RSR Series Aluminum Cord Grips
AAAAAAAA
Straight Body, External Cord Thread
Complete Assembly
Catalog Numbers
Conduit
Size
RSR Series Grips are used in conduit hubs or knock-outs at
1"
the point where the electrical cable is to be terminated. They
4
are used in indoor as well as outdoor applications to prevent
cable pullout, control cable arc of bend, and provide an
environmental seal against dirt, moisture, coolants, corrosive
3"
8
fumes, etc. The seal is accomplished when the tapered rubber
bushing (Neoprene) is driven into a tapered seat in the grip
body by tightening the nut. An anti-friction washer is
supplied between the nut and bushing for ease in
1"
2
compression. Remke's rugged cord grips protect cable from
damage. They are offered in machined aluminum, steel,
stainless steel, and nylon fittings. These fittings are also
offered in a variety of configurations as well as N.P.T. and
1"
2
PG metric thread sizes.
1"
2 .
3"
4
3"
4
CERTIFICATION AND COMPLIANCES:
UL Standard: 5 1 4
File #553599
CSA Standard C22.2 # 1 8
File #28985
National Electrical Code
Articles 400-10 and 400-14
NEMA Standards FBI-1983
Hazardous Locations:
NEC Sec. 501 -4(b]
502-4(a](2), and 503-3(a).
For Class I, Div.2; Class II, Div. 1 and 2; and Class III, Div. 1 and 2.
See page 1 2 for additional Product Data.
3"
4
Cable Range
.125.188.250.312.375.125.188.250.312.375.125.188.250.312.375.125.188.250.312.375.438.500.562.438.438.500.562.625.688.125.188.250.312.375.438.500.562.438.438.500.562.625.688.438.500.562.625.688.750.812.875-1
.188
.250
.312
.375
.438
.188
.250
.312
.375
.438
.188
.250
.312
.375
.438
.188
.250
.312
.375
.438
.500
.562
.625
.500
.562
.625
.688
.750
.812
.188
.250
.312
.375
.438
.500
.562
.625
.500
.562
.625
.688
.750
. 8 1 2.562
.625
.688
.750
.812
.875
.938
.000
Cord Grip
Only
RSR-0003
RSR-0004
RSR-0005
RSR-0006
RSR-0007*
RSR-003
RSR-004
RSR-005
RSR-006
RSR-007*
RSR-1003
RSR- 1004
RSR- 1005
RSR- 1006
RSR- 1007
RSR-103
RSR- 104
RSR- 105
RSR- 106
RSR- 107
RSR-108
RSR-109
RSR-110
RSR-1208
RSR-1209
RSR-1210
RSR-1211*
RSR-1212*
RSR-1213*
RSR-2103
RSR-2104
RSR-2105
RSR-2106
RSR-2107
RSR-2108
RSR-2109
RSR-2110
RSR-208
RSR-209
RSR-210
RSR-211
RSR-2 1 2
RSR-2 1 3
RSR-2309
RSR-2310
RSR-23 1 1
RSR-23 1 2
RSR-23 1 3
RSR-23 1 4 *
RSR-23 1 5 *
RSR-23 16*
Cord Grip
With Mesh
RSR-0004-E
RSR-0005-E
RSR-0006-E
RSR-0007-E
RSR-004-E
RSR-005-E
RSR-006-E
RSR-007-E
RSR-1004-E
RSR-1005-E
RSR-1006-E
RSR-1007-E
RSR-104-E
RSR-105-E
RSR-106-E
RSR-107-E
RSR-108-E
RSR-109-E
RSR-110-E
RSR-1 208-E
RSR-1 209-E
RSR-1210-E
RSR-1211-E
RSR-1212-E
RSR-1213-E
RSR-2 104-E
RSR-2 1 05-E
RSR-2 1 06-E
RSR-2 107-E
RSR-2 108-E
RSR-2 109-E
RSR-2 1 1 0-E
RSR-208-E
RSR-209-E
RSR-2 1 0-E
RSR-2 1 1 - E
RSR-2 12-E
RSR-2 13-E
RSR-2309-E
RSR-2 31 0-E
RSR-23 1 1 - E
RSR-23 12-E
RSR-23 13-E
RSR-23 14-E
RSR-23 15-E
RSR-23 16-E
RSR Series Aluminum
Complete Assembly
Catalog Numbers
45° Cord Grips
Conduit
Size
AAAAAAAA
45° Body, External Conduit Thread
1"
The cord grip assemblies on this page are the same as the
2
RSR cord grips listed previously except for the body, which
instead of being straight is 45 degree. The descriptive
information for RSR cord grips is applicable.
