Gauges IMPORTANT INFORMATION: Product must be installed and used in strict conformance with NFPA Pamphlet 58 and/or NFPA Pamphlet 54 and all other codes, regulations and manufacturer recommendations. Failure to follow these codes, regulations and recommendations could result in hazardous installation, bodily injury and/or death. PRODUCT TRAINING SCHOOLS AVAILABLE. Contact a GEC customer service representative for more information. WARNING: LP Gas is extremely flammable and explosive. Devices used for handling LP Gas and Anhydrous Ammonia must be installed and used in strict conformance with NFPA Pamphlet 58 and 54 and all other codes, regulations and manufacturer recommendations. 209 How To Order A Gauge Tank configuration shown is appropriate for tanks built since the mid-1970’s. If yours does not match, please call the Gas Equipment Company location nearest you and we will be glad to help. 1. Determine Tank Type ❏ Above Ground ❏ Under Ground 2. Determine Gauge Head Type ❏JR - 4 bolt A = 2-1/32 ❏ SR - 4 bolt ❏ 1-1/4” Thread A = 2-1/2 ❏ 1” Thread 3. Determine Tank Diameter D = _______ “ From Tank Data Plate or Measure Circumference (in inches) and divide by 3.14 4. Determine Riser Height: H = ________ “ Note: Riser height is the distance, in inches, from tank surface to top of mounting flange or coupling for gauge. Distance "H" Dimension "H" "H" Dimension "H" Height Footring 5. Determine Mounting Position Top Mount Angle Mount Center Line End Mount ❏ Top Mount ❏ Angle Mount ❏ Side Mount ❏ End Mount Side Mount Note: Pivot point of float must be at center line of tank. 210 Adjustable Liquid Level Gauge Here is an adjustable, magnetic, liquid-level gauge which makes it a snap to quickly and economically replace non-functional LP Gas gauges in the field. Because one size adjustable gauges fit many tanks, the ‘One’ Gauge greatly reduces the number of spare gauges you need to stock. The ‘One’ Gauge is UL listed for LP gas service. Junior™, 4-Bolt Adjustable Gauges Part # Adj. Stem Length Application 0049S02159 12 1⁄2” to 19 3⁄4” Above Ground Senior™, 4-Bolt Adjustable Gauges Part # Adj. Stem Length Application 0049S02207 12 1⁄2” to 19 3⁄4” Above Ground Junior™ Brass Threaded Adjustable Gauge 1 1⁄4" NPT Threaded Part # Adj. Stem Length Application 0049S02203 12 1⁄2” to 19 3⁄4” Above Ground 1" NPT Threaded Part # Adj. Stem Length Application 0049S02160 12 1⁄4” to 19 3⁄4” Above Ground Common Junior™ & Senior™ Float Assemblies - Top Mount Part # Tank Diameter 6857S11009 6857S13759 6810S14379 6857S17009 24” 30” 32” 37.5” Assembly Instructions B6287-4 STEP 1: **NOTE: THESE ASSEMBLY INSTRUCTIONS ARE GOOD FOR MODEL #'S 6285-, 6287, 7287-, & 8987OLD GAUGE LENGTH SELECT FLOAT ARM TO FIT TANK NEW GAUGE TO OLD GAUGE LENGTH STEP 4: INSERT BRASS BEARING, 0109-00495, THROUGH OTHER SIDE OF GEAR HOUSING FLOAT ARM TO BE INSERTED FROM FRONT SIDE SO THAT SINGLE BLACK MARK ON FLOAT ARM GEAR FITS BETWEEN TWO WHITE MARKS ON PINION GEAR. STEP 5: GEAR HOUSING LOCKNUT B6287-4 CENTERSHAFT "R" LOGO MARK OR SCRIBE CENTERSHAFT AS SHOWN STEP 2: ORIGINAL MARK FROM STEP 1 CUT OFF EXCESS CENTERSHAFT JUST BELOW MARK AS SHOWN INSERT SCREW, 0040-00479, WITH #1 PHILLIPS SCREWDRIVER PROPERLY TIGHTENED INCREASE SUPPORT LENGTH BACK TO OLD GAUGE LENGTH AT STEP 7: . C C Y YL L. 80 HES C HES RO ROC FILL FILL TER GAU GAU 30 GES GES INC. INC. OF OF 90 95 ING ING 20 TEX TEX AS AS UL 10 U.S.A. DAL DAL LAS TX. U.S.A. LAS TX. 5 NO. NO. DIAL DIAL B6287-4 H R IZ Z .. TA AN NK ND T UND KS S ROOU MAX. MAX. LEVE GR LEVEL % %TTO EG L OTT VE LIQUID AT AT LIQUID O OV AALL BB PP.. ˚F TEM TEM ˚F AA VV 20 60 60 80 00 20 80 100 BBUU 100 BBUU 120 120 RROORROO 0P 0P PP 00 70 DO NOT USE FOR 60 50 40 55 / 55 O O CAREFULLY RETIGHTEN ORIGINAL MARK LINES UP WITH EDGE OF LOCKNUT DIAL SHOULD READ APPROXIMATELY 45-50% WITH FLOAT ARM AT 90º TO SUPPORT. MOVE FLOAT ARM UP AND DOWN TO CHECK FOR FREE MOVEMENT E E M M SHAFT IS NOW RECESSED U LLU O O B6287-4 CHECK FOR FREE MOVING PINION AND CLEAR HOLE 33 STEP 3: STEP 6: 27 TEMPORARILY ADJUST SUPPORT SHORTER THAN THE MARK ON CENTERSHAFT 5- MARK NEW GAUGE AS SHOWN TO BE LOOSENED 