ENVIRONMENT, OHS, CHEMICAL & LABORATORY
Environmental Gas & Vapour Meters
Personal Gas & Vapour Monitors
Airborne Dust & Particle Meters
Air Quality & Heat Stress
Moisture & Humidity Meters
Noise & Sound Analysers
Radiation Monitoring & Protection
Floor Slip Testers
Water Quality, pH Meters & Eletrochem
Light Meters, UVA/B/C Measurement
Weather Stations
Environment Flow Meters
Laboratory & Hand-held Microscopes
Balances & Scales below 8kg
Chemical & Analytical - General
Laboratory Instruments, Spectroscopy
Environmental Gas & Vapour Meters
cont’d.
GasCheck 3000 Portable General-Purpose Leak Detector
ION,GASCHECK3000 (5906)
Ion Science Gascheck Helium, Butane
& SF6 Detector
ION,GASCHECKG3 (5907)
ISC MDU420 Logging Methane Monitor
ISC,MDU420 (5956)
AU
Dual-range methane monitor with non-dispersive infrared sensor. Low range
0 to 100% LEL, and auto-range 0 to 100% methane by volume. Internal pump
for ambient air or stream sampling. Data logging included, with software and
cable for download. Supplied with 450mm stainless steel probe for flue gas
analysis. Rechargeable, with alkaline-battery pack as backup.
Oldham MX21 Plus Gas Monitor for Sulphur Dioxide SO2
OLD,MX21-SO2 (5936)
AU
Portable gas detector for personal, workplace or space monitoring of sulphur
dioxide (SO2) in the range 0 to 30ppm. Operation in passive or pumped modes,
with sampling tube and flexible probe. Data logging, with software included for
download to serial printer or computer. Rolling storage of up to 48h data (at
1min intervals) in multiple groups. Rechargeable battery.
Aeroqual 500L Portable Logging Ozone Monitor
AU
Portable ozone monitor fitted with low concentrationrange detection head. Operating range 0 to 0.5ppm
ozone with display in ppm or mg/m3. Gas sensitive
semiconductor [GSS] sensor for accurate low-level
measurements, T90 response approximately 100s.
Operation from mains power supply or battery pack
(4h operation). Internal data logging for 8,000 points
with software and cable for download to PC, or data
logging direct to PC. Application for indoor air quality
measurements.
Photovac 2020 Portable PID VOC Monitor
PHO,2020PRO (5950)
AU
Portable handheld VOC (Volatile Organic Compound) monitor with data
logging. PID sensor (Photo-Ionisation Detector) fitted with 10.6eV lamp.
Ranges 0.5~2000ppm humidity compensated. Downloadable data logging for
15,000 points with time, data and header. Intrinsically safe.
PPM 400 Portable Formaldehyde Meter
PPM,FORM400 (5962)
Odalog ODA6000CP NO2 & CO Area Monitor for Vehicle-parks & IAQ
AU
Portable Formaldehyde meter for measuring
airborne formaldehyde in the workplace.
Electrochemical sensor, with internal pump
for rapid response. Operating range 0.05 to
10ppm with readout on 4 digit LCD display.
Kit includes field calibration standard.
Operates from 9V alkaline battery.
AU
Portable multi-gas monitor for area air-quality measurement, logging or
personal monitoring in car-parks, loading areas and related zones. Configured
for carbon monoxide (from petrol vehicles) and nitrogen dioxide (from diesel
vehicles). Ranges CO 0 to 500ppm (to 1ppm) and NO2 0 to 50ppm (to 0.1ppm).
Dust and water sealed to IP66, and rated intrinsically safe for general or mines
use. Logging memory 500K readings. Integral infrared communications
interface, with software and IrDA USB adaptor for configuration and download.
Rechargeable, approximately 7 days operation on full charge.
RAE Systems Minirae 2000 Portable PID
RAE,MR2000 (5950)
AU
Portable handheld VOC (Volatile Organic
Compound) monitor with data logging. 3-D PID sensor (PhotoIonisation Detector) fitted with 10.6eV lamp. Ranges 0 to
999ppm (resolution 0.1) or 100 to 10,000ppm (resolution 1)
VOC expressed as isobutylene. Built-in correction factors for
102 compounds from a total standard library of 250. Integrated
pump for local or remote (30m) sampling, with stall protection
against liquid ingress. Downloadable data logging for 1,500
points with time, data and header. Intrinsically safe. Up to 10h
operation with rechargeable (NiMH) or alkaline batteries.
Haloteck 78000 Refrigerant Gas Leak Detector
HAL,78000 (5804)
AU
Microthermal conductivity gas detector. Reading in
cc/s, g/yr, mg/m3 or ppm. Detects most gases however
particularly suited to ammonia, argon, butane, helium,
hydrogen & SF6. Calibrated against Helium. Battery
Life 40h. Sensitivity (cc/s) He 1x10-5, CH4 5x10-5,
R12 5x10-5, Ar 1x10-4. Accuracy 5% of displayed
reading + 1 digit. Response 1s. Flow rate 2cc/min. Operating -20 to 60°C.
Data logging, stores 10 readings.
See also Combustion, Flue & Industrial Gas Analysers on page 57
APT,ODA6000CP (5972)
AU
Micro thermal-conductivity sensor for high-sensitivity detection of gases with
a thermal conductivity different to that of air, including helium, carbon dioxide,
refrigerants, sulphur hexafluoride, natural gas, etc in 5 groups. Direct reading
of leak rate in ml/sec with audio and visible signals. Detection limit for helium
2E-5ml/s. Battery Powered.
Environmental Gas & Vapour Meters
AER,500L (5958)
www.techrentals.com.au
AU
For use by refrigeration engineers. Rapid response 0.2s, audio output,
zero warm up time. Single control, battery operated, sensor tip insensitive
to draughts. Sensitivity better than 3g/y R12, 25g/y R134A. Responds to
halogenated hydrocarbons and many fire extinguishant gases, [also sulphur
hexafluoride SF6]. Battery life 30h. Duty cycle continuous. Probe length
240mm. Weight 280g.
70
ENVIRONMENT, OHS, CHEMICAL & LABORATORY
www.techrentals.com.au
Environmental Gas & Vapour Meters
cont’d.
Airborne Dust & Particle Meters
cont’d.