3"
4
1"
RSR 45° Cord Grips Only Dimension Table
Catalog
Number*
RSR-45100-W
RSR-45200-W
RSR-45300-W
RSR-45400-W
RSR-45500-W
Conduit
Size
V,"
%"
1"
1 1
i /;
1/2"
A
B
C
D
Body
Bore
.58
.76
E
Body
Hex.
.56
.99
1.28
.63
.63
.69
1.40
.69
1.19
1.44
1.31
1.69
1.69
1.19
1.53
1.88
1.00
1.25
1.44
1.88
1.88
2.50
1.88
F
Nut
Dia.
Form
Size
1.33
2
3
1.52
1.70
2.55
2.55
4
5
5
I1 1 "
4
I1 1 "
2
Cable Range
.125- . 1 8 8
. 1 8 8 - .250
.250- . 3 1 2
.312- .375
.375- .438
.438- .500
.500- .562
.562- .625
.438- .500
.438- .562
.500- .625
.562- .688
.625- .750
.688- . 8 1 2
.438- .562
.500- .625
.562- .688
.625- .750
.688- . 8 1 2
.750- .875
.812- .938
.875-1.000
.562- .688
.688- . 8 1 2
.750- .875
.875-1.000
1.000-1.125
1.125-1.250
1.250-1.375
.562- .688
.688- . 8 1 2
.750- .875
.875-1.000
1.000-1.125
1.125-1.250
1.250-1.375
Cord Grip
Only
RSR-45 1 03
RSR-45 1 04
RSR-45 1 05
RSR-45 106
RSR-45 107
RSR-45 1 08
RSR-45 1 09
RSR-45 1 1 0
RSR-45208
RSR-45209
RSR-45210
RSR-45211
RSR-45212
RSR-45213
RSR-45309
RSR-45310
RSR-45311
RSR-453 1 2
RSR-453 1 3
RSR-453 1 4
RSR-453 1 5
RSR-453 1 6
RSR-45411
RSR-45413
RSR-45414
RSR-45416
RSR-45418
RSR-45420
RSR-45422
RSR-45511
RSR-45513
RSR-45514
RSR-45516
RSR-45518
RSR-45520
RSR-45522
Cord Grip
With Mesh
RSR-45 104-E
RSR-45 1 05-E
RSR-45 1 06-E
RSR-45 107-E
RSR-45 108-E
RSR-45 109-E
RSR-45 1 1 0-E
RSR-45208-E
RSR-45209-E
RSR-45210-E
RSR-45211-E
RSR-452 1 2-E
RSR-452 1 3-E
RSR-45309-E
RSR-453 1 0-E
RSR-453 11 -E
RSR-453 1 2-E
RSR-453 1 3-E
RSR-453 1 4-E
RSR-453 15-E
RSR-453 16-E
RSR-45416-E
RSR-45418-E
RSR-45420-E
RSR-45422-E
RSR-45516-E
RSR-45518-E
RSR-45520-E
RSR-45522-E
*See also notes on Dimension Table for RSR cord grips.
Dimension E is across flats.
RSR SERIES PRODUCT DATA
National Electrical Code
Articles 400-10 and 400-14
Fed. Spec. W-C 586
Mil. Spec. 100 and 1 3 0
Features:
- Large Range of NPT and PG
metric sizes for use with any
conduit system.
- Rugged design protects cable
from damage.
- Available for straight, 45 deg. or
90 deg. entrance.
- Alternate bushing materials for
special cable jackets available.
Standard Materials:
- RSR-Series - Machined aluminum
- RSP-Series - Nylon
- RSRS-Series - Steel
- RSSS-Series - 303/304 Stain ess
Steel
- RPG Series - Machined aluminum
Size Ranges:
Cable O.D. - . 1 25 to 2.438
NPT Thread- 1 / 4 " to 3"
PG Metric - PG 1 1 to PG 48
R
E
M
K
E
D
bending of the cable. They are used primarily where flexible
cable connects electrical equipment to bus duct. They are also
used to support or restrain air hose and water hose.
