are classified with a letter code and a digit according to the characteristic considered (water, solid objects, temperature etc.). The table below lists the classification of environments and the minimum protection degree for components. Environment classification - Water (AD) Code Characteristics Environment classification - Solid objects (AE) IP Degree AD 1 Negligible water (dry indoor environments) IP X0 AD 2 Condensate drops (very humid indoor environments) IP X1 Atomized water dropping (outdoor environments not subject to splashes) Code AE 1 Characteristics IP Degree Negligible presence of dust and small solid objects (home, school, IP 0X office etc.) IP X3 AE 2 Small solid objects IP 3X AD 4 Splashes (environments subject to splashes) IP X4 AE 3 Very small solid objects IP 4X AD 5 Jets (washing rooms) IP X5 AD 6 Waves (on piers) IP X6 AE 4 Dust in significant quantity (cement factory, granary etc.) IP 5X IP 6X AD 7 Immersion (rooms subject to temporary flooding) IP X7 AD 8 Total immersion (underwater rooms) IP X8 AD 3 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 67 Technical information For intruder, hold up and anti attack alarm systems, the IP 3X protection degree must be guaranteed as a minimum. Tests must be carried out according to standard CEI 70-1. The test for the first characteristic digit 3 or 4 is passed if the relevant probe cannot be inserted or, if it penetrates, a sufficient distance is maintained between live parts and hazardous moving parts, and, also, the equipment cannot be inhibited. INTRUDER, HOLD UP AND ANTI ATTACK ALARM SYSTEMS DEFINITIONS A good security system consists of an hold up alarm system combined with an intruder alarm system. Hold up alarm system. Part of a set of predominantly electric and electronic equipment, adequately arranged and connected, suitable to detect and signal breaking attempts to pass physical barriers (e.g. if a roller shutter is protected by a rope contact or a door/window is protected by a magnetic reed contact, system signals the breaking attempt before the thief has passed the physical barrier). Therefore, it is a boundary protection that alerts before the thief has entered. Intruder alarm system. Part of a security system consisting of a set of predominantly electric and electronic equipment, adequately arranged and connected, suitable to detect and signal unauthorized intrusion attempts (e.g. in a room protected by a volumetric sensor, the sensor generates an alarm when the thief is inside the protected area, i.e. inside the house). Detectors (also called sensors or transducers). Devices that can generate electric signals from physical events caused or affected by intrusion, theft and aggression attempts. Passive detectors simply consist of a physical process detector (electromechanical contacts, magnetic contacts, vibration contacts, microphones, heat detectors, passive infrared detectors etc.), while active detectors are made up of an emitter-detector system (microwaves, ultrasounds, active infrared etc.). The detector output signal can be analogue (for pulse operation, the pulse duration must be longer than 500 ms) or logical (sequential or combinatory). Central unit. Device that defines the operating status of system, receives and processes signals from the detectors, activates the devices for alarm generation (acoustic and visual). For the processing of signals from pulse-based analogue detectors, the central unit must generate an alarm only with signals longer than 400 ms. If the signal is shorter than 50 ms, it must be ignored. Control panels. They feed the central unit with the operating status of the system. They can be electromechanical or electronic keys, programmable keypads etc. Signal or alarm devices. They are acoustic (indoor or outdoor sounders) or luminous (beacons). All systems designed to signal an emergency remotely can also be considered as alarm devices. Power supply unit. Device connected to the mains network, designed to supply DC power to the equipment and to load the accumulator batteries that supply energy for backup power in case of voltage drop. Interconnection. Wiring systems to connect the detectors to the central unit and the latter to the alarm devices. Cabling with a section below 0.2 mm2 are not allowed. If the connected equipment must be supplied with electric power, the wire section must be suitable and never below 0.5 mm2. INTRUDER, HOLD UP AND ANTI ATTACK ALARM SYSTEMS CHARACTERISTICS OF COMPONENTS MAGNETIC CONTACTS Reed contact technology. Magnetic contacts are based on the use of reed contacts and permanent magnets. The reed contact, also called reed bulb, consists of two thin metal laminations of ferromagnetic material (e.g. iron-nickel), with low reluctance and tightly sealed into a glass bulb, with an inert gas atmosphere inside. The tight sealing of the contacts protects them from dust, corrosion and oxidization, ensuring an operating life of several tens of millions of operations. The laminations are positioned in such a way that their ends lie opposite to each other, without touching. When a magnetic field, for instance generated by a permanent magnet, gets close to the reed bulb, the lamination ends are charged with opposing magnetic polarity, and when a sufficiently intense magnetic field is generated, the mutual attraction between the opposite poles overcomes the stiffness of the laminations, bending them one against the other and closing the contact. When the influence of the magnetic field is over, the spring effect of the lamination material separates the contact and restores the electric conditions to the previous status. The bulb is normally open (NO), but