Downtown Transportation Center
Parking Garage
Lighting Analysis
October 27, 2008
Introduction
The purpose of this report is to assist the City with selection of a lamp source for the
Downtown Transportation Center parking garage. We evaluated many lamp options
and layout configurations during our analysis. Summarized are the optimum lamp
types, balancing quality of illumination, efficiency, and cost. Representative light
fixtures were selected to allow us to determine the quantity of lamps required for the
installation. There are various styles of light fixtures available in the metal halide and
fluorescent lamp categories that will perform similarly to those used in this exercise.
Our options are very limited with LED and induction fluorescent systems. The
selected fixtures represent the quality of construction desired for this project.
We are anticipating the top deck will be illuminated with metal halide or LED pole
mounted fixtures along grid 3. Landscape light fixtures with a compact fluorescent
lamp will be placed in the columns along grid 1 to define the edge of the structure.
The top deck was not considered in our evaluation, although information presented
here should assist the City with a lamp decision for the pole mounted fixtures.
Design Criteria
The Illuminating Engineering Society of North America (IESNA) outlines minimum
illumination requirements for parking garages intended for use by the general public.
Values outlined herein are defined in IESNA for preliminary analysis. Our
calculations will be refined as we proceed with a specific layout for the selected lamp
type.
•
•
•
Horizontal Illumination: 1-footcandle minimum, 5-footcandles average on the
covered decks with a 10:1 maximum to minimum uniformity ratio.
Minimum Vertical Illumination: 0.5-footcandles at 5-feet above the parking
surface.
Entrances: 50-footcandles minimum during the day. This higher illumination
level should be carried approximately 70-feet inside the garage to allow a
transition from bright daylight to a lower internal level. Natural daylight may
be considered in the calculation.
Our calculations utilize standard concrete reflectance values: 0.3 for vertical and
horizontal surfaces, 0.2 for the driving surface. Application of a white paint on the
ceiling and vertical beam surfaces will increase the horizontal illumination levels by
about one footcandle. The practical benefit to applying the paint system is increased
ceiling illumination and increased vertical surface illumination above 5-feet. Both of
these elements will increase the sense of personal safety.
Option A – Pulse Start Metal Halide, 175 watt.
Historically, the metal halide lamp has been the standard choice for parking garage
lighting. There are a variety of light fixtures available that have been refined during
the past 15-years to optimize performance of the lamp. The metal halide lamp
performs well in cold, wet environments and has good color rendering properties.
We used a pulse start metal halide lamp in our analysis which provides better lumen
maintenance and longer life than the typical metal halide lamp.
We used the Kim Lighting PGL 5 fixture to model the metal halide lamp. An
enhanced feature with this fixture is the ability to control glare with louvers. The
luminaire also provides approximately 10-percent uplight to illuminate the ceiling.
Egress illumination would be provided with separate battery lighting units.
Option B – Induction Fluorescent, 165 watt.
The induction fluorescent system utilizes a high frequency magnetic field to supply
energy to the low pressure gas inside the bulb. The electromagnetic field is produced
by a generator coupled to an antenna. Because the assembly does not include an
electrode, the life of the system can be very long. The system provides constant light
output, instant starting, and good performance at low temperatures.
Use of this technology is not widespread. Light fixture manufacturers have had
difficulty dissipating the heat generated by the lamp, causing premature failure of the
generator. The Widelite RSP series with the 165 watt induction fluorescent lamp was
used in our analysis. Kim Lighting offers an 85 watt lamp, which does not provide
sufficient illumination levels. Egress illumination would be provided with separate
battery lighting units.
Option C – Light Emitting Diode (LED), 54 watts.
The use of LED’s for general illumination is becoming more viable with increased
lumen-per-watt output and better color rendering. New products are continually
being introduced to the market. LED’s provide high efficiency and superior life, and
cold temperatures do not negatively impact performance.
Beta Lighting has developed a parking garage light fixture that is the basis of our
analysis. Illumination levels decrease rapidly at the perimeter so the maximum to
minimum ratio is higher than our other options. This particular fixture uses (2) light
bars with 20 LED’s per bar. The LED driver is available with multiple output current
ratings allowing fixture performance to be fine-tuned after installation. LED life is
sacrificed with increased lumen output. Egress illumination is integral to the fixtures
with battery back-up. It is worthy to note the photometric data provided by the
manufacturer is preliminary.
Option D – Linear Fluorescent lamp, (2) F32T8, 56 watts.
Fluorescent lamps provide a high lumen per watt ratio, good lamp life, and many
options for color rendering properties. We generally use linear fluorescent lamps
sparingly in outdoor applications. They operate best in the range of 40-80 degrees
Fahrenheit. Below this range, there is a decrease in light output and difficulty in
starting. Walker Parking Consultants recommends the Zumtobel Cold Spot
Optimizer (CSO) to address cold weather performance. The CSO is an aluminum
sleeve that regulates the temperature at the electrode end of the lamp. Zumtobel inhouse testing of the CSO produced favorable results in the range of -4 to 32 degrees
Fahrenheit. Use of the CSO will limit our light fixture choices to Zumtobel. We
have never applied the CSO technology in the field.
The Zumtobel Chiaro fixture was utilized in our fluorescent lighting layout. The
fixture has an option for 20% uplight. The fluorescent system may present the
opportunity for daylight harvesting along the perimeter of the facility by separately
switching the lamps. Egress illumination is integral to the fixtures with battery backup.
Financial Analysis
We used the third floor deck to establish a typical layout for each lamp type. We
extended the typical layout to the other two floors to determine the approximate total
quantity of lamps shown in the Lighting Cost Summary.
Metal halide and fluorescent lamps require fairly uniform investment, while the
induction fluorescent and LED options require only periodic investment. A present
worth calculation was performed to compare the options. The life of the system was
considered to be 34-years. The cost of lamp replacement includes labor. The energy
rate reflects the current ‘power cost adjustment’ being applied by AEL&P. Less
tangible costs such as cleaning, disposal, and ballast replacement were not considered
and present a small margin of error.
Downtown Transportation Center
Parking Garage Lighting Cost Summary
Haight & Associates, Incorporated
October 27, 2008
Installed
kW
Cost
Annual
Annual
Annual
Annual Lamp
Total Annual
Hours
kWH Cost
Demand Cost
Cost
Cost
Option A (pulse start metal halide)
$54,230.00
12.0
8760
$7,919.74
$1,058.40
$1,131.32
$10,109.47
Option B (induction fluorescent)
$75,980.00
11.0
8760
$7,259.76
$970.20
$753.99
$8,983.95
Option C (LED)
$124,260.00
5.7
8760
$3,761.88
$502.74
$2,439.30
$6,703.91
Option D (fluorescent)
$93,195.00
6.1
8760
$4,025.87
$538.02
$443.05
$5,006.93
Lamp/Labor
Lamp
Lamp life
Annual
Annual Lamp
Cost
Qty
hours
Cost
$1,131.32
Option A (pulse start metal halide)
$33.40
58
15000
8760
Option B (induction fluorescent)
$148.40
58
100000
8760
$753.99
Option C (LED, 2 bars per fixture)
$191.60
218
150000
8760
$2,439.30
Option D (fluorescent, two lamp)
$5.80
218
25000
8760
$443.05
Notes:
Installed Cost: Fixture and 20-feet of conduit and wire.
kW: Total power used by lighting system.
kWH: Operating hours x kW x $0.07534/kWH
Demand: kW x $7.35/kW
Downtown Transportation Center
Parking Garage Lighting Systems
Present Worth Calculation
Option A (Pulse Start Metal Halide)
Installed cost: $54,230
Annual energy cost: $8,978
Lamp replacement every 1.7 years: $1,937
PA = 54230 + 10109 (16.193)
PA = $217,925
Option B (Induction Fluorescent)
Installed cost: $75,980
Annual energy cost: $8,229
Lamp replacement at 11.4 years: $8,607
Lamp replacement at 22.8 years: $8,607
PB = 75980 + 8229 (16.193) + 8607 (0.5734) + 8607 (0.3288)
PB = $216,997
Option C (LED)
Installed cost: $124,260
Annual energy cost: $4,264
Lamp replacement at 17 years: $41,769
PC = 124260 + 4264 (16.193) + 41769 (0.4363)
PC = $211,530
Option D (Fluorescent)
Installed cost: $93,195
Annual energy cost: $4,564
Lamp replacement every 2.9 years: $1,264
PD = 93195 + 5006 (16.193)
PD = $174,257
Notes:
1. Compound interest factors (5%) from Principles of Engineering Economy, 6th
Edition.
2. Annual costs converted to present worth as uniform series.
3. Lamp replacement for induction fluorescent and LED converted to present worth
as single payment.
