MITEQ IF Signal Processing Components
Logarithmic Amplifiers
Detector Log Video Amplifiers
Successive Detection IF LOG Amps
Frequency Discriminators
Constant Phase Limiting Amps
Custom Specification IF Parts
The MLS series is the newest addition to MITEQ’s line of high-performance
logarithmic amplifiers. Utilizing the lastest MIC (microwave integrated circuit)
technology, these logarithmic amplifiers achieve exceptional performance in
packages as small as 1.8 square inches.The design uses low-noise gain blocks and
the same proprietary detection circuitry as the MLIF series to achieve ultrawide
operational bandwidths. Increased sensitivity and video rise times as fast as 1.5 ns are
available.
OPERATIONAL
FREQUENCY
RANGE
MODEL
NUMBER
MLS-375/250-70
MLS-550/500-70
MLS-1000/500-70
MLS-2000/1000-70
MLS-3000/2000-70
MLS-5000/2000-65
MLS-6000/4000-60
250 to 500
300 to 800
750 to 1250
1500 to 2500
2000 to 4000
4000 to 6000
4000 to 8000
INPUT
DYNAMIC
RANGE
[dBm]
-70 to 0
-70 to 0
-70 to 0
-67 to +3
-70 to 0
-60 to +5
-55 to +5
TANGENTIAL
SENSITIVITY
[dBm]
-75
-73
-73
-70
-72
-63
-60
VIDEO
FLATNESS
[dB]
±1.0
±1.5
±1.5
±1.5
±2.0
±2.0
±2.0
RISE
TIME
[ns]
FALL RECOVERY
TIME
TIME [MHz]
[ns]
[ns]
15
10
10
15
10
10
10
30
25
25
30
25
25
25
For additional information or technical support, please contact our
Sales Department at (631) 439-9220 or e-mail components@miteq.com
40
35
35
40
35
35
35
H IG H -P E R FO R M A N C E LO G A RITH M IC A M P LIF IE R S
M O DE L: M LS S E RIE S
FE A TURE S
• 70 dB dynamic range at 1 GHz
• Improved sensitivity
• Rise time up to 1 ns
• Fast recovery time
• ±1.5 dB video flatness over 500 MHz
bandwidth • Low output noise for increased
accuracy
• Improved sensitivity through low noise
figure input stages
O P TIO N S
• Customized center frequencies and
frequency agility
• Dynamic range and operational bandwidth
• Custom packaging
• Extended environmental limits
MITEQ’s model IRE0618LI1 Enhanced Image Rejection Mixer utilizes a unique architecture developed to provide
OPERArejection
TIONAL
INPUT
greater than 30 dB of image
across
multioctave bands. This design inherently suppresses image frequenFREQUENCY
DYNAMIC
TANGENTIAL
VIDEO
RISE
FALL
cies by an additional 15 dB over conventional
image rejection mixers without the need for phase and amplitude alignRECOVERY
MODEL
RANGE reliable
SENSITIVITY
TIME
TIME
TIME
ment during
production testRANGE
allowing for consistent
performanceFLATNESS
throughout production.
MLS-375/250-70
MLS-550/500-70
MLS-1000/500-70
MLS-2000/1000-70
MLS-3000/2000-70
MLS-5000/2000-70
250 – 500
300 – 800
750 – 1250
1500 – 2500
2000 – 4000
4000 – 6000
AD D ITIO N AL S P E C IFIC ATIO N S
Log linearity at midband is
O R D E R O P TIO N S
For limited RF output, add suffix “L”.
Typical part number: MLS-375/250-70L.
-70 to 0
-70 to 0
-67 to +3
-67 to +3
-65 to +5
-65 to +5
-75
-73
-70
-70
-68
-68
1
1.5
1.5
1.5
2
2
15
10
10
15
10
10
30
25
25
30
25
25
40
35
35
40
35
35
M LS S E RIE S O U TLIN E D RAW IN G S
O U TLIN E A
1.800 [45.72]
1.690 [42.93]
1.535 [38.99]
1.300 [33.02]
1.015 [25.78]
.055
[1.40]
.025
[0.64]
.260
[6.60]
.185
[4.70]
.090
[2.29]
.055 [1.40]
.350
[8.89]
.725
[18.42]
.070
[1.78]
VIDEO GND -V
OUT
RF IN
+V
.890
[22.61]
1.000
[25.40]
RF OUT
.400
[10.16]
.140
[3.56]
TYPE SMA FEMALE
FIELD REPLACEABLE
CONNECTOR (TYP. 3
.900 [22.86]
1.400
O U TLIN E G
2–56 TAP THRU
4 PLACES
.070 [1.78]
2.380 [60.45]
.120 [3.05]
LOG OUT
+V
-V
RF OUT
.930
[23.62]
RF IN
2.500 [63.50]
OSMP SHROUD
MA/COM P/N 2998-5041-02
(TYP. 3 PLACES)
O U TLIN E P
2.500 [63.50]
.090 [2.29]
.69
[17.53] .56
[14.22]
2.160 [54.86]
.090
[2.29]
.910
[23.11]
.44 .31 [7.87]
[11.18]
N/C
IF OUT
-V
+V
VD OUT
1.00
[25.40]
IF IN
.10 [25.4]
2–56UNC X .150 [3.81] DEEP
4 PLACES ON FARSIDE
.025
[0.64]
NOTE: WEIGHT........................................... Approximately 30.75 grams
DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
DIA.