TSI 8520 DustTrak Airborne Particle Monitor
Minirae 3000 Advance Handheld VOC Monitor
RAE,MR3000
TSI,8520 (5872)
MY
AU
Portable aerosol monitor. Laser photometer with 90ºC scattering
detection, Range: 0.001 to 100mg/m3 [Calibrated for A1 test dust, ISO
121203-1], resolution: 1% of reading or 0.001mg/m3; particle size range: 0.1
to 10μm. Internal pump flow rate 1.4 to 2.4l/min (1.7 nominal). Data logging
30,000 data points (21d@1min), log interval: 1s to 1h. RS232C interface
and software included. Battery operated.
Handheld volatile organic compound (VOC) detector.
Photoionization Detector’s (PID) extended range of 0 to
15,000 ppm, ideal For applications from industrial hygiene,
to leak and HazMat detection. RF modem allows real-time
data transmissions with a base controller located up to 500
feet (or two-miles with optional RAELink3 portable modem)
away from the MiniRAE 3000 detector. A personal computer
can be used as the base station for a Mini-RAE 3000 system.
TSI 8520-1 Environmental Enclosure for DustTrak
TSI,8520-1 (5874)
Personal Gas & Vapour Monitors
BW Bump & logging download for
BW,MICROCLIP
TSI 8525 P-Trak Ultrafine Particle Counter
BW,BUMP (5938)
TSI,8525 (5876)
AU
TSI 8530 Aerosol Monitor and
Logger
BW Gas Alert Micro Clip Confined Space 4 Gas
Detector
TSI,8530 (5873)
AU
TSI Environmental Enclosure for the TSI,8530
TSI,8530-ENC (5875)
BW Sampling Pump for BW,MICROCLIP
AU
TSI 8533 Aerosol Monitor and Logger
TSI,8533 (5870)
Lion SD-400P Breath Alcohol Analyser
AU
SKC Universal Air Sample Pump
AU
TSI AM510 Personal Aerosol Monitor;
CSA & ATEX IS approvals
For OH&S air sampling. Provides air flow rates from 5
to 500ml/min. Unit has hold function to allow for breaks.
Uses quantity 6xC 2.4AHr NiCd batteries.
TSI,AM510 (5871)
AU
Wearable dust monitor. Built in Impator allows
you to chose either ‘none’, 1, 2.5 or 10μm particle
sizes. Datalogs TWA in the range of particle
concentrations from .001 to 20mg/m3 Runs 9.2hrs
on rechargeable NiMH batteries. USB download
capability. CSA & ATEX IS approvals.
Airborne Dust & Particle Meters
Abacus 301 Hand-held Airborne Particle Counter
ABA,301 (5878)
AU
Portable dust and particle monitor, light scatter photometer.
Measure concentrations corresponding to PM1, PM2.5 & PM10. Aerosol
concentrations 0.001 to 150mg/m3. Used for industrial/occupational
surveys, indoor air quality monitoring, outdoor environmental monitoring,
baseline trending and screening,etc. Will size particles in three sizes PM1,
PM2.5 & respirable PM10 and Total.
Portable breath alcohol analyser with attached printer. Uses
disposable mouthpieces. Approved by most law-enforcement
agencies.
SKC,224-PCXR4 (5940)
AU/MY
Enclosure to suit the TSI,8530. Includes two additional
batteries and charger. Includes waterproof enclosure
and heat shield and enclosure stand.
Motorised sampling pump that provides 300ml/min for remote sampling up to
18m away. Runs continuously for 30hrs on batteries. Includes 3m sampling
hose. Includes built in water traps and particulate filter.
LIO,SD-400P (5966)
AU/MY
Portable dust and particle monitor, light
scatter photometer. Measure concentrations
corresponding to PM1, PM2.5 & PM10. Aerosol
concentrations 0.001 to 150mg/m3. Used for
industrial/occupational hygiene surveys, indoor
air quality monitoring, outdoor environmental
monitoring, baseline trending and screening, etc.
Continuous LCD shows real time gas concentrations.
Simple 1 button operation. Measures:- H2S 0 to 100ppm
(1ppm resolution), CO 0 to 500ppm (1ppm resolution),
O2 0 to 30% (0.1% resolution) and Combustible gases
0 to 100% LEL (1% resolution), 0 to 5% v/v (0.1% resolution). Alarms:- visual,
vibrating and audible (95dB), Low, High, STEL, TWA and OL (over limit).
Lithium polymer battery life 12h (typical) recharge time <3h.
BW,GA-SPAK (5939)
AU
Range 0.01 to 5 x 105 particles/cm3. Particle size range 0.02 to greater than
1micron. Includes PC software and cable. Suitable for detection of ultrafine
particles associated with pollutants. Battery powered (8h operation using
alkaline batteries).
Automatic calibration testing and data management
system for the BW microclip gas detection equipment.
Carries out fully automatic “hands-free” calibration and
functional bump test. It also enables data collected
during operation of the BW microclip to be downloaded.
BW,MICROCLIP (5937)
AU
Weatherproof outdoor housing for TSI,8520 aerosol monitor. Rugged case
with tripod mount, fitted with sample inlet and water trap. Includes extendedlife battery pack and charger/adaptor.
AU
Portable particle measuring system typically used in clean room applications.
Four fixed size channels 0.3, 0.5, 1.0 & 5.0 micron. Count data automatically
stored in a 500 sample memory which can be downloaded to a PC.
Selectable sample time. Includes zero count filter for checking backgrounds.
When used with included software will check clean rooms to ISO 14644 and
BS5295 requirements. Battery operated.
Save your time and reduce your real costs.
Find out all about our Configuration and Download
solutions on page 11.
71
ENVIRONMENT, OHS, CHEMICAL & LABORATORY
Air Quality & Heat Stress
www.techrentals.com.au
Moisture & Humidity Meters
Casella Microtherm WBGT Area Heat Stress
Monitor
CAS,MICROTHERM (5868)
GE Panametrics PM880 Industrial
Moisture Analyser
AU
PAN,PM880 (6119)
Portable area heat stress WBGT monitor with
real-time graphical display. Measures heat stress
potential [WBGT index] according to ISO7243.
PRTD sensors with internal calibration-reference
for wet-bulb, dry-bulb and globe temperatures.
Large LCD display for numerical or graphical indication of temperatures and
processed values for WBGT [indoor/outdoor plus TWA], relative humidity and
dewpoint. Simple keypad/menu setup. Data logging for up to 32 separate
runs and 49,100 records, with interval 30s to 1h. RS232C port with included
PC software for download and reporting or realtime display. Low water-level
warning, and settable audible/visible WBGT alarm. Handheld, free-standing
or tripod-mount. Battery operated.