211 ASME Tank & DOT Cylinder Gauges Rochester Gauge Information Rochester gauges are the standard of excellence for measuring LPG levels. Stainless steel bearing surfaces and self-aligning bevel gears ensure extremely long life. The one-piece, die-cast plastic gear housing is designed to protect gear operation. The nitrile float is another exclusive development of Rochester engineers. This lighter float lets Rochester use a lighter counter weight which lengthens gauge Junior™, 4-Bolt Gauges Furnished with gasket, dial, and 4 mounting bolts. Part # 6281 Bolt circle* Description Mounting bolt Top mounting 2 1/32 6284 (4) 1/4" - 28 Side, end or angle mount *Measured diagonally Senior™, 4-Bolt Gauges Furnished with gasket, dial, and mounting bolts. Part # Bolt Circle* 6280 Description Mounting Bolt Top mounting 6283 Side, end or angle mount 2 1/2" (4) 5/16" - 24 6290 Top mounting with 4" dial 6293 Side, end or angle mount with 4" dial *Measured diagonally Junior™, Threaded Gauges 1-1/4" NPT Threaded Part #* Description 7281 Zinc head, top mounting 7284 Side, end or angle mount Hex 2" 1" NPT Threaded Part #* Description Hex 8981 Top mount 2" Part #* Description Hex 7381 Top mount 7384 End mount 3/4" NPT Threaded 2" *Use “B” prefix for Brass head gauge, ie: B7384 Brass Head Gauge 212 life particularly where vibration is a factor. Dial chambers are hermetically-sealed, moisture-proof and easily replaced without exposing the contents of the tank. The one-piece gauge head is die cast from a high-tensile strength aluminum alloy. All Rochester 6200 Series gauges are UL listed for LP gas service. NH3 Gauges The A6200 series gauges are designed to withstand the corrosive rigors of NH3 service. The A6400 series is all-stainless-steel construction designed to withstand NH3 with chemical additives. All “A” prefix gauges are UL listed for NH3 service. These gauges come standard with direct-reading percentage dials. Junior™, 4-Bolt Gauges Furnished with gasket, dial, and 4 mounting bolts. Part # Description A6281 For top mounting. Includes standard magnet to drive direct-reading dials. A6284 For side, end or angle mounting. Senior™, 4-Bolt Gauges Furnished with gasket, dial, and 4 mounting bolts. Part # Description A6280 For top mounting. Includes standard magnet to drive direct-reading dials. A6283 For side, end or angle mounting. Senior™ N-Serve Gauges All stainless steel construction. Furnished with gasket, dial, and 4 mounting bolts. Part # A6480-00012 A6480-00013 Description For top mounting, N-Serve Gauge A6200 Series Gauge For Tank Diameter 46" 41" Replacement NH3 Dials Part # Description 5323S01848 Junior 5002S00002 Senior Replacement Gaskets - NH3 Compatible Part # Description 0015-00855 Junior 0015-00836 Senior 213 Lift Truck Gauges Perfect for most forklift cylinder replacement. Junior™, 4-Bolt Gauges Model # Cylinder Size Mounting Dial # Universal 5343S01823 14 lb. 9" I.D. Horizontal 5323S01789 Vertical 5323S01819 Universal 5343S01815 Horizontal 5323S01789 6284-32 6284-39 6281-5 6284-33 6284-24 20 lb. 12" I.D. 6281-45 Vertical 5323S01818 6284-34 Universal 5343S01791 Horizontal 5323S01789 6284-24 33 1/2 lb. 12" I.D. 6281-48 Vertical 5323S01820 6284-35 Universal 5343S01824 Horizontal 5323S01789 Vertical 5323S01821 Universal 5343S01791 6284-24 43 1/2 lb. 12" I.D. 6281-49 6284-46 6284-45 60 lb. 14" I.D. Horizontal 5323S01789 6281-50 Vertical 5323S01817 6284-45 Horizontal 5323S01789 6281-38 Vertical 5323S01813 Vertical 5323S01814 Vertical 5323S01816 6281-39 100 lb. 14 1/2" 6281-47 Junior™, Polymer Construction Gauge 3/4" NPT Threaded This gauge measures the liquid contents of a horizontally mounted lift truck cylinder. The gauge has a second scale for use when the tank is stored vertically which reads “OK” or “ADD”. The gauge head accepts a snap-on Junior™ dial and has 1 3⁄8" [35] hex wrenching flats. The gauge support, center shaft and float arm are constructed of a propane compatible thermoplastic polymer material. This construction reduces the number of parts and improves reliability and accuracy. Model # Cylinder Size 7384-4021 20, 33.5, 43.5 bl 214 