A
B
D
C
E
F
G
H
J
K
L
M
N
Q
R
S
T
U
1
V
0.8
1.4
1.8
1.9
1.9
1.9
1.9
1.9
2.0
1.9
1.8
1.8
1.8
1.7
1.7
1.7
1.7
1.7
1.8
1.8
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.8
1.7
1.7
1.7
1.7
1.7
1.7
1.7
1.6
1.6
1.8
1.9
1.7
1.8
1.8
1.3
1.6
2.9
3.4
3.4
3.5
3.5
3.4
3.4
3.5
3.4
3.2
3.2
3.2
3.1
3.0
3.0
3.0
3.0
3.1
3.2
3.0
3.0
3.1
3.1
3.0
3.0
3.1
3.0
2.9
3.0
3.1
3.1
3.0
3.1
3.1
3.0
3.0
3.0
3.0
2.8
2.7
3.1
3.2
3.2
3.3
3.1
2.8
2.2
1.4
1.0
0.8
3.2
5.0
5.4
5.6
5.5
5.5
5.5
5.5
5.5
5.5
5.2
5.0
5.0
5.0
4.8
4.8
4.8
4.9
4.9
5.0
4.9
4.7
4.8
4.9
4.9
4.7
4.8
4.9
4.8
4.7
4.9
5.0
4.8
4.8
4.9
4.9
4.8
4.8
4.7
4.6
4.3
5.0
5.5
5.5
5.5
5.1
4.4
3.6
2.4
1.9
1.5
1.0
0.9
2.7
3.5
4.7
6.8
6.8
7.1
8.5
7.8
7.4
8.1
7.9
7.2
7.9
7.9
6.5
6.5
7.6
6.7
6.1
6.7
7.5
6.5
6.4
7.3
7.2
6.2
6.5
7.6
7.0
6.2
6.5
7.6
6.9
6.2
6.8
7.6
6.5
6.2
7.0
7.2
6.2
6.1
7.0
6.0
7.0
8.3
8.1
7.5
7.6
6.7
5.0
3.6
2.9
2.5
1.9
1.5
5.2
6.3
7.7
8.6
8.3
8.2
9.2
9.1
8.7
9.0
8.9
8.3
8.4
8.5
7.6
7.3
8.0
7.5
7.0
7.4
8.0
7.3
7.2
7.9
8.1
7.4
7.3
8.2
8.0
7.3
7.5
8.3
8.0
7.4
7.4
8.0
7.4
7.1
7.5
7.8
7.1
6.9
7.5
6.8
8.2
9.2
9.4
9.5
9.3
7.9
6.0
5.2
4.6
3.9
3.3
2.5
5.7
7.7
8.4
8.7
9.4
9.4
9.2
9.7
10.0
9.3
9.2
9.3
8.3
8.0
8.4
7.9
7.4
7.5
8.0
7.6
7.4
7.8
8.2
7.7
7.9
8.7
8.5
8.0
8.1
8.7
8.5
8.2
8.5
8.9
8.0
7.4
7.8
8.1
7.4
7.3
7.9
7.7
7.0
7.3
9.2
9.7
10.4
10.6
9.4
8.4
7.1
7.4
6.7
5.5
5.1
10.6
10.0
9.9
8.0
7.3
7.3
7.0
6.4
6.5
7.9
7.4
8.3
8.5
7.4
6.4
4.9
3.6
2.9
A
6.0
8.0
A
8.9
9.1
9.7
A
10.0
9.8
10.0
10.4
A
9.6
9.3
9.3
A
8.4
8.0
8.2
A
7.9
7.4
7.4
7.9
A
7.6
7.4
7.8
8.2
A
7.8
8.0
8.9
A
9.1
8.6
8.5
9.1
A
9.1
8.8
8.9
9.3
A
8.4
7.7
7.6
8.0
A
7.5
7.3
7.7
A
7.7
7.1
7.4
9.3
A
9.8
10.5
A
5.7
7.1
9.3
10.3
9.7
10.0
11.4
10.7
9.8
9.9
9.2
8.3
8.6
8.5
7.3
7.2
8.1
7.4
6.8
7.4
8.0
7.2
7.2
8.2
8.4
8.2
8.9
10.4
9.7
8.9
9.4
10.6
9.5
8.4
8.4
8.5
7.3
7.0
7.6
7.7
6.9
6.9
7.6
7.1
8.6
9.7
10.2
9.9
10.2
10.3
A
4.9
6.1
8.6
10.3
9.7
9.8
11.3
10.6
8.7
8.8
8.3
7.1
7.5
7.7
6.4
6.2
7.2
6.5
5.9
6.4
7.2
6.3
6.2
7.2
7.7
7.2
8.1
10.3
10.1
9.1
9.3
10.5
9.4
7.6
7.3
7.7
6.6
6.0
6.6
7.0
6.0
6.0
6.7
6.0
7.5
8.8
9.0
8.9
9.3
8.7
7.7
7.7
8.0
8.3
8.0
6.4
4.9
3.9
3.7
3.6
4.8
6.3
8.0
9.4
9.4
8.6
7.9
6.9
6.0
5.8
5.4
5.1
4.9
4.8
4.7
4.6
4.5
4.5
4.5
4.5
4.7
4.8
4.8
5.1
5.6
6.4
7.3
8.3
9.2
8.7
7.7
7.0
6.2
5.4
5.0
4.8
4.7
4.5
4.5
4.6
4.5
4.3
4.3
5.6
6.3
6.4
6.8
7.4
7.2
8.3
7.9
6.9
7.2
7.6
7.0
5.9
4.6
4.4
2.6
3.6
4.9
6.4
8.1
8.2
6.9
5.8
4.8
4.0
3.7
3.5
3.2
3.0
2.9
2.9
2.8
2.8
2.8
2.8
2.8
2.9
3.0
3.1
3.3
3.9
4.7
5.5
6.7
8.0
7.6
6.2
5.1
4.4
3.7
3.2
3.0
2.9
2.8
2.8
2.8
2.8
2.8
2.9
3.6
4.5
4.9
4.9
5.9
6.4
6.9
7.0
6.9
7.3
8.1
8.1
7.3
5.3
4.2
A
A
A
2.8
3.9
4.8
5.4
5.6
5.1
4.4
3.5
2.8
2.4
2.0
1.8
1.7
1.6
1.6
1.6
1.6
1.5
1.6
1.6
1.6
1.7
1.9
2.3
2.7
3.5
4.4
5.0
5.4
5.4
5.1
4.1
3.0
2.5
2.1
1.8
1.6
1.6
1.6
1.6
1.6
1.6
1.8
2.3
3.0
4.0
3.8
4.9
6.1
6.5
6.9
7.4
8.0
7.9
7.8
7.2
5.3
1.9
2.0
3.6
3.9
3.9
6.6
7.5
7.9
8.2
8.7
8.0
7.0
6.1
5.4
5.0
7.9
8.8
9.2
9.1
9.1
7.6
6.5
5.5
5.4
7.5
8.5
8.9
9.4
9.6
9.9
7.7
6.2
5.4
4.6
7.6 A
8.9
9.2
9.8
9.0
8.4
7.5
6.2
5.2
8.2
7.7
7.8
6.4
4.9
3
2
1.9
A
5.0
7.1
8.1
9.0
9.3
A
7.7
Downtown Transportation Center - Level 3
Option A - Metal Halide Footcandle
Luminaire Schedule
Qty Label Description
22
A
PGL62_175PMH-ED17
[MANUFAC]
KIM LIGHTING, INC_
Watts
175
Lumens
14000
8.3
8.1
8.0
7.3
7.0
5.7
4.2
6.8
5.5
4.6
3.9
A
B
D
C
E
F
G
H
J
K
L
M
N
Q
R
S
T
U
1
V
0.5
0.8
1.0
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.0
1.0
1.0
0.9
0.9
0.9
1.0
0.9
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.1
1.0
1.0
1.0
1.1
1.0
1.0
1.0
1.0
1.0
1.0
1.0
0.9
0.9
0.9
1.1
1.1
1.0
1.0
1.0
0.7
0.8
1.4
1.6
1.7
1.8
1.7
1.7
1.7
1.8
1.7
1.6
1.5
1.5
1.5
1.4
1.4
1.5
1.5
1.5
1.6
1.5
1.6
1.6
1.6
1.5
1.5
1.6
1.6
1.6
1.6
1.6
1.6
1.5
1.5
1.5
1.5
1.5
1.5
1.4
1.4
1.4
1.7
1.7
1.7
1.7
1.5
1.4
1.2
0.9
0.7
0.6
1.7
2.5
2.7
2.8
2.8
2.8
2.8
2.8
2.8
2.7
2.6
2.5
2.4
2.4
2.3
2.4
2.4
2.4
2.5
2.6
2.5
2.5
2.5
2.5
2.4
2.4
2.6
2.5
2.5
2.5
2.6
2.5
2.4
2.5
2.5
2.4
2.4
2.4
2.3
2.2
2.3
2.7
2.8
2.8
2.7
2.4
2.1
1.8
1.3
1.1
0.9
0.7
0.6
1.9
2.7
3.0
3.8
4.3
4.4
4.4
4.6
4.7
4.6
4.7
4.6
4.3
4.2
4.1
4.0
3.9
3.8
3.9
3.9
3.9
4.0
4.2
4.0
4.1
4.2
4.0
3.8
3.9
4.2
4.1
4.0
4.1
4.2
4.1
3.9
4.0
4.1
3.9
3.8
4.0
3.9
3.7
3.8
4.6
4.8
4.9
4.7
4.0
3.4
2.7
1.9
1.7
1.4
1.2
0.9
4.5
6.0
6.5
6.6
6.9
7.0
6.8
7.2
7.5
7.3
7.4
7.4
6.7
6.4
6.6
6.3
5.8
6.0
6.3
6.1
5.9
6.3
6.6
6.2
6.3
6.7
6.3
5.7
6.0
6.6
6.5
6.1
6.3
6.7
6.2
5.9
6.3
6.5
6.0
5.9
6.3
6.2
5.6
6.1
7.4
7.8
8.0
7.6
6.5
5.3
4.1
3.0
2.6
2.2
1.9
1.4
5.8
8.0
8.5
8.6
9.5
9.5
8.8
9.4
10.1
9.6
9.8
9.9
8.7
8.3
8.9
8.4
7.4
7.8
8.5
8.1
7.5
8.4
8.9
8.1
8.1
9.0
8.4
7.2
7.7
9.1
8.8
7.8
8.3
9.1
8.2
7.5
8.3
8.7
7.8
7.5
8.4
8.3
7.3
8.0
10.0
10.5
11.0
10.7
9.3
8.1
6.2
4.8
4.3
3.8
3.1
11.1
10.8
10.4
8.1
6.7
6.5
6.2
4.7
3.9
8.2
7.6
8.6
8.5
6.4
4.7
3.5
2.6
1.9
D
5.7
7.8
D
8.5
8.6
9.6
D
9.7
9.0
9.3
9.9
D
9.4
9.4
9.6
D
8.5
8.0
8.6
D
8.2
7.3
7.5
8.2
D
7.8
7.3
8.1
8.6
D
7.9
7.9
8.8
D
8.4
7.4
7.9
9.2
D
9.0
8.0
8.2
8.9
D
8.1
7.3
8.0
8.4
D
7.6
7.3
8.1
D
8.1
7.1
7.8
9.8
D
10.3
11.0
D
4.3
5.7
6.6
7.2
7.9
8.1
7.6
7.4
7.3
7.0
6.9
6.9
6.4
6.0
6.1
5.9
5.5
5.5
5.8
5.7
5.5
5.9
6.2
5.9
5.9
6.4
6.4
6.2
6.8
7.8
7.6
6.8
6.5
6.6
6.1
5.6
5.9
6.0
5.6
5.5
5.8
5.8
5.3
5.7
7.0
7.6
8.1
8.6
9.4
9.7
D
2.9
3.9
5.0
6.2
7.2
7.3
6.5
5.6
5.0
4.7
4.5
4.4
4.1
3.9
3.8
3.7
3.5
3.5
3.6
3.6
3.5
3.7
3.9
3.9
4.0
4.3
4.6
5.1
6.2
7.2
7.0
5.9
5.0
4.6
4.1
3.8
3.8
3.8
3.6
3.6
3.6
3.6
3.5
3.6
4.4
4.9
5.2
5.8
6.7
6.9
6.4
6.9
8.2
8.3
6.8
5.4
4.5
3.4
2.3
2.0
2.8
4.1
6.0
7.9
7.9
6.2
4.6
3.6
3.1
2.9
2.8
2.6
2.4
2.3
2.3
2.2
2.2
2.2
2.2
2.2
2.3
2.5
2.5
2.6
2.9
3.5
4.5
6.4
8.1
7.6
5.6
4.1
3.3
2.8
2.5
2.4
2.4
2.2
2.2
2.3
2.3
2.2
2.2
2.7
3.1
3.3
3.7
4.3
4.5
4.6
5.2
6.1
6.5
6.5
6.7
6.3
4.6
3.0
1.5
2.2
3.5
5.5
7.7
7.8
5.7
3.8
2.7
2.2
1.9
1.8
1.7
1.5