Double Bus Drop Grips store excess cable neatly.
Bus Drop Grips with Safety Springs and Strain Relief
Grips can provide a complete flexible cord system which
adapts to any layout. The Strain Relief Grips relieve the strain
on the terminals. The Bus Drop Grips provide positive
permanent support which, unlike rigid conduit systems, can
be adjusted instantly if equipment is repositioned. Almost any
system can be installed quickly even in cases where
equipment and bus duct are distantly located or awkwardly
positioned.
Safety Spring -
E
L
V
E
R
S
approximate breaking strength listed in the catalog.
CAUTION: The broad application of Remke grips requires
adequate safety factors be used to establish a SAFE working
load. Refer to specific catalog pages for more information.
Single Eye Grips employ a single eye for each attachment to
open hooks or other open end structural members. The
formed eye tube assures long, trouble-free resistance to wear.
Can be used with SAFETY SPRINGS.
Universal Bail Grips employ a flexible "universal" bail eye
for each attachment around closed-end structures such as
pipe, columns or through closed eyes. The universal bail is a
secure, self-locking attachment and is reusable. Removal is
simple and quick. Can be used with SAFETY SPRINGS.
Safety Springs can be used with either SINGLE EYE or
UNIVERSAL BAIL GRIPS to relieve sudden tensions
exerted on cable system. When used with single eye grip,
disassemble drawbar from coil, placing drawbar through eye
of grip, then replace drawbar.
Liqua-Seal Mesh Connectors
Strain Relief Grips
Typical Bus Drop &
Strain Relief System
Liqua-Seal Mesh Connectors prevent pullout and provide
strain relief when connecting liquid-tight flexible metal
conduit to electrical enclosures.
Motor
Box
Material
The standard mesh material is galvanized steel which has
high tensile strength and corrosion resistance (more than
adequate for most indoor applications).
Optional stainless steel grips are available.
All Bus Drop Grips are "Wide Range" (to accept more cable
per size) with strand equalizers which uniformly distribute
compressive force over a large area of the cable for maximum
gripping strength with minimum concentration of force
without pinching the cable.
Features/Benefits
• Few Grips are needed to fit many cable sizes.
• Readily installed, adjusted, repositioned, removed or reused which saves time and money when relocating plant
wiring or machines.
• Easily attached to both open and closed end structures.
• Automatically adjust their gripping to hold the required
load.
• No special installer skill or special tools required.
• Increases safety to personnel working in the application
area.
Working Load/Safety Factor
This is an abbreviated version of the more detailed
information on catalog page 28. The approximate breaking
strength of the Remke grip represents an average calculation
based on test factors which have been determined in our
engineering labs using NEW grips and metal rods. As a rule
of thumb the working load may be considered 1/10 of the
Material
The standard mesh design is single weave, corrosion free
stainless steel, these mesh grips are available with fittings
made of steel (3/g"-l" straight connectors) or ductile iron (1l/4"-2" straight connectors and all 45° and 90° connectors),
with or without insulated throat.
Features/Benefits
• The mesh exerts a uniformly distributed compressive force
over a large area of the conduit for maximum gripping
without pinching the conduit.
• An endless weave conforms to the conduit, eliminating
wedging or crushing of the conduit at that point.
• Mesh material has high tensile strength and corrosion
resistance.
• Readily installed, adjusted, repositioned, removed or reused.
• Automatically adjust their gripping to hold the required
load.
• No special installer skills or special tools required.
Working Load/Safety Factor
(see Wide Range Strain Relief Grips)
Standard Strain Relief Connector Grips
Standard Strain Relief Connector Grips are used in
conduit hubs or knock-outs at the point where the portable
electrical cable is to be terminated. The provide an
environmental seal against dirt, moisture, coolants, corrosive
fumes, etc. and provide strain relief where undue strain on
the cable would otherwise cause loosening or pull-out at the
individual wire terminals. Primary applications are in the
wiring of portable power tools, power centers and bus drop
cable systems.