usually the contact status with near magnet is indicated, so you say that the contact is normally 68 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it Technical information closed (NC) with near magnet. Changeover reed contacts are also available, provided with two laminations (NO and NC) on one side and a common pole lamination (C) on the other. In this case, an approaching magnetic field causes the contact status to change. Changeover reed bulbs are normally less sensitive than NO bulbs (thus, they imply shorter operating distances). The second picture shows the operating diagram of a flush-mounting magnetic contact (however, the diagram applies to all contacts), made up of a reed section and a magnet section. In the reed section, an anti-tampering wire is inserted to prevent violation through the inhibition of wires. As the wire sheathes are all of the same colour, upon installation the anti-tampering wires can be identified as they are the only wires that ensure continuity (or null resistance), when tested with a multimeter with far magnet. NO reed bulb (NC with near magnet) MAGNET REED Alarm contact (NC) Anti-tampering line Changeover reed bulb With near magnet, closed contact Alarm contact (NC) Anti-tampering line With far magnet, open contact Operating distances and positions The distance at which a reed bulb changes status when a magnet approaches is always shorter than the distance at which the reed bulb changes status when the magnet is removed. Therefore, the reed contact works in hysteresis (e.g. when the magnet approaches, the contact closes at 10 mm distance, when the magnet moves away, the contact opens at 13 mm distance). Distances at which the contact switches when the magnet approaches (on) and the distance at which the contact switches when the magnet moves away (off), with the corresponding hysteresis area (hold) are illustrated in the pictures for a magnet where the pole axis is parallel or perpendicular to the contact. The analysis of the operating distance diagrams shows that the magnetic contact can work properly, also in different positions other than axial and parallel. However, the T position must be absolutely avoided, as the contact cannot switch. Operating distance diagram Allowed mounting position T position: WRONG MOUNTING Factors affecting operating distance: • Vicinity of ferromagnetic materials. The vicinity of materials like iron and steel remarkably reduces the operating distances (typically by 50%, but it depends on the shape and type of ferromagnetic material). • Temperature: magnetism reduces as temperature increases. At high temperature, the operating distance is reduced, while at low temperature it increases. Under potential high temperature conditions, above all for polarized contacts with a narrow operating range, the installation distance must be chosen accurately to avoid false alarms at high temperatures. Installing the contacts at 50% of the maximum distance recommended, normally good results are achieved as temperature changes. The operating distances recommended in this catalogue have ±20% tolerance and are measured at room temperature.. High-security contacts: double, triple balancing and interlaced flows Contacts have been developed where a certain number of magnets generate magnetic fields with complex shape. Different reed bulbs connect to these magnetic fields. The system is highly sensitive to external magnetic fields, therefore the perturbation caused by an approaching magnet used for external violation is immediately detected, triggering the alarm. The classification of devices in order of increasing security and according to the magnet and reed bulb configuration is the following: double balancing contacts, triple balancing contacts and interlaced flow contacts. To achieve high performance with these contacts, also special methods for protection against opening and/or removal are adopted. Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 69 Technical information Performance levels The table describes the tests required for the classification of magnetic contacts by performance levels. Protections and tests (X = test required) Case opening (1) Removal (1) Tampering with standard magnet (0, 1 Tesla) Tampering with original magnet Functional verification Immunity to voltage pulses Duration test Liv. I A 1 Liv. II Liv. III X X X X A 2 X X X X A 3 Certification table for magnetic contact detectors (CEI 79-2 standard) (1) not applicable for flush-mounting contacts Duration test 1: 1,400 cycles per 24h Duration test 2: 7,000 cycles per 120h Duration test 3: 14,000 cycles per 240h Immunity to voltage pulses: for grade A: 4 kV Opening test: try to inhibit the system by non-disruptive opening and check that the anti-tampering device triggers the alarm. Removal test: try to remove the system by taking it off the installation surface by at least 10 mm and check that the anti-tampering device triggers the alarm. Tampering test with magnets: put a magnet close to the contact to tamper with it and check that the anti-tampering device triggers the alarm. Connection of magnetic contacts to the central unit A single wire can be used to connect all detectors in series. It is necessary to create two separate series circuits: one for NC contacts and one for the anti-tampering circuit. In the NC circuit, the short circuit of wires does not cause any alarm and, therefore, for specific safety requirements, a balancing resistor must be inserted on the last contact, to obtain a balanced line (a short circuit or the parallel connection of more resistors will change the input resistance value of the central unit, which will be read as