9
Tel: (206) 283-2000
Fax: (206) 283-7546
IN-PLACE
WATERSTOPS,
REGLETS,
FLASHINGS,
PROTECTION FILMS
& COVERS
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
Construction Specialties Co., Inc.
9
9-
COLLOID ENVIRONMENTAL TECHNOLOGIES COMPANY
WATERSTOP-RX
Concrete Joint Waterstop
• Active, swelling waterstop
• Fast and easy Installation
• Seals around penetrations
• Ideal when pouring against existing concrete
WATERSTOP-RX® is a flexible strip concrete construction joint
waterstop that provides a positive seal by expanding upon contact
with water. WATERSTOP-RX is an active bentonite/butyl rubberbased waterstop that is designed to replace conventional passive
PVC dumbbell waterstops, thus eliminating the requirement of
split-forming and product seam welding. The key to WATERSTOPRX’s effective­ness is its 75% sodium bentonite content which
provides superior expansion to seal and fill small voids. Recognized
worldwide, WATERSTOP‑RX has a proven track record as a high
quality and cost-effective solution to water
infiltration problems.
The Original
expanding waterstop
Applications include both vertical and horizontal concrete construction joints, new to existing construction, irregular surfaces,
and around through-wall penetrations, such as plumbing and
electrical conduit. WATERSTOP-RX is designed for both hydrostatic
and non-hydrostatic conditions. However, WATERSTOP-RX is not
designed, nor intended to function as an expansion joint sealant.
Contact manufacturer for precast concrete applications, technical
information and approval.
WATERSTOP-RX is manufactured in lightweight, flexible coils
that can be installed in both hot and cold weather. The product
is adhered to concrete, steel, and PVC (Pipes) with Volclay WBADHESIVE at or exceeding the required minimum distance from
the exterior concrete surface. Coil ends are butted together—not
overlapped—to form a continuous waterstop. In most applications
WATERSTOP-RX is installed to the interior side of the outer row
of steel reinforcement to allow for sufficient concrete coverage.
WATERSTOP-RX should only be used in applications where the
Tel: (206) 283-2000
Fax: (206) 283-7546
product is completely encapsulated within the concrete.
WATERSTOP-RX is designed for structural concrete with a
minimum of 3000 psi. WATERSTOP-RX 101 and WATERSTOP‑RX
101T, including the
RH formula of each,
require a minimum of
3” of concrete coverage. WATERSTOPRX 102RH requires
a minimum concrete
coverage of 2” RX
101 and RX 101T
products are designed for vertical and
hori­zontal reinforced
concrete 8” thick or
greater with two rows
of reinforcing steel.
RX 102 products shall
be used in concrete
with one row of reinforcement, concrete
curbs, planter walls
and lightweight concrete.
WATERSTOP-RX is not a self-adhering product. Volclay WB‑ADHESIVE is required to secure WATERSTOP-RX to concrete, metal
or PVC (Pipe) surfaces.
• Eliminates Split-Forming, Splices and Welding—
saving time and labor costs
• Active material seals small cracks and voids permanently
• flexible lightweight product that contours irregular concrete and penetrations
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
Construction Specialties Co., Inc.
9
9-
Construction Specialties Co., Inc.
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
9
ACCESSORY PRODUCTS
WB-ADHESIVE is a water-based, latex adhesive specially formulated to adhere WATERSTOP-RX. Upon application, WB-ADHESIVE
changes color from gray to black while curing. Install WATERSTOPRX to cured, black adhesive within six hours of turning black.
WB-ADHESIVE is a non-flammable product with a flash point
200°F. Do not allow WB-ADHESIVE to freeze. Store in a warm,
dry location prior to use.
9-
Tel: (206) 283-2000
Fax: (206) 283-7546
Construction Specialties Co., Inc.
Concrete structures are only as watertight as the waterstops that join them. Greenstreak waterstops stop leaks
before they start…in the joints of concrete structures.
Since 1950, Greenstreak has served the general and architectural
concrete construction industry. Innovation, engineering and quality
craftsmanship are combined to produce products of choice for the
industry’s owners, designers and contractors.
Greenstreak maintains its position of industry leadership by
responding to the unique needs of our customers. Greenstreak’s
dedicated technical and customer service staff are active participants in the concrete industry to take advantage of the latest
technological advances, communicate with our market and
analyze trends.