1.4
1.4
1.4
1.4
1.3
1.4
1.4
1.5
1.6
1.6
1.8
2.1
2.7
3.9
5.9
7.9
7.5
5.2
3.4
2.5
2.0
1.7
1.6
1.5
1.4
1.4
1.5
1.5
1.5
1.5
1.8
2.1
2.4
2.6
3.1
3.3
3.6
4.0
4.5
5.1
6.0
7.6
7.9
5.6
4.0
D
D
D
1.6
2.4
4.0
5.4
5.6
4.1
2.8
2.0
1.5
1.3
1.2
1.1
1.0
0.9
0.9
0.9
0.9
0.8
0.9
0.9
1.0
1.1
1.1
1.3
1.6
2.0
2.8
4.3
5.6
5.4
3.9
2.6
1.8
1.4
1.2
1.1
1.0
0.9
0.9
1.0
1.0
1.0
1.2
1.3
1.5
1.9
2.1
2.5
3.1
3.3
3.5
3.8
4.3
5.3
6.9
7.2
5.2
1.3
1.3
2.0
2.1
2.3
3.9
4.0
3.9
3.8
4.0
4.5
5.1
5.0
3.9
4.4
6.0
5.8
5.3
4.7
4.3
4.2
4.2
3.6
3.1
8.1
8.9
8.5
7.6
6.4
5.4
4.9
4.3
3.4
2.5
8.6 D
10.3
10.5
10.0
8.2
7.1
6.8
5.7
3.7
8.4
8.1
8.6
7.1
4.6
3
2
1.0
D
4.9
7.0
8.6
9.6
9.8
D
6.4
Downtown Transportation Center - Level 3
Option B - Induction Fluorescent Footcandle Printout
Luminaire Schedule
Qty Label Description
22
D
RSPQL-165-R
[MANUFAC]
WIDELITE
Watts
165
Lumens
9600
6.8
6.9
6.5
7.1
7.8
6.5
4.3
5.1
5.5
4.3
3.4
A
B
D
C
E
F
G
H
J
K
L
M
N
Q
R
S
T
U
1
V
4.6
7.0
6.0
0.7
1.0
1.1
1.3
1.2
1.2
1.4
1.4
1.2
1.3
1.3
1.1
1.1
1.2
1.1
1.1
1.1
1.1
1.1
1.1
1.2
1.2
1.1
1.1
1.2
1.1
1.1
1.1
1.2
1.1
1.1
1.2
1.2
1.1
1.1
1.2
1.2
1.1
1.1
1.2
1.0
1.0
1.1
1.0
0.7
0.5
0.3
2.1
3.0
3.5
4.1
3.8
3.7
4.4
4.3
3.7
4.1
4.2
3.5
3.4
3.7
3.4
3.2
3.3
3.5
3.3
3.2
3.6
3.7
3.3
3.3
3.8
3.6
3.2
3.4
3.7
3.4
3.2
3.5
3.7
3.4
3.3
3.6
3.7
3.3
3.3
3.6
3.2
3.1
3.8
4.0
2.4
2.1
1.8
1.1
0.7
0.4
0.3
4.6
7.8
8.0
7.2
8.2
8.9
8.9
9.1
8.9
8.1
8.1
8.5
7.7
6.3
7.4
8.1
7.1
6.0
7.5
8.1
7.1
6.8
8.1
7.8
6.5
7.3
8.2
7.3
6.0
7.5
8.2
7.1
6.3
7.9
8.2
6.8
6.7
8.1
7.8
6.2
8.4
9.2
8.8
8.1
7.3
6.2
5.7
3.4
2.2
2.1
1.2
0.8
0.5
7.3
11.0
11.0
8.5
9.9
12.0
A
10.9
11.2
12.1
A
10.0
9.5
11.4
A
10.1
7.2
9.2
11.1
A
8.9
6.7
9.6
11.1
A
8.7
7.8
10.8
10.7
7.5
8.5
11.2
A
9.8
6.8
9.0
11.2
A
9.3
7.2
10.0
11.1
A
8.3
7.8
10.7
10.4
7.2
10.1
12.7
A
10.5
11.0
12.7
11.0
10.4
8.8
6.8
5.3
3.6
2.4
1.6
4.6
A
A
A
A
A
8.1
11.0
9.9
7.9
9.0
9.3
7.9
8.3
9.6
9.6
9.5
9.7
8.9
8.4
9.1
8.5
6.8
7.8
8.8
7.7
6.2
8.0
8.8
7.7
6.9
8.7
8.8
7.0
7.2
8.8
8.5
6.4
7.4
8.8
8.2
6.7
8.1
8.9
7.6
7.0
8.6
8.6
6.7
8.7
9.7
10.6
11.0
12.0
10.5
11.9
12.6
A
8.6
6.9
9.3
7.4
5.8
6.9
7.5
6.5
5.3
5.3
6.0
5.6
5.5
6.4
6.2
5.5
6.0
6.0
5.1
4.9
5.4
4.9
4.7
4.8
5.0
4.7
4.7
5.2
5.3
4.8
4.9
5.5
5.2
4.8
5.0
5.4
4.9
4.7
5.1
5.4
4.9
4.8
5.2
5.2
4.8
4.8
5.2
4.2
4.7
5.5
5.6
6.3
8.6
9.3
10.2
7.3
8.4
11.9A
10.3
4.9
5.8
6.5
6.9
5.9
5.6
6.2
6.1
5.9
6.7
6.7
5.8
6.2
6.4
5.5
5.2
5.4
5.3
5.0
5.1
5.3
5.1
5.1
5.5
5.7
5.3
5.2
5.6
5.7
5.3
5.1
5.5
5.5
5.1
5.1
5.5
5.3
5.1
5.2
5.5
5.2
5.1
5.2
4.8
4.7
4.8
3.8
4.0
4.7
4.5
4.8
6.1
7.3
8.7
8.3
2.8
7.2
9.6
9.1
8.7
10.4
10.0
8.3
9.2
10.3
10.0
10.3
10.3
8.9
8.9
9.9
8.8
6.8
8.3
9.4
8.0
6.5
8.5
9.4
7.9
7.5
9.4
9.2
7.3
8.4
10.1
9.0
6.8
8.3
9.6
8.2
6.9
8.8
9.4
7.6
7.4
9.2
8.9
6.8
9.2
10.1
7.8
3.5
3.9
5.6
4.8
4.6
5.2
3.9
3.9
4.3
2.4
0.9
0.3
0.2
7.9
A
11.1
10.5
10.2
12.9 A
13.0
10.1
10.5
A
12.0
11.0
11.0
A
12.0
10.0
9.3
A
11.3
10.0
7.2
9.1
A
10.9
8.6
6.0
9.4
A11.0
8.6
7.7
10.8 A 11.0
8.6
10.1
A
13.0
11.7
8.2
9.3
A
11.2
9.4
7.2
9.8
A11.0
8.4
7.7
10.6 A
10.4
7.2
9.9
A
11.8
8.1
3.7
5.1
10.1
10.2
7.6
6.6
5.6
4.4
4.4
3.2
1.6
1.1
0.6
5.8
7.6
8.8
10.8
13.4
13.5
10.6
8.6
8.4
8.4
8.2
8.2
8.0
7.4
7.6
7.2
6.1
6.7
7.2
6.0
4.0
6.4
7.3
6.7
6.2
7.4
8.2
11.0
13.4
12.5
8.7
7.5
7.6
7.1
6.1
7.0
7.5
6.6
6.1
7.3
7.4
6.0
7.2
7.1
6.4
3.9
6.4
11.0
11.3
7.2
9.0
11.0
9.4
5.6
6.4
4.6
3.0
1.9
9.9
A
11.7
9.1
6.0
10.1
10.4
7.0
2.5
2.4
3.0
4.7
8.6
12.5
12.4
8.6
4.9
3.6
3.9
3.8
3.2
3.5
3.6
3.0
2.8
3.2
2.9
2.6
2.3
1.8
2.4
2.6
3.1
3.3
2.9
8.0
3.4
5.4
9.6
A
12.8
11.3
6.9
4.0
3.0
3.0
3.3
2.9
2.7
3.1
3.2
2.8
2.7
3.1
2.4
2.2
2.3
3.2
4.2
6.0
A
8.1
6.3
A
A
1.2
2.2
5.6
9.4
9.6
5.7
2.4
1.4
1.2
1.2
1.0
1.0
1.1
1.0
0.9
0.9
0.9
0.8
0.7
0.5
0.7
0.8
0.9
1.0
1.0
1.5
2.8
6.8
9.8
8.7
4.5
2.0
1.1
1.0
1.0
0.9
0.9
0.9
1.0
0.9
0.9
0.9
0.8
0.8
0.7
1.1
1.5
2.1
3.4
4.8
5.2
6.7
6.7
6.3
10.3
10.7
5.7
0.3
0.4
0.7
1.8
1.0
2.3
2.6
2.3
2.5
3.8
4.2
4.9
6.1
3.8
4.3
4.9
4.3
3.0
2.1
2.2
1.9
2.0
2.1
2.0
10.9
11.4
10.3
6.7
4.8
4.3
2.7
2.1
1.6
1.0
A
12.5
12.8
13.0
11.8
7.4
6.2
7.5
5.5
3.5
10.9
6.4
7.8
11.5
9.8
4.0
3
2
0.8
A
4.7
8.1
11.4
11.3
A
5.3
Downtown Transportation Center - Level 3
Option C - LED footcandle Printout
Luminaire Schedule
Qty Label Description
37
A
BXAL1A028A-U
[MANUFAC]
Watts
BETA LIGHTING, INC_ 54.1
Lumens
3584
5.0
5.6
5.3
7.9
9.9
8.6
3.0
3.0
3.7
4.5
2.1
A
B
D
C
E
F
G
H
J
K
L
M
N
Q
R
S
T
U
1
V
2.4
3.9
3.8
1.1
1.9
2.1
2.1
2.3
2.5
2.5
2.5
2.5
2.3
2.2
2.3
2.2
2.0
2.1
2.2
2.1
2.0
2.2
2.2
2.1
2.1
2.2
2.1
2.0
2.0
2.1
2.1
2.0
2.1
2.2
2.1
2.0
2.1
2.2
2.1
2.0
2.2
2.1
1.9
2.0
2.1
2.1
2.0
1.7
1.5
0.8
2.0
3.4
3.7
3.6
4.0
4.4
4.3
4.4
4.3
3.9
3.7
4.0
3.7
3.3
3.5
3.8
3.6
3.4
3.7
3.9
3.6
3.6
3.9
3.6
3.1
3.4
3.9
3.8
3.4
3.6
3.9
3.6
3.3
3.6
3.8
3.5
3.4
3.8
3.7
3.2
3.5
4.0
3.7
3.4
3.1
2.8
2.5
2.1
1.7
1.1
1.1
2.9
5.2
5.5
4.7
5.4
6.2
5.8
5.9
6.2
5.1
4.9
5.7
5.3
4.2
4.7
5.6
4.9
4.3
5.2
5.6
4.7
4.7
5.7
5.1
3.9
4.3
5.6
5.2
4.2
4.9
5.7
4.8
4.2
5.1
5.6
4.6
4.3
5.4
5.3
4.1
4.9
6.3
5.1
4.9
5.3
4.7
4.2
3.8
2.9
2.3
2.0
1.7
1.2
4.7
6.3
6.4
5.3
6.0
7.0
A
6.4
6.5
6.9
A
5.6
5.3
6.3 A
5.9
4.6
5.2
6.3
A
5.4
4.6
5.8
A6.3
5.1
5.1
6.4 A
5.7
4.2
4.7
6.3 A
5.9
4.6
5.3
6.4
A
5.4
4.5
5.6
A6.3
5.0
4.7
6.0
5.9
4.5
5.3
A
6.9
5.9
6.2
7.0
5.6
5.7
5.9
4.4
3.6
3.7
3.2
2.2
6.5
4.6
4.2
5.8
5.2
3.3
A
A
A
4.5
6.6
A
6.6
5.9
6.6
6.5
5.6
6.1
7.0
6.6
6.6
6.9
5.9
5.5
6.3
5.9
4.9
5.3
6.2
5.5
4.9
5.8
6.3
5.4
5.3
6.3
5.9
4.6
4.9
6.2
6.0
5.0
5.5
6.3
5.6
4.9
5.6
6.2
5.3
5.0
6.0
5.9
4.8
5.6
7.0
6.7
7.3
7.3
5.8
6.4
A
4.3
5.9
6.2
5.9
6.0
5.9
5.6
5.8
6.2
6.2
6.1
6.1
5.6
5.3
5.5
5.3
4.8
5.0
5.4
5.1
4.9
5.3
5.5
5.2
5.1
5.5
5.3
4.7
4.9
5.5
5.5
5.0
5.2
5.5
5.2
4.9
5.2
5.4
5.0
4.9
5.3
5.3
4.7
5.0
5.7
5.9
6.2
6.3
6.1
6.9
6.6
4.6
4.9
6.5 A
5.8
4.1
5.7
6.1
6.1
6.4
6.2
5.8
6.0
6.4
6.2
6.3
6.2
5.6
5.4
5.6
5.3
4.8