Material
The Standard mesh design is multi-weave corrosion free
stainless steel, these mesh grips are available with fittings
made of aluminum in straight, 45° or 90° body design; also
with fittings made of steel, stainless steel or nylon in straight
body design. All these fittings come with neoprene bushings.
Features/Benefits
• The mesh exerts a uniformly distributed compressive force
over a large area of the cable for maximum gripping without
pinching the cable.
• An endless weave conforms to the cable jacket, eliminating
wedging or crushing of the cable at that point.
• Mesh material has high tensile strength and corrosion
resistance.
• Readily installed, adjusted, repositioned, removed or reused.
• Automatically adjust their gripping to hold the required
load.
• No special installer skills or special tools required.
Working Load/Safety Factor
(see Wide Range Strain Relief Grips.)
• SR series has a male N.P.T. tapered thread and locknut for
the l/2"-2-l/2" thread size. This allows easy attachment to
enclosures up to 3/8" thick. An insulated bushing is provided
to prevent metal to conductor contact.
• Adjusts to wide range of cable or cord diameters, so fewer
grips are needed to fit many cable sizes.
• Readily installed, adjusted, repositioned, removed or reused.
Makes relocating plant wiring and machines easy.
• Automatically adjust their gripping to hold the required
load.
• No special installer skills or special tools required.
Working Load/Safety Factor
This is abbreviated version of the more detailed information
on catalog page 28. The approximate breaking strength of a
Remke grip (as shown in the catalog) represents an average
calculation based on test factors which have been determined
in our engineering labs using NEW grips and metal rods. As a
rule of thumb the working load may be considered 1/10 of the
approximate breaking strength listed in the catalog.
CAUTION: The broad application of Remke grips requires
adequate safety factors be used to establish a SAFE working
load. Refer to specific catalog pages for more information.
Wide Range Strain Relief Grips
Wide Range Strain Relief Grips connect flexible cord or bus
drop cable to electrical enclosures and equipment. Designed
primarily to prevent pull tension on cable to be transmitted to
the joints or terminals. The National Electrical Code requires
terminal tension protection. Easily installed. Primary
applications are indoors in the wiring of electrical enclosures,
such as power boxes, cabinets, panel boards, machine tools,
portable power tools, power centers and bus drop cable
systems.
They can be used with Bus Drop Grips and Safety Springs to
provide a complete flexible cord system that adapts to any
layout.
Factory Assistance
Material
The standard mesh design is wide range mesh single weave,
made of galvanized steel. Gasket seals are made of P.V.C.
Available with insulated or non-insulated fittings made of
aluminum.
When factory assistance is required for specific
applications, etc., please be prepared to provide
all pertinent information:
Features/Benefits
• The mesh exerts a uniformly distributed compressive force
over a large area of the cable for maximum gripping without
pinching the cable.
• An endless weave conforms to the cable jacket, eliminating
wedging or crushing of the cable at that point.
• Mesh material has high tensile strength and corrosion
resistance (more than adequate for most indoor
applications).
• P.V.C. gasket seals out large dust particles, lint or metal
filings and other contaminants from the electrical
connections.
2. Material of object to be gripped
1 . Object to be gripped
3. Environment (temperature, abrasion corrosion)
4. Diameter range
5. Eye length
6. Mesh length
7. Mesh material
8. Length of support
9. Other special conditions
R
E
M
K
D
E
E
L
I
V
E
R
S
Flexible Electrical Cord or Cable
to Cord Grip Selection Table
AAAAAAAA
Type Cord
SJ-SJTO
SJO
—
18/2
18/2
18/3
18/3
18/4
18/4
16/2
16/2
16/3
16/3
16/4
16/4
14/2
14/2
14/3
14/3
14/4
14/4
Cord
OD
.125-.188
.125-.188
.188-.250
.188-.250
Hub
Size
/i 'i
'/, "
.290
.290
.320
.320
.335
.335
.320
.320
.340
.340
.385
.385
.350
.350
.375
.375
.415
i .415
'/? "
'/• "
y="
'/:"
y."
A"
i"
y,"
y,"
y<"
'/•."