.090
[2.29]
PIN
.75
[19.05]
.25 [6.35]
ULTRAFAS T W IDE BAN D H IG H-FRE Q UE N C Y LO G ARITHM IC AM PLIFIE RS
M O D E L: M LIF S E RIE S
FE A TURE S
• 70 dB dynamic range at 1 GHz
• Improved sensitivity
• Rise time up to 1 ns
• Fast recovery time
• ±1.5 dB video flatness over 500 MHz
bandwidth • Low output noise for increased
accuracy
• Improved sensitivity through low noise
figure input stages
O P TIO N S
• Customized center frequencies and
frequency agility
• Dynamic range and operational bandwidth
• Custom packaging
• Extended environmental limits
CENTER
OPERATIONAL
RECOVERYMODEL
TIME
TIME
MLIF-500/100-70
MLIF-750/500-65
MLIF-900/100-75
MLIF-1000/500-60
MLIF-1000/500-75
MLIF-1500/500-60
MLIF-1800/200-70
500
750
900
1000
1000
1500
1800
100
500
100
500
500
500
200
DYNAMIC
TANGENTIAL
FREQUENCY BANDWIDTH
TIME
-70 to 0
-65 to 0
-70 to +5
-60 to 0
-70 to +5
-60 to 0
-65 to +5
VIDEO
RANGE
-73
-68
-73
-63
-73
-63
-68
1
1.5
1
1
2
1.5
1
ADDITIO N AL S PE C IFIC ATION S
The above models are available in 'A, B, G, K and M' housings.
Linearity measured at center frequency and 25°C is ±1 dB.
Add ±0.5 dB over operating temperature of -40 to +85°C and ±0.5 dB over operating
bandwidth. Slope is 15 mV/dB at center frequency and 25°C.
Slope variations of ±5% will occur over operating temperature of -40 to +85°C.
An additional ±5% variation will occur over operating bandwidth.
Video output is DC coupled and rated into 93
O RD E R O P TIO N S
For ±15 VDC, add suffix “C”.
For limited IF output at 0 dBm nominal, (VSWR < 2.0:1 typical) add suffix “L”.
Typical part number: MLIF-1000/500-75BCL (for 'B' housing at ±15 VDC with limited IF output).
NOTE: FOR MODIFICATION OF OUR STANDARD MODELS, PLEASE CONSULT FACTORY.
RISE
FALL
SENSITIVITY
5
3
10
3
10
3
10
15
10
30
10
30
10
30
FLATNESS
25
15
45
15
45
15
45
M LIF S E RIE S TYP IC AL TE S T D ATA
PULSE
RESPONSE
LOG ERROR (dB)
MILLIVOLTS/DIV.
LOG LINEARITY
(MLIF-1000/500-70)
10%
Ch 1 250 mV
M 10.0 ns/d
INPUT POWER (dBm)
M LIF S E RIE S O U TLIN E D RAW IN G S
O U TLIN E A
4.00 [101.60]
GROU
ND
.60 [15.24]
.35 [8.89]
+VDC
2.00
[50.80]
1.20
[30.48]
1.00 [25.40]
1.80
1.50 [45.72]
[38.10]
.60 [15.24]
.38 [9.65] TYP.
RF INPUT
.35 [8.89]
.3750 [9.53]
.13 [3.30]
TYPE SMA FEMALE
CONNECTION
BOTH ENDS
RF
OUTPUT
.28 [7.11]
4–40 MOUNTING HOLES
(2 PLACES)
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
M LIF S E RIE S O U TLIN E D RAW IN G S
O U TLIN E B
3.53 [89.66]
3.281 [83.34]
.125 [3.18]
.125 [3.18]
4–40 THREAD THRU
4 MOUNTING HOLES
GROUND
1.50
[38.10]
.235 [5.97]
+VDC
-VDC
1.25
[31.75]
DC OFFSET
ADJUST
1.08
.805 [27.43]
[20.45]
.38 [9.65] TYP.
.51
[12.95]
3.02
[76.71]
VIDEO OUTPUT
.235 [5.97]
.578 [14.68]
.29 [7.37]
.47 [11.94]
IF INPUT
TYPE SMA FEMALE
CONNECTORS
(3 PLACES)
O U TLIN E G *
.125 [3.18]
.125 [3.18]
3.78 [96.01]
3.531 [89.69]
4–40 THREAD THRU
4 MOUNTING HOLES
GROUND
1.50
[38.10]
+VDC
-VDC
1.25
[31.75]
.38 [9.65] TYP.
.531 [13.49]
2.50 [63.50]
3.25 [82.55]
LIMITED IF
OUTPUT
.235 [5.97]
VIDEO OUTPUT
.47 [11.94]
IF INPUT
TYPE SMA FEMALE
CONNECTORS
(3 PLACES)
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
* ABOVE DRAWING INCLUDES LIMITED IF OUTPUT (OPTIONAL).
.235 [5.97]
DC OFFSET
ADJUST
1.08
.805 [27.43]
[20.45]
.578 [14.68]
.29 [7.37]
M LIF S E RIE S O U TLIN E D RAW IN G S
O U TLIN E K *
4.375 [111.13]
4.125 [104.78]
.125 [3.18]
.125 [3.18]
1.50
[38.10]
1.25
[31.75]
.140 [3.56] DIA.
MOUNTING HOLES
(TYP. 4 PLACES)
PWR
LIMITED
IF VIDEO
OUT OUT OFFSET
IF
IN
CONNECTOR
CANNON
MDM9SH003P
MATE & CABLE
SUPPLIED
SMA
FEMALE
CONNECTOR
(TYP. 3 PLACES)
3.578 [90.88]
3.031 [76.99]
2.375 [60.33]
.453
[11.51]
.234 [5.94]
O U TLIN E M
SPARE
OFFSET
RET
VIDEO
+VDC
-VDC
RET
IF IN
.493 [12.52]
.03 [.76] DIA. PINS TYP.
