Rotary One-touch Fittings
Standard Type/High Speed Type
Series KS/KX
Cassette
The male connector is equipped with a
“tuberotation prevention mechanism”.
Series KS
Blue
Series KX
Blue
Slide bearing
Smooth operation and longer life from an
oil containing slide bearing.
Rotary seal
A special rotary seal minimizes friction while
providing an excellent seal.
Series KX (High speed)
Scraper
Holder
Prevents chips from intruding
into bearing parts.
Standard nickel plated allows copper-free applications.
Rotary seal
Ball bearing
A ball bearing ensures low torque rotation.
Stud
Standard nickel plated allows copper-free applications.
Thread sealant is standard.
Low torque rotation style
Rotary One-touch fittings
Applicable to use for
oscillating and rotating
sections in robots.
Copper-free specifications
Brass parts are all
electroless nickel plated.
Thread seal is standard.
Series KS
(Standard)
X ring shape minimizes
friction while providing an
excellent seal. Seal is fire
and shock proof fluorine
rubber. Proves against high
friction heat in high speed
rotation and longer life.
Ball bearing
A ball bearing ensures low torque
rotation. Stainless steel 440C
improves corrosion resistance.
∗ Other parts’ specifications are same as those
of Series KS.
Applicable Tubing
Tubing material Note)
Tubing O.D.
Nylon, Soft nylon, Polyurethane
ø4, ø6, ø8, ø10, ø12
Note) Use caution about the max. operating pressure for soft nylon and polyurethane.
Specifications
Fluid
Maximum operating pressure
Operating vacuum pressure
Proof pressure
Ambient and fluid temperature
Air
1.0 MPa
–100 kPa
3.0 MPa
–5 to 60°C (No freezing)
JIS B 0203 (Taper thread for piping),
JIS B 0209, class 2 (Metric coarse thread)
Thread
Rotating Torque/Allowable Number of Rotations
Applicable tubing O.D.
Rotating torque (N·m) Note)
Allowable number of rotations
Series KS
Series KX
ø4
0.006
8.4
25
ø6
0.012
8.4
20
ø8
0.014
6.7
20
ø10
0.020
5
16.7
ø12
0.022
4.2
16.7
Note) Rotating torque under pressure 0.5 MPa
Male elbow
Male connector
Principal Parts Material
Model
Body
Stud, Holder, Guide
Chuck, Retainer
Collet, Release button, Snap ring
O-ring, Packing
Rotary seal
Slide bearing
Scraper
Ball bearing
Gasket
15-2-38
Series KS
Series KX
PBT
C3604BD (Electroless nickel plated), Stainless steel 304
Stainless steel (Stainless steel 304) (1) (Retainer (C) of
Series KX: C3604BD (electroless nickel plated))
Polyacetal
NBR
NBR
FPM
Oil-containing polyacetal
—
—
NBR
Bearing steel
Stainless steel 440C
Stainless steel (Stainless steel 304), NBR
Rotary One-touch Fittings
Series
KS/KX
Series KS/Series KX
Model
Male connector
KSH
KXH
Connection thread
ø4
Applicable tubing O.D. (mm)
ø10
ø6
ø8
ø12
M5 x 0.8
M6 x 1
R18
Male elbow
KSL
KXL
R14
K
R38
M
R12
H
M5 x 0.8
D
M6 x 1
MS
R18
T
R14
VMG
R38
R12
Precautions
Be sure to read before handling. Refer to pages 15-18-3 to 15-18-4 for
Safety Instructions and Common Precautions on the products mentioned
in this catalog, and refer to pages 15-1-10 to 15-1-11 for Precautions on
every series.
Caution
1. Implement the tube piping in such a way that laterial load should not be applied on the
ball bearings, otherwise it may adversely affect the life expectancy.
A flexible polyurethane tube is recommended when the lateral load is applied.
15-2-39
Series
KS/KX
Male connector: KSH (Standard)
<M5, M6>
<R>
H
Applicable Connection
(width
Model
tubing O.D. thread
across D1
flats)
(mm)
R
M5 x 0.8 KSH04-M5
8
10.4
M6 x 1 KSH04-M6
4
18
12
KSH04-01S
M5 x 0.8 KSH06-M5
8
M6 x 1 KSH06-M6
6
12.8
18
KSH06-01S
14
14
KSH06-02S
18
KSH08-01S
14
8
17 15.2
KSH08-02S
38
KSH08-03S
14
KSH10-02S
38
10
22 18.5
KSH10-03S
12
KSH10-04S
38
KSH12-03S
24 20.9
12
12
KSH12-04S
D2
12
14
17
22
24
L
36.5
37
38
37.5
38
39.5
42.5
44
47
48
54
55
57.5
57
60
A
Min. Effective area
Weight
(mm2)
M port
(g)
size Nylon Urethane
33
9
34
33.5
34
35.5
36.5
40
41
41.5
48
48.5
49.5
50.5
52
16
17
2.5
4.0
2.5
3
4.0
5.6
4
10.4
18.5 6
26.1
21
36.3
22
7
8
46.1
4.0
14
4.0
12
5.6
17
10.4
23
23
18.0 29
37
55
29.5 63
81
75
16.1
92
<M5, M6>
Applicable
tubing
Connection thread
<R>
Applicable
tubing
A∗
∗ Reference dimensions after R thread installation.
