®
Multi-Application Peripherals and Accessories
ULC Listed*
Non-Coded Manual Stations
2099 Series Single and Double Action Operation
Features
• Single action models
FIRE
ALARM
• Breakglass type double action models
• Institutional option:
– Key operated only
PULL DOWN
• Pull lever protrudes when alarmed
• Tamper resistant reset key lock:
– keyed same as fire alarm cabinet
• Pre-signal and annunciator contact options
Single Action Station
• Surface or semi-flush mounting
• Flush mounting option
• Two stage alarm
• English, French, or Bilingual
Operation
Single Action Stations require a firm downward pull to
activate the alarm switch. Completing the action breaks an
internal plastic break-rod (visible below the pull lever).
The pull lever latches into the alarm position and remains
extended out of the cover to provide a visible indication of
which station was alarmed.
Double Action Stations (Breakglass) require the operator
to strike the front mounted hammer to break the glass and
expose the recessed pull lever. The pull lever then operates
as a single action station.
Single action stations can be fitted with an institutional
cover kit. Institutional Stations are designed to activate
by key operation only. This allows access for manual
alarms to be limited to authorized personnel. Operation
requires key insertion and opening of the station cover.
Pre-signal option activates when the lever is pulled.
General alarm initiation requires a key to activate a
keyswitch located behind the pull lever.
Station Reset requires use of a key to reset the pull station
lever and deactivate the alarm switch. If the break-rod is
used, it must be replaced.
FIRE
ALARM
BREAK
PULL
GLASS
DOWN
Double Action
Station (Breakglass)
FIRE
ALARM
KEY
OPERATED
ONLY
Single Action Station
with Institutional Cover
Testing requires physical activation of the pull lever
(except for institutional stations).
© 2000 Simplex International Time Equipment Co. Ltd.
S12099-0007-1 9/00
Applications
According to the National Building Code, a manual pull
station shall be installed in every floor area near every
required exit. CAN/ULC-S524-M91 states that stations “shall
be mounted not less than 1200 mm nor more than 1400 mm
above the floor level...”. In addition, the National Fire
Protection Assocation (NFPA), Bulletin number 72 (reference
section 5-9), gives specific minimum requirements on this
subject. When manual station coverage appears limited in any
way, additional units should be installed. Stations should be
mounted with the bottom of the station not less than 1.07 m
(3.5 ft.) or more than 1.52 m (5 ft.) from the floor. Usually
stations are mounted at the 1.37 m (4.5 ft.) level. (In order to
make buildings and facilities accessible to, and usable by the
physically handicapped, some specifications may require that
the station be installed not more than 1.07 m (3.5 ft.) from the
floor.)
Stations should be located in the normal path of exit, and
distributed in the protected area so that they are unobstructed
and readily accessible.
Stations should be provided on each floor to obtain a travel
distance not more than 61 m (200 ft.) to the nearest station
from any point in the building. One station should be
provided for each floor where the maximum floor area is
2
2
930 m (10,000 ft. ) or more.
Construction. Covers and pull levers are constructed of chip
resistant and dirt resistant, high impact Lexan polycarbonate.
Covers are red with white lettering and pull levers are white
with red lettering.
The 2099-9819 (Black) and 2099-9820 (Beige) are
optional adapter kits designed to flush mount any one of
the 2099 series stations.
Non-addressable Manual Station Specification Chart
Single Action Models
Actuator
2099-9754C
N/O
Actuator Annun.
GA Key
Single Gang Box Depth
mm (inches)
38 (1.5)
2099-9288C
N/O
N/O
51 (2.0)
2099-9752C
N/O:C/L
N/O
51 (2.0)
2099-9101C
N/O
N/O
2099-9107C
N/O
N/O
N/O
76 (3.0)
2099-9110C
N/O:C/L
N/O
N/O
51 (2.0)
2099-9102C
N/O
N/C
2099-9109C
N/O
N/C
N/O
76 (3.0)
2099-9111C
N/O:C/L
N/C
N/O
51 (2.0)
Double Action Models
- Breakglass
Actuator
Actuator Annun.