'/<"
Straight
Cord Grip
Number
RSR-1003
RSR-2103
RSR-1004
RSR-2104
Alternate
Straight
Number
RSR-103
90°
Cord Grip
Number
RSR-9103
45°
Cord Grip
Number
RSR-45103
RSR-104
RSR-9104
RSR-45104
RSR-1005
RSR-2105
RSR-1006
RSR-2106
RSR-1006
RSR-2106
RSR-1006
RSR-2106
RSR-1006
RSR-2106
RSR-1007
RSR-2107
RSR-1006
RSR-2106
RSR-1007
RSR-2107
RSR-1007
RSR-2107
RSR-105
RSR-9105
RSR-45105
RSR-106
RSR-9106
RSR-45106
RSR-106
RSR-9106
RSR-45106
RSR-106
RSR-9106
RSR-45106
RSR-106
RSR-9106
RSR-45106
RSR-107
RSR-9107
RSR-45107
RSR-106
RSR-9106
RSR-45106
RSR-107
RSR-9107
RSR-45107
RSR-107
RSR-9107
RSR-45107
RSR-1006
RSR-2106
RSR-1006
RSR-2106
RSR-1007
RSR-2107
RSR-106
RSR-9106
RSR-45106
RSR-106
RSR-9106
RSR-45106
RSR-107
RSR-9107
RSR-45107
RSR-1006
RSR-2106
RSR-1007
RSR-2107
RSR-107
RSR-2107
RSR-109
RSR-2109
RSR-309
RSR-109
RSR-2109
RSR-209
RSR-309
RSR-110
RSR-2110
RSR-310
RSR-110
RSR-2110
RSR-310
RSR-110
RSR-106
Type Cord
S-SO
STO
18/2
18/2
18/3
18/3
18/4
18/4
.345
16/2
16/2
16/3
16/3
16/4
16/4
14/2
14/2
14/2
14/3
14/3
14/3
14/3
14/4
.370
.370
.390
14/4
14/4
12/2
12/2
12/2
12/3
.345
.365
.365
.390
.390
.390
.415
.415
.500
.500
.500
.530
.530
.530
.530
.570
.570
.570
.575
.575
.575
.600
'/;"
y."
'/.•"
y«"
'/;"
y<°
'/."
%"
y
'%"
y,"
y."
i/r
y<"
i"
'/;"
y'
i"
/;"
y."
1"
'//"
•/="
1"
'/i"
RSR-107
RSR-1207
RSR-1209
RSR-209
RSR-1209
RSR-209
RSR-310
RSR-1211
RSR-211
RSR-311
RSR-1210
RSR-210
RSR-1210
RSR-9106
RSR-9107
RSR-9107
RSR-9109
RSR-9209
RSR-9309
RSR-9109
RSR-9209
RSR-9210
RSR-9309
RSR-9110
RSR-9210
RSR-9310
RSR-9110
RSR-9210
RSR-9310
RSR-9110
RSR-45106
RSR-45107
RSR-45107
RSR-45109
RSR-45209
RSR-45309
RSR-45109
RSR-45209
RSR-45210
RSR-45309
RSR-45110
RSR-45210
RSR-45310
RSR-45110
RSR-45210
RSR-45310
RSR-45110
type Cord
S-STO
SO
12/3
12/3
12/4
12/4
12/4
10/2
10/2
10/2
10/3
10/3
10/3
10/4
10/4
10/4
8/2
8/2
8/2
8/3
8/3
8/3
8/4
8/4
8/4
8/4
8/4
Cord
OD
Hub
Size
.600
.600
''k
1"
.650
.650
.650
.625
.625
.625
.660
.660
.660
'/;"
y<"
1"
.710
.710
.710
.675
.675
.675
.725
.725
.725
.780
y?"
.780
.780
.780
.780
6/2
6/2
6/2
6/3
6/3
6/3
6/4
.795
.795
.795
.865
6/4
6/4
4/3
4/3
4/3
4/4
4/4
4/4
2/3
2/3
2/3
2/4
2/4
2/4
.900
.900
y,"
i"
r/<"
v/,"
i"
i1/."
v/i"
i"
r/411
i'/i"
i"11
.865
.865
.900
'/;"
y<;
'/!"
y."
i"
1"
'/,"
y<"
i"
'/*"
y,"
i"
i/;
I!/,"
.975
.975
1"
I1/."
.975
I'/!"
1.100
1.100
1.100
1.170
1.170
1.170
1.290
1.290
1.290
1"
I'/."
