lnstalling
/Connection
withthemains
1. DANGER TO LIFEI The electric connection must only be carried out by a qualifiedelectrician!
2. In order to clnnect the device to the mains, you have to install a power-plug.
3. The occupation of the connectioncables is as follows:
Cable
Pin
Brown
I iva
Blue
Neutral
Yellow/Green
Earth
lntemätional
N
4, The earth has to be connected!
5. Connect the device to the mains with the power-plug.
6. lf the device will be directly connec-tedwith the local power supply network, a disconnection switch with a minimum
opening of 3 mm at every pole has to be included in the permanent electrical insüallation.
7. In general, lighting effects should not be connectedto dimming-packs.
8. DANGER TO LIFEI Before taking into operation for the first time, the installationhas to be approved by an expertl
MSRPAR575
*'
INSTRUCTION
OPERATION:
After you connected the spot to the mains, but you can't control the sports via your lighting controller.
Lamps
Usethefollowinglamponlyin MSRPAR fixtures.
IMPORTANT
SAFEWINSTRUCTIONS
Lamp code
OSRAM GX9.5 MSR
Metal Halido Lamo
w
C- tomp
575
7,200"K
llfe hourg
1. Before you initiallystart-up, please make sure that there is no damage caused by hansportation.Should there be any,
consult your dealer and do not use the device.
2. CAUTIONI Be careful with your operations. With a dangerous voltage you cernsuffer a dangerous electric shock when
touching the wires! Keep away ftom heaters and other heating sources!
3. Do not mount the device on or near combustiblesufaces. Do not operate the device without a lens installed.
4. Always hang the device with the color frame retainingclip in the locked position.
5. This device falls under protection-class l, therefore it is essential that the yellow/green conductor gets connected to
earth. The electric connection must be carried out by a qualifiedemployee.
6. Make sure that the power-cord is never crimped or damaged by sharp edges. Check the device and the power-cord
from time to time.
8. lf the external flexible cable or cord of this luminaire is damaged, it shall be exclusivelyreplaced by the manufactureror
his service agent or a similar qualified person in order to avoid a hazard.
9. Shields, lenses or ultraviolet screens shall be changed if they have become visiblydamaged to such an extent that
their effectiveness is impaired, for example by cracks or deep scratcfies.
10. Never let the power-cord come into contact with other cables! Handle the power-cordand all connectionswith the
mains with particularcaution!
11. Always disconnect from the mains, when the device is not in use or before deaning it. Only handle the power-cordby
the plug. Never pull out the plug by tugging the power-cord.
12. During the initial start-up some smoke or smell may arise. This is a normal process and do'esnot necessarilymean
that the device is defective.
13. DANGER OF BURNINGI Never touch the device during the operation! The housing heats up to the housing
temperature T"**.
14. Don't switch the device on and off in short intervals as this would reduce the lamp's life.
'15.HEALTH
HAZARDI Never look directly into the light source, as sensitive persons may suffer an epilepticshock
(especially meant for epileptics)!
16. Keep away children and amateurs from the device!
17. There are no serviceable parts inside the device. Maintenance and service operationsare only to be canied out by
authorized dealers.
18. The symbol (z.ouf Oeterminesthe minimum distance ftom lightedobjects.The minimum distiancebetween
light-output and the illuminated surface must be more than 2 meter.
1000 hour
TECHNICALSPECIFICATIONS
Power supplv:
Power consumption
Dimensions(LxWxH)
wetqht
Fittinq lamp
FuSe
Maximum ambient temoeraturet
MaxlmUm hOuslngtefip€Iätuf€ ts:
Mrnrmumorslance:
230-240VAC.50Hz
600w
zcu xzcu x ccumm
rz.J Kq
MSR Metal Halide Lamp Base: GX9.5
250V.6.34
25"C
140'C
ZM
THE END
X
I
,4.
Accessories
Color frame
Very Narrow Spot lens
Narrow Spot lens
Medium Flood lens
407CF
4OO-VNSP
4OO-NSP
4OO-MFL
Wide Flood lens
Set of four MSR PAR lenses
(VNSP,NSP,MFL,WFL)
.'1 .
4OO-WFL
4001S4
[:Tl'ffi*]il".
frame
retaining
Color
clip
,b^
The color frame holder is equipped with a spring-loaded retainingclip that prevents color
frames and accessories ftom falling out.
ftEl
WARNINGI Hang the MSRPAR with the color frame retaining clip in the locked position.
Change lenses if they become cracked or badly scratcted. Cautionl Never opente the MSRPARwithout a lens in place.
\\
tttl
l.Release the retaining clip by pushing it sideways.The retainingclip opens.
2.lnsert the color fame.
3.Press the retaining clip down until it locks.
Älofe; Use only color frames or top hats with 6.7-inch inside diameter.