Connection thread
(With seal)
Male Connector: KXH (High speed)
<M5, M6>
Applicable Connection
tubing O.D. thread
(mm)
R
4
6
<R>
8
10
12
Model
M5 x 0.8 KXH04-M5
M6 x 1 KXH04-M6
18
KXH04-01S
M5 x 0.8 KXH06-M5
M6 x 1 KXH06-M6
18
KXH06-01S
14
KXH06-02S
18
KXH08-01S
14
KXH08-02S
38
KXH08-03S
14
KXH10-02S
38
KXH10-03S
12
KXH10-04S
38
KXH12-03S
12
KXH12-04S
H
(width
across D1 D2
flats)
8
12
8
14
17
22
24
L
38.5
39
40
39.5
40
12.8 15
42
45
46
15.2 18 49
50
58
18.5 23.5 59
62
60
20.9 26
63
10.4 13
A
35
Min. Effective area
Weight
(mm2)
M port
(g)
size Nylon Urethane
16
2.5 4.0
4.0
2.5 4.0
3
5.6
4.0
5.6
17
38
4
39
42
43 18.5 6
44
52
21
53
54
22
55
Applicable tubing
11
16
36
36
<M5, M6>
7
8
15
20
26
28
26.1 18.0 34
42
68
36.3 29.5 76
94
88
46.1 46.1
105
10.4 10.4
<R>
Applicable tubing
A∗
∗ Reference dimensions after R thread installation.
Connection
thread
Connection thread
(With seal)
15-2-40
Rotary One-touch Fittings
Series
KS/KX
Male Elbow: KSL (Standard)
<M5, M6>
<R>
H
Applicable Connection
(width
tubing O.D. thread
Model
across D1 D2 L1
(mm)
R
flats)
M5 x 0.8 KSL04-M5
8
M6 x 1 KSL04-M6
4
10.4 12 21
18
KSL04-01S 12
M5 x 0.8 KSL06-M5
8
M6 x 1 KSL06-M6
12.8 14 23
6
18
KSL06-01S
14
14
KSL06-02S
18
KSL08-01S
14
8
KSL08-02S 17 15.2 17 26
38
KSL08-03S
14
KSL10-02S
38
10
KSL10-03S 22 18.5 22 31.5
12
KSL10-04S
38
KSL12-03S
24 20.9 24 34
12
12
KSL12-04S
L2
20.5
21
22
21
21.5
23
26
26.5
29.5
31
34
35
38
36.5
39.5
Min. Effective area
Weight
(mm2)
M port
(g)
size Nylon Urethane
A
22
16
23.5
23.5
24
25.5
26.5
30
31
32
37.5
38
39.5
40.5
42
2.5
3.5
3.5
<M5, M6>
9
14
17
2.5
3
3.5
5.0
4
8.6
18.5 6
21.6
21
7
30.5
22
8
35.1
3.5
12
5.0
17
8.6
23
23
14.9 29
38
56
25.0 64
82
76
35.1
93
K
Applicable tubing
M
Connection thread
<R>
H
D
∗ Reference dimensions after R thread installation.
MS
T
∗
VMG
Applicable tubing
Connection thread
(With seal)
Male Elbow: KXL (High speed)
<M5, M6>
Applicable Connection
tubing O.D. thread
(mm)
R
4
6
<R>
8
10
12
Model
M5 x 0.8 KXL04-M5
M6 x 1 KXL04-M6
18
KXL04-01S
M5 x 0.8 KXL06-M5
M6 x 1 KXL06-M6
18
KXL06-01S
14
KXL06-02S
18
KXL08-01S
14
KXL08-02S
38
KXL08-03S
14
KXL10-02S
38
KXL10-03S
12
KXL10-04S
38
KXL12-03S
12
KXL12-04S
H
(width
across D1 D2 L1 L2
flats)
22.5
8
10.4 13 22 23
12
24
23.5
8
24
12.8 15 24
25
14
28
29
17 15.2 18 27 32
33
38
22 18.5 23.5 32 39
42
40
24 20.9 26 35
43
A
24
Min. Effective area
Weight
(mm2)
M port
size Nylon Urethane (g)
16
2.5 3.5
25
26
2.5 3.5
5.0
3
17
28
4
29
32
33 18.5 6
34
42
21
43
44
22
45
7
8
8.6
21.6
30.5
35.1
3.5
<M5, M6>
11
16
3.5
15
5.0
20
8.6
26
28
14.9 34
43
69
25.0 77
95
89
35.1
106
∗ Reference dimensions after R thread installation.