5.0
5.5
5.1
4.9
5.3
5.6
5.2
5.2
5.6
5.4
4.8
5.2
5.9
5.7
5.2
5.4
5.7
5.2
4.9
5.3
5.5
5.0
4.9
5.4
5.3
4.7
5.1
5.7
5.3
4.7
4.8
5.3
5.8
5.5
4.8
5.4
6.6
5.5
3.9
4.3
6.3
6.5
6.5
7.6
7.4
6.2
6.6
7.2
6.7
6.8
6.9
5.8
5.5
6.4
5.9
4.8
5.3
6.3
5.5
4.9
5.8
6.3
5.4
5.4
6.5
6.0
5.0
5.7
7.2
6.8
5.5
5.9
6.6
5.6
4.9
5.8
6.3
5.2
5.0
6.0
5.9
4.8
5.6
6.8
5.2
3.8
4.1
5.3
5.6
5.0
4.7
5.0
5.3
4.8
4.9
6.1
4.1
6.3A
6.6
6.9
8.5
8.3
6.6
6.6
7.2
A
6.4
6.5
6.9
A
5.6
5.2
6.2 A
5.8
4.5
5.1
6.1
A
5.1
4.0
5.5
A6.2
5.1
5.1
6.5 A
6.1
5.0
6.2
8.3 A
7.7
5.8
5.9
6.6
A
5.5
4.6
5.6
A6.2
5.0
4.7
5.9
5.9
4.5
5.4
A
6.6
4.8
3.3
4.0
6.3
6.7
5.2
5.0
5.6
5.3
4.6
5.2
6.7
A
A
5.3
3.3
5.6
2.8
A
3.7
5.5
6.1
7.1
9.4
2.6
3.6
4.5
6.0
8.3
9.2
6.8
6.2
6.4
5.8
5.8
6.0
5.1
4.7
5.4
5.1
4.1
4.4
5.1
4.1
2.8
4.5
5.3
4.5
4.6
5.6
5.5
4.9
6.7
9.2
8.2
6.0
4.7
4.4
4.2
4.1
4.1
3.7
3.5
3.6
3.5
3.1
3.1
3.3
2.7
1.9
2.9
3.4
3.3
3.4
3.8
3.9
4.1
5.9
8.3
A
2.1
2.7
4.4
6.5
6.0
5.5
5.8
5.0
4.2
5.0
5.5
4.5
4.2
5.2
5.2
4.1
4.9
5.9
4.5
3.3
4.2
6.4 A
6.3
4.7
5.3
7.2
6.4
5.0
5.6
6.7
4.9
2.4
7.6
5.3
4.2
4.0
3.6
3.3
3.5
3.7
3.4
3.2
3.5
3.5
3.2
3.3
3.6
3.3
3.2
4.2
6.0
5.7
4.5
5.7
A
7.2
5.9
4.6
4.8
5.0
3.9
2.3
6.1
4.0
2.7
2.3
2.1
1.8
1.8
1.9
1.9
1.9
2.0
2.0
1.9
1.9
2.0
2.0
2.5
3.0
4.0
4.6
4.7
5.7
6.6
5.3
4.7
5.0
4.6
3.2
1.3
1.4
1.4
2.5
2.8
4.3
4.4
4.8
4.9
4.6
5.1
6.6
5.6
3.2
3.8
5.4
5.3
5.0
4.6
4.6
5.9
7.3A
5.6
2.8
6.0
7.1
7.0
6.6
5.5
5.5
7.1
7.9
5.4
2.6
6.4 A
7.0
7.1
7.2
5.4
5.4
7.3
7.3
4.9
6.6
4.6
5.0
6.9
6.3
3.5
A
6.5
4.3
3.0
2.7
2.5
2.4
2.3
2.1
2.0
2.0
2.0
1.8
1.8
1.7
1.4
1.0
1.5
1.8
1.9
2.0
2.2
2.4
2.8
4.6
6.6
3
2
1.4
8.5
A
3.5
5.8
6.6
7.1
A
4.8
Downtown Transportation Center - Level 3
Option D - Fluorescent Footcandle Printout
Luminaire Schedule
Qty Label Description
38
A
CHIARO FTW 2328 4
[MANUFAC]
ZUMTOBEL STAFF LIGHTING
Watts
56
Lumens
2950
5.1
4.9
4.1
4.8
6.4
4.8
2.4
3.5
4.1
3.4
1.9
Reset Form
PGL6
Universal Parking Garage Luminaire with Electronic Ballast
revision 4/18/05 • pgl6.pdf
Type:
Job:
Fixture Catalog number:
Fixture
Approvals:
/
/
Electrical Module
See page 3
Optional Features
See page 4
Date:
Page: 1 of 5
Specifications
18" DIA.
(457.2 mm)
4"
(101.6 mm)
10K"
(266.7 mm)
6K"
(165.1 mm)
Fixture with Standard Lexan® SLX Refractor
18" DIA.
(457.2 mm)
4"
(101.6 mm)
11E"
(301.6 mm)
7E"
(200.0 mm)
Fixture with Optional Acrylic Refractor (A)
10" DIA.
(254.0 mm)
4J"
(108.0 mm)
8J"
(209.6 mm)
14E"
(377.8 mm)
LEXAN
16J"
(412.8 mm)
ACRYLIC
Fixture with Optional Balanced Pendant
J-Box and Bird Shroud (PB2)
10L" DIA.
(273.1 mm)
8K" to 13K"
(215.9 mm to 330.2 mm)
Adjustable
Mounting Position
Speed Mount: Electro-zinc plated steel for mounting to standard
4" Junction Box or mud-box. Fixture hangs from hooks to free both
hands to make field wire connections. Allows tool-free fixture
mounting to Junction Box, with integral anti-theft lock.
Electrical Housing: Die-cast, low copper (< 0.6% Cu) aluminum
for direct mounting to the Kim Speed Mount. Wire entries are sealed
by a silicone grommet. Integral latches (2) are die-cast aluminum
with stainless steel springs and stainless steel hangers for the refractor.
Refractor: Standard refractor is one-piece injection molded
non-yellowing Lexan® SLX, .125" minimum wall thickness. Optional
refractor is one-piece injection molded UV stabilized acrylic,
.125" minimum wall thickness. Refractor attaches to electrical
housing with (2) no-tool quick release latches, with one latch
captive as a hinge. Perimeter is fully sealed with a one-piece
extruded silicone gasket, with the ends fused together to form a
continuous piece, sealing the refractor to the electrical housing, and
providing an IP66 fixture rating.
Upper Reflector and Socket: One-piece hydroformed aluminum
with a vacuum metalized reflective finish and protective coating.
Reflector has keyhole slots for no-tool removal from the electrical
housing for ballast access. H.I.D. socket is 4KV pulse rated medium
base. Optional G-12 base socket available for 150PMH lamp mode.
Fluorescent sockets are universal for 26W, 32W, or 42W PL lamps.
Reflector Modules: Die-cast, low copper (< 0.6% Cu) aluminum
with a vacuum metalized reflective finish and protective coating.
Reflectors are attached to the upper reflector, and configured for
up-light, or restricted up-light depending on the specified fixture.
Electrical Components: Electronic H.I.D. ballasts are high power
factor, low frequency, -20°F starting, mounted to a hinged tray as a
self-contained module which includes disconnect plugs for field
wire and socket connections. Fluorescent ballasts are electronic,
high power factor, 0°F starting, mounted on a plate provided with
keyhole slots for attachment to the electrical housing. Induction
Fluorescent lamp / high frequency generator package is high power
factor, -4°F starting, mounted on a plate provided with keyhole slots
for attachment to the electrical housing.
Finish: Standard finish on fixture electrical housing, optional PB2 and
TB2, is white super TGIC powder coat paint applied over a Titanated
Zirconium conversion coating. Consult factory for custom colors.
CAUTION: Fixtures must be grounded in accordance with national,
state and/or local electrical codes. Failure to do so may result in
serious personal injury.
Hubbell
Lighting, Inc.
Fixture with Optional
Trunnion Mount (TB2)
Listings and Ratings
UL cUL 1598
IP66 Rated
© 2005 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695
40C Ambient
ISO 9001:2000
5606405108
PGL6
Universal Parking Garage Luminaire with Electronic Ballast
revision 4/18/05 • pgl6.pdf
Type:
Job:
Page: 2 of 5
Standard Features
Fixture
Cat. No. designates PGL
fixture with full or restricted
uplight.