Typical Structures Requiring Waterstops Include:
• Dams, Locks, Canals, Water Reservoir and Aqueducts
• Water and Waste Water Treatment Facilities
• Primary and Secondary Containment Structures
• Culverts and Tunnels
• Storage Tanks
• Retaining Walls
• Bridge and Deck Abutments
• Foundations
• Slabs-on-Grade
• Parking Garages
Hydrotite®
Hydrotite is a world renowned hydrophilic waterstop. Composed of
modified chloroprene rubber, Hydrotite expands up to 8 times its
original volume when exposed to water. This expan­sion creates an
effec­tive com­pres­sion seal with­in joints of limited move­ment.
Hydrotite is used extensively in seal­ing
concrete construction
and control joints,pipe
penetrations, precast
concrete segments,
tunnel lining setments
and for repair of existing joints.
Hydrotite features include:
• Volumetric Expansion Up to 8:1
• Durable Chloroprene Rubber Compostion
• Delay Coating to Protect Fresh Concrete
• Composite Profiles; Controls Direction of Expansion
• Eliminates Special Form Work
• Installs Quickly
• Easy to Splice
Swellstop™ Waterstop
A flexible butyl rubber and swellable clay waterproofing compound that swells upon contact with water to form a long lasting
compression seal in non-moving concrete joints.
Swellstop requires a 2” minimum clear coverage from the face
of the concrete.
Applications include:
• Foundation Walls and Slabs
• Slabs-on-Grade
• Precast Wall Panels
• Manholes
• Pipe Connections
• Box Culverts
• Utility and Burial
Vaults
• Wet Wells
• Portable Water
Tanks
Lockstop™ Waterstop
Similar in appearance to Swellstop™ but different in nature. Lockstop is a single-component self-sealing mastic waterstop which
prevents moisture from penetrating non-moving concrete joints.
Typical Construction joint applications include:
• Foundation Walls and Slabs
• Slabs-on-Grade
• Manholes
• Pipe Connections
• Retaining Walls
• Tunnels
• Culvert
• Storage Tanks
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
Waterstops for Concrete
Tel: (206) 283-2000
Fax: (206) 283-7546
9
Note: Swellstop and Lockstop are for non-working joints only.
9-
Construction Specialties Co., Inc.
Tel: (206) 283-2000
Fax: (206) 283-7546
Types of Concrete Joints
WATERSTOPS FOR NON-WORKING JOINTS
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
9
9-
WATERSTOPS FOR WORKING JOINTS
RETROFIT APPLICATIONS
Construction Specialties Co., Inc.
Tel: (206) 283-2000
Fax: (206) 283-7546
Waterstop Profiles
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
PVC SHAPES
9
9-
Construction Specialties Co., Inc.
PVC SHAPES
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
9
9-
Tel: (206) 283-2000
Fax: (206) 283-7546
Tel: (206) 283-2000
Fax: (206) 283-7546
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
Construction Specialties Co., Inc.
9
9-
Construction Specialties Co., Inc.
Tel: (206) 283-2000
Fax: (206) 283-7546
Superior Water Penetration Resistance
Precision manufactured Springlok Flashing Systems offer the
ultimate in protection from the elements.
• Flashing snaps-in under the reglet so water can’t get under the
flashing.
• Reglet has a 1” end lap and flashing has a 3” end lap to eliminate
leaky butt joints and ensure a perfectly watertight seal.
• Flashing has a positive air-break to prevent water from climbing
under the flashings.
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
9
Easier Installation
Lightweight material in ten foot lengths makes handling on the job
site easy. Precision, factory produced parts insure perfect fit on the
job. Flashing snaps quickly into reglets with no need for fasteners
to hold it in place.
Removable/Reusable Flashing
Springlok Flashing snaps into reglets and is held in place without
screws or clips. When reroofing must be done, the flashing is simply
snapped out without damage and can be reused.
Factory Fabricated Corners
Fry Reglet offers factory fabricated reglet and flashing corners to
eliminate time consuming job site fabrication.
Springlok® Flashing System
For nearly 50 years, Fry Reglet has produced a compre­
hensive selection of reglet and flashing systems for the
roofing industry. These functional moisture prevention
products have provided superior protection for a variety
of roofing applications.
Specifier Preference
Nearly 50 years of success with Springlok Flashing Systems have
created specifier preference.
Because Fry Reglet appears in most specifications, Springlok
Flashing Systems can be used without time-consuming change
orders.