.15 [3.81] MIN.
.075 [1.91]
3.531 [89.69]
3.381 [85.88]
3.331 [84.61]
.255 [6.48]
.295 [7.49]
.455 [11.56]
.615 [15.62]
.775
[19.68] .935
[23.75] 1.095
[27.81]
1.35
[34.29]
.30 .16
[7.62] [4.06]
1.50
[38.10]
.095 [2.41]
2—56 THD X .16 [4.06] MIN. DEEP
4 MOUNTING HOLES
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
* ABOVE DRAWING INCLUDES LIMITED IF OUTPUT (OPTIONAL).
D E TE C TO R LO G VID E O A M P LIF IE R S
M O D E L: FB LA S E RIE S
F E ATU RE S
•
•
•
•
Ultra-broadband units
Logarithmic linearity ±1.5 dB max.
Temperature range -20 to +90°C
70 dB dynamic range
O P TIO N S
• Customized center frequencies and
frequency agility
• Extended environmental limits
• Military screening available
MITEQ’s model IRE0618LI1 Enhanced Image Rejection Mixer utilizes a unique architecture developed to provide
OPERArejection
TIONAL across
INPUT
greater than 30 dB of image
multioctave bands. This design inherently suppresses image frequenFREQUENCY
DYNAMIC
TANGENTIAL
VIDEO
cies by an additional 15 dB over conventional image rejection
mixers without
the needRISE
for phaseFALL
and amplitude alignRECOVERY
ment during
production
test
allowing
for
consistent
reliable
performance
throughout
production.
MODEL
RANGE
RANGE
SENSITIVITY
FLATNESS
TIME
TIME
TIME
STANDARD DYNAMIC RANGE
FBLA-0.5/2.0-40AC
FBLA-2/4-40AC
FBLA-4/8-40AC
FBLA-8/12-40AC
0.5 – 2
2–4
4–8
8 – 12
-40 to 0
-40 to 0
-40 to 0
-40 to 0
FBLA-0.1/1-70BC
FBLA-0.5/1.5-70BC
FBLA-1/2-70BC
0.1 – 1
0.5 – 1.5
1–2
-67 to +3
-67 to +3
-65 to +5
-44
-44
-43
-43
0.5
0.5
0.75
1
30
30
35
35
45
45
50
50
150
150
180
180
40
40
40
120
120
120
350
350
350
EXTENDED DYNAMIC RANGE
-70
-70
-68
1.5
1.5
1.5
AD D ITIO N AL S P E C IFIC ATIO N S
For standard and extended dynamic range DLVAs, linearity measured at center frequency and 25°C is ±1 dB.
Add ±0.5 dB over operating temperature of -40 to +85°C and ±0.5 dB over operating bandwidth.
Logging slope for standard dynamic range DLVA is 100 mV/dB at center frequency and 25°C.
Logging slope for extended dynamic range DLVA
is 15 mV/dB at center frequency and 25°C.
Slope variations of ±5% variation will occur over operating bandwidth.
An additional ±5% will occur over operating temperature of -40 to +85°C
Video output is DC coupled and rated into 93
O R D E R O P TIO N S
For ±15 VDC, add suffix “C”.
NOTE: FOR MODIFICATION OF OUR STANDARD MODELS, PLEASE CONSULT FACTORY.
F BLA S E R IE S O U TLIN E D RAW IN G S
O U TLIN E A
2.75 [69.85]
2.550 [64.77]
.100 [2.54]
.100 [2.54]
1.300
[33.02]
1.50
[38.10]
.120 [3.05] ø
MOUNTING HOLE
(TYP. 4 PLACES)
.25 [6.35]
GND
+V
-V
RF
IN
VIDEO
OUT
.38 [9.65]
TYP.
.50 [12.70]
.30 [7.62]
.45
[11.43]
.30 [7.62]
.22 [5.59]
.62 [15.75]
.40
[10.16]
1.05
TYPE SMA FEMALE
CONNECTOR
(TYP. 2 PLACES)
O U TLIN E B
.125 [3.18]
.125 [3.18]
3.53 [89.66]
3.281 [83.34]
4–40 THREAD THRU
4 MOUNTING HOLES
.235 [5.97]
GROUND
1.50
[38.10]
+15 VDC
-15 VDC
1.250
[31.75]
1.080
.805 [27.43]
[20.45]
.38 [9.65] TYP.
.51 [12.95]
.578 [14.68]
.29 [7.37]
3.02 [76.71]
VIDEO OUTPUT
DC OFFSET ADJUST
.47 [11.94]
.235
[5.97]
IF INPUT
TYPE SMA FEMALE CONNECTOR
(TYP. 2 PLACES)
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
H IG H -P E RFO R M AN C E S U C C E S S IVE D E TE C TIO N
IF LO G ARITH M IC AM PLIFIE RS
M O D E L: LIFD S E RIE S
F E ATU RE S
•
•
•
•
•
Up to 85 dB dynamic range
±0.5 dB linearity
Extended environmental limits
Optimized chassis for VME format
Different packaging options
O P TIO N S
• Customized center frequencies and
frequency agility
• Increased dynamic range
• Increased operating bandwidth
• Custom packaging
• Extended environmental limits
• Military screening
MODEL
CENTER
FREQUENCY
TIME
3 dB
BANDWIDTH
LIFD-1002P-80
LIFD-2105P-80
LIFD-3010P-80
LIFD-6020P-80
LIFD-7030P-80
LIFD-12020P-80
LIFD-16040P-80
10
21.4
30
60
70
120
160
2
5
10
20
30
20
40
DYNAMIC
RANGE
RISE
TIME
FALL
-80
-80
-80
-80
-80
-80
-80
0
0
0
0
0
0
0
500
200
100
50
30
50
30
1000
600
300
150
90
150
90
-70 to 0
-70 to 0
20
20
60
60
to
to
to
to
to
to
to
WIDEBAND MODELS
LIFD-300100P-70
LIFD-450300P-70
300
450
100
300
ADDITIO N AL S PE C IFIC ATION S
The above models are available in ‘A, B, G, K and M’ housings.