Applicable tubing
Connection thread
<R>
Applicable tubing
Connection thread
15-2-41
Inch-size Rotary One-touch Fittings
Standard Type
Series
KS
Applicable Tubing: Inch Size
Cassette (Red)
Slide bearing
The male connector is
equipped with a “tube rotation
prevention mechanism.”
Smooth operation and longer life from an
oil containing slide bearing.
Rotary seal
A special rotary seal minimizes friction
while providing an excellent seal.
Holder
Standard nickel plated allows copper-free
applications.
Ball bearing
A ball bearing ensures low torque rotation.
Stud
Standard nickel plated allows copper-free
applications.
Thread seal is standard.
Low-torque rotation style
rotary One-touch fittings
Applicable to use for
oscillating and rotating
sections in robots.
Applicable to non-copper
type (With electroless nickel
plated)
Thread seal is standard.
Applicable Tubing
Tubing material Note)
Nylon, Soft nylon, Polyurethane
ø 5 32 ", ø1 4 ", ø 5 16 ", ø 3 8 "
Tubing O.D.
Note) Monitor max.operating pressure for soft nylon and polyurethane tubing.
Specification
Fluid
Maximum operating pressure
Operating vacuum pressure
Proof pressure
Air
1.0 MPa
–100 kPa
3.0 MPa
–5 to 60°C (No freezing)
Ambient and fluid temperature
ANSI/ASMEB1.20.1-1983 (NTP thread)
JIS B 0212 2A, Class 2B (UNF thread)
Thread
Rotating Torque/Allowable Number of Rotations
Applicable tubing O.D.
Rotating torque (N·m) Note)
Allowable number of rotations (S-1)
Male elbow
Male connector
ø1 4 "
ø 5 16"
ø 3 8"
0.012
0.014
0.020
8.3
8.3
6.7
5
Note) Rotating torque under pressure 0.5 MPa
Principal Parts Material
Body
Stud, Holder, Guide
Chuck, Retainer
Collet, Release button, Snap ring
O-ring, Packing
Rotary seal
Slide bearing
Scraper
Ball bearing
Gasket
15-4-36
ø 5 32 "
0.006
PBT
Stainless steel 304, C3604BD (With electroless nickel plated)
Stainless steel 304
Polyacetal
NBR
NBR
Oil-containing polyacetal
—
Bearing steel
Stainless steel 304, NBR
Inch-size Rotary One-touch Fittings
Series
KS
Series KS
Model
Male connector
KSH
Male elbow
KSL
Connection thread
ø 5 32"
Applicable tubing O.D. (inch)
ø1 4 "
ø 5 16"
ø 3 8"
10-32 UNF
NPT
18
NPT
14
NPT
38
K
M
10-32 UNF
NPT
18
NPT
14
NPT
38
H
D
MS
T
VMG
Precautions
Be sure to read before handling. Refer to pages 15-18-3 to 15-18-4 for
Safety Instructions and Common Precautions on the products mentioned
in this catalog, and refer to pages 15-1-10 to 15-1-11 for Precautions on
every series.
Caution
1. Implement the tube piping in such a way that the lateral load should not be applied.
Although ball bearing is adopted, however if the lateral load were applied on it, it may
adversely affect the life expectancy. A flexible polyurethan tube is recommended when
the lateral load is applied.
15-4-37
Series
KS
Male Connector: KSH (Standard)
<UNF>
Applicable Connection
tubing
thread
O.D.
UNF
(inch)
NPT
5 32
14
5 16
38
H
Min. Effective2 area Weight
(Width
(mm )
∗ M port
across D1 D2 L A
size Nylon Urethane (g)
flats)
9
10-32 UNF KSH03-32 8
36.5 33
16 2.5 4.0 4.0
10.4 12
18
14
KSH03-34S 12.7
38.5 34.5
18
17
KSH07-34S
39.5 35.5
13.4 10.4
14.29 13.2 14
17 4
14
23
KSH07-35S
42.5 36.5
18
23
KSH09-34S
44 40
18.5
18.0
26.1
15.2
6
17.46
17
14
29
KSH09-35S
47 41
14
55
KSH11-35S
54 48
22.23 17.9 22
29.5
36.3
7
21
38
63
KSH11-36S
55 48.5
∗ Reference dimensions after NPT thread installation.