Mounting Universal Dial 5714S02591 Lift Truck Gauges Junior™, Threaded Gauges 1-1/4" NPT Threaded Rochester‘s all aluminum and stainless steel gauges are ideal for rugged, trouble-free, lift truck service. Features include the hermetically-sealed, magnetically-coupled, easily-replaceable dial. Model # Cylinder Size Mounting Dial # Universal 5343S01815 Horizontal 5323S01789 Vertical 5323S01818 7284-33 7284-24 20 lb. 12" I.D. 7281-45 7284-34 7284-24 33 1/2 lb. 12" I.D. Universal 5343S01791 Horizontal 5323S01789 Vertical 5323S01820 7281-48 7284-35 7284-24 43 1/2 lb. 12" I.D. Universal 5343S01824 Horizontal 5323S01789 Vertical 5323S01821 7281-49 3/4" NPT Threaded Stainless steel gears & bearings guarantee longer service. There is a gauge for all size containers and any mounting position. Model # Cylinder Size Mounting Dial # 7381-1003 14 lb. 9" I.D. Vertical 5323S01915 Universal 5343S01912 Horizontal 5323S01944 7384-1002 Vertical 5323S01914 7384-1006 Universal 5343S01992 7384-1005 7384-1008 7384-1008 7384-1007 7384-1008 7384-1010 20 lb. 12" I.D. 33 1/2 lb. 12" I.D. 43 1/2 lb. 12" I.D. 60 lb. or 100 lb. 14 1/2" I.D. Horizontal 5343S01944 Universal 5343S01993 Horizontal 5343S01944 Horizontal 5323S01944 215 Motor Fuel Gauges & Farm Tank Gauges Motor Fuel Gauges Zinc head gauge with heavy-duty magnet. Ideal with remote reading replaceable Twinsite® Sender. Tank Dia.(") Tank Mfg. Rochester Part # 8 Manchester 6244-00600 B** H8LN 320 DR Brunner Brunner Brunner Manchester 6244-605 6244-00032 6244-00046 6244-00353 H8AB H10AB Lower 45 315 H10C CENTER DR DR DR DR Brunner Brunner Manchester 6244-00047 6244-00094 6244-00354 H12C CENTER Manchester Brunner Brunner 6244-00384 6244-00048 6244-00097 10 12 13 14 16 Brunner 6244-00054 Manchester Manchester 6244-00334 6244-00599 Brunner Brunner Brunner Brunner Manchester Brunner Brunner 6244-00049 6244-00100 6244-00055 6244-00105 6244-00338 6244-00050 6244-00106 Manchester 18 20 Mounting Angle H13LN 320 H13C CENTER H14A 45 H14LN 320 H14C CENTER H16A 45 H16C CENTER 6244-00604 B** Brunner 6244-00056 Manchester Brunner Brunner Manchester Brunner Manchester Brunner 6244-00340 6244-00051 6244-00109 6244-00357 6244-00058 6244-00342 6244-00052 Manchester 6244-00358 Brunner Dial Type* DR TS DR DR DR TS DR DR DR DR TS DR TS DR DR TS DR DR H18A 45 H18C CENTER H20A 45 H20C CENTER 6244-00344 H22A 45 DR Brunner 6244-00343 H22C CENTER DR Brunner 6244-00074 Manchester Brunner 6244-00181 6244-00073 H24A 45 Manchester 6244-00371 H24C CENTER Brunner 6244-00085 H30C CENTER 22 24 Gauge Head Stamp 30 *DR = Direct Read Dial **B = Brass Head DR DR TS DR DR DR DR DR DR DR DR DR DR TS = Twinsite® Sender Farm Tank Gauges These lever-action gauges are designed for use in stationary farm tanks or other tanks with flat heads. They are to be mounted on the centerline in the middle of the head. The maximum recommended float length is 48". Part # Description Application F7183 Lever-Action Gauge 1 1/2" NPT Stationary farm tanks or tanks with flat heads. 5001S00605 Stationary tanks. Fractional dials Vibration dampened for mobile tanks. 5002S00605 For correct float-rod sizing and installation, refer to the figure below. ⁄2 Tank height minus 2" 1 File notch near end of float rod ⁄4” 1 216 Bulk Storage Gauges Magnetel™ Gauge Models Rochester Magnetel™ Liquid Level Gauges are available in 4" and 8" dial sizes. Standard calibration is percent of total tank volume. Model # Mounting 6336 -11 Top Dial size 4" 6339 -11 Side, end or angle 6342 -11 8" Top 6360 -11 Materials Code/Trim # Chart Trim # Type Service Gauge Flange -11 LPG or NH3 Type 316 stainless steel Bearing Float & Stem Float support support drive Counterbalance block tubing magnet Cold-roll steel - zinc plated Type 303 stainless steel Alnico VI All other parts 300 series stainless steel Trim 11 should be used on containers of 3500 WG or more. Gauges for vertical tanks require drawings for computing proper gauge dimensions & mounting locations. More trim levels available for other products. Specify prefix for appropriate dial & mounting Dial Prefix “C” = Combination LPG/NH3. Mounting Prefix “X” = When straddle mounting is required. “Y” = When ordering gauge for 2" opening. “M” = Special mobile. “V” = Vertical tank. When ordering specify: • Liquid product and specific gravity. • Type vessel, inside diameter (in inches) & head type (ellipsoidal, semi elliptical, hemispherical). • Prefix (see chart). • Model # for mounting location (top, side, 8" or 4" dial). • Trim # according to product compatibility requirements.