Analog input modules 4 inputs, voltage S20-AI-4-U 2 Bosch Rexroth AG | Electric Drives and Controls Analog input modules 4 inputs, voltage n S20-AI-4-U Documentation •Data sheet •4 analog bipolar input channels for connection of voltage signals •Application description •Voltage ranges: 0 ... 10 V, ±10 V, 0 ... 5 V, ±5 V •Input filter switchable •Measured value display 16 bit •Electronic device nameplate •Diagnostic and status indicators The module is designed for use within an IndraControl S20 station. It is used to acquire analog voltage signals. The connection is made in 2-, 3- and 4-wire technology plus a shield connection. Technical data S20-AI-4-U Local bus interface Designation Number of participants per station S20 local bus Connection for bus socket module Supply for module electronics Supply voltage Logic voltage UBUS Current consumption of UBUS Protective circuit 24 V DC 5 V DC (via bus socket module) Max. 150 mA Overvoltage protection, reverse polarity protection, transient protection Analog inputs Connection technology of the sensors Number Input voltage range Input resistance voltage Connection type Connection data solid / flexible / AWG Supply analog module UA 2-, 3-, 4-wire connection (shielded) 4 (differential inputs, current) 0 ... 5 V, -5 ... 5 V, 0 ... 10 V, -10 ... 10 V 268 kW (typical) Spring-cage connection with direct plug technology 0,2 ... 1,5 mm2 / 0,2 ... 1,5 mm2 / 24-16 24 V DC Characteristics Measurement resolution 16 bits (15 + sign bit) Input filter 30 Hz, 12 kHz and averaging (configurable) Accuracy 0.1% (of measurement range end value with active averaging and 30 Hz filter) System times System bus cycle time 2 µs Offset per module 1 µs Load Vibration resistance 5 g according to EN 60068-2-6 Electric Drives and Controls, PDF version, as of # date #, © Bosch Rexroth AG, subject to change Electric Drives and Controls | Bosch Rexroth AG Analog input modules 4 inputs, voltage n S20-AI-4-U Shock resistance 25 g according to EN 60068-2-27 Shock resistance (continuous shock) according to EN 60068-2-29 Emitted interference 10 g according to EN 60068-2-29 Class B according to EN 61000-6-3 Interference immunity According to EN 61000-4 Environmental conditions Permissible temperature (operation) -25 °C ... +60 °C Permissible humidity (operation) 5 to 95%, no dewing Permissible humidity (storage) 5 to 95%, no dewing Protection category IP20 Dimensions 126,1 54 122,4 35 S20-AI-4-U Dimensions Height H [mm] 126.1 Width B [mm] 35 Length T [mm] 54 Ordering information Type code Description Material number: S20-AI-4-U IndraControl S20 analog input module - 4 current inputs, complete with accessories (bus base module) R911173256 Electric Drives and Controls, PDF version, as of # date #, © Bosch Rexroth AG, subject to change 3 4 Bosch Rexroth AG | Electric Drives and Controls Analog input modules 4 inputs, voltage n S20-AI-4-U Type code Description Material number: S20-BS-S Bus base module (spare part) R911173203 Type code Description Material number: S20-SHIELD SET Shield connection kit R911173030 S20-SHIELD-NLS Neutral busbar 3 mm x 10 mm, length: 1000 mm R911173283 S20-SHIELD-SK14 Shielding terminal 14 mm for shield on busbars, contact resistance < 1 mOhm, VPE: 10 pieces Shielding terminal 5 mm for shield on busbars, contact resistance < 1 mOhm, VPE: 10 pieces R911173286 S20-SHIELD-SK5 Electric Drives and Controls, PDF version, as of # date #, © Bosch Rexroth AG, subject to change R911173282 Bosch Rexroth AG Postfach 13 57 97803 Lohr, Germany Bgm.-Dr.-Nebel-Str. 2 97816 Lohr, Germany Tel. +49 9352 18-0 Fax +49 9352 18-8400 www.boschrexroth.com/electrics Local contact information can be found at: www.boschrexroth.com/adressen © Bosch Rexroth AG 2012 Subject to modification. Printed in Germany The data specified above only serve to describe the product. As our products are constantly being further developed, no statements concerning a certain condition or suitability for a certain application can be derived from our information. The information given does not release the user from the obligation of own judgment and verification. It must be remembered that our products are subject to a natural process of wear and aging.