<UNF>
Model
Applicable
tubing
Connection thread
<NPT>
<NPT>
Applicable
tubing
Connection thread
(With seal)
Male Elbow: KSL (Standard)
<UNF>
Applicable Connection
tubing
thread
O.D.
UNF
(inch)
NPT
5 32
14
5 16
38
<NPT>
H
Min. Effective 2area Weight
(Width
(mm )
∗
across D1 D2 L1 L2 A M port
size
Nylon
Urethane (g)
flats)
9
10-32 UNF KSL03-32 8
20.5 22
16 2.5 3.5 3.5
10.4 12 21
18
14
KSL03-34S 12.7
22 23.5
18
17
KSL07-34S
23 25.5
8.6 8.6
14.29 13.2 14 23.5
17 4
14
23
KSL07-35S
26 26.5
18
23
KSL09-34S
26.5 30
18.5
14.9
15.2
6
21.6
17.46
17
26
14
29
KSL09-35S
29.5 31
14
56
KSL11-35S
34 37
22.23 17.9 22 31.5
25.0
7
30.5
21
38
64
KSL11-36S
35 38
∗ Reference dimensions after NPT thread installation.
Model
<UNF>
Applicable tubing
Connection thread
<NPT>
Applicable tubing
Connection thread
(With seal)
15-4-38
Safety Instructions
These safety instructions are intended to prevent a hazardous situation and/or
equipment damage. These instructions indicate the level of potential hazard by labels of
"Caution", "Warning" or "Danger". To ensure safety, be sure to observe ISO 4414 Note 1),
JIS B 8370 Note 2) and other safety practices.
Caution : Operator error could result in injury or equipment damage.
Warning : Operator error could result in serious injury or loss of life.
Danger :
In extreme conditions, there is a possible result of serious injury or loss of life.
Note 1) ISO 4414: Pneumatic fluid power--General rules relating to systems.
Note 2) JIS B 8370: General Rules for Pneumatic Equipment
Warning
1. The compatibility of pneumatic equipment is the responsibility of the person
who designs the pneumatic system or decides its specifications.
Since the products specified here are used in various operating conditions, their compatibility for the
specific pneumatic system must be based on specifications or after analysis and/or tests to meet your
specific requirements. The expected performance and safety assurance will be the responsibility of the
person who has determined the compatibility of the system. This person should continuously review
the suitability of all items specified, referring to the latest catalog information with a view to giving due
consideration to any possibility of equipment failure when configuring a system.
2. Only trained personnel should operate pneumatically operated machinery
and equipment.
Compressed air can be dangerous if an operator is unfamiliar with it. Assembly, handling or repair of
pneumatic systems should be performed by trained and experienced operators.
3. Do not service machinery/equipment or attempt to remove components until
safety is confirmed.
1. Inspection and maintenance of machinery/equipment should only be performed once measures to
prevent falling or runaway of the driver objects have been confirmed.
2. When equipment is to be removed, confirm the safety process as mentioned above. Cut the supply
pressure for this equipment and exhaust all residual compressed air in the system.
3. Before machinery/equipment is restarted, take measures to prevent shooting-out of cylinder piston
rod, etc.
4. Contact SMC if the product is to be used in any of the following conditions:
1. Conditions and environments beyond the given specifications, or if product is used outdoors.
2. Installation on equipment in conjunction with atomic energy, railway, air navigation, vehicles,
medical equipment, food and beverages, recreation equipment, emergency stop circuits, clutch and
brake circuits in press applications, or safety equipment.
3. An application which has the possibility of having negative effects on people, property, or animals,
requiring special safety analysis.
15-18-3
Common Precautions
Be sure to read before handling.
For detailed precautions on every series, refer to main text.
Selection
Warning
1. Confirm the specifications.
Products represented in this catalog are designed for use in
compressed air appllications only (including vacuum), unless
otherwise indicated.
Do not use the product outside their design parameters.
Please contact SMC when using the products in applications
other than compressed air (including vacuum).
Mounting
Warning
1. Instruction manual
Install the products and operate them only after reading the
instruction manual carefully and understanding its contents.
Also keep the manual where it can be referred to as
necessary.
4. Use clean air
If the compressed air supply is contaminated with chemicals,
cynthetic materials, corrosive gas, etc., it may lead to break
down or malfunction.