Cat. Nos. for fixtures available:
PGL61
Series
UP
LIGHT
Full Uplight
Restricted Uplight
PGL61
n/a
PGL62
PGL62R
PGL63
PGL63R
PGL64
PGL64R
n/a
PGL65R
PGL66
PGL66R
PGL67
PGL67R
PGL68
PGL68R
NO INTERNAL
REFLECTORS
DOWN
LIGHT
Driving Direction
PGL62
Series
UP
LIGHT
4 INTERNAL
DOWN-LIGHT
REFLECTORS
DOWN
LIGHT
Driving Direction
PGL63
Series
UP
LIGHT
DOWN
LIGHT
2 INTERNAL
DOWN-LIGHT
REFLECTORS
Driving Direction
PGL64
Series
PGL65
Series
PGL66
Series
UP
LIGHT
DOWN
LIGHT
2 INTERNAL
DOWN-LIGHT
REFLECTORS
Driving
Direction
Driving
Direction
NO UP LIGHT
DOWN
LIGHT
4 INTERNAL
DOWN-LIGHT
REFLECTORS
UP
LIGHT
2 INTERNAL
DOWN-LIGHT
REFLECTORS
With
Houseside
Shield
DOWN
LIGHT
Without
Houseside
Shield
PGL67
Series
One-Way
Driving Direction
UP
LIGHT
DOWN
LIGHT
Garage
Garage
Perimeter
Perimeter
Without
Houseside
Shield
PGL68
Series
2 INTERNAL
DOWN-LIGHT
REFLECTORS
With
Houseside
Shield
UP
LIGHT
DOWN
LIGHT
With Houseside Shield
Driving Direction
Garage
Garage
Perimeter
Perimeter
Driving Direction
2 INTERNAL
DOWN-LIGHT
REFLECTORS
Without Houseside
Shield
© 2005 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695
5606405108
PGL6
Universal Parking Garage Luminaire with Electronic Ballast
revision 4/18/05 • pgl6.pdf
Type:
Job:
Page: 3 of 5
Standard Features
Electrical Module
PMH = Pulse Start
Metal Halide
PL = Compact
Fluorescent
IF = Induction
Fluorescent
Lamp Lamp Line
Watts Type Volts
175 PMH 277
CAUTION: All manufacturers
of metal halide lamps
recommend turning them off
for 15 minutes, once per
week, when under continuous
operation. This will reduce
the risk of arc tube rupture at
end of life. Also, color
temperature may differ
between manufacturers of
metal halide lamps. See lamp
manufacturers’ specification
sheets.
Cat. Nos. for Electrical Modules available:
100PMH120
100PMH208
100PMH240
100PMH277
Lamp ED-17, Clear
Socket Medium Base
ANSI Ballast M-90
Type
4X42PL120
4X42PL208
4X42PL240
4X42PL277
Lamp Coated
Socket GX24q-4 Base
150PMH120
150PMH208
150PMH240
150PMH277
ED-17 Clear
175PMH120
175PMH208
175PMH240
175PMH277
T-6 Clear1
Medium Base G12 Base
M-102
1
ED-17, Clear
Medium Base
M-137
85IF120
85IF208
85IF240
85IF277
85 Watt
Induction
Fluorescent
See Optional Features for - 150PMH - T6 lamp with G12 Base selection.
1
All fixtures are available
pre-lamped by Kim. Consult
representative for pricing.
NOTE: For lamp/ballast
information outside of the
U.S. and Canada, please
consult your local Kim
representative.
© 2005 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695
5606405108
PGL6
Universal Parking Garage Luminaire with Electronic Ballast
revision 4/18/05 • pgl6.pdf
Type:
Job:
Page: 4 of 5
Optional Features
G12 Socket
Cat. No. G12
No Option
Available on 150PMH only.
Optional G12 base socket available for 150 Watt Pulse Start Metal Halide
lamp only, T-6 Bipin configuration. Must use UV filtering lamp.
Standby Lamping
PGL6 Series (electronic ballast)
QS
QUARTZ STANDBY
Integral current sensing relay energizes a T-4 mini-can socket during lamp
warm-up and after power interruption. Socket de-energizes prior to the
H.I.D. lamp reaching full brightness.T-4 mini-can halogen lamp by others;
100 Watt maximum. NOTE: Input amps will increase by .80 with
this option.
Consult factory.
FLS
FLUORESCENT STANDBY
Integral current sensing relay energizes an integral fluorescent ballast during
lamp warm-up and after power interruption. Ballast de-energizes prior to
the H.I.D. lamp reaching full brightness. 22 Watt T-5 circular fluorescent
lamp by others.
Acrylic Refractor
Cat. No. A
No Option
Injection molded UV stabilized acrylic having the same prism design and
optical characteristics as the standard Lexan® SLX . However, the overall
depth is 1K" greater than the standard refractor, and increases the luminaire
efficiency by minimum 5%.
Tamper-Resistant
Latches
Cat. No. TS
No Option
Stainless steel captive hex socket (Allen) shoulder screws secure latches in
locked position.
Fusing
Cat. No.
High temperature fuse holders factory installed inside the fixture housing.
Fuse is included.
(see right)
No Option
Quartz
Standby
Fluorescent
Standby
Acrylic
Refractor
Tamper-Resistant
Latch
Line Volts:
Cat. No.:
120V
SF
208V
DF
240V
DF
© 2005 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695
277V
SF
Single Fuse
5606405108
PGL6
Universal Parking Garage Luminaire with Electronic Ballast
revision 4/18/05 • pgl6.pdf
Type:
Job:
Page: 5 of 5
Optional Features
Balanced Pendant J-Box
and Bird Shroud
Cat. No. PB2
No Option
Die-cast aluminum, finished to match the fixture electrical
housing. Offset L" NPT pendant entry to balance fixture
in free-swinging installation. The Kim Speed Mount
is furnished for fixture attachment to the PB2. This option is
shipped separate from fixture.
Trunnion Mount
Cat. No. TB2
No Option
One-piece cast aluminum fixture mount utilizes the
standard Kim speed mount for fixture attachment, and also
serves as a junction box for field wire connections. Top of
fixture mount casting has K" N.P.T. to receive conduit from
ceiling J-box. (Ceiling J-box and conduit to fixture by
others.) Upper trunnion section is 1K" aluminum bar with
adjustable mounting positions in 1" increments. Suspends
fixture from 8K" to 13K" below the ceiling, as measured to
the fixture top. Finished to match fixture electrical housing.
Lamp Included
Cat. No. Lamp included
No Option
To order fixture with lamp included and installed, add
“Lamp Included” suffix to catalog number. Will also
include QS and FLS lamp when these options are specified.
© 2005 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695
Balanced
Pendant
J-Box
and Bird
Shroud
Trunnion
Mount
5606405108
RSP Series
Round Spectra-Lyte Garage Light
Bulletin No. RSP-080708
Type:
Job:
Catalog Number:
SERIES
Approvals:
-
-
-
DISTRIBUTION VOLTAGE
OPTIONS (FACTORY INSTALLED)
See Page 2
ACCESSORIES (SHIPPED SEPARATELY)
See page 5
Overall Dimensions
FINISH
See Pages 3 and 4
Date:
Page 1 of 6
Specifications
For reference only
Housing / Finish
RSP (HID) with Standard Optical System
Available with either
S (Symmetric) Reflector for HID and CF; or
A (Asymmetric) Reflector for HID only.
15.00”
(38.10cm)
12.38”
(31.43cm)
Die-cast aluminum alloy construction shall ensure durability within parking structures. Standard finish
shall be Textured Satin Aluminum UltraClad™ polyester powder coat, electrostatically applied and
oven cured. Other colors may be specified. Construction and finish of the housing and all exterior
hardware shall ensure fixture is resistant to the effects of corrosives and contaminants such as
exhaust fumes. Easy Hanger Plate and internal component mounting brackets shall be fabricated
from pre-galvanized steel. Standard HID unit constructed to IP54. Standard QL/CF unit is constructed
to IP52. Optional IP65 construction is available (pendant mounting only).
Optical Assembly
4.25”
(10.80cm)
11.75”
(29.85cm)
7.50”
(19.05cm)
Symmetric (S) or Asymmetric (A) Optic Assembly: Enclosed and gasketed optical assembly shall
have an internal reflector system with upper and lower apertures for controlled downlight with uplight
component. Reflector shall also shield the arc tube to sharply restrict discomfort and disabling glare.
Downlight component shall have Type V Round distribution with sharp definition and high peak angles
to give wide spacing and high uniformity while avoiding glare in visual zones. ADL (Additional Downlight)
option available, useful for higher footcandle requirements of entry areas. Upper aperture shall produce
a symmetrical, upward light component that provides fill light on ceiling surfaces. Primary reflector
shall be fabricated from specular, high purity, anodized aluminum that is fixed within lens interior for
proper photometric alignment. Secondary, upper reflector shall be fabricated from specular, high purity,
anodized aluminium and shall redirect high angle light back to the primary reflector and useful beam.
Symmetric Round Refractor (R): For CF source fixtures, Precision Refractor is made from UV
stabilized acrylic, with a Reflector/Refractor option available. With long-life QL lamp sources, a high
impact polycarbonate Refractor is standard.
Symmetric Round Glass Refractor (RG): Glass Refractor available for HID, CF, and QL units.
Lens
12.75”
(32.39cm)
S or A Optics: The injection-molded, UV stabilized, high impact acrylic lens shall be gasketed and
enclosed for optimal performance.
R Optics: An injection-molded, UV stabilized, polycarbonate lens is standard with CF and QL lamp
sources, and is optional on all other wattages (not recommended with 200-175W metal halide lamps).
RG Optics: Molded glass lens may be specified. Suitable for use with HID, CF and QL sources, all
wattages. Ambient temperature restrictions apply. For 200W and below HID, suitable for use in 55°C
(131°F). For 100W and below HID, suitable for use in 65°C (149°F).
Lamp / Socket
The socket shall be porcelain, with spring-pressure center contact, 4KV pulse rated, medium base
HID lamps. Socket shall mount directly to the upper reflector to assure proper photometric alignment
with the optical system. In QL induction units, the lamp and lamp holder are preassembled and integral.
CF unit luminaires utilize T4/PLT4 Compact Fluorescent lamps and GX24q-4/5 sockets.
Ballast
RSP CF/QL with Standard (R) Optical System
Standard for CF and QL.
R (Symmetric Round Refractor).
RG (Symmetric Round Glass Refractor) is
also available for all sources and wattages.
15.0”
(38.10cm)
HID Units: Standard magnetic ballast shall be high power factor with reliable starting at temperatures
as low as -29°C (-20°F) for Metal Halide, -34°C (-30°F) for Pulse Start MH, and -40°C (-40°F) for HPS.
Crest factor does not exceed 1.8. Ballast has Class H, 180°C (356°F) rated insulation system.
Electronic Ballast option: Available for 150-70W Pulse Start Metal Halide units and feature optional
low voltage (0-10v) optional dimming capability.
CF / QL Units: Ballast is high frequency electronic type, with Total Harmonic Distortion of less than 10%
with reliable starting at temperatures as low as -40°C (-40°F) for QL, and -30°C (-22°F) for CF.
Mounting
Standard mounting shall include a galvanized steel Easy Hanger Plate with universal provisions for
4” round and octagonal junction boxes. An external set screw allows the fixture to be locked or removed
without fixture disassembly. Optional tamperproof screws available. Threaded hubs are optional for
pendant mounting to ¾” rigid conduit or direct surface mounting with feed-through wiring. Yoke mount
also available, as well as a wall mount bracket (with or without surface conduit box).