Resistance to Roof Blow-off
Tests by the Center for Applied Engineering, an accredited independent laboratory, prove the ability of Springlok Flashing Systems
to resist blow-off in high winds.
Springlok Flashing
Springlok Flashing Systems were subjected to 110 mph wind
velocities (plus/minus 5%) for two hours. Even without wind
clips, the laboratory reported “No life or movement of the reglet
or flashing.”
Blow-offs happen when winds penetrate the flashing and get
under the roof and blow it off exposing interiors from wind or rain.
Springlok Flashing Systems minimize this danger.
Engineered for Specific Applications
Fry Reglet offers six flashing systems, each tailored to a specific
situation. So, roofers can choose the exact reglet for their project
and be assured of complete satisfaction.
9-10
Fry Reglet Springlok Flashing is the heart of the System. Its special
shape permits it to snap into all reglet shapes except Original Reglet
with no need for clips or screws. The unique bottom shape provides
a positive air break to prevent water from climbing between the
roof and flashing.
Construction Specialties Co., Inc.
Springlok Reglets
Six types of Springlok Reglets are offered. Each reglet shape is
specifically designed for a particular type of substrate.
Type SM Surface Mounted
Tel: (206) 283-2000
Fax: (206) 283-7546
Type STX Stucco Reglet
A superior reglet design developed specifically for stucco conditions. The “V” projection permits stucco to be applied directly
over the reglet.
Type CO Concrete Reglet
Type MA and MA-4 Masonry
This reglet, designed for masonry application is laid into
masonry joints and held in place as mortar cures. There is
no opening for water penetration. Type MA reglet has a
1-1/2” top flange and Type MA-4 has a 4” top flange.
Type ST Stucco Reglet
This reglet is made especially for stucco applications. It is put in
place over 3/4” base board and stucco is applied over the top of
the reglet.
This reglet is designed to be installed into poured-in-place concrete construction. Face of reglet is covered with Foam Backer
Rod to prevent grout from getting into the reglet. Connector clips
are supplied to provide positive alignment at joints and prevent
leakage of concrete during pouring. Special staples are supplied
to aid installation of reglet.
NOTE: For tilt-up concrete use Type SM Reglet.
Materials and Finishes
All reglets and Springlok Flashings are available in the following
materials with finish/color as shown.
Material/Thickness
Finish/Color
• Galvanized Steel Standard zinc finish
(26 ga–flashing and CO;
others–24 ga)
• Copper (16oz)
Standard uncoated finish
• Aluminum (.025”)Gray Paint
• Stainless Steel (.020”) Standard uncoated finish
Type 304
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
Type SM reglets are designed for surface mounting with drive
pins. Sealant applied at two places (at top and in recess)
seals against water penetration. Special “atmoseal” washers
(7/8” diameter stainless steel with neoprene facing) are
shipped with reglets to seal drive pin penetrations.
9
9-11
Construction Specialties Co., Inc.
Prefabricated Mitered Corners
Fry Reglet will provide factory mitered and welded corners for any
reglet and for Springlok Flashing. This eliminates the need for time
consuming, expensive, job site corner fabrication.
Tel: (206) 283-2000
Fax: (206) 283-7546
Termination Bars
The Fry Reglet line of Termination Bars offers five ways to terminate
single-ply roofing to provide a choice of costs and effectiveness.
All Termination Bar are extruded aluminum (6063 Alloy) with a mill
finish and corners radiused so there are no sharp edges. Slotted
holes for nailing can be provided on 6”, 8” and 10” centers. All
termination bars are packaged 50, 10 foot long pieces per tube.
Versabar
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
9
Unique design of this .100”
thick bar offers special benefits:
• Usable as a channel
bar or by changing the
orientation, for use with
sealant.
• Bottom ridges pull tightly
down against membrane
for perfect seal.
Type OR Original Reglet
A watertight, permanent reglet designed with a beveled flange to
lock reglet firmly into concrete. This reglet is designed for use in
flashing the tops of parapets or as part of a gravel stop.
Lip Bar
.09” thick lip bar with 45° angled top for
application of sealant between termination
bar and wall.
Channel Bar
.106” thick channel bar with 1/4” legs top
and bottom for effective sealing.
Heavy Flat Bar
Top of Parapet Flashing Gravel Stop
Easily installed; built-in key for locking Provides cleaner, more attractive appearance.
into concrete. Permanently waterproof
with vinyl rope as backup for sealant.
.125” thick flat bar with slotted holes for
installation, pulls tight to membrane for a
good seal.