AU
Intrinsically safe moisture analyser for
compressed air systems, non-corrosive gases &
hydrocarbons such as natural gas (IS certification
to ATEX and CSA). Displays dew point, moisture
concentration, pressure & temperature. Dew point
calibrated measurement range -80 to 20°C with
data to -110°C. Pressure range 7 to 69bar limited
by sensor, gauge and safety-valve (operating range from 5μHg). Temperature
range -30 to 70°C. Gas flow operating range from static to 10,000cm/s velocity.
Supplied with compact sample system with gauge, safety-valve, sampling
valves and fittings (¼” Swagelok). Data logging of up to 100K moisture points,
with infrared port and software for download. Battery powered only (15-24h
operation) with second battery and charger (note charger is not IS).
Testo 635-2 Humidity, Temperature & Dewpoint Meter
TES,635-2 (5859)
AU
Portable humidity meter fitted with robust stainless probe
with sintered filter-cap for general or duct measurements to
120ºC, and fast-action K-type surface temperature probe.
Displays relative humidity, absolute humidity, dew point,
degree of humidity, enthalpy, temperature, and differential
temperature (dewpoint to surface). Operating range 2 to
98%RH (±2%). Air temperature -20 to 120ºC (±0.2/0.5).
Surface temperature -60 to 300ºC (±0.1). Internal memory
for 10,000 values with USB interface, cable and software
for download and presentation. Battery operated.
Noise & Sound Analysers
See also Vibration Analysis on page 62
ARL EL-315 Environmental Noise Logger
ARL,EL-315 (5694)
Testo 645 Humidity & Dewpoint Meter
TES,645-1 (5858)
AU
Portable humidity meter fitted with robust stainless
probe for ambient work or duct measurements
to 120°C. Displays relative humidity, absolute
humidity, dew point, degree of humidity, enthalpy
and temperature. Operating range 2 to 98%RH
[±2%], -20 to 120°C [±0.4/0.5]. Battery operated.
ARL EL-316 Environmental Noise
Logger Type 1
ARL,EL-316 (5695)
AU
Measures CO2 0 to 5,000ppm ±3%, temperature
0 to 60ºC ±0.6ºC, humidity 0 to 95% ±3%, CO 0 to
500ppm ±3% and barometric pressure 517.15 to
930.87mmHg ±2%. Calculates dew point, wet bulb
and percent outside air. Displays 5 measurements
simultaneously. User selectable logging interval and
start stop times. Stores 39 days data at 1min intervals
56,035 data points. This unit also has external
thermocouple measurements.
ARL NGARA Environmental Noise Logger
ARL,NGARA (5690)
AU
Can be configured to record all sound continuously
so noise data can be post processed. It can prove
logged data, WAV data & alarm/triggered details.
Type 1 microphone provided.
TSI Q-Trak plus Indoor Air Quality Monitor with
Logging
TSI,8554 (5860)
AU
Environmental noise logger with display for fieldreading of summary results. Portable, self-contained
and weatherproof. Type 1 performance, continuous
90dB dynamic range, fast response, frequency
weightings A and C. Monitors environmental noise
continuously for up to 3 weeks, calculates and stores
over 7,500 sets of Ln indices. PC required to set up
system and download data using software supplied.
Set up also possible from front-panel.
TSI Q-TRAK IAQ Monitor CO2,
CO Temperature & Humidity Logger
TSI,7565 (5861)
AU/MY
Portable, self-contained and weatherproof with display
for field reading of summary results. Continuous
90dB dynamic range, frequency weightings A and C.
Monitors environmental noise continuously for up to
3 weeks, calculates and stores over 7,500 sets of Ln
indices. PC required to set up system and download
data using software supplied. Set up also possible
from front-panel.
AU
B&K 2237A Type 2 Integrating Sound Level Meter
Indoor air quality (IAQ) monitor for temperature and
humidity measurements, CO and CO2 concentrations.
Humidity range 0 to 95%, temperature range 0 to
50°C. Electrochemical cell for CO 0 to 500ppm.
NDIR cell for CO2 0 to 5,000ppm. Data logging for
48,671 data points with interval adjustable 1s to 1h.
Fitted with RS232 interface, and software included
for download, storage and reporting. Battery or
mains operation with AC adaptor.
BK,2237A (5661)
AU
Measures RMS and peak simultaneously. Linearly weighted
analogue output for sound recording, 0 to 0.5VAC (RMS). Measurement
range 30 to 140dB. Time weightings fast, slow & impulse. Independent
frequency weightings A [for RMS readings SPL, MaxL, MinL, Leq, Inst] and
C [for peak readings Peak and MaxP]. Real time clock for time and date
stamp. Records 40 measurements for download to PC. Calibrator included.
Battery operated.
72
www.techrentals.com.au
ENVIRONMENT, OHS, CHEMICAL & LABORATORY
Noise & Sound Analysers cont’d.
Noise & Sound Analysers cont’d.
B&K 2238E Type 1 Integrating SLM Enhanced Software &
Logging
BK,2238E-NATA (5678)
Digital Audio Test Set
comprising of NTI Digirator &
NTI Digilyser
AU
Type 1 (class 1) Integrating sound level meter with additional functions
including enhanced software, frequency analysis and data logging.
Standard routines include functions for workplace measurements
and general sound-level checks; enhanced software (firmware) offers
additional measurements and statistics for assessment of environmental
noise problems; frequency analysis automates measurements in the
9 single octave bands and 29 1/3 octave bands. Supplied with field
calibrator. Compatible with BK,7815 Noise Explorer Environmental
software for download, data analysis and display.
NTI,NT-DAS (5684)
AU
Audio Excel Line for digital audio signals. System
including the Digilyzer and Digirator for producing
digital audio signals and analysing those digital
audio signals up to and including 5.1 surround
sound. Up to 192kHz 24bit, AES3,S/PDIF, TOSLINK & ADAT. ync input
(AES3, Word Clock, Video). Supports Dolby Digial, E, PL II, DTS. Channel
transparency check. Channel delay measurement
Quest 2400 Type 2 Sound Level Meter
QUE,2400 (5660)
B&K Noise Monitoring Terminal
with model 2238F SLM
BK,2238NMT-KIT (5696)
AU
Noise logging system with B&K model 2238F Class 1
Sound Level Meter equipped with internal software for
Basic SLM and Logging. Portable, wheeled weatherproof
case. Standard SLM operation for fast, slow and impulse
time weightings and A, C or linear frequency weightings
RMS. Linear or C frequency weightings for peak
detection. Internal memory 2MB total for logging up to 12
parameters including auxiliary signals. Fitted with serial
RS232 interface, and provided with BKlink software for
download of logged data to PC. Supplied with field calibrator, charger and
12V, 18Ah battery, for operation for up to 14 days logging at 15min intervals.