Listings
UL/cUL Listed luminaire, UL 1598, suitable for Wet Locations and 40°C (104°F) ambients. RSPQL-165
watt unit is rated for 25°C ambients. The quality systems of this facility have been registered by UL to
the ISO 9001 Series Standards. RSP-LF option covered by patent 7,121,684.
12.0”
(30.48cm)
Warranty / Terms and Conditions
HID Units: Standard 5 Year Limited Warranty. QL Units: 7 Year Limited Warranty on QL lamp and generator (registration required). CF Units: GE Lighting / ACE Ballast Total Performance OEM Systems
Warranty (registration required). Wide-Lite's current Warranty may be found at www.wide-lite.com (keyword:
warranty) as well as Wide-Lite's current Standard Terms and Conditions of Sale (keyword: terms).
All sales of items in this catalogue shall be subject to Wide-Lite's Standard Terms and Conditions of Sale current at the time of shipment. If you do not have a copy of Wide-Lite's Warranty and Standard Terms, please contact the factory for same prior to ordering.
Hg
Some luminaires use fluorescent or high intesity discharge (HID) lamps that contain small amounts of mercury. Such lamps
are labeled ‘Contain Mercury’ and/or with the symbol ‘Hg’. Lamps that contain mercury must be disposed of in accordance
with local requirements. Information regarding lamp recycle and disposal can be found at www.lamprecycle.org.
Wide-Lite
www.wide-lite.com
CATALOG KEYWORD: RSP
P.O. Box 606 • San Marcos TX 78667-0606
(512) 392-5821 • Fax (512) 753-1122
Specifications and dimensions are subject to change without notice.
Spectra-Lyte series
RSP Series
Round Spectra-Lyte Garage Light
Bulletin No. RSP-080708
Type:
Job:
Page 2 of 6
S Optics Standard for HID,
available for CF
R Optics
Standard
for CF
and QL,
available
for HID
RG Optics Available for all
sources, all
wattages
Series
Distribution
Voltage
Metal Halide
r RSPM-175
r RSPM-100
r S = Symmetric
r 120
r 240
r 208
r 277
Compact
Fluorescent
UV stabilized high impact acrylic lens.
Standard for HID units, also available for CF.
r RSPCF-442
r RSPCF-432
Pulse Start Metal Halide
r RSPP-200
r RSPP-175
r RSPP-150
r RSPP-100
r RSPP-70
High Pressure Sodium
r RSPS-150
(1)
r RSPS-100
r RSPS-70
r RSPCF-426
QL Induction (1)
r QV Quad-Voltage Ballast
r A = Asymmetric
Available for HID sources only.
Allows field selection of
120/208/240/277 voltage.
(No 480V). Certain options may
require voltage selection as well.
UV stabilized high impact acrylic lens.
Available for HID units only.
r RSPCF-242
r R = Symmetric Round Refractor
UV stabilized polycarbonate lens. Standard for
CF and QL units, also available for HID.
Not recommended for use with 200-175 watt MH.
r RSPQL-165
r RSPQL-85
r RG = Symmetric Round Glass Refractor
Borosilicate Glass lens. Available for all sources,
all wattages. Ambient temperature restrictions
apply. See page 1.
Ambient temperature
restrictions apply at certain
voltages. Consult factory.
r 480(2)
r 120-277V
Available for CF and 85W QL.
r 208-277V
Available for 165W QL only.
(2) 480V not available with Electronic
HID ballast option (150-70W
PSMH only).
Distribution Guide & Ballast Data (1)
Source
Type(2)
Catalog
Number
Lamp Reflector
%
.ies
Envelope Type(3) Uplight SP/MH File Name(3)
HPS
Source
Type(2)
CF
Source
Type(2)
QL
ANSI
Code
Line Current (5)
120 / 208 / 240 / 277 / 480
Line LER(6)
Watts standard
S and A
RSPM-175
BT / ED17
S
A
12.3
14.6
5
5.6
rspm17s.ies
rspm17a.ies
CWA
M57 / H39 / M107
1.8 / 1.1 / 0.9 / 0.8 / 0.5
213
53
48
RSPM-100
BT / ED17
S
A
12.3
14.6
5
5.6
rspm10s.ies
rspm10a.ies
HX-HPF
optional CWA
M90 / M140
M90 / M140
2.8 / 1.5 / 1.4 / 1.2 / 0.6
1.1 / NA / NA / 0.5 / NA
130
128
48
60
RSPP-200
BT / ED17
S
A
12.3
14.6
5
5.6
rspp20s.ies
rspp20a.ies
CWA
M136
2.2 / 1.3 / 1.1 / 1.0 / 0.5
232
50
45
RSPP-175
BT / ED17
S
A
12.3
14.6
5
5.6
rspp17s.ies
rspp17a.ies
CWA
M137 / M152
2.0 / 1.1 / 0.9 / 0.8 / 0.5
220
48
44
RSPP-150
BT / ED17
S
A
12.3
14.6
5
5.6
rspp15s.ies
rspp15a.ies
HX-HPF
M102 / M142
optional CWA
M102 / M142
optional Electronic M102 / M142
3.7 / 2.1 / 1.8 / 1.6 / 1.0
1.7 / NA / NA / 0.8 / NA
1.4 / 0.8 / 0.7 / 0.6 / NA
185
189
166
41
37
RSPP-100
BT / ED17
S
A
12.3
14.6
5
5.6
rspp10s.ies
rspp10a.ies
HX-HPF
M90 / M140
optional CWA
M90 / M140
optional Electronic M90 / M140
2.8 / 1.4 / 1.4 / 1.2 / 0.6
1.1 / NA / NA / 0.5 / NA
0.9 / 0.5 / 0.5 / 0.4 / NA
130
128
113
__
__
RSPP-70
BT / ED17
S
A
12.3
14.6
5
5.6
rspp70s.ies
rspp70a.ies
HX-HPF
M98 / M143
optional Electronic M98 / M143
1.9 / 1.0 / 0.9 / 0.8 / 0.5
0.7 / 0.4 / 0.3 / 0.3 / NA
95
78
63
57
RSPS-150
BT / ED17
S
A
21.9
15.0
6
6.5
rsps15s.ies
rsps15a.ies
HX-HPF
optional CWA
S55
S55
3.2 / 1.7 / 1.6 / 1.4 / 0.7
1.7 / NA / 0.9 / 0.7 / 0.5
195
190
62
55
RSPS-100
BT / ED17
S
A
21.9
15.0
6
6.5
rsps10s.ies
rsps10a.ies
HX-HPF
optional CWA
S54
S54
2.3 / 1.4 / 1.1 / 1.0 / 0.8
1.2 / NA / 0.7 / 0.5 / 0.3
130
138
54
48
RSPS-70
BT / ED17
S
A
21.9
15.0
6
6.5
rsps70s.ies
rsps70a.ies
HX-HPF
S62
1.7 / 1.0 / 0.9 / 0.8 / 0.6
94
49
44
MH
PS
Ballast
Type(4)
Catalog
Number
Lamping
Spacing
Criteria
Min.
Starting
Max.
Ambient(9)
Lamp
Life
.ies
File Name(3)
Line Current
120 / 220-240 / 277
Line
Watts
LER(6)
RSPCF-442
4X42W CF
2.1
-30°C
40°C
15,000
rspc442(*).ies
1.5 / 0.8 / 0.6
168
65
RSPCF-432
4X32W CF
2.1
-30°C
40°C
15,000
rspc432(*).ies
1.0 / 0.5 / 0.4
128
64
RSPCF-426
4X26W CF
2.1
-30°C
40°C
15,000
rspc426(*).ies
0.9 / 0.5 / 0.4
104
59
RSPCF-242
2X42W CF
2.0
-30°C
40°C
15,000
rspc242(*).ies
0.7 / 0.4 / 0.3
90
63
Catalog
Number
Lamping(8)
Spacing
Criteria
Min.
Starting
Max.
Ambient(9)
Lamp
Life(10)
.ies
File Name(3)
Line Current
120 / 208 / 240 / 277
Line
Watts
LER(6)
RSPQL-165(7)
165W QL
1.6
-40°C
25°C
100,000
rspq165r.ies
N/A / 0.8 / 0.7 / 0.6
165
63
RSPQL-85
85W QL
1.6
-40°C
30°C
100,000
rspq85r.ies
0.8 / 0.5 / 0.4 / 0.3
85
62
Distribution Guide and Ballast Data Notes:
(1) The RSP Series (Round Spectra-Lyte Garage Luminaire) can accommodate a variety of
other wattages and lamps. Please consult factory with specific requirements.
(2) MH = Metal Halide, PS = Pulse Start Metal Halide, HPS = High Pressure Sodium. CF =
Compact Fluorescent, QL = QL Induction. Clear lamps are recommended for optimum
uniformity. CF and QL source available with coated lamp only.
(3) Standard HID reflector types: S = Symmetric, A = Asymmetric. Standard CF and QL reflector
type: R = Symmetric Round Refractor. S reflector available with CF source. Replace (*) with
chosen CF Reflector Type. To specify R reflector with HID source, consult factory.
(4) CWA = Constant Wattage Autotransformer, HX-HPF = High Reactance High Power Factor.
Consult factory for other HID ballast types and additional CF and QL information.
(5)
208V, 240V, 480V and QV units available. Consult factory to confirm availability and line
current information.
(6) LER = Luminaire Efficacy Rating. Calculated in accordance wtih NEMA Standard LE-5B.
For PSMH 150-70W LER values with optional Electronic or CWA ballast, consult factory.
(7) Ambient temperature restrictions apply at certain voltages. Consult factory.
(8) Data represents highest and/or most common lumen packages available for each reflector
size. Please note Maximum Ambient temperature. Consult factory for additional information
on specific lamping requirements.
(9) Important: Ambient temperature guidelines must be followed. Operation in excess of
Maximum Ambient temperatures will void luminaire warranty. Approximate °C to °F
relationship is as follows: 25°C = 77°F, 30°C = 86°F, 40°C = 104°F.
(10) Lamp life based on 50% mortality rate at 10 hour starts.
Wide-Lite
www.wide-lite.com
CATALOG KEYWORD: RSP
P.O. Box 606 • San Marcos TX 78667-0606
(512) 392-5821 • Fax (512) 753-1122
Specifications and dimensions are subject to change without notice.
Spectra-Lyte series
RSP Series
Round Spectra-Lyte Garage Light
Bulletin No. RSP-080708
Type:
Job:
Page 3 of 6
Options (factory installed)
r E = Electronic Ballast option Use this option when a specific manufacturer’s ballast is not known or not required. Wide-Lite will select a ballast that
is appropriate for the application. Consult factory if a specific ballast manufacturer below is selected to assure compatibility.
Electronic ballast available RSP wattages:
150W , 100W , 70W PSMH only
Available Voltages:
120V 208V 240V 277V
r E2 = Universal E-tensityTM
Leave blank to specify electronic ballast without
dimming capability.
r E5 = Ace
Useful in meeting 50 fc minimum entry zone requirements of parking garages.
r ADL = Additional Down Light
Modified upper reflector focuses more light downward.
