Analog Devices Welcomes
Hittite Microwave Corporation
NO CONTENT ON THE ATTACHED DOCUMENT HAS CHANGED
www.analog.com
www.hittite.com
THIS PAGE INTENTIONALLY LEFT BLANK
HMC1160LP5E
v00.0814
VCOS WITH FO/2 OUTPUT - SMT
MMIC VCO WITH HALF FREQUENCY OUTPUT
8.45 - 9.30 GHz
Typical Applications
Features
Low noise MMIC VCO w/Half Frequency Output for:
Dual output: F
o = 8.45 GHz - 9.3 GHz
Fo/2 = 4.225 GHz - 4.65 GHz
Pout: +12 dBm
• Point to point/multipoint radio
• Test equipment and industrial controls
• VSAT
Phase noise: -116 dBc/Hz @100 kHz
No external resonator needed
RoHS compliant 5 x 5 mm SMT package: 25 mm²
General Description
Functional Diagram
The HMC1160P5E is a MMIC voltage controlled
oscillator that integrates resonator, negative resistance device, varactor diode and features a half
frequency output. Output power and phase noise
performance are excellent over temperature due to
the oscillators’ monolithic construction. Power output
is +12 dBm typical from a +5V supply voltage. The voltage controlled oscillator is housed in a RoHS compliant SMT package and requires no external matching
components.
Electrical Specifications, TA = -40°C to +85°C, Vcc = +5V
Parameter
Frequency range
Power output
SSB phase noise
Tune voltage
Min.
Fo
Fo/2
RFOUT
RFOUT/2
9
0
10 kHz offset
100 kHz offset
Vtune
Supply current (Icc) (Vcc = +5V)
Typ.
-90
-116
Output return loss
Harmonics/subharmonics
Pulling (into a 2.0:1 VSWR)
1
1/2
2nd
3rd
Units
GHz
GHz
17
8
dBm
dBm
-85
-110
dBc/Hz
dBc/Hz
2
13
V
195
325
mA
10
µA
40
250
MHz/V
Tune port leakage current (Vtune = 13V)
Tuning sensitivity
Max.
8.45 - 9.3
4.225 - 4.65
2
dB
37
18
30
dBc
dBc
dBc
4.5
MHz pp
Pushing @ Vtune = 5V
5.5
MHz/V
Frequency drift rate
0.74
MHz/°C
For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, Norwood, MA 02062
978-250-3343 tel • 978-250-3373 fax • Order online at www.analog.com/hittitemw
Application Support: Phone: 978-250-3343 or RFMG-apps@analog.com
HMC1160LP5E
v00.0814
MMIC VCO WITH HALF FREQUENCY OUTPUT
8.45 - 9.30 GHz
Frequency vs. Tuning Voltage
Frequency vs. Tuning Voltage, T = 25°C
9.5
9
8.5
8
7.5
7
9.5
9
8.5
8
7.5
7
0
1
2
3
4
5
6
7
8
9
10 11 12 13
0
1
2
3
4
TUNING VOLTAGE (Vdc)
+25C
+85C
-40C
Sensitivity vs. Tuning Voltage
7
8
9
10 11 12 13
5.00V
5.25V
Output Power vs. Tuning Voltage
16
14
500
OUTPUT POWER (dBm)
SENSITIVITY (MHz/Volt)
6
4.75V
600
400
300
200
100
12
10
8
6
4
2
0
0
0
1
2
3
4
5
6
7
8
9
0
10 11 12 13
+25C
+85C
1
2
3
4
5
6
7
8
9
10 11 12 13
TUNING VOLTAGE (Vdc)
TUNING VOLTAGE (Vdc)
+ 25C
-40C
SSB Phase Noise vs. Tuning Voltage
-50
-80
-60
-85
-90
-95
-100
-105
-110
-115
-120
+ 85C
- 40C
SSB Phase Noise @ Vtune = +5V
-75
SSB PHASE NOISE (dBc/Hz)
SSB PHASE NOISE (dBc/Hz)
5
TUNING VOLTAGE (Vdc)
VCOS WITH FO/2 OUTPUT - SMT
10
OUTPUT FREQUENCY (GHz)
OUTPUT FREQUENCY (GHz)
10
-70
-80
-90
-100
-110
-120
-130
-140
-125
0
1
2
3
4
5
6
7
8
9
10 11 12 13
TUNING VOLTAGE (Vdc)
+25C 10 kHz
+ 25C 100 kHz
+85C 10 kHz
+85C 100 kHz
-40C 10 kHz
-40C 100 kHz
-150
3
10
4
5
10
10
OFFSET FREQUENCY (Hz)
+25C
+85C
6
10
-40C
For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, Norwood, MA 02062
978-250-3343 tel • 978-250-3373 fax • Order online at www.analog.com/hittitemw
Application Support: Phone: 978-250-3343 or RFMG-apps@analog.com
2
HMC1160LP5E
v00.0814
MMIC VCO WITH HALF FREQUENCY OUTPUT
8.45 - 9.30 GHz
RFOUT/2 Frequency vs. Tuning Voltage
RFOUT/2 Output Power
vs. Tuning Voltage
7
4.75
OUTPUT POWER (dBm)
OUTPUT FREQUENCY (GHz)
8
4.5
4.25
4
3.75
6
5
4
3
2
1
0
3.5
0
1
2
3
4
5
6
7
8
9
10 11 12 13
0
1
2
3
TUNING VOLTAGE (Vdc)
+25C
4
5
6
7
8
9
10 11 12 13
TUNING VOLTAGE (Vdc)
+85C
-40C
+ 25C
Supply Current vs. Tuning Voltage
300
+ 85C
- 40C
Typical Supply Current vs. Vcc
Vcc (V)
290
Icc (mA)
4.75
240
270
5.00
260
260
5.25
275
280
Icc (mA)
VCOS WITH FO/2 OUTPUT - SMT