Vh"
1"
l'/i"
r/2"
V
Vh"
Vh"
Straight
Cord Grip
Number
RSR-2110
RSR-310
RSR-1211
RSR-211
RSR-311
RSR-1211
RSR-211
RSR-311
RSR-1211
RSR-211
RSR-311
RSR-1212
RSR-212
RSR-312
RSR-1211
RSR-211
RSR-311
RSR-1212
RSR-212
RSR-312
RSR-1213
RSR-213
RSR-313
RSR-414
RSR-514
Alternate
Straight
Number
RSR-210
RSR-310
90°
Cord Grip
Number
RSR-9210
RSR-9310
45°
Cord Grip
Number
RSR-45210
RSR-45310
RSR-2311
RSR-9211
RSR-9311
RSR-45211
RSR-45311
RSR-2311
RSR-9211
RSR-9311
RSR-45211
RSR-45311
RSR-2311
RSR-9211
RSR-931 1
RSR-4521 1
RSR-45311
RSR-2312
RSR-9212
RSR-931 2
RSR-4521 2
RSR-45312
RSR-2311
RSR-9211
RSR-9311
RSR-45211
RSR-45311
RSR-2312
RSR-9212
RSR-931 2
RSR-4521 2
RSR-45312
RSR-2313
RSR-3514
RSR-9213
RSR-931 3
RSR-9414
RSR-9514
RSR-4521 3
RSR-45313
RSR-45414
RSR-45514
RSR-313
RSR-414
RSR-514
RSR-314
RSR-414
RSR-514
RSR-315
RSR-416
RSR-516
RSR-3516
RSR-416
RSR-516
RSR-3518
RSR-418
RSR-518
RSR-3520
RSR-420
RSR-520
RSR-3522
RSR-422
RSR-522
RSR-3514
RSR-931 3
RSR-9414
RSR-9514
RSR-931 4
RSR-9414
RSR-9514
RSR-931 5
RSR-9416
RSR-9516
RSR-45313
RSR-45414
RSR-45514
RSR-45314
RSR-45414
RSR-45514
RSR-45315
RSR-45416
RSR-45516
RSR-9416
RSR-9516
RSR-45416
RSR-45516
RSR-9418
RSR-9518
RSR-45418
RSR-45518
RSR-9420
RSR-9520
RSR-45420
RSR-45520
RSR-9422
RSR-9522
RSR-45422
RSR-45522
RSR-3514
RSR-3516
If a Mesh Grip is required, add letter "E' to end of Remke part number. This
chart is based on the cable diameters shown. The actual diameter of the
cable being used may require the next larger or smaller cord grip bushing.
Cable diameters vary between manufacturers and because cable manufacturers must allow tolerance, their published data should be checked.
Note: The bushinq I.D. should be larqer than, but as close as possible to,
the cable O.D.
R
E
M
K
E
D
E
L
I
V
E
R
S
RSR Straight Cord Grips
Cross Reference (continued)
AAAAAAAA
With Mesh Grip
1"
2
3"
4
1"
U"
1?