\
Installing
a lens
\\l-a
\q
fdiltt
LUL-
MSRPARlenses
Changing
I
tltrtrtz
as=,r
Figure 1
Cleaning
thereflectol
l.Position the fixture with the front of the unit (the lens side) facing you, and tilted slightly (Hgurc1).
2.Position the lens rotation ring with the spring clip at the top of the fixture,direcüybelow the
retaining clip.
3.Hofd the lens by the edge, and position it so the convex side faces the back of the fixture (Figure 3).
Note: /nsfa//rng the lens with the convex side out will not impah the optics,but it will make
removing the lens diftcuft.
The following recommendations are offered when cleaning and inspec{ing lenses and reflectors:
Do not use glass and window cleaners on the reflector. Chemicals in these cleaners will harm the reflective coating.
Do not use paper towels or harsh materials to wipe the reflector. These materials can scratch the surface of the reflec'tor.
WARNaNGI
Unptug the nxturc
l.Remove the fens so you can access the reflector fom the front of the fixture. See Removing a lens on page 2
2.Remove dust with a blast of oil fiee air, or wipe with a clean, soft, lint-fee cotton cloth. lf this is sufficient to remove
dust, go to step 5. Othenrrise, continue to step 3.
3.Dampen a clean, sofi, lint-free cotton cloth with a mild, soapy water solution and gently wipe the reflector.
4.Remove any soapy water residue with a clean, soft, lint-fiee cofton cloth dampened with water.
5.Reinstall a lens before using the fixture.
Installing
thelamp
.
Alwaysreplacethe lampif it becomesdamagedor deformed.
Verifythatthe lampyou use is suitablefor the electronicpowerat yourfacility.
Cautlon! Operatinglampsaboveor belowtheir rated voltagereduces
lamp life and can causeprematurelamp failure.
'l .Disconnect
the unitfrom powerbeforeinstallingthe lamp.
WARNINGI Let tamp cootbefore c
2.Loosenthe knurledbolton the backof the lamphousingand pullthe housing
straightout from the backof the fixture.
3.Removethe lampfrom its box, holdlng it by the base.
Note: Io avoid premature lamp failure, do not touch the lamp glass with your
fingers. lf you touch the lamp during installation,clean it carefullywith
rubbing alcohol and a clean, lint-[reecloth before operation.
4.Lineup the flat sidesof the lampbasewith the bracketson eithersideof the
Lamphousing
socket(Frgure2).
S.Pushdownon the lampbaseuntilthe lampis firmlyseated.Makesurethatthe
Figure 2
lampis fullyseated,withthe bottomof the lampheatsinkflushto the lamphousingcasting.
Cautlonl lmproperlyinstalledlampscauseprematurelamp failureand socketproblems.
6.To reinstallthe lamphousing,centerit on the reflectorand the bglt hole,thentightenthe knurledboltto securethe
lamphousingin place.
Lenses for the MSR PAR come in four versions. The type or beam spread can be identified by the lens texture.
VNSP
NSP
,trMTIIN.
III
,/'.l]rll1llllN
tL
,ffi.
h.
/M
tu
mm|IIIII|IIIIIIIN tfit}\
AN
//
VV
\\
il\
)ill
Verynanowspot
Clearglass
15'Roundbeamshape
The fixture should be installed outside areas where persons may walk by or be seated.
1. Before rigging make sure that the installationarea can hold a minimum point load of 10 times the fixture'sweight.
2. Do not install the fixture on radiant-heating type area
3. Out of the way but within arm's reach, so you cttn operate it easily
4. Close enough to an AC outlet to use the attached power cord
5. When installing the device, make sure there is no highly inflammable material(decorationarticles,etc.) within a distance
of min. 1.0M
6. For overhead use, always install a safety-rope that can hold at least 10 times the weight of the fixture.You must only
use safety-ropes with screw-on carabines.
Warnlng: To reduce the likelihood of the injury or damage to person, mount it only on a stable and sturdy area.
fl"""'
Installation
WithHook
Lens
identification
(
a Mounting
Location
Selecting
ffi)
lä
W
Narowspot
glass(slightdiffuse
Stipple
texture)
19'Roundbeamshape
,2.
WW
Feuerfacets,sized
6x22mm
21'x34'Oblong
beamshape
ffilffi
\m
\@
\:W
tm
tM
tw
illl',1#,,,,0*u,',,,
30'x51'Oblong
beamshape
Salty Rop€
You can choose four appropriatehook from your dealer to fix the fixture
Camblm
Salty
to the mounting pipe(e.g.trusssystem), and adjust the positionof the
fixture once it is mounted. (Figure 6)
1. Tightly fasten the hook to the yoke with the providedyoke bolt and
lock washer.
2. Place the hook on the mounting pipe, then tighten the pipe bolt to secure it.
3. Adjust the desired inclination-anglevia the yoke and fix the Yokelocking
knob.
4. Pull the safety-ropethrough the hole on the housing and over the mounting
pipe etc. Insert the end in the carabine and tighten the safety screw.
.3.
Figure 6