Flat Bar
.093” thick economical flat bar with slotted holes for easy installation over end of
single-ply roofing at terminations.
9-12
Construction Specialties Co., Inc.
MOISTOP ULTRA 10 & ULTRA 15
Description
Moistop Ultra 10 and Ultra 15 represents a new standard for
concrete underslab products. With a water vapor permeance of
.02 perms and a tensile strength and puncture resistance that
outperforms even thicker membranes, Moistop Ultra 10 and Ultra
15 exceeds ASTM E-1745-97 Class A, B, and C requirements for
underslab vapor retarders. Manufactured from ISO certified virgin
resins through a unique process, Moistop Ultra 10 and Ultra 15
are extremely durable and puncture resistant.
Limitations
Product not covered within a reasonable amount of time after
application should be submitted for testing. Product should be
covered as soon as possible. Inspect product to ensure it is free
of any punctures or damage which may detract from the underslab
vapor retarder integrity. Product should be as clean and dry as
possible before sealing with Moistop Tape. Not recommended for
below grade vertical waterproofing applications.
Size and Weight
Moistop Ultra 10 - Moistop 10 is supplied in 3,000 sq. ft. rolls
(180” by 200’; weight is approximately 4.8 lbs/100 sq. ft. Thickness is 10 mils.
Moistop Ultra 15 - Moistop 15 is supplied in 1,440 sq. ft. rolls
(144” by 120’; weight is approximately 7.3 lbs./100 sq. ft. Thickness is 15 mils.
Installation
Supplied in seamless 15 foot (Ultra 10), 12 foot (Ultra 15) wide
rolls, both roll out quickly and smoothly over leveled and tamped
soil or compacted fill. After the base for the concrete has been
leveled, compacted, and tamped, install the vapor retarder over the
base and compacted fill, with the longest dimension parallel to the
direction of the pour of the concrete. All joints should be lapped
6” (152 mm) and sealed with Moistop Tape. Seal penetrations with
the Boot and Moistop Tape.
‘Weather-All’ Brand
Polyethylene Film Products
TRM “Weather-All’ brand multi-purpose polyethylene films have
been found to meet or exceed the minimum physical property
requirement set forth in the following specifications:
1National Bureau of Standards Voluntary Product Standard PS 1769
2 Federal Specification LP 378d, Type 1, Class 1, Grade A, Finish 1
3 American Society for Testing and Materials, ASTM D2103, Type
00001
4 Federal Specification LS-137, requiring no evidence of fungus
growth
5 ASTM E-96, Procedure E, requiring that water vapor permeance
shall be no greater than 1.40 grams per 100 square inches in are
per 24 hours for film 1mil in thickness; in other thicknesses inversely
proportional to the thickness
6 ASTM tentative G-156, Moisture Retention, requiring that loss of
water will not exceed 0.055 G/CM2
7 ASTM D-882-67, Method A, requiring the following mechanical
properties:
Tensile Strength, min psi 1700 lengthwise, 1200 crosswise
Elongation, min percent 225 lengthwise, 350 crosswise
8Minimum requirements set forth in Federal Specification UUP-147B
and FHA Bulletin UM20A
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
Fortifiber Building
System Group
Tel: (206) 283-2000
Fax: (206) 283-7546
9
Color: Clear, Black, White - Fire Retard
Thickness: 2, 4, 6, 8 & 10 mil
9-13
Construction Specialties Co., Inc.
Stego® Wrap 10-mil Class
A Vapor Retarder
Product Description
USES: Stego Wrap 10-mil is used as an exceptional vapor retarder, and as a protection
course for below grade waterproofing applications.
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
9
COMPOSITION: Stego Wrap 10-mil is a multi-layer plastic extrusion manufactured with only the highest grade of prime, virgin,
polyolefin resins. Stego Wrap 10-mil exceeds ASTM E 1745
Class A, B & C.
SIZE: Stego Wrap 10-mil comes in rolls 14’ x 210’ or 2,940 ft2
WEIGHT: Stego Wrap 10-mil rolls weigh approximately 141 lbs.
Installation
UNDERSLAB: Unroll Stego Wrap 10-mil over an aggregate, sand
or tamped earth base. Overlap all seams a minimum of 6” and
tape using Stego Tape. All penetrations must be sealed using a
combination of Stego Wrap, Stego Tape and/or Stego Mastic.
