ROBOT LINE TRACKING
MOUSE KIT
C-9801
TOOLS you'll need
Alimentation
4 batteries 1,5 V AA (not included)
The mouse is a line follower robot that follows a black line (or any other color) on a white background picture using switches like eyes.
You can create the route to follow to your liking. Trace the path of the robot is as easy as pasting in a clear ground, black tape
(electrical tape), marking the desired route
LIST OF ELECTRONIC COMPONENTS
Resistor ¼ W
220
(Red Red Brown Gold) 4 pcs.
330
(Orange Orange Brown Gold) 3 pcs.
3,3 K
(Orange Orange Red Gold) 1 pc.
10 K
(Green Blue orange Gold) 1pcs,
56 K
(Green bluo Orange Gold) 1pc.
IN4004
1pc.
22p Ceramic capacitor 1 pc
104 Ceramic capacitor 2 pcs.
100 K (Brown Black Yellow Gold) 1 pc
3,3M
(Orange Orange Green Gold) 1 pc
560
(Green Blue Brown Gold) 1 pc
Resistor 1/8 W
220
(Red Red Brown Gold) 3 pcs.
33 k
(Orange Orange Orange Gold) 3 pcs.
EM78P156
EP 1pc
LED diat. 3 mm.
Red
3 pcs.
Green 2 pcs.
Transistor
1815 o C945 3 pcs.
8050 2 pcs.
Slide switch 1 pc.
Photo Switch LTH1550-1 3 pcs.
Electrolytic
capacitor 100
uF 1 pc.
C.I. Plate detector 1 pc.
C.I. Plate principal 1 pc.
Microphone diat. 10
mm. 1 pc.
Cable connector:
Yellow 1 pc.
Blue 1 pc.
Orange 1pc.
Green 1 pc
Red 1 pc.
Black 1 pc.
Battery Holder : 1 pc
Spins Connector 180X 1 pc
www.cebekit.com
Pin de Diat. 1,3
mm. 8 pcs.
Spins Connector 90X 1 pc
-
info@cebekit.com
Connection 1 pc.
C-9801
List of mechanical components
Body Mouse
Wood Badge
P1 – Gearbox 2pc.
P2 – Engine 6V DC
2 pcs.
P4 - Metal rod diat.
3x52 mm 2 pcs
P3 - Metal rod diat.
2X40 mm 2 pcs
P5 – Pinion 10d
white 2 pcs.
P6 - Front Gear
36d/14d white 2 pcs.
P10 - Nylon bearing
5,6x4,8x1,95 4 pcs.
P7 – gear 36d/0d
white 2 pcs.
P13 Support
U 1 pc.
P8 – gear 36d/0d
White 2 pcs.
P14 Squad
4 pcs.
P9– gear 36d/14d
Red 2 pcs.
P15- Hex
Spacer 2 pcs.
P11 - Rear wheel diat.
32X3,5 mm. 2pcs
P16 Plastic
Clip 3 pcs.
Nylon separator
diat. 3X2 mm.
2 pcs.
P20 autorosca screws
2x4 mm. 14 pcs.
PRINTED CIRCUIT ASSEMBLY
P12 - Rubber gasket diat.
30X3 mm. 2pcs.
P18 – screws M
2x10 mm.4 pcs.
P21 autorosca screws
2x6 mm. 4 pcs.
P19 – screws M
3x5 mm. 4 pcs.
P22– nut M2
4 pcs.