Rion NL-04 Sound Level Meter
RIO,NL-04
AU
Type 1 (class 1) integrating sound level meter with backlit LCD
display, NATA certification. Simultaneous RMS (A,C) & peak (C) detection
with independent frequency weightings. Measuring range 30 to 140dB.
Time weightings fast, slow and impulse. Parameters Leq, MaxP, MaxL,
MinL, Peak, SPL and Inst. Memory for 40 data records with realtime clock.
Serial port for data download. Calibrator included. Operates with 4 x AA
alkaline batteries.
Rion NL-05 Type 2 Sound Level Meter
RIO,NL-05 (5664)
AU
Software package for downloading and reporting of noise data measured
with B&K meters. Compatible with sound level meters (2239, 2238) and
noise dosemeters (4443). Offers data transfer, formatting of data for
export, display and print in tabular or graphical form, file management
and calculation of sound power or sound reduction index from intensity
measurements.
Rion NL-32 SLM with RTA & NATA Certification
RIO,NL-32RTA-NATA (5674)
RIO,NL-32RTA
AU
MY
Precision integrating sound level meter to IEC type 1
(class 1) specification, with NATA calibration. Fitted with
internal Compact Flash Card reader and supplied with
NC-74 field calibrator. Frequency range 20 to 20,000Hz
with weightings A, C, and flat. Time weightings fast,
slow and impulse. Measurement range (A) 28 to 138dB.
Broadband measurement functions Lp (SPL), Leq, Lmax/
min, Lae, Lx, and selectable auxiliary functions with manual or auto storage
[logging]. Measurement time (Leq) from 10s to 200h. Inbuilt memory for up to
100 data sets, or to limit of fitted CF card using manual or auto storage. AC
or DC outputs, RS232C interface and cable CC-93 for serial printer. Supplied
with NX-22RT card for real time 1/1 and 1/3 octave analysis and display, for
measurement functions Lp, Leq, LE, Lmax and display of AP (all-pass) AP(A)
and 1/1 or 1/3 octave values as selected, with manual data storage only to NX22RT card. Download of card-data to PC requires flashcard reader. Alkaline
batteries (24h operation) or AC adaptor.
Ivie IE-35 Type 1 Audio Analysis Systems
IVI,IE35-2P (5682)
AU
Sound level meter to IEC 651/1979 & IEC 804/1985 type 2 requirements.
Measures Lp, Lmax, Leq, Lae. Response types A, C, and flat. Fast and slow
time weightings. Complete with calibrator. Internal memory and print-out
for Leq data (printer CP-10 optional, also prints other parameters), RS232C
interface. Recorder outputs 1VAC RMS & 3.5VDC. Operates from batteries
or AC adaptor.
B&K 7815 Environmental Software - Noise Explorer
BK,7815 (5688)
MY
Meets IEC type 2. Five measurement functions: Lp(SPL), Leq, LAE, Lmax
& Lx(L5,L10,L50,L90,L95). 6 automatic measurements & data store. Built-in
RS232C interface for computer communication. 70dB dynamic range (digital
display), 27 to 130dB (A) measuring range. Wide range of time settings for
Leq, LAE, Lmax & Lx; 10s, 1, 5, 10, 15, 30min, 1, 8, 24h & manual time
setting (up to 99h 59min 59s). RMS: fast, slow,10ms. 4 digit LCD display,
0.1dB resolution, updated every second, plus 60dB analogue display display
1dB resolution showing the instantaneous value. Memory battery back-up.
AC & DC signal o/p for level expanding system by optional filters, memory
card & others.
B&K 2239A Type 1 Sound Level Meter NATA Certification
BK,2239A-NATA (5667)
AU
Type 2 sound level meter with LCD display for sound pressure level [SPL]
or maximum level [MAX]. Frequency weightings A and C, time weightings
Fast and Slow. Ranges 30 to 140dBA and 40 to 140dBC with overload
indication. AC and DC outputs. Battery powered.
AU
Audio Analyser with Dell Axim X51v PDA. Fitted with
half-inch free-field Type 1 microphone and pre-amplifier.
Functions include SPL (sound level), Real-time analysis,
“seat-to-seat” variation for audio setup, reverberation
measurement, “strip-chart” recording on display, voltage
and oscilloscope displays and signal generation. Supplied
with field-calibrator, microphone extension cable, spare
battery and software for data-download to PC. SPL
facilities include time and frequency weightings - fast,
slow, peak or impulse and A, C or Flat. FFT based Real
Time Analysis includes 1/1, 1/3, or 1/6 octave bands with
a maximum resolution of about 1/24 octave. Additional
functions include spectrum subtraction, averaging, Noise
Critera or Reduction contours and reverberation-decay to ISO-20 and ISO30. Signal-generation includes sine, square, triangle and white or pink noise.
Save your time and reduce your real costs.
Find out all about our Configuration and Download
solutions on page 11.
73
ENVIRONMENT, OHS, CHEMICAL & LABORATORY
Radiation Monitoring & Protection
Water Quality, pH Meters
& Electrochem cont’d.
See also E & H Field Strength Meters on page 13
Horiba U-52 Multi-function Water Quality Meter
Fluke 481 Radiation Survey Meter
HOR,U-52-10M (6025)
FLU,481 (5580)
HPI Cypher 5000 Digital Radiation Alert
Monitor
AU
Alpha, Beta, Gamma and X-ray radiation monitor.
Meter, LED, audible indication and detachable
probe. Range 0.1 to 1,000,000 CPM; Accuracy
1% or 2 digits.
Hydrolab Minisonde 5 Multiprobe Water Logger
Narda 8217 Microwave Oven Survey Meter
NAR,8217 (5553)
HYD,MS5 (6024)
AU
W&G RadMan ESM-20 Personal RF Field
Radiation Monitor
AU
Personal monitor and leakage detector
for high frequency electromagnetic fields.
Simultaneous E and H field measurements with audible and visual alarms.
Frequency range H field 1MHz to 1GHz; E field 1MHz to 40GHz. Operation
as personal monitor with compensation for human body absorption, or with
isotropic detection for RF leakage sensing and simple four-level measurement
using LED indicators. Battery powered. Battery life over 200h.