Operating Environment
Warning
1. Do not use in environments where the product
is directly exposed to corrosive gases,
chemicals, salt water, water or steam.
2. Do not expose the product to direct sunlight
for an extended period of time.
3. Do not use in a place subject to heavy
vibrations and/or shocks.
4. Do not mount the product in locations where it
is exposed to radiant heat.
Maintenance
2. Securing the space for maintenance
When installing the products, please allow access for
maintenance.
3. Tightening torque
When installing the products, please follow the listed torque
specifications.
Piping
Caution
1. Before piping
Make sure that all debris, cutting oil, dust, etc, are removed
from the piping.
2. Wrapping of pipe tape
When screwing piping or fittings into ports, ensure that chips
from the pipe threads or sealing material do not get inside the
piping. Also, when the pipe tape is used, leave 1.5 to 2 thread
ridges exposed at the end of the threads.
Air Supply
Warning
1. Operating fluid
Please consult with SMC when using the product in
applications other than compressed air (including vacuum).
Regarding products for general fluid, please ask SMC about
applicable fluids.
2. Install an air dryer, aftercooler, etc.
Excessive condensate in a compressed air system may cause
valves and other pneumatic equipment to malfunction.
Installation of an air dryer, after cooler etc. is recommended.
3. Drain flushing
If condensate in the drain bowl is not emptied on a regular
basis, the bowl will over flow and allow the condensate to
enter the compressed air lines.
If the drain bowl is difficult to check and remove, it is
recommended that a drain bowl with the auto-drain option be
installed.
For compressed air quality, refer to “Air Preparation
Equipment” catalog.
15-18-4
Warning
1. Maintenance procedures are outlined in the
operation manual.
Not following proper procedures could cause the product to
malfunction and could lead to damage to the equipment or
machine.
2. Maintenance work
If handled improperly, compressed air can be dangerous.
Assembly, handling and repair of pneumatic systems should
be performed by qualified personnel only.
3. Drain flushing
Remove drainage from air filters regularly. (Refer to the
specifications.)
4. Shut-down before maintenance
Before attempting any kind of maintenance make sure the
supply pressure is shut of and all residual air pressure is
released from the system to be worked on.
5. Start-up after maintenance and inspection
Apply operating pressure and power to the equipment and
check for proper operation and possible air leaks. If operation
is abnormal, please verify product set-up parameters.
6. Do not make any modifications to be product.
Do not take the product apart.
Quality Assurance Information
(ISO 9001, ISO 14001)
Reliable quality of products in the global market
To enable our customers throughout
the world to use our products with
even greater confidence, SMC has
obtained certification for international
standards “ISO 9001” and “ISO
14001”, and created a complete
structure for quality assurance and
environmental
controls.
SMC
products pursue to meet its
customers’ expectations while also
considering company’s contribution in
society.
SMC’s quality control system
Make customers our
first priority, offering
them reliable and
friendly service.
Produce the highest
quality with the
participation of all
employees.
Create new
products using the
latest technology,
and offer the finest
products in a
timely manner.
Quality policies
Market research
Product planning
After service
Sales coordination
Quality management system
ISO 9001
This is an international standard for quality control
and quality assurance. SMC has obtained a large
number of certifications in Japan and overseas,
providing assurance to our customers throughout
the world.
Quality system
education
Training of
suppliers
Research
Education
Design
Training
Development
Production
New product evaluation
Reliability design
Reliability testing
New technical
development
Process control
Inspection, testing, etc.
Initial production control
Quality control activities
Environmental management system
ISO 14001
This is an international standard related to
environmental management systems and
environmental inspections. While promoting
environmentally friendly automation technology,
SMC is also making diligent efforts to preserve
the environment.
15-18-5
SMC Product Conforming to Inter
SMC products complying with EN/ISO, CSA/UL standards are supporting
CE Mark
The CE mark indicates that machines and components meet essential requirements of all the EC Directives
applied.
It has been obligatory to apply CE marks indicating conformity with EC Directives when machines and
components are exported to the member Nations of the EU.
Once “A manufacturer himself” declares a product to be safe by means of CE marking (declaration of
conformity by manufacturer), free distribution inside the member Nations of the EU is permissible.
CE Mark
SMC provides CE marking to products to which EMC and Low Voltage Directives have been applied, in
accordance with CETOP (European hydraulics and pneumatics committee) guide lines.