Linearity measured at center frequency and 25°C is
An additional ±5% variation will occur over operating bandwidth. 1
Video output is DC coupled and rated into 93
O R D E R O P TIO N S
For ±15 VDC, add suffix “C”.
For limited IF output at 0 dBm nominal, (VSWR < 2.0:1 typical) add suffix “L”.
Typical part number: LIFD-6020P-80BCL (for ‘B’ housing at ±15 VDC with limited IF output).
Note:1 Wideband models are operational over specified bandwidth and have typically greater 3 dB
NOTE: FOR MODIFICATION OF OUR STANDARD MODELS, PLEASE CONSULT FACTORY.
LIFD S E RIE S TYP IC AL TE S T D ATA
LINEARITY (dB)
LOGGING ACCURACY
(LIFD-3010P-
-80
-60
-40
-20
0
INPUT POWER (dBm)
LIF D S E R IE S O U TLIN E D RAW IN G S
O U TLIN E A
4.00 [101.60]
GROU
ND
.60 [15.24]
.35 [8.89]
+VDC
2.00
[50.80]
1.20
[30.48]
1.00 [25.40]
1.80
1.50 [45.72]
[38.10]
.60 [15.24]
.38 [9.65] TYP.
RF INPUT
.35 [8.89]
.3750 [9.53]
.13 [3.30]
TYPE SMA FEMALE
CONNECTION
BOTH ENDS
RF
OUTPUT
.28 [7.11]
4–40 MOUNTING HOLES
(2 PLACES)
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
LIF D S E R IE S O U TLIN E D RAW IN G S
O U TLIN E B
.125 [3.18]
.125 [3.18]
3.53 [89.66]
3.281 [83.34]
4–40 THREAD THRU
4 MOUNTING HOLES
GROUND
1.50
[38.10]
.235 [5.97]
+VDC
-VDC
1.25
[31.75]
DC OFFSET
ADJUST
1.08
.805 [27.43]
[20.45]
.38 [9.65] TYP.
.51
[12.95]
3.02
[76.71]
.578 [14.68]
.29 [7.37]
VIDEO OUTPUT
.235 [5.97]
.47 [11.94]
IF INPUT
TYPE SMA FEMALE
CONNECTORS
(3 PLACES)
O U TLIN E G *
.125 [3.18]
.125 [3.18]
3.78 [96.01]
3.531 [89.69]
4–40 THREAD THRU
4 MOUNTING HOLES
GROUND
1.50
[38.10]
+VDC
-VDC
1.25
[31.75]
.38 [9.65] TYP.
.531 [13.49]
2.50 [63.50]
3.25 [82.55]
LIMITED IF
OUTPUT
.235 [5.97]
VIDEO OUTPUT
.47 [11.94]
IF INPUT
TYPE SMA FEMALE
CONNECTORS
(3 PLACES)
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
* ABOVE DRAWING INCLUDES LIMITED IF OUTPUT (OPTIONAL).
.235 [5.97]
DC OFFSET
ADJUST
1.08
.805 [27.43]
[20.45]
.578 [14.68]
.29 [7.37]
LIF D S E R IE S O U TLIN E D RAW IN G S
O U TLIN E K *
4.375 [111.13]
4.125 [104.78]
.125 [3.18]
.125 [3.18]
1.50
[38.10]
1.25
[31.75]
.140 [3.56] DIA.
MOUNTING HOLES
(TYP. 4 PLACES)
PWR
LIMITED
IF VIDEO
OUT OUT OFFSET
IF
IN
CONNECTOR
CANNON
MDM9SH003P
MATE & CABLE
SUPPLIED
SMA
FEMALE
CONNECTOR
(TYP. 3 PLACES)
3.578 [90.88]
3.031 [76.99]
2.375 [60.33]
.453
[11.51]
.234 [5.94]
O U TLIN E M
SPARE
OFFSET
RET
VIDEO
+VDC
-VDC
RET
IF IN
.493 [12.52]
.03 [.76] DIA. PINS TYP.
.15 [3.81] MIN.
.075 [1.91]
3.531 [89.69]
3.381 [85.88]
3.331 [84.61]
.255 [6.48]
.295 [7.49]
.455 [11.56]
.615 [15.62]
.775
[19.68] .935
[23.75] 1.095
[27.81]
1.35
[34.29]
.30 .16
[7.62] [4.06]
1.50
[38.10]
.095 [2.41]
2—56 THD X .16 [4.06] MIN. DEEP
4 MOUNTING HOLES
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
* ABOVE DRAWING INCLUDES LIMITED IF OUTPUT (OPTIONAL).