2"
1 "
2-
Z
2
3"
Cable
Range
.250- .3 12
.31 2- .375
.375- .438
.438- .500
.500- .625
.562- .688
.625- .750
.250- .3 12
.3 12- .375
.375- .438
.438- .500
.438- .562
.500- .625
.562- .688
.625- .750
.750- .875
.81 2- .938
.438- .562
.500- .625
.562- .688
.625- .750
.688- .81 2
.750- .875
.81 2- .938
.875-1.000
.875-1.000
1.000-1.125
1.125-1.250
1.250-1.375
.875-1.000
1.000-1.125
1.125-1.250
1.250-1.375
1.438-1.562
1.562-1.688
1.688-1.812
1.812-1.938
1.938-2.062
2.062-2.188
2.188-2.312
2.312-2.438
1.688-1.812
1.812-1.938
1 .938-2.062
2.062-2.188
2.188-2.312
2.312-2.438
1.688-1.812
1.812-1.938
1.938-2.062
2.062-2.188
2.188-2.312
2.312-2.438
Remke
RSR-105-E
RSR-106-E
RSR-107-E
RSR-108-E
RSR-110-E
RSR-1211-E
RSR-1212-E
RSR-2105-E
RSR-2106-E
RSR-2107-E
RSR-2108-E
RSR-209-E
RSR-210-E
RSR-211-E
RSR-212-E
RSR-2314-E
RSR-2315-E
RSR-309-E
RSR-310-E
RSR-311-E
RSR-312-E
RSR-313-E
RSR-314-E
RSR-315-E
RSR-316-E
RSR-416-E
RSR-418-E
RSR-420-E
RSR-422-E
RSR-516-E
RSR-518-E
RSR-520-E
RSR-522-E
RSR-625-E
RSR-627-E
RSR-6729-E
RSR-6731-E
RSR-6733-E
RSR-6735-E
RSR-6737-E
RSR-6739-E
RSR-729-E
RSR-731-E
RSR-733-E
RSR-735-E
RSR-737-E
RSR-739-E
RSR-8729-E
RSR-8731-E
RSR-8733-E
RSR-8735-E
RSR-8737-E
RSR-8739-E
(Bryant)
Economy
DCG25-/2 "
DCG25-/; "
DCG37-/2 1 '
DCG37-/2 "
DCG50-/2 11
DCG50-/2 "
Pass & Seymour
Slater/Flexcor
CG-405
CG-406
CG-407
CG-408
CG-410
CG-409
DCG25-3//
DCG25-3//
DCG37-3//
DCG37-%"
DCG50-3//
DCG50-%"
DCG62-%"
DCG62-%"
CG-606
CG-606
CG-607
CG-607
CG-609
CG-610
CG-611
CG-612
DCG50-1"
DCG50-1"
DCG62-1"
DCG75-1"
DCG75-1 "
DCG87-1"
DCG87-1 "
DCG87-1 V,"
DCG100-1W
DCG112-T/4"
DCG125-1 1 //
DCG87-1 /:"
DCG100-r/2"
DCG112-l'/2"
DCG125-r/2"
DCG 137-2"
DCG 150-2"
CG-809
CG-809
CG-811
CG-813
CG-814
CG-815
CG-816
CG-1016
CG-1018
CG-1020
CG-1022
CG-1218
CG-1220
CG-1222
—
—
—
;
1
(Hubbell)
Kellems
074-01-006
074-01-006
074-01-008
074-01-008
074-01-010
074-01-010
074-01-1247
074-01-013
074-01-013
074-01-015
074-01-015
074-01-017
074-01-017
074-01-018
074-01-018
074-01-1249
074-01-019
074-01-019
074-01-021
074-01-021
074-01-023
074-01-025
074-01-025
074-01-026
074-01-027
074-01-028
074-01-1178
074-01-029
074-01-030
074-01-031
074-01-032
074-01-033
074-01-034
074-01-035
074-01-1262
074-01-1262
074-01-1263
074-01-1264
074-01-1265
074-01-1030
074-01-1031
074-01-1032
074-01-1033
074-01-1034
074-01-1266
074-01-1036
074-01-1037
074-01-1038
074-01-1039
Woodhead
36251
36252
36253
36254
36256
36256
36257
36257
36259
36259
36260
36261
36262
36263
36275
36275
36265
36266
36267
36268
36269
36271
36272
36273
36274
36475
36476
36477
36478
36485
36486
36487
36489
36816
36287
36288
36289
36800
36801
36802
36803
36804
36805
36806
36807
36808
36809
36810
36811
PyleNational
DBKM-1205
DBKM-1206
DBKM-1207
DBKM-1208
DBKM-1210
DBKM-1311
DBKM-1312
DBKM-2205
DBKM-2206
DBKM-2207
DBKM-2208
DBKM-2209
DBKM-2210
DBKM-2311
DBKM-2312
DBKM-2514
DBKM-2516
DBKM-3308
DBKM-33 1 0
DBKM-33 1 1
DBKM-33 12
DBKM-3513
DBKM-3514
DBKM-3515
DBKM-3516
DBKM-4716-K
DBKM-4718-K
DBKM-4720-K
DBKM-4722-K
DBKM-5716-K
DBKM-5718-K
DBKM-5720-K
DBKM-5722-K
DBKM-6824-K
DBKM-6826-K
DBKM-7932-K
DBKM-7932-K
DBKM-7934-K
DBKM-7931-K
—