VERTICAL WALL: Install Stego Wrap 10-mil over the waterproofing
membrane while still tacky. Mechanically fasten Stego Wrap to the
wall at the top with termination bar and concrete nails. Drape Stego
Wrap down across the footer and under the french drain.
Stego® Wrap 15-mil Class A Vapro
Retarder
Product Description
USES: Stego Wrap 15-mil is used as a true below-slab vapor
barrier, and as a protection course for below grade waterproofing
applications.
COMPOSITION: Stego Wrap 15-mil Vapor B arrier is a multi-layer
plastic extrusion manufactured with only the highest grade of prime,
virgin, polyolefin resins.
SIZE: Stego Wrap 15-mil rolls weigh approximately 141 lbs.
Installation
UNDERSLAB: Unroll Stego Wrap 15-mil Vapor Barrier over an
aggregate, sand or tamped earth base. Overlap all seams a
minimum of 6” and tape using Stego Tape. All penetrations must
be sealed using a combination of Stego Wrap, Stego Tape and/or
Stego Mastic.
VERTICAL WALL: In stall Stego Wrap 15-mil Vapor Barrier over
the waterproofing membrane while still tacky. Mechanically fasten
Stego Wrap to the wall at the top with termination bar and concrete
nails. Drape Stego Wrap down across the footer and under the
french drain.
9-14
Tel: (206) 283-2000
Fax: (206) 283-7546
Stego® Mastic
Product Description
USES: Stego Mastic is designed to
be used as a waterproofing and vapor retardant membrane for use in
conjunction with Stego Wrap 10-mil
and 15-mil Vapor Retarder/Barrier.
Stego Mastic can be used as an
alternate to boots for pipe penetrations in Stego Wrap Vapor Barrier.
Stego Mastic can also be used as a
primary waterproofing for below grade walls.
COMPOSITION: Stego Mastic is a medium-viscosity, water-based,
polymer-modified anionic bituminous/ asphalt emulsion, which
exhibits bonding, elongation and waterproofing characteristics.
SIZE: Stego Mastic comes in 5 gallon buckets.
Installation
PREPARATION
• A test application simulating the project environment should
always be done prior to final usage of Stego Mastic.
• All Surfaces should be dry and free of loose materials, oils
and other contaminants. The surfaces should be cleaned in
the same fashion as the test surface in order to ensure proper
results.
• Store above 40°F
PENETRATIONS
For small pipe and rebar penetrations in Stego Wrap Vapor Barrier cut Stego Wrap just big enough for the penetration. Liberally
apply Stego Mastic around the penetration to keep the integrity
of the membrane intact. Stego Mastic can be applied by brush,
roller, or sprayer.
NOTE:
1: For larger penetrations or wide cut-outs of Stego Wrap, use Stego
Wrap and Stego Red Polyethylene Tape to construct boots.
2: Solvent-based products should not be applied over this
product.
Tel: (206) 283-2000
Fax: (206) 283-7546
Stego® Tape
Stego® Cold Weather Tape
Product Description
USES: Stego Tape is a low permeance tape
designed for protective sealing, hanging,
seaming, splicing, and patching applications where a highly conformable material is required. It has been engineered
to bond specifically to Stego Wrap Vapor
Retarder/Barrier, making it ideal for sealing Stego Wrap seams
and penetrations.
Product Description
USES: Stego Cold Weather
Tape is a low permeance
tape designed for protective
sealing, hanging, seaming,
splicing, and patching applications where a highly
conformable material is
required. It has been engineered to bond specifically
to Stego Wrap 10-mil and
15-mil at cold temperatures
making it ideal for sealing Stego Wrap seams and penetrations in
cold weather.
COMPOSITION: Stego Tape is composed of a high-density polyethylene film and a rubber-based, pressure-sensitive adhesive.
SIZE: Stego Tape comes in 4“ wide, 180 ft. long rolls. Stego Tape
ships 12 rolls in a case.
Installation
SEAMS: Overlap Stego Wrap 6 inches and seal with Stego Tape.
Make sure the area of adhesion is free from dust, dirt and moisture
to allow maximum adhesion of the pressure sensitive tape.
PIPE BOOTS:
1) Cut a piece of Stego Wrap. Width: minimum 12”
Length: 1 1/2 times the pipe circumference
2) With scissors, cut slits half the width of the film.
3) Wrap boot around pipe and tape onto pipe, completely taping
the base to Stego Wrap using Stego Tape. Stego Tape should be
installed above 40ºF.