* • Bolt hole location of mounting flange • If other than standard percent of total volume dial is required. • Top-mounted gauges require dimension from mounting flange face to tank shell plus shell thickness. • Angle-mounted gauges require tank drawings for computing proper gauge dimensions. Common Magnetel Configurations Part number example Prefix Model # Trim # Diameter CX Combination LPG/NH3 6342 11 108" See trim chart Side, end or angle mounted 8" dial Part # C6342-11-84 Diameter Of Tank 84" C6342-11-108 108" C6342-11-130 130" Special calibration dials are available at extra cost. Please state requirements. Special gauges made to order. Straddle mounted 217 Transport Gauges Ideal for LPG or NH3 bobtails and transports. Also available for CO2 use. Magnetel ™ Rough Rider™ Gauges The Rough Rider™ is designed to withstand the vibration and shock inherent in mobile service. Their service life in over-theroad and off-road transports carrying liquids including LP Gas, NH3, and cryogenic liquids is unsurpassed. These gauges provide accurate indications of liquid level at a glance, making inconvenient rotary gauges obsolete. Rough Rider™ gauges are equipped with an exclusive spring steel shock absorber on the float arm which substantially reduces the stress that can quickly destroy conventional gauges. Common Rough Rider™ Configurations Part # “C” = Combination LPG/NH3. “D” = Insulated extension for CO2 and other cryogenic liquids. Mounting Prefix “M” = Special mobile mounting. When ordering specify: • Liquid product and specific gravity. • Type vessel, inside diameter (in inches) & head type (ellipsoidal, semi elliptical, hemispherical). • Prefix (see chart). • Model # for mounting location (top, side, 8" or 4" dial). • Trim # according to product compatibility requirements.* • Bolt hole location of mounting flange • If other than standard percent of total volume dial is required. • Top-mounted gauges require dimension from mounting flangeface to tank shell plus shell thickness. • Angle-mounted gauges require tank drawings for computing proper gauge dimensions. Eliminator™ Rotogauge Replacement 1" NPT A direct-reading float gauge that is a direct replacement for rotary-type, dip-tube gauges in LP and NH3 storage tanks. Only intended for use in tanks with fixed, liquid-level gauges. Part # Description For mobile or stationary tanks up to 44" in P6293-R4400 diameter P6293-R6000 For mobile or stationary tanks greater than 44" & up to 60" in Diameter P6293-R7200 For stationary tanks greater than 60" & up to 72" in Diameter P6293-R8400 For stationary tanks greater than 72" & up to 84" in diameter 218 Diameter of tank 72" CM6339-11-79 79" 4" CM6339-11-84 84" CM6339-11-96 96" Also available with 8" dials upon request. Other size supports available by special order. Specify prefix for appropriate dial & mounting Dial Prefix Dial CM6339-11-72 Bulk Storage & Transport 1" Rotogages® for Large Mobile and Stationary Containers Rotogages® are designed to provide an accurate determination of LPGas or anhydrous ammonia container contents. They mount in a standard 1" NPT coupling on large mobile or stationary containers. To operate the Rotogages®, the vent valve is opened and the dip tube rotated slowly from the container vapor space to the liquid space. The difference in appearance of the discharge indicates when the liquid level is reached. Dial readings then indicate the percentage of product in the container. Rotogage® Dials Part Number Service A9091-18L LP-Gas All Sizes A9091-18LX* LP-Gas Over 1200 U.S. gallons A9091-18N NH3 All sizes Container Size * Dial permits higher filling level, as per NFPA 58, (1983) Par. 4-5.2.1, Table 4-5.2.1 