Specifications Sheet
CSI9360
June 2014
Vibration/Position Transmitter
Emerson’s versatile 4-20mA loop powered eddy current sensor transmitter is
field configurable for any of three vibration ranges or a position measurement with
selectable polarity. The transmitter has two selectable loop signal response times
and two selectable sensor fault latch times. The transmitter’s three sensor excitation
frequencies allow three sensors to be very closely spaced for 2oo3 measurements in
limited space measurement areas.
Measurement Performance
Channels/Output
1 – Vibration or Position (Jumper)
Vibration Measurement Ranges
3 – Ranges (Jumper)
PR6422 Sensor (5mm):
25/62.5/125 μm ±4% ISF
Vibration
Position
PR6423 Sensor (8mm):
Vibration
Position
1.0 mm FSR ±2% DSL
50/125/250 μm ±4% ISF
2.0 mm FSR ±2% DSL
Values Include Sensor Exchange Error and Assume Same Cable
ISF = Incremental Scale Factor
DSL = Deviation from Straight Line
FSR = Full Scale Range
Position Signal Inversion
Selectable (Jumper)
Signal Response Time
100 ms or 1.0 s (Jumper)
Fault Indication (Red LED)
Fault Latch and Release:
Output ≤ 3.6 mA, Response Time <5ms
100 ms or 2.0 s (Jumper)
Maximum Sensor Cable Length
10 m (32.8’)
Sensor Excitation Frequencies
3 (Jumper, see Order Matrix)
Environmental
Shock Limit
15 g pk (147.1 m/s2)
Temperature Range
-35 to 75°C (-31 to 167°F)
Sealing
IP20
Agency Ratings
CE
Available August 2014 est.
CSA Class 1, Div 2 (Group A, B, C, D, T4)
Available August 2014 est.
ATEX Zone 2 (Ex 3G IIC T4)
Mechanical
Case Material / Weight
Die Cast Zinc / 420 g (14.8 oz)
Mounting
DIN Spring Clip, Optional Panel Adaptor
www.assetweb.com
Specifications Sheet
CSI9360
June 2014
Electrical
Connection
Current Loop:
Supply Voltage
Maximum Voltage at Terminals
Over Voltage Protection
Nominal Output Range
Buffered Out:
Connection
Voltage Range
Output Impedance / Nominal Load
Pins 1&2 (Screw Terminal)
Nominal 24 VDC, 250 Ohm – Shunt
20 to 32 VDC (3.6mA); 12 to 32 VDC
(20mA)
50 VDC maximum
4 to 20 mA
SMB and/or Pins 3&4 (Screw Terminal)
0.8 to 4.0 VDC
10 kOhm / 10 mOhm
CSI 9360 Order Matrix
A9360 / XX -XX
Eddy Current Sensor Tip Size
05=5 mm, 08=8 mm
Total Cable length
05=5 m, 09=9 m
-X
X
XX
XX
Factory Setup*
Measurement Type
Sensor Oscillation Frequency
0= Vibration, maximum range (Default)
1= Vibration, medium range
2= Vibration, short range
3= Position
0 (Default)
1
2
X
X
*Jumper Selectable Settings: Measurement Type and Sensor Oscillation Frequency are jumper selectable settings. While able to be changed in the field, Measurement Type is offered as an ordering convenience
for customers that would prefer Emerson to set the jumper. Because the oscillation frequency jumper can affect the measurement accuracy by approximately 3%, Emerson recommends this jumper be pre-set by
the factory. Please refer to the user manual for considerations when making any changes to the jumper selections.
Page 2
Specifications Sheet
CSI9360
June 2014
Sensor Ordering Information
5mm Eddy Current Sensor
PR6422 /
Eddy Current Sensor Sleeve Size
0=M6x0.5, 1=¼-28UNF-2A
Armored Cable
0=WITHOUT, 1=WITH
Total Sensor Length C=Cx+5.3mm
0(Cx=20 mm), 1(30 mm), 2(40 mm), 3(50 mm),
4(60 mm), 5(70 mm), 6(80 mm), 7(90 mm), 8(100 mm)
Adapter Plug
0=WITH , 1=WITHOUT
Total Cable Length
1(5 m), F(9 m)
8mm Eddy Current Sensor
X
X
X
-X
X
2
X
X
X
X
X
PR6423 /
Eddy Current Sensor Sleeve Size
0=M10x1, 1=3/8-24UNF-2A
Armored Cable
0=WITHOUT, 1=WITH
Total Sensor Length C=Cx +9mm
0(Cx=25 mm), 1(35 mm), 2(45 mm), 3(55 mm),
4(65 mm), 5(75 mm), 6(85 mm), 7(95 mm),
8(105 mm), 9(115 mm)
Adapter Plug
0=WITH , 1=WITHOUT
Total Cable Length
1(5 m), F(9 m)
Typical CSI 9360 model number:
Typical sensor model number:
A9360/08-05-00
PR6423/002-112
X
X
X
-X
X
2
X
X
X
X
X
Typical model number for CSI 9360 shown here indicates use with an 8 mm Eddy current sensor tip and 5 m cable, with
maximum vibration range and default oscillation frequency settings.
Typical sensor model number shown here indicates an 8 mmx45 mm sleeve with M10x1 threading, without armor, and with a
5 m cable consisting of a 1m pigtail and adapter. The 2 at the end of the model string represents the size 00 LEMO connector
which connects the sensor cable to the CSI 9360.
©2014, Emerson Process Management.
Emerson Process Management
Reliability Solutions
835 Innovation Drive
Knoxville, TN 37932
T (865) 675-2400
www.assetweb.com
The contents of this publication are presented for informational purposes only, and while every
effort has been made to ensure their accuracy, they are not to be construed as warranties or
guarantees, express or implied, regarding the products or services described herein or their use or
applicability. All sales are governed by our terms and conditions, which are available on request.
We reserve the right to modify or improve the designs or specifications of our products at any
time without notice.
All rights reserved. Machinery Health is a mark of one of the Emerson Process Management group
of companies. The Emerson logo is a trademark and service mark of Emerson Electric Co. All other
marks are the property of their respective owners.