As of February 1998, the following 18 countries will be obliged to conform to CE mark legislation
Iceland, Ireland, United Kingdom, Italy, Austria, Netherlands, Greece, Liechtenstein, Sweden, Spain, Denmark,
Germany, Norway, Finland, France, Belgium, Portugal, Luxembourg
EC Directives and Pneumatic Components
• Machinery Directive
The Machinery Directive contains essential health and safety requirements for machinery, as applied to
industrial machines e.g. machine tools, injection molding machines and automatic machines. Pneumatic
equipment is not specified in Machinery Directive. However, the use of SMC products that are certified as
conforming to EN Standards, allows customers to simplify preparation work of the Technical Construction File
required for a Declaration of Conformity.
• Electromagnetic Compatibility (EMC) Directive
The EMC Directive specifies electromagnetic compatibility. Equipment which may generate electromagnetic
interference or whose function may be compromised by electromagnetic interference is required to be immune
to electromagnetic affects (EMS/immunity) without emitting excessive electromagnetic affects (EMI/emission).
• Low Voltage Directive
This directive is applied to products, which operate above 50 VAC to 1000 VAC and 75 VDC to 1500 VDC
operating voltage, and require electrical safety measures to be introduced.
• Simple Pressure Vessels Directive
This directive is applied to welded vessels whose maximum operating pressure (PS) and volume of vessel (V)
exceed 50 bar/L. Such vessels require EC type examination and then CE marking.
15-18-6
SMC Product Conforming to International Standards
national Standards
you to comply with EC directives and CSA/UL standards.
Mark of compliance
for CSA/UL
Mark of compliance
for CSA
CSA Standards & UL Standards
UL and CSA standards have been applied in North America (U.S.A. and Canada) symbolizing safety of electric
products, and are defined to mainly prevent danger from electric shock or fire, resulting from trouble with
electric products. Both UL and CSA standards are acknowledged in North America as the first class certifying
body. They have a long experience and ability for issuing product safety certificate. Products approved by CSA
or UL standards are accepted in most states and governments beyond question.
Since CSA is a test certifying body as the National Recognized Testing Laboratory (NRTL) within the
jurisdiction of Occupational Safety and Health Administration (OSHA), SMC was tested for compliance with
CSA Standards and UL Standards at the same time and was approved for compliance with the two Standards.
The above CSA NRTL/C logo is described on a product label in order to indicate that the product is approved
by CSA and UL Standards.
TSSA (MCCR) Registration Products
TSSA is the regulation in Ontario State, Canada. The products that the operating pressure is more than 5 psi
(0.03 MPa) and the piping size is bigger than 1 inch. fall into the scope of TSSA regulation.
Products conforming to CE Standard
With CE symbol for simple visual recognition
In this catalog each accredited product series is indicated with a
CE mark symbol. However, in some cases, every available
models may not meet CE compliance. Please visit our web site
for the latest selection of available models with CE mark.
http://www.smcworld.com
15-18-7
SMC’s Global Service Network
America
Europe
U.S.A. SMC Corporation of America
3011 North Franklin Road Indianapolis, IN 46226, U.S.A.
TEL: 317-899-4440 FAX: 317-899-3102
U.K. SMC Pneumatics (U.K.) Ltd.
Vincent Avenue, Crownhill, Milton Keynes, MK8 0AN, Backinghamshire, U.K.
TEL: 01908-563888 FAX: 01908-561185
CANADA SMC Pneumatics (Canada) Ltd.
6768 Financial Drive Mississauga, Ontario, L5N 7J6 Canada
TEL: 905-812-0400 FAX: 905-812-8686
GERMANY SMC Pneumatik GmbH
Boschring 13-15 D-63329 Egelsbach, Germany
TEL: 06103-4020 FAX: 06103-402139
MEXICO SMC Corporation (Mexico), S.A. DE C.V.
Carr. Silao-Trejo K.M. 2.5 S/N, Predio San Jose del Duranzo
C.P. 36100, Silao, Gto., Mexico
TEL: 472-72-2-55-00 FAX: 472-72-2-59-44/2-59-46
ITALY SMC Italia S.p.A.
Via Garibaldi 62 I-20061 Carugate Milano, Italy
TEL: 02-9271365 FAX: 02-9271365
CHILE SMC Pneumatics (Chile) S.A.
Av. La Montaña 1,115 km. 16,5 P. Norte Parque
Industrial Valle Grande, Lampa Santiago, Chile
TEL: 02-270-8600 FAX: 02-270-8601
ARGENTINA SMC Argentina S.A.
Teodoro Garcia 3860 (1427) Buenos Aires, Argentina
TEL: 011-4555-5762 FAX: 011-4555-5762
BOLIVIA SMC Pneumatics Bolivia S.R.L.
Avenida Beni Numero 4665
Santa Cruz de la Sierra-Casilla de Correo 2281, Bolivia
TEL: 591-3-3428383 FAX: 591-3-3449900
VENEZUELA SMC Neumatica Venezuela S.A.