Rotogage® Ordering Information For Container Inside Diameter Part Number For Dip Tube (Ordered Separately) For Use With LPG or NH 3 For Mobile or Stationary Containers For Stationary Containers Only A9091R A9092R Ellipsoidal Heads Standard Dip Tube Part No. A9091-M24.0 Side Mounted — Standard Dip Tube Length 24" — 36" A9091-M36.0 A9093TS* A9093RS 48" A9094TS* A9095TS* A9094RS A9095RS 60" 72" Hemispherical Heads End Mounted Side Mounted End Mounted 30" - 45" 30" - 75" 30" - 45" 30" - 45" 46" - 61" 76" - 108" 46" - 61" 46" - 61" A9091-M48.0 62" - 79" 109" - 147" 62" - 79" 62" - 79" A9091-M60.0 A9091-M72.0 80" - 99" 100" - 147" — — 80" - 99" 100" - 147" 80" - 99" 100" - 147" * Supported Design NOTE: The dip tube must be cut to the required length (1⁄2" of container inside diameter minus 53⁄4"). Custom dip tube lengths available upon request. 3/4” Rotogages® for Small Stationary and Mobile LP-Gas Containers Rotogages® are designed to provide accurate determination of LP-Gas container contents. They may be end or side mounted in a standard 3⁄4" NPT coupling on stationary or mobile containers. To guarantee accurate measurement, they should not be used on stationary containers that exceed 60" I.D. or on mobile containers, subject to vibration, with an I.D. of more than 24". Dip Tube For Containers with Inside Diameter 2071-L25.7 Up to 40" 2071-L39.7 Up to 60" Part Number Rotogage 2070CO ® Tank Connection 34 ⁄ " M. NPT Valve Seat Orifice No. 54 Drill Size NOTE: The dip tube must be cut to the required length (1⁄2 of container inside diameter minus 1⁄2"), when mounted on center line of tank. 219 Gauge Dials — Junior & Senior Hermetically-sealed, moisture-proof, replaceable dial chambers are easily and safely removable under tank pressure. UV stabilized Jr. plastic case will not corrode. R3D Dials - Remote Ready Part # 5909S02733 5909S02799 5986S02733 5987S02787 5988S02788 Description Rochester Junior™ Dial / ASME Above ground Rochester Junior™ Dial / ASME Under ground Rochester Senior™ Dial / ASME Above ground JY Taylor Style A Dial JY Taylor Style B Dial 5909S02733 5986S02733 5987S02787 Junior™ Direct Read Dials for ASME Tanks Part # 5323S01749 5323S01813 5323S01848 Description Replaced by R3D Dial # 5909S02733 Junior™ Dial for LPG ASME Underground Tanks 5-95% Junior™ Dial for NH3 ASME Underground Tanks 5-95% Junior™ Direct Read Dials for Mobile 4-Bolt Gauges Part # 5323S01789 5323S01835 5323S01852 5343S01791 5323S01824 5323S01813 Description Junior™ Mobile Dial - Fractional Junior™ Dial 10-82% for Vertical Cylinders Junior™ Dial 5-88% for Vertical Cylinders Junior™ Universal Dial 33.5# Cylinders Junior™ Universal Dial 43# Cylinders 5323S01789 5323S01835 5323S01791 ™ Junior Direct Read Dials for 3/4” NPT Gauges Part # 5343S01992 5343S01993 5374S02445 5714S02591 Description Junior™ Universal Dial 33.5# Cylinders Junior™ Universal Dial 43# Cylinders ™ Junior Snap-On Dial 20 & 33.5# Duel Use Cylinders Junior™ Snap-On Dial for 7384-4021 5343S01992 5714S02591 ™ Junior Direct Read Dials for 1” NPT Gauges Part # 5364S01951 5364S02383 Description Junior™ Snap-On Dial for 8981 Series Gauges Junior™ Snap-On Dial for 8944 Series Gauges Senior™ Direct Read Dials Part # 5844S01749 5002S00002 5364S01951 Description Senior Dial for LPG - For Above ground use Senior™ Dial for NH3 - For Above ground use ™ 5844S01749 220 Gauge Dials — Other Universal Dial Kit Fits any LPG Float Gauge ever built. Complete instructions with each kit. Part # Description 3181-01749 Universal Dial Kit for Junior 3180-17001 Universal Dial Kit for Senior 3181-01848 NH3 Universal Dial Kit for Junior Advanced Matrix Film TwinSite™ The TwinSite™ is a magnetically-driven, variable-resistance sender with plotted lead wires. Senders are utilized on both mobile and stationary applications where direct reading plus an electrical signal to a remote receiver are required. Models are available to fit all Rochester Junior™, liquid-level gauges equipped with our large Alnico drive magnet. Par t # Description Resistance Range Part # Description Resistance Range P5628S02537 Junior™TwinSite™Sender (for GM) 0-90Ω