Note: Available for HID only.
r
r D50 = optional Electronic Ballast Dimming
to 50% power (0-10v)
r E1 = Metrolight SuperHIDTM
BL = Bi-Level ®
Bi-Level provides high/low level of lamp output
with 50% power consumption. Zero crossover
network avoids strobing and lamp dropout.
Note: Available for HID only. Bi-level dimming is suitable for
HPS in all wattages. Metal halide dimming below 100W is not
recommended due to noticeable color shift. Consult factory.
For preventing damage to the ballast at PSMH and HPS lamp end-of-life.
r ITS = Ignitor Turn-Off Switch
Disconnects ignitor within seven minutes if a lamp has failed. See also Wide-Lite
Technical Bulletin: Operating Cautions for All Products Using HID lamps.
Note: Available for PSMH and HPS units only.
Auxiliary / Emergency Lighting (for HID only)
Photometric Data Comparison Reveals Uniformity of Light with T5HO Circline
Auxiliary / Emergency Lighting System. (Garage lighting application viewed from
above showing relative footcandle levels on the floor and surrounding walls.)
Quartz Emergency Lamp in
RSP with T5HO Circline
typical Garage Fixture
Fluorescent Lamp
LiteMatic Operation (LQ = LiteMatic Quartz, LF = LiteMatic Fluorescent)
Normal Start:
RSP-LF
options
covered by
Patent
7,121,684.
LOW
HIGH
Main HID and
auxiliary (T5HO
Circline Fluorescent
or Quartz) lamps
both energized.
Main Lamp Reaches
Approximately 40%of
Rated Output:
Auxiliary (Fluorescent or
Quartz) lamp automatically
extinguishes.
Combined lamp currents
never exceed that of main
lamp at 100% output.
Main Lamp
Reaches
Approximately
40%of Rated
Output:
When Arc
Extinguished:
After power interruption,
auxiliary (Fluorescent or
Quartz) lamp is
automatically energized
when power is restored
and remains on during
run down, restrike and
ramp up.
Auxiliary (Fluorescent
or Quartz) lamp
automatically
extinguishes.
Fluorescent auxiliary lamp offers a high performance alternative to traditional quartz restrike systems. Advantages include 16,000 hr lamp life,
3800 lumens (55W), cooler operation resulting in safer lamp handling, and precise, round distribution for optimum photometric performance.
Auxiliary Fluorescent Systems
r CSRLF = Hot 55W HO Circline Restrike
r LF = Hot/Cold 55W HO Circline Auxiliary Lighting
System with Lamp
r LF1 (XXX) = Circline Auxiliary Lighting System
XXX = Specify voltage. Requires an Interlock (by
others) to ensure HID and fluorescent source are not
operated at once. (XXX component of order sequence to
be manually entered in part number on page 1 after Option is
selected).
Note: LF1-EBB and LF-EBB are not available
with TW2 feed-through luminaire wiring.
r LF1-EBB = Circline Auxiliary Lighting System
with Emergency Battery Backup
r LF-EBB = Hot/Cold 55W HO Circline Emergency
Lighting System with Emergency Battery Backup
Auxiliary Quartz Systems
r CSR = Hot Quartz Restrike
r LQ = Hot/Cold Quartz Restrike 100 watt quartz lamp
r LQ1 = Separately Wired (120V) Quartz Restrike
Note: (Requires 5-wire) 100 watt quartz lamp
r LQ2 = LQ and LQ1 combined in the same fixture
Note: Standard 100 watt (120V) double contact bayonet base socket.
Combined Quartz wattage may not exceed HID lamp wattage.
Note: (Requires 5-wire). LQ1 and LQ2 require an Interlock (by others)
to ensure HID and Quartz source are not operated at once.
Note: RSP-LF options are not available with RG optics or with 200W Pulse Start.
CSRLF: Circline Fluorescent restrike using a current sensing relay.
Activation: At cold start / restrike, through Run Down. Extinquishes once main HID
lamp strikes / restrikes.
LF: Provides LiteMatic T5HO Circline Fluorescent auxiliary operation for fixtures
with 120V or multi-tap ballasts. Activation: At cold start / restrike, through run down,
restrike and ramp up. Extinquishes after lamp reaches approximately 40% light output.
LF1: Separately wired, externally controlled Circline Fluorescent Emergency
Lighting from an auxiliary power source (generator, inverter, UPS). Activation:
Emergency (Black Out) conditions only. Extinquishes when main power is restored.
LF1-EBB: Provides factory supplied, externally mounted Emergency Battery
Backup (EBB) to power the circline fluorescent lamp. Activation: Emergency
(Black Out) conditions only. Extinquishes when main power is restored.
LF-EBB: Provides LiteMatic Circline Fluorescent auxiliary operation and
includes factory supplied, externally mounted Emergency Battery Backup
(EBB) to power the circular lamp. Activation: At cold start / restrike, through run
down, restrike and ramp up. Extinquishes after HID lamp reaches approximately 40%
light output.
CSR: Quartz restrike using a current sensing relay. Activation: At cold start /
restrike, through Run Down. Extinquishes once main HID lamp strikes / restrikes.
LQ: Provides LiteMatic Quartz auxiliary operation for fixtures with 120V
or multi-tap ballasts. Activation: At cold start / restrike, through run down, restrike
and ramp up. Extinquishes after HID lamp reaches approximately 40% light output.
LQ1: Separately wired, externally controlled Quartz Emergency Lighting
from an auxiliary power source (generator, inverter, UPS).
Activation: Emergency (Black Out) conditions only.
Extinquishes when main power is restored.
LQ2: Combines the standard LQ and LQ1 systems to provide
the ultimate in safety and security. Activation: At cold start /
restrike, through run down, restrike and ramp up. Extinquishes after
HID lamp reaches approximately 40% light output. Emergency
(Black Out) conditions only. Extinquishes when main power is restored.
Wide-Lite
www.wide-lite.com
CATALOG KEYWORD: RSP
AUXILIARY
POWER
SOURCE
P.O. Box 606 • San Marcos TX 78667-0606
(512) 392-5821 • Fax (512) 753-1122
Specifications and dimensions are subject to change without notice.
AUXILIARY
POWER
SOURCE
Spectra-Lyte series
RSP Series
Round Spectra-Lyte Garage Light
Bulletin No. RSP-080708
Type:
Job:
Page 4 of 6
Options (factory installed)
r F1 = Single Fuse (120V/277V)
r F2 = Double Fuse (208V/240V/480V)
r IP65 = Dust-Tite Construction
Standard unit consists of 1 or 2 KTK 30 amp
fuses mounted internally on the ballast plate.
May be specified with standard junction box (by others) when unit is pendant
mounted (PND-RC, PND-RC-24-LDS, or PND-OJB) or with direct surface
mounting and feed-thru wiring (TW2).
IP65 option with standard easy hanger plate mounting requires the use of
weatherproof wiring connectors or weatherproof junction box (by others).
r PND-RC = Pendant Mounting
(for mounting to Rigid Conduit)
r PND-RC-24LDS = Same as PND-RC
with 24” leads
3/4” threaded hub allows mounting to rigid pendant
lengths up to 12”. (Junction Box by others)
Standard supply wiring connection for PND-RC is made
inside fixture and requires removal of lens and reflector pan.
For external wiring to ceiling mounted
junction box, specify PND-RC-24LDS.
r PND-OJB = Pendant Mounting / Offset
Junction Box
3/4” threaded hub allows mounting
to free swinging or rigid pendant
lengths greater than 12”.
r TW2 = Thru-Wire Provision
Note: Not available in conjuction with
EBB or LF-EBB options.
Feed-thru wiring for direct surface mounting
to 3/4” conduit.
r BP = Bulk Packed Easy Hanger Plate
For job site installation convenience prior to scheduled fixture arrival.
r TS = Tamper Resistant Screws
Provides an additional level of security by inhibiting unauthorized access.
r VL = Polycarbonate Lens
Standard on RSPQL.
Not available for HID sources.
Impact resistant polycarbonate lens is less prone to vandalism.
Polycarbonate lens is covered by a 1 year factory warranty.
r NLMP = No Lamp
Specified if lamps are to be provided by others. Not available for RSPQL.
r 50HZ = 50 Hz Ballast Operation
Specified for applications (outside the U.S) where 50 Hz operation is standard.
r CWA = Low Wattage CWA Ballast
Provides improved voltage regulation and reduces current draw. Available
for 150W and 100W only.
r Y = Yoke Mount
Specified as an alternative to pendant mounting,
especially for sloped ceilings.
Yoke provides rigidity as well as adjustable mounting
height and routing of SO cord (not included).
Wide-Lite
www.wide-lite.com
CATALOG KEYWORD: RSP
Spectra-Lyte series
P.O. Box 606 • San Marcos TX 78667-0606
(512) 392-5821 • Fax (512) 753-1122
Specifications and dimensions are subject to change without notice.
RSP Series
Round Spectra-Lyte Garage Light
Bulletin No. RSP-080708
Type:
Job:
Page 5 of 6
CF/QL Exclusive Options (factory installed)
r LMP(XX) = Lamped (Standard)
XX = Specify Lamp Color Temperature
(XX component of order sequence to be manually entered in part
number on page 1 after Option is selected. See chart)
27 = 27K (2700 Lamp, CF only)
30 = 30K (3000K Lamp, CF or QL)
35 = 35K (3500K Lamp, CF only)
40 = 40K (4000K Lamp, QL(1))
41 = 41K (4100K Lamp, CF only (2))
(1) If Lamp Color Temperature is not specified with this option, RSPQL is shipped with 40K lamps.
(2) If Lamp Color Temperature is not specified with this option, RSPCF is shipped with 41K lamps. CF
Lamps shipped separately.
r SL = Switch Legs (CF only)
Provides energy savings by allowing selective operation of each of the 2
electronic ballasts.
r ZX = Locking Sockets (42W & below CF only)
Ensures compact fluorescent lamps will remain securely in the socket.
Especially useful in areas that experience elevated levels of vibration.
Note: EBB options are not available with TW2
feed-through luminaire wiring.
For CF only. Remotely
mounted emergency battery
backup, suitable for Damp
Locations. Includes two 24”
Note: Ambient temperature restrictions apply at certain
voltages, consult factory.
r EBB-DL-750-(XXX)-MT = Emergency Battery Backup,
Standard Remote Mount, 750 Lumens, Manual Test Switch
r EBB-DL-1000-(XXX)-MT = Emergency Battery Backup,
Standard Remote Mount, 1000 Lumens, Manual Test Switch
r EBB-DL-1000-(XXX)-ST = Emergency Battery Backup,
Standard Remote Mount, 1000 Lumens, Self Test Switch
XXX = Specify voltage (120 or 277 only)
(XXX component of order sequence to be manually entered in
part number on page 1 after option is selected.)
Luminaire
AC power
in
EBB
AC power
in
sections of 3/8” flex conduit,
charging indicator light,
and a manual test switch.
(Self test switch available
on 1000 Lumen unit only.)
Mounting dimensions
depend on ballast type. Consult
factory.