ISCO 6700 Series Water Sampler
ISCO,6712 (6057)
Isco 6700 Series Water Sampler with Bubbler
Flow Module
Severn Model Tortus II
Floor Slip Tester
ISK,6700-730 (6056)
AU
Advanced water sampler for fully programmed
collection. Samples can be collected in 1, 2, 8, or
24, 1 litre disposable sample containers based on
time, flow, and/or parameter set points. Fitted with
NEMA 4X,6 (IP67) sealed controller featuring an
exclusive, built-in pump, flash memory for easy
programming changes, and a plug-in module port
for connection of a flow meter module or parameter measurement module to
enhance monitoring capabilities. Provided with bubbler flow module. Sample
bottles available. Run from rechargeable 12V sealed batteries.
AU
Floor friction tester. Measures and
records the dynamic coefficient of
friction. Applications in assessing floor
safety, evaluating cleaning methods and maintenance procedures, accident
investigation, etc. Meets the draft requirements of international, Australian and
New Zealand standards.
Water Quality, pH Meters
& Electrochem
OTT KL010-150 Ground-water Depth Measurement Contact Gauge 150m
OTT,KL010-150 (6065)
AU
Contact gauge for portable depth to water measurement. Used for wells,
observation pipes, bore holes and control pumping tests. 150m depth of tape.
as soon as the probe touches the water surface an acoustic signal beeps and
the lamp on the instrument lights up. The depth is read from the measuring
tape in meters.
DKK TOA Model RC-24P Portable Residual
Chlorine Meter
DKK,RC-24P-DP (6046)
AU
Advanced water sampler for fully programmed
collection. Samples are collected in up to 24
disposable plastic containers based on time, flow,
and/or parameter set points. Fitted with NEMA 4X,6
(IP67) sealed controller featuring an exclusive,
built-in pump.
Floor Slip Testers
SEV,TORTUSII (5505)
AU
Microsonde 5 multiprobe water/borehole logger,
including ‘Surveyor’ data collection system with
GPS. Includes sensors for Dissolved Oxygen
(HACH LDO), Conductivity, pH, Redox (ORP),
Turbidity (Self Cleaning), Temperature, Depth (0
to 25m) & GPS position. Includes the surveyor
data aquisition system so no laptop is needed for
download or data collection. Includes a 25m cable.
For oven power measurement complete with beaker and thermometer.
Calibration frequency 2.45GHz. Measurement range 0.5 to 10mW/cm2.
Battery operated.
WG,ESM-20 (5557)
AU
Measures pH range 0 to 14pH, resolution 0.01, accuracy ±0.1. Oxidation
reduction potential (ORP) range -2,000mV to 2,000mV, resolution 1mV,
accuracy ±15mV. Dissolved oxygen (DO) range 0 to 50mg/l, resolution 0.01,
accuracy 0 to 20mg/l ±0.2 and 20 to 50mg/l ±0.5. Conductivity range 0 to
100mS/cm, resolution 0.001 to 0.1 depending on scale, accuracy ±1%F.S.
Salinity range 0 to 70ppt, resolution 0.1, accuracy ±3ppt. Total dissolved solids
(TDS) range 0 to 100g/l, resolution 0.1%F.S., accuracy ±5. Seawater specific
gravity range 0 to 50 sigma t, resolution 0.1, accuracy ±5. Temperature
range -5 to 55ºC, resolution 0.01, Turbidity (Turb) 0 to 800NTU, resolution
0.1, accuracy ±5% (reading) or ±1NTU whichever is the greater. The probe
diameter is 96mm the cable length is 10m.
Provides exposure measurements in mR/hr to 50R/h
(0.55v/hr). Detects skin-dose, deep-dose and X-ray
radiation. Measures dose & dose rate.
HPI,CYPHER5000
www.techrentals.com.au
AU
Portable, direct-reading residual chlorine meter for
water analysis. Range 0 to 2mg/L [ppm]. Reagentfree measurement with electrode, 3m cable, float
and sample container for in-situ or grab-sampling.
Compatible with direct chlorination, hypochlorite
or dichloroisocyanurate dosing. Calibration data
stored in electrode with correlation with DPD
methods. Waterproof to IP67. ISO validation
functions, storage of 300 measurements and
RS232 printer output. Battery operated.
Solinist Oil/Water Interface Meter
SOL,122 (6066)
AU
Used for bore determination of LNAPL or DNAPL levels. Flat tape on a reel
when lowered down a bore hole a light and tone indicate the LNAPL (Light
Non-Aqueous Phase Liquid) layer or the DNAPL (Dense Non-Aqueous Phase
Liquid) level. The level is measured from the 50m tape.
74
ENVIRONMENT, OHS, CHEMICAL & LABORATORY
www.techrentals.com.au
Water Quality, pH Meters
& Electrochem cont’d.
Water Quality, pH Meters
& Electrochem cont’d.
TPS 90FL-T Water Quality Meter
TPS,90FL-T (6028)
TPS WP-82 Dissolved Oxygen Meter
AU
TPS,WP-82 (6009)
Field meter and logger for water quality
measurements. Configured with independent
probes for pH, conductivity/salinity[TDS]/
temperature, dissolved oxygen[DO] and
turbidity. Cables 5m with probe holder and
safety harness. LCD display readout with
simultaneous display of all measurements.
Manual, “notepad” storage or automated data logging for up to 1,808 sets of
readings by time and date. RS232C interface, with WinTPS software included.
Supplied with rechargeable battery, and clip-lead for operation from a 12V
source such as a car-battery.
TPS Conductivity Probe With Cell K=0.1
TPS,LOW K PROBE ( 6016)
AU
Portable hand-held dissolved oxygen and
temperature meter. Operating ranges 0
to 20ppm, 0 to 240% saturation, 0 to 45%
gaseous and ppm with salinity correction.
temperature range -10 to 120°C. Case water
resistant to IP67, connectors to IP65, with
3m detachable cable and ED1 electrode.
Menu driven, with alphanumeric display. Auto
storage of time and date of last calibration for
GLP. RS232C interface, and memory for 150 readings of data, time and date,
for Notepad results collection, or for AutoLog results collection with logging
intervals between 1min & 24h. Rechargeable NiMH battery gives up to 75h
operation. Supplied with download-software, charger and solutions.
AU
Plastic-bodied conductivity and temperature sensor for WP series meters.
With k=0.1 and automatic temperature compensation ATC. For precision
measurement at low conductivity levels. Minimum range with WP-84 2 uS/cm
to 2,000uS/cm. Temperature range -10 to 60°C. Fitted with 5m cable.
TPS WP-84 Conductivity Salinity
Temperature Meter
TPS,WP-84 (6014)
TPS Redox Electrode
TPS,REDOX (6004)
AU
Silver/chloride Redox electrode for use with TPS LC80A Ph meter. Supplied
with 2 bottles of Zobell solution for calibration. 1:1 dilution gives approx.