P5752S02599 Junior™TwinSite™Sender (For GM) 40-250Ω P5630S02538 Junior™TwinSite™Sender (for Ford & Chrysler) 70-10Ω P5827S02649 Junior™TwinSite™Sender (For Dodge Trucks) 220-20Ω P5638S02542 Junior™TwinSite™Sender (For Ram Van) 105-10Ω P5799S02630 Junior™TwinSite™Sender Current Output 4-20ma P5663S02527 Junior™TwinSite™Sender (For Ford) 20-150Ω P5849S02269 Junior™TwinSite™Sender Voltage Divider 0-10Ω P5632S02539 Junior™TwinSite™Sender Switch 240-30Ω P5347S02040 Junior™TwinSite™Sender Switch 1/8 Tank — P5679S02560 Junior™TwinSite™Sender (For Ram Truck) 112-6Ω Magnetel ™ Replacement Dials Part # Description 5015S01403 8" Dial Chamber - Combo for LPG & NH3 - 3% to 97% 5015S00480 8" Dial Chamber - Any Liquid - 3% to 97% 5016S00445 4" Dial Chamber - Any Liquid - Rough Rider - 5% to 95% 5137S01262 4" Dial Chamber - Combo fo LPG & NH3 - Rough Rider - 5% to 95% 221 Gauge Accessories Magnetel ™ Mounting Flanges Tank-mounting flanges are not included with Magnetel™ Gauges and should be ordered separately. NOTE: Flanges welded to tank with top and bottom holes on the vertical centerline are standard with Rochester Gauges. When the flange is attached so that the bolt holes span the centerline (see drawing at the right), add the prefix “X” to the Magnetel™ gauge model number. Magnetel Mounting Part # Description "A" "B" "C" 0022-00029 Forged Steel 2 1/2" NPT Threaded Neck Flange 2 1/2" 0022-00030 Forged Steel Welding Flange Only — — — 0022-00500 Forged Steel Welding Flange Only 1 3/16" Weld 2 5/16" 0022-00525 2" NPT Sched 80 Threaded Neck Flange. (Must be installed on gauge by mfg. 2 1/2" 2" NPT 2 1/16" 1 2 2 5/16" / " NPT Straddle Bolt holes span center line Center Line Bolt holes on center line Senior Gauge Mounting 3 4 ⁄4" Part # Description "A" "B" "C" “A” 1" 0022-05210 Forged Steel Welding Flange Only 1" Weld 1 21/32" 0022-05211 Forged Steel Welding Flange Only 1" 2" NPT 1 21/32" Replacement Magnetel ™ Parts Part # Description 0003-00005 Glass crystal for 8" dial 0003-00408 Tempered glass crystal for 4" dial 0015-00010 Gasket under 8" crystal, two required 0015-00451 Channel gasket for 4" crystal 0015-00019 Mounting flange gasket—Spiral-wound stainless steel, Teflon filled 0040-00413 Stainless steel dial screw for 4" dial 0093S00001 4" Dial chamber mounting bracket 0093-00403 8" Dial chamber mounting bracket Magnetel Transmitter This transmitter is designed to fit Rochester model 6342 and 6360 Magnetel™ Float gauges with 8" dials. The transmitter provides a current output of 4-20 mA proportional to the liquid volume in a horizontal storage tank. Part # Description R6315-00012 4-20 ma Transmitter 222 “C” “B” Gauge Accessories Weather Guards For Dials Part # Description 0023S00001 Weather Cover For 8" Dial 0023S00002 Weather Guard For 4" Dial 0023S00003 Weather Guard For 8" Dial Weather Cover For 8" Dial Weather Guard for 4" Dial Weather Guard for 8" Dial Screws Part # Description 0040-00414 Screw for Junior Gauge Head— Combination Slotted or Phillips 0040-00415 Screw for Senior Gauge Head— Combination Slotted or Phillips 0040-00413 Screw for Senior Gauge Head— Stainless Steel for 4" Dial 0040-00416 Screw for JR & Senior Dial Mounting 0040-00478 Screw for Senior Gauge Head— N-Serv A6480 Series Gaskets, LP Gas Flat Buna N Part # Description 0015-00004 Senior gauge gasket 0015-00007 Junior gauge gasket 0015-00019 Spiralwound gasket, tef lon filled for SS head 0015-00022 Senior gauge O-ring 0015-00021 Junior gauge O-ring 223 Pressure Gauges Pressure Gauges Especially designed in a variety of sizes and construction for the LP Gas & anhydrous ammonia industry. Pressure Range Part Number Dial Size Case Material Connection Brass 1/4” M. NPT 2411 3226A-3 0-30# J1442 2” 1/4” Bottom J2042 2434-2 1/4” Back Steel 2434A-2 35” w.c. & 20 oz. (dual) 29276 0-35” w.c. 5575 J1446 1/4” hose 948 Brass 1/4” M. NPT Steel 1/4” Bottom Brass 1/4” M. NPT 0-60# 2” J1448 5576 0-100# 1178 2-1/2” J1458 948 J2058 1/8” hose 2-1/2” Steel 1/4” Bottom 2” 0-300# 1/4” M. NPT 1/4” Back Brass J5563 J1458 4-1/2” J1446 1/4” Bottom Liquid Filled Pressure Gauges Part Number Pressure Range 1008AL-300 