HomeWorks®
RF DIMMERS
Lamp Dimmers
048-017 1a 04.21.03
HomeWorks RF Lamp
Dimmer
DESCRIPTION
Indicator Lights
Tapswitch
HomeWorks RF Lamp Dimmers, used in both localized and optimized lighting control designs, function much like standard dimmers and switches, and have an integral microprocessor, allowing
them to be incorporated into the whole-house lighting control system. Communications with the system is accomplished via radio frequency (RF). RF Lamp Dimmers are useful in locations where single
plug-in lamps need to be dimmed or switched. RF Lamp Dimmers
incorporate advanced features such as fade on/ fade off, slow fade
off, and rapid full on.
Raise/Lower
Rocker
Lamp Cord
Receptacle
120VAC Plug
HTR-3LD-SW
MODEL NUMBERS
RF Lamp Dimmer
HTR-3LD-XX
300W Incandescent, 300VA Mag. Low Voltage
“XX” in the model number represents color/finish code.
®
JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
HomeWorks®
RF DIMMERS
Lamp Dimmers
048-017 2a 04.21.03
S P E C I F I C AT I O N S
• On a double-tap, lights go to full ON.
COLOR / FINISH CODES
Regulatory Approvals
• Pressing and holding the tapswitch slowly fades lights to OFF, beginning at
press.
Faceplate
Color
• UL Listed.
• CSA Certified.
• Light levels can be fine-tuned by pressing and holding the raise/lower rocker
until the desired light level is reached.
• FCC Compliant. Complies with the limits
for a Class B digital device, pursuant to
Part 15 of the FCC Rules.
Satin Colors®
Snow
Midnight
(code)
(SW)
(MN)
System Communications and Capacity
• Industry Canada Registered.
Power
Operating voltage: 120/127 VAC, 50/60 Hz.
• RF Lamp Dimmers communicate with the
HomeWorks RF processor through radio
frequency (RF).
• Each HomeWorks RF processor is capable
of directly controlling up to 64 RF dimmers.
Key Design Features
• Green indicator lights.
Environment
• Power failure memory: should power be
interrupted, the lights will return to
their previously set level prior to the
interruption when power is restored.
Ambient operating temperature:
0-40°C, 32-104°F, 0-90% humidity,
non-condensing. Indoor use only.
• Six-foot (1.8m) cord length.
• Tapswitch is programmable.
• On a single tap, lights fade up or down.
I N S TA L L AT I O N
Plug lamp cord into back of RF Lamp
Dimmer plug. Plug RF Lamp Dimmer plug
into any standard wall outlet.
®
JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
HomeWorks®
RF DIMMERS
Lamp Dimmers
048-017 3a 04.21.03
DIMENSIONS
Side View
Front View
15/16 in.
(24mm)
Cord Length:
6 ft. (1.8m)
4-11/16 in.
(119mm)
11/16 in.
(17.5mm)
2-15/16 in.
(75mm)
D I M M E R L OA D T Y P E A N D C A PAC I T Y
D I M M E R O P E R AT I O N
Status LEDs
(Dimmer only)
Indicate light level;
glow softly as night light
when light is off
Dimming Rocker
Press to Brighten
Press to Dim
Load Type
Capacity
Incandescent
300 W
Magnetic
Low-Voltage
300 VA
Tapswitch
Tap on/off
®
JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page
HomeWorks®
RF DIMMERS
Lamp Dimmers
048-017 4a 04.21.03
Home A: 2500 sq. ft. (232m ) or less - all RF devices within 30 ft. (9m) of RF
Processor
2
SY S T E M C O M M U N I C AT I O N N OT E S
RF Lamp
Dimmer
RF Maestro Dimmer
RF Designer-Style
Keypad
• RF Lamp Dimmers must be located within
30 feet (9m) of an RF Signal Repeater or
an RF Processor. Multiple repeaters may
be necessary to provide adequate coverage.
• RF Dimmers cannot be controlled by the
system and RF Keypads will not function
until they are addressed and programmed. See the HomeWorks Utility
online help.
30 Feet (9m) maximum
RF Processor
Home B: 2500 sq. ft. (232m2) or greater - some RF devices more than 30 ft. (9m) from RF Processor
RF Lamp
Dimmer
30 Feet (9m) maximum
RF Signal Repeater
RF Maestro Dimmer
RF Designer-Style Keypad
RF Processor
60 Feet (18m)
maximum
between RF
Processors and
Repeaters
30 Feet (9m) maximum
®
JOB NAME:
JOB NUMBER:
SPECIFICATION SUBMITTAL
MODEL NUMBERS:
Page