231mV.
TPS WP-80 pH and Temperature Meter
TPS,WP-80 (6003)
AU
Portable hand-held meter for pH, mV and
temperature. Supplied with combination pH
electrode and separate temperature sensor on
1m cables. Operating ranges 0 to 14pH and
-10 to 120ºC (automatic sensor recognition
with auto pH correction 0 to 100ºC).
Case water resistant to IP67, connectors to IP65. Menu driven, with
alphanumeric display. Auto storage of time and date of last calibration
for GLP. Memory for 2400 readings of data, time and date, for Notepad
results collection, or for AutoLog with logging intervals between 1s
and 90h. Fitted with RS232C interface and supplied with downloadsoftware, charger and solutions. Rechargeable NiMH battery gives up to
50h operation.
TPS WP-88 Turbidity & Temperature
Meter with 8m Cable
TPS,WP-88 (6031)
AU
Portable
hand-held
turbidity
and
temperature meter for field or laboratory
use. Sensor probe diameter 45mm,
with 8m cable. Turbidity ranging 0.1 to
200/2,000NTU ±1NTU with autoselection.
Temperature compensation and sensor
range 0 to 60ºC ±0.1ºC. Case water
resistant to IP67, connectors to IP65, with detachable cable and sensor. Menu
driven, with alphanumeric display. Auto storage of time, date and results of
last calibration for GLP. RS232C interface, and memory for 150 readings
of data, time and date, for Notepad results collection, or for AutoLog results
collection with logging intervals between 1min and 24h. Rechargeable NiMH
battery gives up to 50h operation. Supplied with download-software, charger
and calibration solutions.
TPS WP-80 pH and Temperature
Meter for Testing Meat
TPS,WP-80M (6002)
AU
Portable hand-held meter for conductivity,
TDS (Total Dissolved Solids) and
temperature. Automatic range selection
with 5 ranges. Case water resistant to IP67,
connectors to IP65. Menu driven, with
alphanumeric display for full-text prompting.
Storage of time and date of last calibration for
GLP. Memory for 150 readings of data, time and date, for Notepad results
collection, or for AutoLog results collection with logging intervals between
1min & 24h. Rechargeable NiMH battery gives up to 75h operation. Supplied
with sensor (k=1), charger and solutions.
AU
Portable hand-held meter for pH, mV and temperature.
The instrument is capable of applying Bendalls
equation to the pH reading for Meat Standards
Australia grading requirements. Supplied with
combination pH electrode and separate temperature
sensor on 1m cables. Operating ranges 0~14pH and
-10~120ºC [automatic sensor recognition with auto
pH correction 0~100ºC]. Case water resistant to IP67, connectors to IP65.
Menu driven, with alphanumeric display. Auto storage of time and date of
last calibration for GLP. Memory for 2400 readings of data, time and date, for
Notepad results collection, or for AutoLog with logging intervals between 1s
and 90h. Fitted with RS232C interface and supplied with download-software,
charger and solutions. Rechargeable NiMH battery gives up to 50h operation.
Van Essen DI502 Mini-Diver Borehole
Level Logger & Barometer 20m
VAN,DI502 (6061)
AU
Mini-diver borehole level logger 20m, 1cm
accuracy. Kit includes barometric logger for
atmospheric pressure compensation. Will
also log temperature. Temperature range
-20 to 80ºC. Accuracy 0.1ºC. Size 22 x
90mm. Stores 24,000 measurements per parameter. Stainless steel housing
barometric (l/c) logger for compensation. 10 year battery life.
75
ENVIRONMENT, OHS, CHEMICAL & LABORATORY
Light Meters, UVA/B/C
Measurement
Weather Stations
Environdata WeatherOne Wind Speed & Direction Logger
ENV,DL20WSD (5886)
Hioki 3423 Lux HiTester Digital
Illuminance Meter
HIO,3423 (5602)
AU
Logging system for wind speed and direction. Tripod-mounted crossarm stand with 3-cup wind speed sensor range 0-75m/s and independent
vane direction sensor. Sealed dual-channel logger with memory for 35,000
readings with time and date, fitted with backup battery, rechargeable sealed
main battery and solar panel for in-field recharge. Power supply for charging
or operation from mains supply. “EasiAccess” software on CD for office or
field connection via RS232C compatible computer (not included), for setup, download and real-time operation, with functions for tabular or graphical
display.
AU/MY
Manual switching and autoranging.
LCD display with 3½ digits (“1999”)
for five measuring ranges to
20/200/2,000lx in 1-count steps,
20,000lx in 10-count steps and
200,000lx in 100-count steps with accuracy ±4%. Response time in autorange
mode 5s (2s in manual range mode). Autozero, hold and backlight function with
delay for taking readings in low light. Input for AC power adaptor, connectingcable to allow separation of sensor unit and meter, and 200mVDC analogue
output with cable. Battery powered.
Environdata DL20WSD WeatherMaster
2000 Weather Station
ENV,WM20 (5888)
AU
International Light model 1400
radiometer with backlit LCD
display, autozero and autoranging.
Continuous reading with hold
function, or integrated “dose”
measurement up to 24h. Smart
detectors with storage of units and detector-calibration data. Analogue recorder
output. Mains adaptor or battery power. Supplied with three sensors: UV
actinic hazard (UVC with B & A components matched to OSHA requirements),
range 2.50e-7 to 2.50e-3 W/cm2 eff. UVB + A (total “solar” radiation), range
1.16e-7 to 4.07e-1 W/cm2. UVB, range 1.54e-6 to 1.54e-2 W/cm2.
Environmental Flow Meters
See also Flow Meters for Liquids & Gases on page 56-57
Global FP101 Digital Water Velocity Meter
GLO,FP101 (6147)
Minolta CL-200 Chroma Meter for Illuminance
& Colour Measurement
MIN,CL-200 (5610)
AU
Hydrological Services Universal Current
Meter OSS-B1
Topcon BM-9 Luminance Meter
HYS,OSSB1 (6145)
Portable luminance meter with digital display. Field-of-view 5°, measurement
acceptance angle 2°, with 10mm min spot diameter. Measuring distance
0.35m to infinity. Silicon photodiode sensor with automatic or manual range
selection. Measurement range 0.01 to 199,900cd/m2 ±4% of reading. Built-in
RS232C interface and analogue output. Battery powered.
Topcon IM-2D Lux Meter NATA Certification
AU
Digital illuminance meter with NATA certification.
Measuring range from 0.1 to 19,999lx. Accuracy
5%, ±1 digit. Autoranging with silicon sensor.
Battery operated.