0-300# Di al Size Case Material Connection 1 4 / " bottom Steel 1008AL-400 1008SB-400 2" 0-400# Stainless Steel 1008SSB-400 1 /4" back NH3 Pressure Gauges Part Number Pressure Range W0160 0-60# W0162 0-150# W0164 0-400# Di al Size Case Material Connection 1008AL-400 2 1/2" Stainless Steel 1 4 / " bottom W0164 ® Magnehelic Differential Pressure Gauge Magnehelic® gauge is highly accurate with a guarantee within 2% of full scale. Using simple, frictionless Magnehelic movement, it quickly indicates low air or non-corrosive gas pressures — either, negative (vacuum) or differential. The design resists shock, vibration and over-pressures. No manometer fluid to evaporate, freeze or cause toxic or leveling problems. Portable Unit Includes: Carrying case, Magnehelic Gauge, 9 ft fo 3/16” I.D. rubber tubing, standhang bracket and terminal tube with holder. Standard Accessories: Two 1/8” NPT plugs for duplicate pressure taps, two 1/8” pipe thread to rubber tubing adapter and three flush mounting adapters with screws. Part Pressure Number Range 2020 Accuracy 0 - 20” +/- 2% of Water of full scale Overpressure Temperature Limits Dial Size Case Material 25 psig 20 to 140° 4” Die Cast Aluminum Note: Do Not use with Hydrogen gas. Dangerous reactions will occur. 224 Mounting Connection Orientation Vertical 1/8” F. NPT Pressure Gauge Accessories Pressure Gauge Snubbers Protects pressure gauge from shocks and pulsations. Part # Description Size 1449 Stainless Steel 1/4” FNPT x 1/4” MNPT 1449 Rego Water Manometer Kit The water manometer kit is especially suited for use with low pressure LP-Gas systems. It is ideal for pressure checks downstream of the low pressure regulator and at the appliances. Part Number Description 1212 KIT Flexible Tube Water Manometer Kit Needle Valves These valves are high quality, “true’’ throttling valves. Unlike most so-called needle valves, both the body seat and stem are tapered to provide fine, precise control over a wide range of adjustment without stem galling. The 1224 may be used as a small, inexpensive shut-off valve between a pressure gauge and bulk storage container to allow for convenient gauge replacement. The 1314, 1316 and 1318 provide taper pipe thread by left hand hose connection threads and are useful in a wide range of torch and fuel burner applications where an accurate throttling action is required. Par t Number Inlet Connection 14 1224WA 1314WA 1316WA 1318WA Part # V-332 V-333 V-334 V-335 V-3055P V-880P ⁄ " M. NPT 9 16 ⁄ "-18 L.H. 14 ⁄ " M. NPT Inlet end 1/4" female pipe 1/4" 1/4" ⁄ " M. NPT ⁄ " M. NPT 1⁄4" M. NPT 9⁄16"-18 L.H. 18 1 9⁄16" 1 3⁄4" female pipe male pipe female pipe 1/4" male pipe female pipe Length Outlet end 1/4" 1/4" male pipe Height 14 male pipe 1/4" 1/4" Outle t Connection 1/4" female pipe 1/4" male pipe Squeeze valve w/ adjustable pilot 225 Thermometers & Flow Indicator LP & NH3 Bimetal Thermometers These 2", bimetallic thermometers are commonly used on LPGas & NH3 storage tanks, bobtails, and transports. They are recommended for use only with thermowells. The thermometer is made of type 304 stainless steel, and the crystal is made out of extra-heavy, curved glass. The aluminum dial has a white face with large black numbers for easy readability. Actuation is by means of a highly sensitive bimetal element, dampened to minimize vibration, attached to a pointer. The unit is hermetically sealed. Standard Features • 1⁄2" MNPT • Dual Scale Calibration: -90° to +130°F, -70C to +50C, other ranges available .08" Part # Description "A" Dimension 1750-00114 1750-00115 1750-9 1 ⁄2" NPT Pipe Thread 4" 6" 2" Bimetallic Thermometer 9" 1750-12 12" “A” Flow Indicator Indicates direction of flow of compatible liquids in pipelines at working pressures up to 600 psig up to 160°F. The indicator must be installed in pipeline tees. Specify Part Number and “A” Dimension Part # Length 6286-00325 3 1/4" 6286-00475 4 3/4" Other lengths available on special order. Tee Size “A” Dimension 1 1/4" x 1 1/4" x 1 1/4" 3 1/4" 2" x 2" x 2" 3 1/4" 2 1/2" x 2 1/2 " x 2" 3 1/4" 3" x 3" x 2" 4 3/4" 1 2 1 2 1 2 2 /" x2 /" x 2 /" w/ 2 1/2" x 2" bushing 4 3/4" 3" x 3" x 3" w/3" x 2" bushing 4 3/4" “A” Replacement Dial The distance from the top of the mounting adapter to the end of the vane is the “A” dimension. This dimension is dependent on the tee size, as shown above. 