C O N S TAN T PH AS E -LIM ITIN G AM PLIFIE RS
M O DE L: LC PM S E RIE S
F E ATU RE S
•
•
•
•
Up to 70 dB dynamic range
±3° phase variation
±5 dB amplitude variation
Fast recovery
O P TIO N S
• Customized center
frequencies •
Custom
packaging
• High-reliability screening
LCPM-3010-70
LCPM-6020-70
LCPM-7030-70
LCPM-12020-70
LCPM-14040-70
LCPM-16040-70
LCPM-200100-70
LCPM-400100-60
CENTER
FREQUENCY
(MHz)
3 dB
BANDWIDTH
(dBm)
DYNAMIC
RANGE
(dBm)
30
60
70
120
140
160
200
400
10
20
30
20
40
40
100
100
-70 to 0
-70 to 0
-70 to 0
-65 to +5
-65 to +5
-65 to +5
-65 to +5
-60 to 0
ADDITIO N AL S PE CIFICATIO N S
The above models are available in ‘A, B and G’ housings.
Custom housings and electrical specifications are also
available. Contact factory for details.
Phase variation is measured at center frequency and 25°C.
Add ±3° over operating temperature of -40 to +85°C.
Output power is 10 dBm nominal at center frequency
and 25°C.
Additional output power variation of ±1 dB will occur over
operating temperature of -40 to +85°C.
Input/output impedance is 50
O R D E R O P TIO N S
For -15 VDC, add suffix “C”.
Matching up to three channels to within ±3° at 25°C is
available. Contact factory for details.
Typical part number: LCPM-16040-70BC (for ‘B’ housing
at -15 VDC).
OUTPUT POWER
VARIATION
(±dB)
PHASE
VARIATION
(±Deg.)
0.5
0.5
0.5
0.5
1
1
1
1
TYP IC AL TE S T D ATA
TYPICALPHASE RESPONSE
VS. INPUT POWER
PHASE RESPONSE (DEGREES)
MODEL
NUMBER
INPUT POWER LEVEL (dBm)
NOTE: FOR MODIFICATION OF OUR STANDARD MODELS, PLEASE CONSULT FACTORY.
3
3
3
5
5
5
5
5
LC P M S E RIE S O U TLIN E D RAW IN G S
O U TLIN E A
GROUND
-15 VDC
IF
1.60
INPUT
[40.64]
.950 [24.13]
1.10 1.35
[27.94] [34.29]
.550 [13.97]
IF
OUTPUT
.38 [9.65] TYP.
RF OUTPUT
.28 [7.11]
TYPE SMA
FEMALE CONNECTOR
(2 PLACES)
RF INPUT
.35 [8.89]
4–40 (2 MOUNTING HOLES)
O U TLIN E B
.125 [3.18]
.125 [3.18]
3.53 [89.66]
3.281 [83.34]
4–40 THREAD THRU
4 MOUNTING HOLES
1.50
[38.10] 1.25
[31.75]
-15 VDC
1.08 [27.43]
.38 [9.65] TYP.
.51
[12.95]
.235 [5.97]
GROUND
3.02
[76.71]
.805 [20.45]
VIDEO OUTPUT
.47 [11.94]
.235
[5.97]
IF INPUT
SMA FEMALE CONNECTOR
(2 PLACES)
O U TLIN E G
2.50 [63.50]
.125 [3.18]
.125 [3.18]
1.50
[38.10]
2.250 [57.15]
4–40 THREAD THRU
W/.156 [3.96] DIA. X .062 [1.57] DEEP
C'BORE EACH SIDE
(4 MOUNTING HOLES)
.235 [5.97]
GROUND
1.25
[31.75]
-15 VDC
.805 [20.45]
.32 [8.13]
.578 [14.68]
.47 [11.94]
2.03 [51.56]
IF OUTPUT
.47 [11.94]
.235
[5.97]
IF INPUT
TYPE SMA FEMALE CONNECTOR
(2 PLACES)
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
FM DM S E RIE S TYPIC AL TE S T DATA
M O D E L: FM D M S E RIE S
F E ATU RE S
• Broadband frequency range
• Operating frequencies to 1000
MHz •
±1% frequency linearity
• DC-coupled video
• Pulse response to 5 ns
• Wide temperature range
O P TIO N S
•
•
•
•
Customized center frequencies
Custom packaging
High-reliability screening
Digital output of short pulses
MODEL
CENTER
FREQUENCY
TIME
FMDM-21.4/4-2
FMDM-30/6-3
FMDM-60/16-4
FMDM-70/20-5
FMDM-140/25-10
FMDM-160/35-15
FMDM-450/50-20
FMDM-750/150-20
21.4
30
60
70
140
160
450
750
PEAK-TO-PEAK
BANDWIDTH
LINEAR
BANDWIDTH
RISE
TIME
FALL
1000
1000
250
150
100
100
100
50
200
120
90
60
50
35
20
20
500
350
250
150
150
100
60
60
100
50
50
50
50
20
20
10
100
50
50
30
30
20
15
10
350
150
150
100
100
50
50
30
SENSITIVITY
NARROW BANDWIDTH MODELS
8
10
20
30
50
60
100
200
4
6
16
20
25
35
50
150
WIDE BANDWIDTH MODELS
FMDM-30/16-6
FMDM-60/30-8
FMDM-70/36-10
FMDM-70/50-15
FMDM-160/50-15
FMDM-300/100-20
FMDM-750/250-25
FMDM-1000/300-40
30
60
70
70
160
300
750
1000
25
50
60
75
75
150
350
500
16
30
36
50
50
100
250
300
ADDITIO N AL S PE CIFICATIO N S
Narrow bandwidth models are available in ‘B, F and E’ housings.
Wide bandwidth models are available in ‘A and B’ housings.
Linearity:
For narrow bandwidth models, error is typically better than ±3% over linear bandwidth at 25°C.
For wide bandwidth models, error is ±5% over linear bandwidth at 25°C.
Add ±2% over operating temperature of -40 to +85°C.
Rated input is 0 dBm.