Remote Mount
Emergency
Battery Backup
Finish
r TSA = Textured Satin Aluminum (Standard)
r TGN = Textured Green
r TDB = Textured Dark Bronze
r TGR = Textured Gray
r TBK = Textured Black
r TWHT = Textured White
r RAL(*) = Special Tiger DryLac®
Powder coat finish
(*) Specify RAL color number from
RAL color chart (Consult factory)
Accessories (field installed - shipped separately)
r WMB-RSP-NM-(X) = Wall mount bracket to
Recessed Wiring Box (by others). (X) = Finish
WMB-RSP-NM
Requires PNDRC option.
r WMB-RSP-NM-SCB-(X) = Wall mount bracket
with Surface Conduit Box. (X) = Finish
Requires PNDRC option.
r WMB-RSP-PNDRC-(X) = Wall mount bracket for
Pendant Mounting (pendant length less than 12”;
conduit by others). (X) = Finish
Requires PNDRC option.
r WMB-RSP-PNDRC-SCB-(X) = Wall mount bracket
with Surface Conduit Box for Pendant Mounting
(pendant length less than 12”; conduit by others).
(X) = Finish Requires PNDRC option.
See page 6 for
details on other
WMB-RSP
wall mount
bracket
accessories
and alternate
mounting
methods
r WMB-RSP-EZM-(X) = Wall mount bracket for
Pendant Mounting (pendant length greater than
12”; conduit by others). (X) = Finish
Requires PND-OJB option.
r WMB-RSP-EZM-SCB-(X) = Wall mount bracket
with Surface Conduit Box for Pendant Mounting
(pendant length greater than 12”; conduit by others).
(X) = Finish Requires PND-OJB option.
Wide-Lite
www.wide-lite.com
CATALOG KEYWORD: RSP
P.O. Box 606 • San Marcos TX 78667-0606
(512) 392-5821 • Fax (512) 753-1122
Specifications and dimensions are subject to change without notice.
Spectra-Lyte series
RSP Series
Round Spectra-Lyte Garage Light
Bulletin No. RSP-080708
Type:
Job:
Page 6 of 6
Accessories (field installed - shipped separately)
additional RSP wall brackets and alternate mounting details (order on page 5)
WMB-RSP-SCB
WMB-RSP-PNDRC
also available with surface conduit box
WMB-RSP-EZM
also available with surface conduit box
see detail
below
WMB-RSP-SCB
surface conduit
box detail
3.63”
(9.21cm)
11/32” dia.
thru hole
(4 places)
supplied with
wall bracket
3.63”
(9.21cm)
3/4” NPT
threaded
conduit hub
Bolt pattern for
WMB-RSP
RSP Wall Mount
bracket mounted
directly to wall
(recessed wiring
box by others)
mounts to surface conduit box
or recessed wiring box
2.5”
(6.35cm)
square
mounts with
(4) 1/4”
fasteners by
others)
(5 places)
mounts to adapter plate
with 3/4” NPT nipple
r IF1 = Single Inline Fusing (120V/277V)
r IF2 = Double Inline Fusing (208V/240V/480V)
Consists of 1 or 2 fuse holders and 1 or 2
KTK 30 amp fuses.
r HSS = House Side Shield
For use with “S” HID optics only.
Restricts spill light onto adjacent areas.
r T2S = Type 2 Shield
Type II Asymmetric Shield. Supplemental reflector converts the distribution to
an elliptical rather than a concentric pattern.
r BG = Bird Guard
Inhibits nesting which may
cause overheating of
fixture.
Pendant mounting required.
Available in Satin Aluminum only.
Notes
Wide-Lite
www.wide-lite.com
CATALOG KEYWORD: RSP
P.O. Box 606 • San Marcos TX 78667-0606
(512) 392-5821 • Fax (512) 753-1122
Specifications and dimensions are subject to change without notice.
Spectra-Lyte series
The Edge™ LED Parking Structure Light
BLD-PKG-PS-DM
Beta Catalog Number: BLD - PKG -
- DM -
- LED-B -
-
Rev. Date: 08/28/08
-
Reset
Nickel-Chrome
Anti-Fouling
Wire Guard
6.0"
(152 mm)
Notes:
11.17"
(284 mm)
17.0"
(432 mm)
Product
Family
BLD
Housing
Indicator Optics
PKG
PS1
PSL2
Initial Delivered LED
Mounting Lumens (00’s)
Performance
LED-B
DM3
034
051
068
085
Voltage
UL
(120–277V
Universal)
12
27
34
Color
Factory-Installed Options
more than one option, please type
Options Ifin choosing
manually on the lines provided above.
SV
BZ
BK
WH
PB
F–Fuse
HL–Hi/Low (175/350/525, dual circuit input)4-7
P–Photocell5
TL–2-Level (175/525 w/ integrated sensor control)6,7
TL1–2-Level (350/700 w/ integrated sensor control)6,7
TL2–2-Level (0/350 w/ integrated sensor control)6-8
TL3–2-Level (0/525 w/ integrated sensor control)6,7
TL4–2-Level (0/700 w/ integrated sensor control)6,7
35K–3500k Color Temperature9
43K–4300k Color Temperature9
525–525mA Drive Current10
Footnotes
1-Petroleum symmetric distribution
2-Petroleum symmetric distribution with cutoff shield (louver)
3-Direct mount
4-Sensor not included
Output Multipliers
Color
Temperature
6000K (Standard)
4300K
3500K
Lumen
Multiplier
1.00
0.80
0.75
Ambient
Temperature (ºC)
-20
10
25
40
Lumen
Multiplier
1.11
1.04
1.00
0.96
5-Must specify voltage other than UL
6-Refer to multi level spec sheet for more information
7-Available for 2-5 light bar fixtures
8-May be ordered with 525mA drive current
9-Color temperature per fixture
10-Driver operates at 525mA instead of the standard 350mA
providing a higher lumen output and a shorter life
11-Uses five light bar size with blanks used in place of light
bars
LED Performance Generation B Specs*
Initial
Initial
System
System
Light Delivered Lumens – Delivered Lumens –
Watts
Watts
Bars
PS Optic
PS Optic w/ Louver 120-277V 347-480V
3,840 (034)
2,480 (034)
55
59
211
Drive
Lumen
Power
L70 Life* @ L70 Life* @ L70 Life* @
5,760 (051)
3,720 (051)
79
84
311
Current Multiplier Multiplier 15ºC (hours) 0ºC (hours) -20ºC (hours)
7,680 (068)
4,960 (068)
104
109
411
175mA
0.60
0.5
> 150,000
> 150,000
> 150,000
5
9,600 (085)
6,200 (085)
128
133
350mA
1.00
1.0
> 150,000
> 150,000
> 150,000
* Based on 6000k color temperature fixture operating at 350mA and 25C Ambient.
(Standard)
525mA
1.30
1.5
70,000
110,000
> 150,000
700mA
1.55
2.1
50,000
70,000
115,000
* Refer to LED Ambient spec sheet.
Beta LED
•
1200 92nd Street
•
Sturtevant, WI 53177
•
800-236-6800
•
www.BetaLED.com
TM
The Edge™ LED Parking Structure Light
BLD-PKG-PS-DM
Rev. Date: 08/28/08
General Description
Finish
Slim, low profile design. Fixture is constructed from rugged extruded
aluminum and stamped metal components. LED driver is mounted in
extruded aluminum fixture ends and sealed for weather-tight operation. High
performance aluminum heatsinks specifically designed for LED parking
structure application. Nickel-chrome plated wire guard provides anti-fouling
protection from leaf/debris and animal nesting to assure cool LED operation.
Mount bracket designed to mount directly over existing single gang and
octagonal junction boxes for Direct Mount. Five year limited warranty on
fixture.
Exclusive Colorfast DeltaGuard® finish features an E-Coat epoxy primer
with an ultra-durable silver powder topcoat, providing excellent resistance to
corrosion, ultraviolet degradation and abrasion. Bronze, black, white and
platinum bronze powder topcoats are also available. The finish is covered by
our 10 year limited warranty.
Electrical
Patents
Modular design accommodates varied lighting output from high brightness,
white, 6000K (+/- 500k per full fixture), minimum 75 CRI, long life LED
sources. 120-277V 50/60 Hz, Class 1 LED drivers are standard. 347-480V
50/60 Hz driver is optional. LED drivers have power factor >90% and THD
<20% of full load.
Labels
UL listed in the U.S. and Canada for wet locations and enclosure classified
IP66 per IEC 529. Fixture also available with CE listing. RoHS compliant.
US and international patents pending. Design patents/regs. granted and
pending. German 000819743-0002, Australian 318228.
Field-Installed Accessories
150°
Vertical
3926
15'
5234
Horizontal
Independent Testing
120° Laboratories certified test.
Report No. ITL 60663.
Candlepower distribution
curve of 6 light bar
luminaire with 11,520 initial
90° delivered lumens operating
at 350mA.
2617
1309
90°
10'
5'
0'
5'
10'
15'
15'
4.6
10'
3.0
5'
1.5
0'
0m
5'
Isofootcandle plot of 6 light
bar Petroleum Symmetric
optic LED luminaire at 15'
A.F.G. Luminaire with
11,520 initial delivered
lumens operating at 350mA.
Initial FC at grade.
1.5
15
60°
60°
10
10'
3.0
5
15'
0°
30°
TM
Beta LED
30°
•
1200 92nd Street
•
4.6
Sturtevant, WI 53177
3.0
1.5
•
0m
1.5
800-236-6800
3.0
•
4.6
4.6
www.BetaLED.com
CHIARO Surface-Mounted or Suspended Moisture-Proof Diffuser Luminaire 4’
• Durable, moisture-proof
luminaire is ideal for humid or
dusty locations
• Housing is transparent,
high-impact resistant
polycarbonate with
polyurethane gasketing
• Perforated white reflector
allows 20% indirect component
• One-piece, injection molded
polycarbonate diffuser is
impact resistant and easy to
clean
Fluorescent Two Lamp, T5, T5 HO or T8
• The diffuser's computeroptimized prismatic structure
offers excellent glare control
and high efficiency
• Diffuser unscrews for access to
lamps
• May be suspended or surfacemounted; mounting kits
ordered separately
Cross Section
157.5°
900
135.0°
600
112.5°
300
90.0°
300
67.5°
600
282
online
Find it Fast
180.0°
1200
45.0°
900
1200
0.0°
Side View
22.5°
2 1/8"
4 9/16"
7 11/16"
50 3/16"
Ordering Note: Specify lapming, length, voltage, mounting and options.
▼Fixture
FTW
FTW CHIARO FT, Wide
▼Lamping
▼Length
______
__
2285 (2) 28W T5
2328 (2) 32W T8
2545 (2) 54W T5 HO
4
4'
▼Voltage
______
UNV Universal 120-277V
▼Mounting
▼Options
______
______
SM Surface Mounting Kit
SK 20" Suspension Kit, includes feed cord
1 Stand-By Battery Pack
TF Transparent diffuser fasteners
AV Tamper-proof fastener kit