Unidata 6526B-21LCD Open Channel Liquid Flow Logger with LCD
Module
UNI,6526B-21LCD (6141)
AU
Digital wide-range illuminance meter with NATA certification. Measuring range
0.01 to 199,000lx. Accuracy ±2% +1 digit. Autoranging with silicon sensor.
Analogue output and RS232 interface. Battery operated.
Yokogawa 51001 Lux Meter NATA Calibrated
YEW,51001-NATA (5607)
AU
Open channel flow logger with field LCD display module and 10m cable [2m
depth rating]. Measurement and logging of flow-velocity [by Doppler], depth
(by pressure) and temperature. Programmable for flow-channel profile [laptop
PC required for in-situ programming via RS232C]. Operating temperature
range 0 to 60°C. Velocity 21 to 5,000 mm/sec ±2%; depth 0 to 2,000 mm ±2%;
temperature: -17 to 60°C ±0.1; log-interval 5 sec to 1 week; memory 120K.
Programmable output to control devices such as water samplers. Detects
and measures reverse flows. Charger and batteries supplied. Workhead
dimensions 290 x 70 x 25mm.
Topcon IM-5 Lux Meter NATA Certification
TOP,IM-5-NATA (5608)
AU
Water current meter for measurement of flow
velocity in rivers, streams, channels and open
water. Robust streamlined stainless body fitted
with high precision 100mmØ fan [flow range
0.025 to 5m/s]. Set of stainless wading rods for depths to 3m. Rechargeable
“Hydromate” ruggedised field computer with IP65 case. Storage of fan
calibration formulae for direct readout of volume-flow. Touch screen entry for
set up, input, storage and download. Supplied with PC download software
and cable.
AU
TOP,IM-2D-NATA (5606)
AU
Portable flow probe - current meter for water velocity
measurements in streams, channels and partially filled pipes.
Propeller sensor in 50mmØ housing, fitted to telescopic handle
[1.8m] with gauging marks to 900mm depth. Digital LCD flow
meter display for instantaneous liquid velocity and average,
maximum, stopwatch or clock. Minimum depth about 50mm.
Range 0.1 to 4.5m/s ±0.05.
Konica Minolta model CL-200 portable colour meter. LCD
display for illuminance, tristimulus values, chromaticity,
correlated colour temperature and colour difference.
Illuminance range 0.1 to 99,990lx ±2%. Colour accuracy
±0.002 [xy] or ±20°K [Tcp]. Fitted with RS232C interface.
Battery powered, or AC adaptor.
TOP,BM-9-2 (5611)
AU
Measures air temperature -15 to 50°C ±0.2, relative
humidity 10 to 90%RH ±5%, rainfall 0.2mm resolution.
Wind speed starting threshold 1kph. Wind direction
resolution 6°C ±3%. One spare input channel.
Capable of storing up to 3mths of data. Includes
RS232 interface and software for download. Mounts
on star-picket. Solar-rechargeable batteries.
ILI 1400ABC Radiometer for UV
Measurements
ILI,1400ABC (5614)
www.techrentals.com.au
AU
Digital illuminance meter with NATA certification. Measuring range from 0 to
99.9/999/9,990/99,900/999,000lx . Accuracy <3,000lx 4% ±1 digit >3,000lx
6% ±1 digit. Autoranging with silicon sensor. Battery operated.
76
www.techrentals.com.au
ENVIRONMENT, OHS, CHEMICAL & LABORATORY
Laboratory & Hand-held
Microscopes
Chemical & Analytical - General
Hydramotion Viscolite 700 Portable Viscometer
HYL,V700S-21 (6352)
Proscope SCA-12770 Video Microscope Kit
PRO,SCA-12770 (5137)
AU
Hand-held USB video microscope complete kit. Includes 200X, 100X, 50X,
1 to 10X interchangeable lenses, C Mount adaptor, stand and carry case.
Connects to a PC via USB interface. Software allows snap shot still images
and real time movie files to be saved. Resolution is 640 x 480 pixels.
Balances & Scales below 8kg
Laboratory Instruments,
Spectroscopy
See also Weighing & Counting Scales over 8kg on page 61
A&D HF-300G Mercury 300g Counting Scales
AND,HF-300G (4439)
X-Rite SP60 Portable Sphere Colour Spectrophotometer
AU
XRI,SP60 (6342)
Scales 310g, resolution 0.001, repeatability 0.001. Includes RS232 port.
Includes counting software. Can be used as counting scales.
AU
Portable spectrophotometer for surface colour measurements. Diffuse 8°
[d/8] optical geometry with fixed 8mm aperture. Tungsten source for illuminant
types C, D50, D65, D75, A, F2, F7, F11 & F12. Standard observers 2 & 10°.
Blue-enhanced photodiode detectors with spectral range 400 to 700nm.
Measures opacity and colour by chromatic, apparent or tristimulus calculation,
with simultaneous included and excluded specular component, and spectrum
at 10nm intervals. Storage of up to 2,000 samples with results download to
serial printer or computer. Operation from internal rechargeable battery or AC
adaptor.
A&D Mercury MX50 Moisture Balance
AND,MX50 (4440)
AU
Advanced portable viscometer with stainless-steel probe. Operating range
0.1 to 10,000mPaps (cps) with integral temperature correction -40 to 150ºC.
Probe tip 21mmØ, immersion length 115mm (viscosity only) or 145mm
(viscosity/temperature). Acetal polymer probe base for handheld or clamped
operation, with coiled-cable connection to meter unit with 5 digit display.
Battery powered.
AU
Maximum sample weight capacity 51g, weight resolution 0.001g, moisture content accuracy over 1g 0.10%, over 5g 0.02%. Halogen lamp used for heating,
400watt max. Drying temperature 50 to 200ºC. Measurement programs 20 sets,
measurement mode moisture content, wet or dry, dry content, ratio, weight.
Heating mode standard, automatic, quick, timer, manual. Display large VFD,
interface RS-232C, CD-ROM S/W supplied. Pan sample size diameter 85mm.
Ohaus EXP4100 4100g Balance and Counting Scale
OHA,EXP4100 (4432)
AU
Capacity 4.1kg. Display resolution 0.01g. Multi-unit display. Repeatability
0.005g. RS232 interface.
Have your OH&S Communications made easy
with TR Bearcom Solutions!
TR Bearcom has Factory Mutual (FM) rated two
way radios and equipment that are suitable for a
wide range of applications.
The Motorola MTP850Ex TETRA ATEX and IEC Ex is the
ideal two way radio for environments containing potentially
explosive gas and dust.