Usable from -20 to 0 dBm (-10 to 0 dBm for wide bandwidth models).
Input impedance is 50
O R D E R O P TIO N S
For ±15 VDC, add suffix “C”.
NOTE: FOR MODIFICATION OF OUR STANDARD MODELS, PLEASE CONSULT FACTORY.
FM DM S E RIE S TYPIC AL TE S T DATA
ERROR LINEARITY (mV)
TYPICALERROR
LINEARITYVS.FREQUENCY
FREQUENCY (MHz)
TYPICALVIDEO
PULSEPERFORMANCE
303 Aquisitions
Tek Stopped:
1
Ch1 316 mV
M 500 ns/d 1.9248
D 5.00 ns/d
88 mV
FRE Q UE N C Y D IS C RIM IN ATO R S
M O DE L: FM D M W S E RIE S
F E ATU RE S
•
•
•
•
•
Ultra-wide linear bandwidth
Extreme stability over input power
DC-coupled video
Pulse response to 3 ns
Wide temperature range
O P TIO N S
•
•
•
•
Customized center frequencies
Custom packaging
High-reliability screening
Digital output of short pulses
MODEL
NUMBER
OPERATIONAL
FREQUENCY
RANGE
(MHz)
FMDMW-4/4-5
FMDMW-5.5/9-10
FMDMW-2.75/4.5-10
FMDMW-1.4/2.25-10
FMDMW-650/1100-10
FMDMW-500/500-5
FMDMW-600/800-10
2–6
0.8 – 10
0.4 – 5
0.2 – 2.5
100 – 1200
250 – 750
200 – 1000
LINEAR
BANDWIDTH
(MHz)
4000
9
4.5
2.25
1100
500
800
SENSITIVITY
(±mV/MHz)
1.2
32
16
8
4
10
5
RISE
TIME
(ns)
5
10
10
10
10
5
10
VIDEO
LINEARITY
(±%)
3
5
5
5
5
3
4
ADDITIO N AL S PE CIFICATIO N S
Input dynamic range is -10 to +5 dBm. Wider input power ranges available.
Output voltage swing (into 50
O R D E R O P TIO N S
For ±15 VDC, add suffix “C”.
Typical part number: FMDMW-4/4-5C.
NOTE: FOR MODIFICATION OF OUR STANDARD MODELS, PLEASE CONSULT FACTORY.
BANDWIDTH
(MHz)
60
30
30
30
30
60
30
A
A
A
A
B
B
B
FM DM W S E RIE S TYP IC AL TE S T DATA
Vout (V) VS.
INPUT FREQUENCY (MHz)
OVER DIFFERENT POWER LEVELS
(FMDMW-4/4)
LINEARITY (MHz)
VOLTAGE OUT (V)
LINEARITY (MHz) VS.
INPUT FREQUENCY (MHz)
OVER DIFFERENT POWER LEVELS
(FMDMW-4/4)
INPUT FREQUENCY (MHz)
INPUT FREQUENCY (MHz)
Vout (V) VS.
INPUT FREQUENCY
OVER DIFFERENT POWER LEVELS
(FMDMW-600/800)
LINEARITY (MHz)
VOLTAGE OUT (V)
LINEARITY (MHz) VS.
INPUT FREQUENCY(MHz)
OVER DIFFERENT POWER LEVELS
(FMDMW-600/800)
INPUT FREQUENCY (MHz)
INPUT FREQUENCY (MHz)
FM D M O U TLIN E D RAW IN G S
O U TLIN E A
.125 [3.18]
.125 [3.18]
4.625 [117.48]
4.375 [111.13]
DC OFFSET
ADJUST
GROUND
+VDC
-VDC
1.500
[38.10] 1.250
[31.75]
TYPE SMA
FEMALE
CONNECTORS
(2 PLACES)
4–40 TAP THRU C'BORE
.156 [3.96] DIA. .062 [1.57]
DEEP BOTH SIDES
1.080
.805
.578 [20.45] [27.43]
[14.68]
.375 [9.53]
IF
INPUT
.29 [7.37]
.225 [5.72]
VIDEO
OUTPUT
.225 [5.72]
.47 [11.94]
.520 [13.21]
4.105 [104.27]
.256 [6.50]
O U TLIN E B
.125 [3.18]
.125 [3.18]
3.53 [89.66]
3.281 [83.34]
4–40 THREAD THRU
4 MOUNTING HOLES
.235 [5.97]
GROUND
1.50
[38.10]
+15 VDC
-15 VDC
1.250
[31.75]
1.080
.805 [27.43]
[20.45]
.38 [9.65] TYP.
.51 [12.95]
.578 [14.68]
.290 [7.37]
3.02 [76.71]
VIDEO OUTPUT
DC OFFSET ADJUST
.47 [11.94]
.235
[5.97]
IF INPUT
TYPE SMA FEMALE CONNECTOR
(TYP. 2 PLACES)
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
FM D M O U TLIN E D RAW IN G S
O U TLIN E E
2.500 [63.50]
-12VDC
OFFSET
RET
VID OUT
+12VDC
SEE NOTE 1
RET
IF IN
1.000 [25.40]
SEE NOTE 2
.375 MAX. [9.53]
.030
.150 [3.81]
.075
[1.91]
NOTES:
1. TERMINAL IDENTIFICATION SHALL BE MARKED IN
APPROXIMATE POSITION SHOWN.
2. UNLESS OTHERWISE SPECIFIED, ALL DIMENSIONS
ARE
2.350
.075 [1.91]
.09 [2.29]
.135 [3.43]
.425 [10.80] .565 [14.35]
.850 [21.59]
TERMINAL
(3 PLACES)
RFI FILTER
(2 PLACES)
.086(2.18)-56 THD X
.156 (3.96) DEEP MIN.