226 Part # 5013S00048 Tank Monitoring Equipment Streamline Distribution With Robertshaw Centeron™ Using non-intrusive, wireless tank-level monitors and advanced software, the Centeron™ system provides accurate, daily listings of tanks ready and near-ready for fills, making unnecessary trips and emergency fills an expensive thing of the past. Fact is, Centeron™ can cut your refill trips by up to 50 percent. These unprecedented cost efficiencies make the economical Centeron™ system an ideal, profit-building solution for both non-degreeday and degree-day sensitive operations. It’s the convenient, money-saving way to streamline your entire LPG distribution process. The Centeron™ transmitter is attached to the tank gauge and accurately measures tank levels and then sends the data to the Centeron™ controller (located inside the house) using robust DSSS wireless technology. The Centeron™ tank level monitor (TLM) includes sensing and FCC license-free RF telemetry capabilities. The sensor head screws on the existing float level gauge. Low cost installation and no maintenance. Centeron™ Tranmitter features: 1. Magnetically adheres to the tank 2. No field calibration 3. Applies to domestic and bulk storage tanks 4. Reports tank level and outside temperature 5. No hard wiring required, “wireless” The Centeron™ controller receives wireless signals from Centeron™ monitor and then sends the data to the district host center or to our secure data center for use in operations management. Centeron™ Controller features: 1. Uses DSSS broadband technology which is far superior to any other available 2. Easily attaches to any phone 3. Will not interrupt a conversation in progress 4. Can be remotely programmed for tank level thresholds, call windows and telephone numbers. 5. Unique phase and diverse antenna arrangement eliminates noise, fading, and signal blocking commonly found when using narrow band technology The data center operates with a “Call Block” plan. This plan will allow all of your controllers to collectively draw from one block of prepaid calls. A wide variety of Call Blocks will be offered in order to satisfy all Centeron customers. Inherent benefits of this plan include: • One simple invoice for all of your data center fees • Current data for Call Block usage available online • Multiple controllers collectively draw from the same Call Block • Reduction in price you pay per call • Refunds available for unused calls upon cancellation of service For Domestic applications Select: 1. Transmitter & specify signal intervals. 2. Controller with or without Temperature sensor. 3. Appropiate type of domestic gauge dial(s). For Bulk Plant applications Select: 1. Transmitter & specify signal intervals. 2. Controller without Temperature sensor and for appropiate number of tanks (inputs). 3. Appropiate type of bulk storage gauge dial(s). Consumer Monitor Package Part # TM-RS-228 Description Pkg. includes: Base Station, Remote Monitor (Dial NOT included) Domestic Tank Monitoring Package Part # TM-RES-R TM-RES-T Description Pkg. includes: TM-GM60, TM-TC1NT, 5909S02733 Pkg. includes: TM-GM60, TM-TC1NT, 5987S02787 TM-RS-228 Transmitters (includes 5 ft. cable) Part # TM-GM60 TM-GM120 TM-GM240 Intervals in Minutes 60 120 240 TM-GM60 Controller/Receiver Part # TM-TC1T TM-TC1NT TM-TC4NT TM-TC20NT Temperature Sensor Yes No No No Inputs 1:1 1:1 4:1 20:1 Gauge Dials TM-TC1NT Domestic Part # 5909S02733 5986S02733 5987S02787 5988S02788 Description Rochester R3D JR Dial Rochester R3D SR Dial JY Taylor R3D Style A Dial JY Taylor R3D Style B Dial Bulk Storage Part # TM-MG8-10 TM-JY10-10 Description Rochester Gauge with 10 ft. cable J Y Taylor Dial with 10 ft. cable 5909S02733 5323S02787/88 Accessories Part # TM-PC CABLE TM-GMCABLE-5R Description Serial interface cable- Controller to PC RS232 port Additional 5 ft. cable for AG/UG GM monitors available 227 228