The numbering of the pieces (ID) are silkscreened on the PCB
Step 1. We suggest starting with the resistance of 1 / 4 W
D
R5/6/11/12
R7/8/9
R10
R2
R4
R13
R3
R1
Description
220
330
3,3 K
10 K
56 K
100 K
3,3 M
560
Color Code
Red Red Brown Gold
Orange Orange Brown Gold
Orange Orange Red Gold
Brown Black Orange Gold
Green Blue Orange Gold
Brown Black Yellow Gold
Orange Orange Green Gold
Green Blue Brown Gold
Units
4
3
1
1
1
1
1
1
Note that the meaning of 5-pin connector
must be the same as that drawn
2
www.cebekit.com
-
info@cebekit.com
C-9801
The numbering of the pieces (ID) are silkscreened on the PCB
Step 1. Mount the resistors 1 / 8 W and photo switch
ID
R 17/18/19
R 14/15/16
U 5/6/7
Volue
1/8 W 33 K
1/8 W 220
LTH-1550-1
Colors
Orange Orange Orange Gold
Red Red Borwn Gold
Units
3
3
3
Step 2. 5 Insert the connector pins 90X on the side of the copper plate bearing
(opposite of the other components). This drawing will help you do it correctly
Step 2. Assemble the following components
ID
UI
MIC
C 1-2
C3
Ec 1
Q 1/2/3
Q 4/5
D 2/3/4
D 5/6
IR
l/r (+ - )
BAT (+ -)
SW
D1
Description
Chip
Microphone
Capacitor 104P
Capacitor 22p
Electrolitic Capacitor 100uF
Transistor 1815
Transistor 8050
Led Red
Led Green
Connection 180X
Pin 1,3 mm.
Pin 1,3 mm.
Pin 1,3 mm.
1N-4004
Units
1
1
2
1
1
3
2
3
2
1
2
2
4
1
Gearbox left side
MECHANICAL ASSEMBLY
Gear Housing Assembly
Gearbox left side,
and mounted
Gearbox right side,
and mounted
Positive Terminal
The overhang should be toward
the metal case
Orange wire
Yellow wire
www.cebekit.com
-
info@cebekit.com
3
C-9801
Red
Black
Reassembling the battery
4
www.cebekit.com
-
info@cebekit.com
C-9801
Mounting gearboxes
Orange
Blue
Green
Connection G
Yellow
Red
Black
Connection H
Connection I
Mounting the main circuit
www.cebekit.com
-
info@cebekit.com
5
C-9801
Connection
A
B
C
D
E
F
G
H
L (+)
L (-)
R (+)
R (-)
BAT(+)
BAT(-)
Red
Black
Red
Black
Blue
Orange Yellow Green
6 V Batteries
Housing Assembly
Before mounting the body of the mouse at the bottom make sure the
wiring is correct and continue with this unit operation, to see if operating
conectly
If everything is correct, screw the body of the mouse to the base
NOTE
1 - Do not forget the bubble
transparent mouse body can not
exceed the wooden plaque (see
picture left).
2 - Before screwing the mousetransparent body to the wooden
plate, check that the bubble of the
body does not touch the wheels
and allows the mouse to move
slowly
6
www.cebekit.com
-
info@cebekit.com
SW
I
(+ -)
5 Pins connection
C-9801
Operation
1 - Use black electrical tape to create a path with twists and turns for your robot.
2 - Place the switch ON
3 - Place the mouse on the path you created. The black line should be in the detection zone of the 3 photo switches.
4 - Hit the body of the mouse to start the ball rolling robot mouse
You can design any type of journey
1 example
3 example
2 example
Possible Problems
1 - Check that you have placed the batteries with correct polarity
2 - Check that the polarity of the microphone, integrated circuit and the
capacitor is correct.
3 - Check that the wiring is the same as indicated in (mechanical assembly)
4 - E noise coming from the gearbox can interfere with the signal received by
the microphone, putting grease between P6 front gear and the rod of 2
mm. P3, reduced noise.
5 - NOTE. DO NOT place any lubricant between the rod of 3 mm. P4 and P7
and P8 gear.
6 - If the mouse is going backwards, see if the two motors are connected in
reverse
Wiring diagram
finished product
NOTE. This kit is recommended for children aged 14 years, always escorted by an adult
www.cebekit.com
-
info@cebekit.com
7