GA Key
Single Gang Box Depth
mm (inches)
2099-9103C
N/O
2099-9336C
N/O
N/O
51 (2.0)
2099-9772C
N/O:C/L
N/O
51 (2.0)
2099-9104C
N/O
N/O
2099-9108C
N/O
N/O
N/O
2099-9118C
N/O:C/L
N/O
N/O
2099-9105C
N/O
N/C
2099-9117C
N/O
N/C
N/O
76 (3.0)
2099-9119C
N/O:C/L
N/C
N/O
51 (2.0)
51 (2.0)
51 (2.0)
38 (1.5)
51 (2.0)
76 (3.0)
51 (2.0)
51 (2.0)
N/O = Normally Open Contact — N/C = Normally Closed Contact — C/L = Current Limited when activated
MODELS SHOWN ARE ENGLISH LANGUAGE. ADD ‘F’ FOR FRENCH – ‘B’ FOR BILINGUAL
e.g. 2099-9754C, 2099-9754CF, 2099-9754CB
Accessories
Model
Description
2099-9803
Replacement breakglass (standard, English)
2099-9804
Replacement break-rod
2099-9819
Flush adapter kit, black (refer to page 4)
2099-9820
Flush adapter kit, beige (refer to page 4)
2099-9822
Replacement retaining clip for breakglass
2099-9828
Institutional cover kit
2975-9178
Red, surface mount box, sheet metal, 5 3/16” H x 4” W x 2 3/16” D (127 mm x 102 mm x 56 mm)
2975-9022
Red, cast aluminum surface mount box, 5” H x 3 7/8” W x 2 3/16” D (127 mm x 98 mm x 56 mm)
12975-0001
Red, surface mount box, sheet metal, 5 3/16” H x 4” W x 2 11/16” D (127 mm x 102 mm x 68 mm)
S12099-0007-1 9/00 Page 2
Mounting Information
Refer to installation instructions (PER-21-502CAN) for additional information.
SURFACE MOUNTING
4” (102 mm)
Knockouts for 3/4 inch conduit
located top and bottom
12975-0001 or
2975-9178 Box
FIRE
ALARM
5” 3/16
(132 mm)
Station cover
hinges open for
installation access
PULL DOWN
5”
(127 mm)
12975-0001 – 2 11/16” (68 mm)
2975-9178 – 2 3/16” (56 mm)
12975-0001 or
2975-9178 Box
1” (25.4 mm)
3 3/4” (95 mm)
Side View,
Surface Mounting
SEMI-FLUSH MOUNTING, 4” BOX
(refer to selection chart for requirements)
4” (102 mm) square box, 2 1/8” (54 mm) minimum
depth RACO #231 or equal (supplied separately)
FIRE
Electrical box
Station side view
ALARM
PULL DOWN
Single gang cover plate
Single gang cover plate, 3/4” (19 mm)
extension, RACO #773 or equal
(supplied separately)
Wall
Surface
Side View, Semi-Flush Mounting
S12099-0007-1 9/00 Page 3
Mounting Information (continued)
FLUSH MOUNTING REFERENCE INFORMATION
Front View
Flush mount adapter kit
2099-9819, Black
2099-9820, Beige
Side View
Box must be recessed into wall
1” to 1 1/8” (25.4 mm to 29 mm)
FIRE
ALARM
8”
(203 mm)
6”
(152 mm)
PULL DOWN
4 3/4” (121 mm)
Hole cutout must be a
minimum of 6” H x 5” W
(152 mm by 127 mm)
Wall
Surface
4 11/16” (119 mm)
square box, 2 1/8”
(54 mm) minimum
depth (by others)
6 3/4” (171 mm)
Simplex, the Simplex logo, MAPNET, and IDNet are either trademarks or registered trademarks of Simplex Time Recorder Co. in the U.S. and/or other countries. NFPA 72 and
National Fire Alarm Code are registered trademarks of the National fire Protection Association (NFPA). Lexan is a registered trademark of General Electric Co.
®
S12099-0007-1 9/00
2400 Skymark Avenue, Mississauga, Ontario L4W 5K5
Offices and Representatives Throughout the World.
Visit us on the world wide web at www.simplexnet.com
All specifications and other information shown were current as of printing and are subject to change without notice. Printed in Canada.