Apartado 40152, Avenida Nueva Granada, Edificio Wanlac,
Local 5, Caracas 1040-A, Venezuela
TEL: 2-632-1310 FAX: 2-632-3871
FRANCE SMC Pneumatique S.A.
1 Boulevard de Strasbourg, Parc Gustave Eiffel, Bussy Saint Georges, F-77600
Marne La Vallee Cedex 3 France
TEL: 01-64-76-10-00 FAX: 01-64-76-10-10
SWEDEN SMC Pneumatics Sweden AB
Ekhagsvägen 29-31, S-141 05 Huddinge, Sweden
TEL: 08-603-07-00 FAX: 08-603-07-10
SWITZERLAND SMC Pneumatik AG
Dorfstrasse 7, Postfach 117, CH-8484 Weisslingen, Switzerland
TEL: 052-396-3131 FAX: 052-396-3191
AUSTRIA SMC Pneumatik GmbH (Austria)
Girakstrasse 8, A-2100 Korneuburg, Austria
TEL: 0-2262-6228-0 FAX: 0-2262-62285
SPAIN SMC España, S.A.
Zuazobidea 14 Pol. Ind. Júndiz 01015 Vitoria, Spain
TEL: 945-184-100 FAX: 945-184-510
PERU (Distributor) IMPECO Automatizacion Industrial S.A.
AV. Canevaro 752, Lince, Lima, Peru
TEL: 1-471-6002 FAX: 1-471-0935
IRELAND SMC Pneumatics (Ireland) Ltd.
2002 Citywest Business Campus, Naas Road, Saggart, Co. Dublin, Ireland
TEL: 01-403-9000 FAX: 01-466-0385
URUGUAY (Distributor) BAKO S.A.
Galicia 1650 esq. Gaboto C.P. 11200, Montevideo, Uruguay
TEL: 2-401-6603 FAX: 2-409-4306
NETHERLANDS (Associated company) SMC Pneumatics BV
De Ruyterkade 120, NL-1011 AB Amsterdam, Netherlands
TEL: 020-5318888 FAX: 020-5318880
BRAZIL SMC Pneumaticos Do Brasil Ltda.
Rua. Dra. Maria Fidelis, nr. 130, Jardim Piraporinha-Diadema-S.P.
CEP: 09950-350, Brasil
TEL: 11-4051-1177 FAX: 11-4071-6636
GREECE (Distributor) S.Parianopoulos S.A.
7, Konstantinoupoleos Street 11855 Athens, Greece
TEL: 01-3426076 FAX: 01-3455578
COLOMBIA (Distributor) Airmatic Ltda.
Calle 18 69-05 Apart. Aereo 081045 Santa Fe de Bogotá, Colombia
TEL: 1-424-9240 FAX: 1-424-9260
DENMARK SMC Pneumatik A/S
Knudsminde 4 B DK-8300
Odder, Denmark
TEL: 70252900 FAX: 70252901
15-18-20
SMC’s Global Service Network
Europe
Oceania/Asia
FINLAND SMC Pneumatics Finland OY
PL72, Tiistinniityntie 4, SF-02231 ESP00, Finland
TEL: 09-8595-80 FAX: 09-8595-8595
AUSTRALIA SMC Pneumatics (Australia) Pty.Ltd.
14-18 Hudson Avenue Castle Hill NSW 2154, Australia
TEL: 02-9354-8222 FAX: 02-9894-5719
NORWAY SMC Pneumatics Norway A/S
Vollsveien 13C, Granfoss Næringspark N-1366 LYSAKER, Norway
TEL: 67-12-90-20 FAX: 67-12-90-21
NEW ZEALAND SMC Pneumatics (New Zealand) Ltd.
8C Sylvia Park Road Mt.Wellington Auckland, New Zealand
TEL: 09-573-7007 FAX: 09-573-7002
BELGIUM (Distributor) SMC Pneumatics N.V./S.A.
Nijverheidsstraat 20 B-2160 Wommelgem Belguim
TEL: 03-355-1464 FAX: 03-355-1466
TAIWAN SMC Pneumatics (Taiwan) Co.,Ltd.
17, Lane 205, Nansan Rd., Sec.2, Luzhu-Hsiang, Taoyuan-Hsien, TAIWAN
TEL: 03-322-3443 FAX: 03-322-3387
POLAND SMC Industrial Automation Polska Sp.z.o.o.
ul. Konstruktorska 11A, PL-02-673 Warszawa, Poland
TEL: 022-548-5085 FAX: 022-548-5087
HONG KONG SMC Pneumatics (Hong Kong) Ltd.