an alarm signal). ELECTROMECHANICAL VIBRATION DETECTORS WITH ANALYSIS UNIT These detectors are designed for surface protection and consist of a mechanical contact made up of two sections: one is integral with the case and the other is a mass with high inertia. When stressed, the second part tends to oscillate according to its mechanical inertia features, causing a number of contact interruptions. As the interruption duration is not definite, it is necessary to connect to a suitable analysis card, to allow the generation of an alarm pulse with minimum 500 ms duration. INERTIAL VIBRATION DETECTORS WITH ANALYSIS UNIT These detectors are similar to the electromechanical vibration detectors, but their two or more contacts are integral with the body, while the high-inertia mass is only touching the contacts, causing the circuit to close. Also these detectors require an analysis board. MICROPHONE DETECTORS FOR GLASS WITH ANALYSIS UNIT These are designed for surface protection on glazing and are basically made up of a piezoelectric microphone capsule that detects the frequency generated by breaking glass. They must be connected to an analysis board. OTHER TYPES OF DETECTORS Cooper Csa produces other types of detectors (see catalogue for details) for any requirement, in detail: • Roller shutter lifting rope or rod detectors: detect the lifting of roller shutters/gates • Pressure sensitive mats: to be placed under carpets and deep-pile carpet near doors or windows (at the main entrances and passageways) • Button or foot pedal aggression detectors: they must operate silently and simply not to arouse suspicion; they allow to signal an ongoing aggression • Mercury contacts: detect the achievement of a certain inclination of the surface they are mounted on (normally used on tilting doors and windows) • Heat detectors: detect violation through the fire cutting of armoured doors, safes etc. • Flooding detectors: warn of the flooding of rooms where they are installed SOUNDER AND BEACON ALARM DEVICES Acoustic alarm devices are divided into: • Sounders and hooters for service and control. They must be equipped with battery supply, sturdy container and self-protection level as required • Additional sirens. Battery supply and self-protection not required. Beacons are basically flashlights (which must emit orange light). 70 Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it General sales conditions PREMISE The general sales conditions are applied to each purchase order with exception of written modifications. The forwarding of a purchase order implies the acceptance of the present general sales conditions. The Supplier can change dimensions and structure of the devices from aesthetic or functional point of view without previous communication. PRICES The price list may be changed informing the customers. in case of variations of costs and/or foreign exchange rate. Prices do not include VAT. transport and other accessories costs. ORDERING Purchase orders are accepted with a minimum tax threshold of Euros 300,00. PAYMENT TERMS Payment must be done, unless otherwise indicated in writing, directly to the Supplier according to the terms agreed. In case of payment delay. interest will be applied starting from expired date of invoice until the amount has been settled (Italian law Dlgs 9/12/2002 n. 231. art 5). Payment lack allows the Supplier to interrupt the warranty and to postpone actual shipments. SUPPLY CONTRACT DISSOLUTION In case protests for cheques or bills should be opposed to the Buyer, executive procedures for arrangement with the creditors or bankruptcy, the Supplier reserves the faculty to terminate the contract unilaterally, upon simply providing a written communication to the Buyer. DELIVERY The delivery of products is ex-factory: Cooper Csa srl. • Via A. Meucci. 10 – 20094 Corsico (Milan) - Italy. Contractual delivery terms for the Supplier (established in 10 working days from order receipt) are indicatives and therefore conditional on both the production possibilities and events of force major: claims of damages due to delivery delays will not be accepted. If orders cannot be shipped in time the Supplier will inform the Customer of the new delivery date. Deliveries can be split. SHIPMENT Transport is on Purchaser’s risk even if the forwarder has been chosen by the Supplier or the delivery is CIF. For the shipment of goods by means of a postal parcel, ad additional 5% of the cost will be charged to cover the postal packaging expenses. In case of shipments with an economic value lower than 500 Euros (VAT excluded), or for URGENT delivery, the transportation costs will be charged to the Buyer. COMPLAINT Complaints about quality, quantity, kind of products or defects must be written to the Supplier within 8 days upon receipt of the goods. Afterwards no complaints will be accepted excluding exception of different warranty conditions of the products. Return of goods have to be authorized in writing by the supplier. WARRANTY Warranty is 26 months from the delivery or shipment date and covers manufacturing defects. During warranty period products can be replaced or repaired according to Supplier’s appraisal. The warranty does not cover tampered products repaired by third parties or used in a not conform way. THIRD PARTIES LIABILITY The issuing of a purchase order by the Buyer implies accepting the responsibility to respect law and safety rules in using the products supplied. COMPETENT COURT For any controversy that should arise in executing the supply contract, the competent court shall be the Court of Milan, Italy. Intrusion System Components • Toll Free Number 800-449433 • www.coopercsa.it 71