(4 PLACES)
GROUND STUD
(2 PLACES)
.715 [18.16]
O U TLIN E F
SPARE
OFFSET
RET
VIDEO
+VDC
-VDC
RET
IF IN
.493 [12.52]
.03 [.76] DIA. PINS TYP.
.15 [3.81] MIN.
.075 [1.91]
3.531 [89.69]
3.381 [85.88]
3.331 [84.61]
.255 [6.48]
.295 [7.49]
.455 [11.56]
.615 [15.62]
.775
[19.69] .935
[23.75] 1.095
[27.81]
1.35
[34.29].30 .16
[7.62] [4.06]
1.50
[38.10]
.095 [2.41]
2–56 THD X .16 [4.06] MIN. DEEP
4 MOUNTING HOLES
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
AUTO M ATIC G AIN -C O N TRO L AM PLIFIE RS
M O D E L: AG C S E RIE S
F E ATU RE S
•
•
•
•
Input dynamic range up to 75 dB
Output variation < 2 dB
Multioctave bandwidth
Improved NPR for spectral purity
O P TIO N S
•
•
•
•
Customized center frequencies
Manual gain control
Open or closed-loop operation
Increased or decreased acquisition
MODEL
NUMBER
AGC-7-10.7/4A
AGC-7-21.4/10A
AGC-7-30/10A
AGC-7-60/20A
AGC-7-70/30A
AGC-7-140/40A
AGC-7-160/40A
AGC-7-300/400A
CENTER
FREQUENCY
(MHz)
10.7
21.4
30
60
70
140
160
300
3 dB
BANDWIDTH
(MHz)
4
10
10
20
30
40
40
400
DYNAMIC
RANGE
(dBm)
-70 to 0
-70 to 0
-70 to 0
-70 to 0
-70 to 0
-70 to 0
-70 to 0
-65 to 0
OUTPUT POWER
VARIATION
(±dB)
OUTPUT
POWER
(dBm)
0.5
0.5
0.5
0.5
1
1
1
1.5
10
10
10
10
5
5
5
3
ADDITIO N AL S PE CIFICATIO N S
The above models are available in ‘A’ housing.
Custom housing and electrical specifications are also available. Contact factory for details.
Output power and output power variation is measured at center frequency and 25°C.
Additional output power variation of ±0.5 dB will occur over operating temperature of -40 to +85°C.
Input/output impedance is 50
O R D E R O P TIO N S
For ±15 VDC, add suffix “C”.
All units are available in phase and gain tracking sets up to three channels to within ±5° and ±1 dB at
NOTE: FOR MODIFICATION OF OUR STANDARD MODELS, PLEASE CONSULT FACTORY.
AG C S E RIE S TYPIC AL TE S T DATA
AGC OUTPUT VOLTAGE (VOLTS)
TYPICALMONITORVS.GAIN
(OUTPUTPOWER3dBmNOMINAL)
0
-1.6
-3.2
-4.8
-6.4
-8
-75
-60
-45
-30
-15
0
INPUT POWER (dBm)
AG C S E RIE S O U TLIN E D RAW IN G
O U TLIN E A
5.85 [148.59]
5.45 [138.43]
.20 [5.08]
-15 V
GROUND
CONTROL "V"
OUTPUT
CONTROL "V"
INPUT
+15 V
2.65
[67.31]
IF INPUT
3.05
[77.47]
1.04
[26.42] TYP.
IF OUTPUT
.20 [5.08]
TYPE SMA FEMALE
CONNECTOR
(TYP. 2 PLACES)
.50 [12.70]
.187 [4.75] DIA. THRU
(TYP. 4 PLACES)
1.05 [26.67]
.09 [2.29 ]
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
.715 [18.16] TYP.
M AN UAL VO LTAG E G AIN -C O N TRO L AM PLIFIE RS
M ODE L: VGC SE RIE S
FE ATURE S
•
•
•
•
•
•
Gain control up to 85 dB
IF gain up to 80 dB
Video gain up to 100 dB
Linear mV/dB curve
Detected video
1 dB compression maintained over entire
gain control range
O P TIO N S
•
•
•
•
•
Customized center frequencies
Increased operational bandwidth
Custom packaging
High-reliability screening
Matched sets
MODEL
CENTER
FREQUENCY
TIME
3 dB
BANDWIDTH
GAIN TO
IF OUT
GAIN CONTROL
RANGE
GAIN TO
VIDEO OUT
30
60
60
70
70
120
140
160
10
10
2
10
30
20
40
40
70
70
70
70
70
60
60
60
60
60
60
60
60
50
50
50
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
60
60
60
60
60
50
50
50
80
80
80
80
80
70
70
70
100
100
50
100
30
50
30
30
VGC-7-30/10
VGC-7-60/10
VGC-7-60/20
VGC-7-70/10
VGC-7-70/30
VGC-6-120/20
VGC-6-140/40
VGC-6-160/40
VIDEO
RISE
MODELS WITH VIDEO OUTPUT
VGC-7DV-30/10
VGC-7DV-60/10
VGC-7DV-60/20
VGC-7DV-70/10
VGC-7DV-70/30
VGC-6DV-120/20
VGC-6DV-140/40
VGC-6DV-160/40
30
60
60
70
70
120
140
160
10
10
2
10
30
20
40
40
70
70
70
70
70
60
60
60
ADDITIO N AL S PE C IFIC ATION S
All above models are available in ‘B and D’ housings.
IF output capability is +10 dBm minimum at 1 dB compression.