29/F, Clifford Centre, 778-784 Cheung, Sha Wan Road, Lai Chi Kok, Kowloon,
Hong Kong
TEL: 2744-0121 FAX: 2785-1314
TURKEY (Distributor) Entek Pnömatik San.ve Tic. Ltd. Sti
Perpa Tic. Merkezi Kat:11 No.1625 80270 Okmeydani Istanbul, Türkiye
TEL: 0212-221-1512 FAX: 0212-221-1519
RUSSIA SMC Pneumatik LLC.
36/40 Sredny prospect V.O. St. Petersburg 199004, Russia
TEL: 812-118-5445 FAX: 812-118-5449
CZECH SMC Industrial Automation CZ s.r.o.
Hudcova 78a, CZ-61200 Brno, Czech Republic
TEL: 05-4121-8034 FAX: 05-4121-8034
HUNGARY SMC Hungary Ipari Automatizálási kft.
Budafoki ut 107-113 1117 Budapest
TEL: 01-371-1343 FAX: 01-371-1344
ROMANIA SMC Romania S.r.l.
Str. Frunzei, Nr. 29, Sector 2, Bucharest, Romania
TEL: 01-3205111 FAX: 01-3261489
SLOVAKIA SMC Priemyselná automatizáciá, s.r.o
Nova 3, SK-83103 Bratislava
TEL: 02-4445-6725 FAX: 02-4445-6028
SLOVENIA SMC Industrijska Avtomatilca d.o.o.
Grajski trg 15, SLO- 8360 Zuzemberk, Slovenia
TEL: 07388-5240 FAX: 07388-5249
SOUTH AFRICA (Distributor) Hyflo Southern Africa (Pty.) Ltd.
P.O.Box 240 Paardeneiland 7420 South Africa
TEL: 021-511-7021 FAX: 021-511-4456
EGYPT (Distributor) Saadani Trading & Ind. Services
15 Sebaai Street, Miami 21411 Alexandria, Egypt
TEL: 3-548-50-34 FAX: 3-548-50-34
SINGAPORE SMC Pneumatics (S.E.A.) Pte. Ltd.
89 Tuas Avenue 1, Jurong Singapore 639520
TEL: 6861-0888 FAX: 6861-1889
PHILIPPINES SHOKETSU SMC Corporation
Unit 201 Common Goal Tower, Madrigal Business Park,
Ayala Alabang Muntinlupa, Philippines
TEL: 02-8090565 FAX: 02-8090586
MALAYSIA SMC Pneumatics (S.E.A.) Sdn. Bhd.
Lot 36 Jalan Delima1/1, Subang Hi-Tech Industrial Park, Batu 3 40000 Shah Alam
Selangor, Malaysia
TEL: 03-56350590 FAX: 03-56350602
SOUTH KOREA SMC Pneumatics Korea Co., Ltd.
Woolim e-BIZ Center (Room 1008), 170-5, Guro-Dong, Guro-Gu,
Seoul, 152-050, South Korea
TEL: 02-3219-0700 FAX: 02-3219-0702
CHINA SMC (China) Co., Ltd.
7 Wan Yuan St. Beijing Economic & Technological Development Zone 100176, China
TEL: 010-67882111 FAX: 010-67881837
THAILAND SMC Thailand Ltd.
134/6 Moo 5, Tiwanon Road, Bangkadi, Amphur Muang, Patumthani 12000, Thailand
TEL: 02-963-7099 FAX: 02-501-2937
INDIA SMC Pneumatics (India) Pvt. Ltd.
D-107 to 112, Phase-2, Extension, Noida, Dist. Gautaim Budh Nagar,
U.P. 201 305, India
TEL: (0120)-4568730 FAX: 0120-4568933
INDONESIA (Distributor) P.T. Riyadi Putera Makmur
Jalan Hayam Wuruk Komplek Glodok Jaya No. 27-28 Jakarta 11180 Indonesia
TEL: 021-625 5548 FAX: 021-625 5888
PAKISTAN (Distributor) Jubilee Corporation
First Floor Mercantile Centre, Newton Road Near Boulton Market P.O. Box 6165
Karachi 74000 Pakistan
TEL: 021-243-9070/8449 FAX: 021-241-4589
ISRAEL (Distributor) Baccara Automation Control
Kvutzat Geva 18915 Israel
TEL: 04-653-5960 FAX: 04-653-1445
SAUDI ARABIA (Distributor) Assaggaff Trading Est.
P.O. Box 3385 Al-Amir Majed Street, Jeddah-21471, Saudi Arabia
TEL: 02-6761574 FAX: 02-6708173
15-18-21