COMPOSITION: Stego Cold Weather Tape is composed of a highdensity polyethylene film and a rubberbased, pressure-sensitive
adhesive.
SIZE: Stego Cold Weather Tape comes in 4” wide, 180 ft. long rolls.
Tape ships 12 rolls in a case.
Installation
SEAMS: Overlap Stego Wrap 6 inches and seal with Stego Cold
Weather Tape. Make sure the area of adhesion is free from dust,
dirt and moisture to allow maximum adhesion of the pressure
sensitive tape.
PIPE BOOTS:
1) Cut a piece of Stego Wrap. Width: minimum 12” Length: 1 1/2
times the pipe circumference
2) With scissors, cut slits half the width of the film.
3) Wrap boot around pipe and tape onto pipe, completely taping
the base to Stego Wrap using Stego Cold Weather Tape. Stego Cold
Weather Tape can be installed in extremely low temperatures.
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
Construction Specialties Co., Inc.
9
9-15
Construction Specialties Co., Inc.
Tel: (206) 283-2000
Fax: (206) 283-7546
Max Katz Bag Co., Inc.
Construction Products Division
Hi-Temperature, Pressure Sensitive,
Adhesive Back Covers for Waterstop
Splicing Irons
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
easy to use • no tools needed
• Fast—saves time and money.
• More Efficient—direct heat transfer.
• Take the Screws out of Cover Changes.
Poly Film
a superior heavy-duty film that resistS tears in
any direction!
Whenever you need an extra strong fabric to protect your work
sites, materials or equipment from moisture, rain, snow or
wind—Ma Ka® Reinforced Poly Film is the ideal all purpose
economical cover material.
• Building Enclosures
• Material covers
• Export Racking
Covers
• Shipping
Covers
• Equipment
Covers
• Aggregate
Covers
All-Weather Building Enclosures.
• Pallet
Covers
• Temporary Liners, etc.
Clear Stock Size Rolls
20’and 40’
20” Fire Rated
9
Peel and Stick
Part #
Iron SizeNo per Carton
PS 214
PS 414
PS 620
AP 389
2” x 14”
4-1/2” x 14”
6” x 20”
Adapter Plate
for PS 214
12 ea
12 ea
12 ea
1 per/pkg
standard cover (screw-on)
SC 154
SC 214
SC 414
9-16
1-1/2” x 4”
2” x 14”
4-1/2” x 14”
12 ea
12 ea
12 ea
All-Weather Building Enclosures.
Construction Specialties Co., Inc.
Tel: (206) 283-2000
Fax: (206) 283-7546
BILTRITE® Butyl Sheet
Applications
Many applications from gaskets and washers to press pads. Very popular with
manufacturers of tire inner liners and inner tubes.
Butyl is a non-oil resistant compound which has good resistance to gas permeation, acids,
alkalies, and ozone at moderately high temperatures. Resists weathering, sunlight water absorption,
corona, animal and vegetable oils. Resistance to flexing and abrasion is outstanding.
Physical Properties
WATERPROOF FLASHING MEMBRANE
Description:
Composed of premium grade SBS modified bitumen laminated between a super strong, yet very flexible,
UV resistant woven polyethylene complex on face side, and a silicon release plastic film on the back
side. This creates the most versatile self sealing waterproof flashing membrane available, allowing both
stick on or nail on installations.
Available Sizes:
4”, 6”, 9”, 12”, 18” and 36” roll widths by 75’ in length.
Available Thicknesses:
25 and 40 mil
Core Types:
SUMMER - Best adhesion temp 50°F or above, service temp up to 194°F
WINTER - Best adhesion temp 14°F or above, service temp up to 194°F
HIGH TEMP - Best adhesion temp 50°F or above, service temp up to 221°F
In-Place Waterstops, Reglets, Flashings,
Protection Films & Covers
Style #60
9
NAIL ON FLASHING
Description:
Constructed from heavy weight woven Polypropylene mat, laminated between two layers of UV resistant
polypropylene, blended with other specialty resins to create the strongest, most durable, inorganic, fungi
resistant, UV resistant, flexible nail on window and door flashing available
Available Sizes:
9”, 12” and 18” roll widths by 300’ in length
CORNER GUARDS
Description:
Designed to flash and protect one of the most critical areas of your window rough opening; the sill, jam and sheathing face.
Our patent pending design allows for fast, easy nail on or screw on installation and works with both 2x4 and 2x6 wood or metal studs.
9-17