Noise figure is < 4 dB (30~70 MHz); < 5 dB (120~160 MHz)
Gain control voltage is 0 to -4 V (minimum gain) over specified control range.
Input/output impedance is 50
O R D E R O P TIO N S
For ±15 VDC, add suffix “C”.
NOTE: FOR MODIFICATION OF OUR STANDARD MODELS, PLEASE CONSULT FACTORY.
VG C S E RIE S TYPIC AL TE S T DATA
GAIN (dB)
TYPICAL GAIN
0 -0.5 - -1.5 -2 -2.5 -3 -3.5 -4 -4.5 -5
MAXIMUM GAIN CONTROL (VOLTS)
VG C S E RIE S O U TLIN E D RAW IN G S
O U TLIN E B
3.53 [89.66]
3.281
.125 [3.18]
.125 [3.18]
4–40 THREAD THRU
4 MOUNTING HOLES
.235 [5.97]
DC OFFSET
ADJUST
1.50
[38.10]
GROUND
+15 VDC
-15 VDC
1.25
[31.75]
1.08
[27.43]
.805
[20.45]
.38 [9.65] TYP.
.51 [12.95]
.29
[7.37]
.578
[14.68]
1.25 [31.75]
1.50 [38.10]
2.33 [59.18]
3.02 [76.71]
IF
OUTPUT
VIDEO
OUTPUT
.47 [11.94]
.235 [5.97]
GROUND
GAIN CONTROL
IF INPUT
TYPE SMA FEMALE
CONNECTORS
(3 PLACES)
O U TLIN E D
4.62 [117.35]
4.38 [111.25]
.125 [3.18]
.125 [3.18]
4–40 THREAD THRU
4 MOUNTING HOLES
.235 [5.97]
DC OFFSET
ADJUST
1.50
[38.10]
GROUND
+15 VDC
-15 VDC
1.25
[31.75]
1.08
[27.43]
.805
[20.45]
.32 [8.13] TYP.
.45 [11.43]
2.53 [64.26]
2.88 [73.15]
4.17 [105.92]
1.83 [46.48]
GAIN
CONTROL
VIDEO OUTPUT
SMA FEMALE
.29
[7.37]
.578
[14.68]
.47 [11.94]
.235 [5.97]
IF OUTPUT SMA FEMALE
IF GAIN
IF INPUT SMA FEMALE
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.
M U LTIFUN C TIO N C O M P O N E N TS
M O D E L: LAFD S E RIE S
F E ATU RE S
• Digital outputs for frequency discriminators
and logarithmic amplifiers
• Broadband frequency range
• Pulse response to 5 ns
• 70 dB dynamic range at 1 GHz
• Improved sensitivity
O P TIO N S
•
•
•
•
Customized center frequencies
Increased operational bandwidth
Extended dynamic range
Military screening available
MITEQ’s model IRE0618LI1 Enhanced Image Rejection Mixer utilizes a unique architecture developed to provide
LIMITED IF bands. This design
FREQUENCY
greater than 30 dB of image rejection across multioctave
inherently suppresses image frequenOUTPUT
LOG AMP DISCRIMINATOR
FREQUENCY
FREQUENCY
cies by an additional 15 CENTER
dB over conventional
image
rejection
mixers
without
the
for phaseTOR
and amplitude
align3 dB
POWER
VIDEO
LINEAR needDISCRIMINA
DISCRIMINATOR
MODEL
VARIA
TION performance
RISE TIME
BANDWIDTH
RISE TIME
SLOPE
ment during
productionFREQUENCY
test allowingBANDWIDTH
for consistent
reliable
throughout production.
NUMBER
(MHz)
(MHz)
(±dB)
(ns)
(MHz)
(ns)
(mV/MHz)
LAFD-7-30/10
LAFD-7-60/20
LAFD-7-70/30
LAFD-7-120/40
LAFD-7-160/50
LAFD-6-300/100
LAFD-6-750/200
LAFD-6-1000/300
30
60
70
120
160
300
750
1000
10
20
30
40
50
100
200
300
0.5
0.5
0.5
0.5
1
1
1
1
150
70
50
40
30
20
15
10
6
16
20
24
30
75
150
250
150
70
50
40
30
20
15
10
1000
250
150
100
100
50
20
10
ADDITIO N AL S PE CIFICATIO N S
Input dynamic range is -70 to 0 dBm minimum (30 MHz~160 MHz) and -65 to 0 dBm (300 MHz~1000 MHz).
Log linearity is
O R D E R O P TIO N S
For ±15 VDC, add suffix “C”.
Typical part number: LAFD-7-160/50C (for ±15 VDC).
NOTE: FOR MODIFICATION OF OUR STANDARD MODELS, PLEASE CONSULT FACTORY.
LA FD S E R IE S O U TLIN E D RAW IN G
.75 [19.05]
.21
.50
[5.33] [12.7]
1.35
[34.29]
1.66
[42.16]
1.98
[50.29]
2.73
[69.34]
3.60
[91.44]
TYPE SMA FEMALE
FIELD
REPLACEABLE
CONNECTOR
5.40
[137.16]
- 15 VDC
GROUND
+15 VDC
RF INPUT
LOG OUTPUT
LIMITED IF OUTPUT
DISCRIMINATOR VIDEO OUTPUT
.150 [3.81]
.38 [9.65] TYP.
3.00
[76.20]
.125 [3.18] DIA. MOUNTING HOLE
(TYP. 4 PLACES)
2.700
[68.58]
.150 [3.81]
5.700 [144.78]
6.00 [152.40]
NOTE: DIMENSIONS SHOWN IN BRACKETS [ ] ARE IN MILLIMETERS.