5
250
240
230
220
210
200
0
1
2
3
4
5
6
7
8
9
10
11
12
13
TUNING VOLTAGE (V)
+25C
+85C
-40C
Absolute Maximum Ratings
3
Vcc
+5.5 Vdc
Vtune
0V to +15V
Storage temperature
-65 °C to +150 °C
ESD sensitivity (HBM)
Class 1A
Reliability Information
Junction temperature to maintain
1 million hours MTTF
135 °C
Nominal junction temperature
(T = +85 °C)
125 °C
Thermal resistance
(junction to ground paddle)
31 °C/W
Operating temperature
-40 °C to +85 °C
For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, Norwood, MA 02062
978-250-3343 tel • 978-250-3373 fax • Order online at www.analog.com/hittitemw
Application Support: Phone: 978-250-3343 or RFMG-apps@analog.com
HMC1160LP5E
v00.0814
MMIC VCO WITH HALF FREQUENCY OUTPUT
8.45 - 9.30 GHz
NOTES:
1. LEADFRAME MATERIAL: COPPER ALLOY
2. DIMENSIONS ARE IN INCHES [MILLIMETERS]
3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE.
4. PAD BURR LENGTH SHALL BE 0.15 mm MAXIMUM.
PAD BURR HEIGHT SHALL BE 0.05 mm MAXIMUM.
5. PACKAGE WARP SHALL NOT EXCEED 0.05 mm.
6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND.
7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED LAND PATTERN.
8. MAX PEAK REFLOW TEMPERATURE OF 260 °C
VCOS WITH FO/2 OUTPUT - SMT
Outline Drawing
Package Information
Part Number
Package Body Material
Lead Finish
HMC1160LP5E
RoHS-compliant low stress injection molded plastic
100% matte Sn
MSL Rating
MSL3
[2]
Package Marking [1]
H1160
XXXX
[1] 4-digit lot number XXXX
[2] Max peak reflow temperature of 260 °C
For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, Norwood, MA 02062
978-250-3343 tel • 978-250-3373 fax • Order online at www.analog.com/hittitemw
Application Support: Phone: 978-250-3343 or RFMG-apps@analog.com
4
HMC1160LP5E
v00.0814
MMIC VCO WITH HALF FREQUENCY OUTPUT
8.45 - 9.30 GHz
Pin Descriptions
Pin Number
VCOS WITH FO/2 OUTPUT - SMT
Function
Description
1 - 4, 6 - 10, 13 - 18,
20, 22 - 28, 30 - 32
N/C
No connection. These pins may be connected to
RF/DC ground. Performance will not be affected.
12
RFOUT/2
Half frequency output (AC coupled).
19
RF OUT
RF output (AC coupled).
21
Vcc
Supply Voltage, +5V
29
VTUNE
Control voltage and modulation input. Modulation
bandwidth dependent on drive source impedance.
5, 11, Paddle
GND
Package bottom has an exposed metal paddle
that must be connected to RF/DC ground.
Interface Schematic
Typical Application Circuit
5
For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, Norwood, MA 02062
978-250-3343 tel • 978-250-3373 fax • Order online at www.analog.com/hittitemw
Application Support: Phone: 978-250-3343 or RFMG-apps@analog.com
HMC1160LP5E
v00.0814
MMIC VCO WITH HALF FREQUENCY OUTPUT
8.45 - 9.30 GHz
VCOS WITH FO/2 OUTPUT - SMT
Evaluation PCB
List of Materials for Evaluation PCB EV1HMC1160LP5 [1]
Item
Description
J1 - J4
PCB mount SMA RF connector
J5 - J6
2 mm DC header
C1 - C3
100 pF capacitor, 0402 pkg.
C4
1,000 pF capacitor, 0402 pkg.
C5 - C7
2.2 µF tantalum capacitor
C8
0.01 μF capacitor, 0603 pkg.
U1
HMC1160LP5E VCO
PCB [2]
110225 eval board
The circuit board used in the application should use
RF circuit design techniques. Signal lines should
have 50 Ω impedance while the package ground
leads and backside ground paddle should be connected directly to the ground plane similar to that
shown. A sufficient number of via holes should be
used to connect the top and bottom ground planes.
The evaluation circuit board shown is available from
Hittite upon request.
[1] Reference this number when ordering complete evaluation PCB
[2] Circuit board material: Rogers 4350
For price, delivery, and to place orders: Analog Devices, Inc., One Technology Way, Norwood, MA 02062
978-250-3343 tel • 978-250-3373 fax • Order online at www.analog.com/hittitemw
Application Support: Phone: 978-250-3343 or RFMG-apps@analog.com
6