FM radios are available in all frequency bands:
Features:
• VHF (136-174 MHz) two way radios
• IP64 (Cat 2) rating
• Can be operated in gas zones 1 and 2
classified hazardous areas (Ex ib IIC T4)
• Can be operated in dust zones 21 and 22 classified
hazardous areas (Ex tD A21 IP6x ib D21 T90˚C)
– Good long distance line of sight coverage,
e.g. open water
• UHF (403-470 MHz and 450-527 MHz) two
way radios
– Good mixture of both penetration and distance
bearcom
no1 in radio solutions
77
Check Out Our New
Online Store
www.trbearcom.com.au
BS0322
Accredited FM
irer
approved repa
OTHER PRODUCTS
www.techrentals.com.au
Security Equipment
Prospecting Metal Detectors
AVE Serial to Video Converter Including Video Mixer
AVE,VSIPLUS (9218)
See also Underground Services Location on page 66-67
AU
Excaliber 1000 Underwater Metal Detector
Mixes serial data (text) with video signal, so that a picture includes this text.
Use with a GPS (eg GA,ETREX) to add a location reference to a video or
used with cash register RS232 output to record transactions on a security
camera picture.
EXA,1000 (9204)
MIN,EX-1000
Underwater metal detector with 10 inch search coil. Can be used effectively in
or out of the water and is capable of going down to 60 meters depth. Features
two operating modes; all metal and discriminate. In discriminate mode it will
ignore most ferrous objects and still detect the valuable non-ferrous objects
such as gold and silver. Rechargeable battery pack separated from the
electronics cylinder allows easy access for recharging.
4 Camera Surveillance Digital Stand-Alone Record System
CAM,DVMR-4C (9255)
AU
MY
AU
4 day/night colour cameras with stand-alone digital video multiplex recorder,
complete system with 15” colour LCD screen, 20m connection cables, power
supplies and video to USB converter for down loading of data to PC.
Minelab Discriminating Metal Detector
Detec DH50 Hand-held Metal Detector Kit of 4
DET,DH-50-KIT4 (9208)
MIN,X-TERRA-705 (9205)
Kit of 4 x hand held security metal detector. Simple to operate - no adjustment
needed. Audible alarm.
Detec Garrett CS5000 Walk Through Metal Detector
GAR,CS5000 (9211)
AU
Detects all metals. Requires assembly on-site & set-up. Adjustable
sensitivity.
Retail Customer Traffic Flow
Counters
Traffic Pro People Counter Event Logger
TRA,RETAILPACK (9210)
AU
Discriminating metal detector. Useful for locating lost
coins rings etc. Preset operating modes depending
upon what is required. Preset noise cancelling.
AU
AU
Counts the number of people passing a particular point. Used to check the
success of in-store promotions, counting people entering sections of a store,
etc. The unit operates from internal batteries and will store a year of data at a
1h sample rate.
NOTES
78
NOTES
www.techrentals.com.au
79
OUR STRENGTH LIES IN OUR STRONG TECHNICAL CAPACITY AND THE
SYNERGIES BETWEEN OUR DIFFERENT BUSINESS UNITS.
Test & Measurement
Satellite Communications
TechRentals offers specialised test equipment
product solutions for a wide range of industries.
Products offered include power measurement and
analysis, general electronic, environmental and
OH&S, plus telecommunications. The leader in
the industrial rental arena for more than 30 years,
TechRentals also offers flexible purchasing options
on selected product ranges.
TR Telecom is the region’s largest satellite telephony
service provider, with a customer support team
working from the Australian head office in Melbourne
and offering comprehensive product sales and
connections to the global Iridium network. TR Telecom
is also proud to announce that it is an authorised
reseller of NewSat communications. With coverage
around Australia, New Zealand and surrounding
island regions, you are able to stay connected with
world class satellite solutions.
www.techrentals.com.au
www.techrentals.com.my
www.trtelecom.com
1800 632 652
1300 550 014
Audiovisual & Business Equipment
Calibration
TR Vidcom is raising standards in the dynamic
computer and audio-visual industry, offering solutions
for both short & long term equipment procurement and
event management. TR Vidcom has superior product
and industry knowledge, with a nation-wide service
over 9 locations across Australia. We can provide
all your computer and audio-visual requirements,
with national support and timely delivery of your
equipment. Our customers include major corporate
companies around Australia and event managers
around the nation. We can deliver, install and fully
train your staff on your premises.
Utilising state-of-the-art technology, our experienced
team delivers calibration and repair services to
customers in defence, manufacturing, aviation and
other high tech sectors. TR VMS calibration group
has NATA accredited facilities in Australia, plus
mobile calibration labs operating as needed to meet
customers’ on-site demands.
www.trvms.com.au
1300 790 480
Radio Communications
www.trvidcom.com.au
1800 843 266
TR Bearcom is the largest and most awarded
two-way radio communications rental company in
Australasia and a division of TR Pty Ltd. Whatever
your business needs, TR Bearcom have the
resources to develop a customised solution that is
competitively priced and of the highest standard,
using state-of-the-art two-way radio communications
technology from the world’s leading manufacturers.
Mining Communications
TR Minecom is an Australian technology company
specialising in communications and safety systems
for underground mining. Established in the 1980s,
TR Minecom has built a solid reputation as a world
leader in underground mining communication systems, in particular leaky feeder systems. TR Minecom
offers a range of leaky feeder solutions designed to
ensure high levels of safety and productivity.
www.trbearcom.com.au
www.trbearcomrental.com.au
1800 222 327
www.minecom.com
1800 135 901
80
TECHRENTALS BUSINESS PARTNERS
www.techrentals.com.au
Acoustic Research
Laboratories
Anritsu
EXFO
Fluke
Fluke Networks
Gridsense
JDSU
Megger
SebaKMT
Testo
TECHRENTALS ARE DISTRIBUTORS AND RESELLERS FOR:
Anritsu
Acoustic Research Laboratories
JDSU
SebaKMT
Megger
Kingfisher
Gridsense
Flir
TECHRENTALS - THE PERFECT SOLUTION!
TechRentals has a vast fleet of products offering solutions for many markets including
Aviation, HVAC, Defence, Electrical, Biomedical, Mechanical and Telco markets,
however if you cannot find what you are looking we have access to our international
partners giving you an even larger and deeper inventory to satisfy your needs.
Remember that it is much more cost effective to Rent than to purchase outright as you are able to utilise
capital expenditure in other parts of your business, however if you do need to eventually own the assets
than Tech Rentals will offer a Rent with Purchase Option, either way we will find you the assets you need
when you want them.
81